Cisco WAN :: 1841 - Routing Between LAN And WAN Works Except WAN
Oct 21, 2011
I am fairly new to Cisco IOS, yet I've managed to get it up and running on a Cisco 1841 to act as a router and firewall between WAN and LAN. Everything works *except* I am unable to ping or make any other connection from the router itself to the WAN. It will ping or telnet to the LAN, all LAN to WAN traffic is functioning properly, NAT is setup and functioning, WAN to LAN and inbound firewall is working, yet I still cannot ping or telnet from the IOS interface to anything on the WAN side (I've tried using different source addresses)
I am hoping there is something obvious that I overlooked, perhaps IPS is blocking the traffic? Do I need a specific route entry for the local device? I can post entire config if necessary, but would rather not if there is an obvious solution.
View 10 Replies
ADVERTISEMENT
Jul 13, 2011
I have 3 ASA's, all with the same config attaching to an 1841. One is hosted with Embarq and works fine, one with Comcast is not, the 2nd with a local cable provider is also fussy. Whats up based on the debug from the 1841? I'm getting little debug off the peer ASA from ISAKMP or IPSEC. You can carry the ASA's from one site to the next and the problem does not follow the boxes. This was working fine for several months, but now its not, and no.. the config did not change.
View 4 Replies
View Related
Feb 6, 2012
I'm just getting started with cisco kit so you will have to bare with me.I have a cisco 1841.i have a very wierd issue of routing...i cannot ping and browse through this.
View 3 Replies
View Related
May 31, 2013
I have a problem accessing my wireless router through VLAN sub-interface on my Cisco 1841 router. My hardware:
Cisco Catalyst 2960 switch (192.168.100.4 /24)
Cisco Catalyst 3550 switch (192.168.100.6 /24)
Cisco 1841 router (192.168.100.7 /24)
Asus RT N66U wireless router (192.168.100.2 /24)
Here's my network topology:
I have two VLANs - 10 and 20. 2 DHCP pools are configured on 2 1841's interfaces - 192.168.1.0 /25 and 192.168.1.128/26 with default router sitting on 192.168.1.1 and 192.168.1.129 respectively. No issues with obtaining IP address from any of those pools.Laptop connects to L3 3550 switch (switchport access vlan 10), which, in turn, connects to 1841 router through trunk (with VLANs 10 and 20 allowed).3550 is connected to 2960 through trunk with VLANs 10 and 20 allowed.Wireless router is connected to 2960.I can successfully ping my wireless router and outside world from 1841 from fa0/1 interface, but not from fa0/1.10 or fa0/1.20 sub-interfaces - all packets got dropped. My laptop can obtain IP from both pools (depending on port I connect it to), but can't ping my wireless router and anything beyond it.
I attach my configs:Cisco Catalyst 3550:interface FastEthernet0/1 switchport trunk encapsulation dot1q switchport mode trunk switchport port-security mac-address sticky speed 100!interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk!interface FastEthernet0/3 switchport access vlan 10 switchport mode access!interface FastEthernet0/4 switchport access vlan 20 switchport mode access!Cisco 1841:
ip dhcp pool Vlan10DHCP network 192.168.1.0 255.255.255.128 default-router 192.168.1.1 dns-server 208.67.220.220 domain-name home.local
!ip dhcp pool Vlan20DHCP network 192.168.1.128 255.255.255.192 default-router 192.168.1.129 dns-server 208.67.220.220 lease 0 12
interface FastEthernet0/1 ip address 192.168.100.7 255.255.255.0 duplex auto speed auto!interface FastEthernet0/1.10 description VLAN10 Sub Interface encapsulation dot1Q 10 ip address 192.168.1.1 255.255.255.128!interface FastEthernet0/1.20 description VLAN20 Sub Interface encapsulation dot1Q 20 ip address 192.168.1.129 255.255.255.192!
Routing table on 1841:
[code]....
View 19 Replies
View Related
Nov 8, 2011
I have a problem with may Cisco, it´s not start, only works the fan, the problem began when y turn down the Cisco and turn on again, but it´s not start. can something tell me what happen whit it.
View 1 Replies
View Related
Jun 11, 2012
I am currently trying to setup a GRE tunnel on a cisco 861. As part of a configuration template provide by an outside source I am recommended to use a sub-interface on the router but the recommended configuration does not work.
View 1 Replies
View Related
Dec 4, 2011
Is it possible that catalyst 4500 Supervisor Engine V-10GE WS-X4516-10GE works with WS-X4612-SFP-E?I know suprtvisor engine V-10GE is not support E-serious linecard, but when I use the configuration tool, I can choose these two products together. Is it a bug?I need novell IPX in this case, I find supervisor 6E & 7E are already not support, so I have no choice to choose V-10GE.
