Cisco WAN :: 4503 - HSRP Configuration Into Network
Feb 3, 2011
I want to run HSRP into my network.i am using two 4503 switch one is main and another one is standby. i configured V LAN into my switch and its running, now i want to configure HSRP. my configure is attach with this mail and my main switch gi2/22 is connect backup switch gi2/22 and all user is connect to both switch as like HSRP network.
I can use Standby ip
10.0.1.252 