View 1 Replies
View Related
Nov 25, 2011
We have dlink dir320 router and cisco 877W.
The goal is to make a 877W to work as a wireless client of dlink dir320 and brigde the LAN&WLAN so than the LAN clients of 877W could take DHCP from Dlink 320 directly.
Here's the config of 877w:
!
bridge irb
!
dot11 ssid DLINK_SSID
[Code].....
View 1 Replies
View Related
May 21, 2012
i am first time to trying to make Vlans. I managed to do 2 vlans to SA520 to ports 1 and 2. But when i try to separatethem to SG300 with web management it doesnt work. Vlan 1 works fine, i untagged wanted ports and forbid vlan 2 ports.In Vlan 2 there vice versa, is this right way to do? Both Vlans has their own DHCP range as i do them to SA520.
View 2 Replies
View Related
Aug 12, 2012
Situation: Currently WS-C3750G-48TS-(S or E) switches are on stack. Now these units will soon EOL on Jan. 30, 2013 and Cisco recommends that
WS-C3750X-48T-S or WS-C3750X-48T-E will be used.
The question is: Will the new SKU works together in a stack with the old ones? Will there be no changes on the type of stacking cable to be used?
View 7 Replies
View Related
Sep 4, 2012
how this switch module works in 2911 router? I have two 2911 routers in HSRP configuration for redundancy with crossover cable between switch modules. OSPF running on routers.If active router loses its power and then comes back again, it boots first, its internal link to switch module comes up and it starts to forward packets to switch module. The switch module starts to boot only after router is ready. So I have outage of about 3-4 minutes. For our real-time applications it is way too long.
any way to start booting of the switch module before router gets ready?I understand I can boot it manually, but it is only after router is ready. Only way to get around it I found is to disable internal link and use router interface to connect to the switch module.
View 1 Replies
View Related
Aug 7, 2012
I have a 512MB USB Flash device and was able to boot the IOS on the C2960 from it.After that i tried to Copy the IOS file from the USB to the system flash, but it could not find the USB Device.At plugging in the device the systems tells me: "Transfer type 2 not supported" I configured the USB device in NTFS and FAT both are able to boot with the ROMMON, but the normal system does not accept them and i know i can do the copy over a TFTP from my laptop, but it is strange that rommon accepts the usb device and the system does not?
View 1 Replies
View Related
Nov 5, 2012
I've got a 3560-X that passes POST according to console, but there are issues nonetheless...USB console doesn't work. RJ45 works just fine. No status lights turn on at any point (e.g. syst, xps...). 10g network module is installed with a 10g LRM SFP. All lights on the module are amber. However, it passes according to POST. Switch passes traffic, obeys config, etc. Link lights on RJ45 ports work fine. This was brand new out of the box. Thinking about trying IOS reload..
View 6 Replies
View Related
Aug 14, 2012
4500 switch is connected to 2960 switch.
4500 config
Vlan 10
name Data
It has ip helper configured that points to DHCP.From 4500 switch port - port x connects to 2960 port.Port x is configured as trunk between 4500 and 2960.
2960 config
vlan 10
name data
All user ports are configured under vlan 10 and as access ports.Port x is trunk port connected frpm 2960 to 4500 switch allowing vlan 1 and 10 only.This switch has no default gateway configured.
We connected user PC on 2960 switchports and they were able to get the IP from DHCP server and were able to access the network? My question is how users on 2960 switch are able to access the network without ip default-gateway configured on 2960 switch?
View 6 Replies
View Related
Apr 18, 2013
I have a pair of OLD Cat6500's running CatOS:
WS-C6509 Software, Version NmpSW: 7.6(16)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Dec 22 2005, 16:37:19
System Bootstrap Version: 7.1(1)
System Boot Image File is 'bootflash:cat6000-sup2k8.7-6-16.bin'
System Configuration register is 0x2
I know these are no longer supported, but I have to ready them for migration. Recently a problem began with these switches. What happens is that when I telnet to them, I cannot authenitcate via TACACS. This works fine for all our other IOS equipment, just not for these 2 switches. The error is:" % Error in authentication" and then I get kicked back to the login prompt.
The odd thing is that when I connect to the switch via the console port, I can authenticate fine with TACACS.
CMS> /c 14
[Code].....
View 2 Replies
View Related
May 1, 2013
I have a Cisco 1841 that has an ADSL (ATM) card installed. It was previously used with an ADSL line to provide NAT routing for an office. Now I want to use it witha cable modem, which would mean abandoning the ADSL interface and instead routing between the two Ethernet ports.Between the Cisco and the LAN is a Linux transparent proxy. It provides routing between 192.168.1.0 (LAN) and 192.168.2.111 (Cisco LAN interface). The network looks like this:
Cable Modem(174.76.21.1)(gateway) --- (174.76.21.10)(WAN) Cisco 1841 (LAN)(192.168.2.111) --- (192.168.2.11) Linux Proxy (192.168.1.10) --- (192.168.1.0) LAN
For testing and diagnostics, I've connected a laptop to each FastEthernet port on the router. One laptop is configured with the IP 174.76.21.1 to simulate the cable modem gateway and the other laptop has the IP 192.168.2.11 to simulate the Linux proxy. From those systems I've performed the following diagnostics with the following results:
From 192.168.2.11
Ping 192.168.2.111 - OK
Ping 174.76.21.15 - OK
Ping 174.76.21.1 - Timed out
From 174.76.21.1
Ping 174.76.21.15 - OK
NAT translation to LAN IP's failing
There are some vestiges of the ADSL configuration, but I've cleaned most of it out and shut down the ATM interfaces. Here's my config:
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code].....
View 5 Replies
View Related
Sep 2, 2012
I have a Cisco 1841 router at home with version 12.4(13r)T advanced ip services. The setup is extremely simple:
1) PPPOE dialer to my service provider over ADSL
2) Nat overload on the dialer interface.
3) 2 V LAN s one for home network (wired) and one for wireless both v LAN's are connected through interface v LAN s respectively.
My problem is when I configure static NAT to map RDP or any other protocol to inside hosts this does n`t work.
"
ip nat source static tcp 192.168.20.3 2222 interface Dialer1 2222
ip nat source static tcp 192.168.20.3 3389 xx.xx.xx.xx 3389 extendable
ip nat inside source list 20 interface Dialer1 overload
"
When I open wire shark and sniff the traffic on home computer which is the one I`m trying to reach I can't see any traffic. And While performing Nat debugging I am also not able to see traffic going to that port (for example 3389).
View 7 Replies
View Related
Nov 16, 2011
I've got an 1841 router and am using NAT to expose certain IPs and ports to the outside world so that external users can see internal resources (namely, web sites). However, I can't seem to get it running such that I can visit the external IP address from inside the network and get the router to turn the request around so that it is redirected back inside the network. Shouldn't this be possible? Our previous router (a non-Cisco) was able to do this, but I can't seem to get the new one to do it.
A couple of key config lines:
interface FastEthernet0/0
ip address a.b.c.178 255.255.255.240
[Code].....
View 1 Replies
View Related
Nov 15, 2005
How to successfully implement OER w/ NAT? I will have an 1841 with the 4-port EtherSwitch module that will have 3 cable modems connected and utilizing cisco's OER to utilize all 3 links for outbound Internet traffic. However, I am concerned about NAT. The only other interface used on the 1841 will be the connection to the local LAN (inside). I'm thinking this will require a loopback, but I'm not finding anything on CCO to back me up. Is it possible to just let the CMs do NAT? 1 CM is a static IP and the 2 others are DHCP.
View 2 Replies
View Related
Jun 5, 2012
Am having an issue with my cisco 1841. I recently brought some IP Publics. Now that i need them i just can't use them, I don't know much about routers but till now have successfully manage to do some stuffs with the router after googling ,OK we already have some other ip publics and when i look at the config file i can see something like this:
View 3 Replies
View Related
Apr 9, 2013
I tried to connect a 1841 to a Linksys with a static route. I am able to ping from a computer in the 1841 to a computer in the linksys network, but I can't ping from a computer in the Linksys network to a computer in the 1841 network?
View 7 Replies
View Related
Jan 5, 2013
I guess i am just getting old and forgot how this works, or i have an IOS load with an undocumented feature in it.A customer of ours wishes to have their exchange server appear to the outside world on a seperate IP address as their public pool address is.in the past this has not been an issue, however in the current configuration we are unable to get the source address to appear per the NAT statement it always sources on the overloaded IP. below is the relevant NAT config, am i missing something, or have i hit a IOS feature? [code] There is a 45% chance i have forgotten everything i learned on the NOC desk and a 50% chance that it is somethine really stupid and 5% IOS is broken
View 5 Replies
View Related
May 2, 2012
I want to SSH into a Cisco 1841 router and depending on the suffix added to the SSH (i.e ssh myrouter.myroute.com 2002), would like it to forward this request to a terminal server.Can this be done? If so, how does one accomplish this? I have done something similar with RDP but I was not sure about SSH.
View 3 Replies
View Related
Oct 28, 2012
What is the command to shutdown a cisco 1841 (say, to add a module)? I know how to reload / reboot, but does not seem to find any command with an obvious name.
View 1 Replies
View Related
Jan 19, 2013
I have an 1841 running Advanced Enterprise Services 12.4(22)T3 that is functioning as a DHCP server and DNS server. What I am trying to figure out how to do is have the DNS service respond to queries about the clients of the dhcp service. I have successfully enabled it as a caching server for other requests, like "google.com" and "cisco.com", but what about the hosts on the local LAN?
As an example, let's say a Windows computer connects to the network with the hostname "computer" and receives an IP address from the 1841 with the domain name "test.net". I would like the 1841 to serve DNS queries for "computer.test.net" with the IP address that it assigned.
View 7 Replies
View Related
Mar 7, 2012
We have a Cisco 1841 router that requires 2 levels of access, at the moment we have network admins logging in with a single username via SSH and with privilege 15 but we also need our helpdesk to login to run certain commands but not chaneg anything
View 4 Replies
View Related
Jan 3, 2013
we've to configure our router 1841 to use both 2 interface Fe for two different vlan (also the second has to go on internet).
Actually we have int Fe0/0 configured with an ip address 192.168.1.1 for lan1 192.168.1.0/24 and we will use the second int Fe0/1 with another ip address like 192.168.2.1 for lan2 192.168.2.0/24.
see below configuration:
[code]...
View 5 Replies
View Related
Oct 7, 2012
I've never had a router's CPU suddenly hit 99% and just stay like it for hours even after a reboot. This router really does nothing with regards to CPU, I'm looking at it's CPU history (via SolarWinds Orion NPM software that we use) and it is arounf 1-3% all the time for the past 2 years.
I did a show debugigng and it seems no debugging is running
View 9 Replies
View Related
Sep 12, 2012
We upgrade our Internet service in our India office which required a new router. The local vendor suggested an 1841, so that is what we have. It has two fastethernet ports on it.
The ISP (Airtel) provided the following IP address information:
Public WAN IP : 122.181.23.200/30
WAN IP : 122.181.23.202SUBNET MASK : 255.255.255.252GATEWAY : 122.181.23.201Pri DNS : 125.22.47.125Sec DNS : 202.56.250.5
[Code]......
View 5 Replies
View Related
Dec 28, 2011
what is the latest firmware for cisco 1841 ? is firmware and router IOS image are same ?
View 1 Replies
View Related
Jun 5, 2012
We currently have a Cisco 1841 router with version 12.4(1c) of IOS using image c1841-ipbase-mz.124-1c.bin. Our goal is to make it so our router can fully support IPv6. The current IOS version cannot. I've seen a site that seems to indicate 12.4T does support with IP Base image but recently had Cisco tell me with the latest IOS release 15.1.4.M4 that I have to use either the "Advanced Enterprise Services" or "Advanced IP Services" image. Did Cisco just remove IPv6 from IPBase in later IOS releases?
Also I've seen conflicting specs on the max amount of Flash and DRAM the router can support. The following link shows that 384MB is the max for DRAM and 128MB max for flash. We're looking to upgrade ours from 128MB and 32MB respectively but as mentioned I've seen it where higher amounts are supported. In fact we bought a backup 1841 to have and it has a 256MB Flash card in it.URL
Last but not least. Where can I find a straightforward documention of this situation where we may have to upgrade our Flash and DRAM and then upgrading the IOS?
View 3 Replies
View Related
Apr 27, 2011
Here is my setup:
Cisco 1841 Software (C1841-ADVIPSERVICESK9-M), Version 15.1(2)T1, RELEASE SOFTWARE (fc1)
Cisco Internal IP:192.168.X.254
Cisco External IP 64.X.X.5 (NAT)
Netopia DSL Router:
Internal IP: 192.168.X.253
Exernal: 76.X.45.3
Now the DSL was installed a while back for a different need and now that need is gone. What Id like to is have the Cisco router do performance routing and send out internet traffic to either its own external IP or send it over to the DSL if it can get a better response. Presently, Since the Cisco is my gateway, the DSL line is sitting idle.
View 1 Replies
View Related
Jan 18, 2012
I have a cisco 1841 running on a 10Mbps Metro-E connection. I recently signed an agreement for a 100Mbps Metro-E. I am wondering if I will need to purchase a new router to support this new connection or will my 1841 be able to handle the traffic.
View 5 Replies
View Related
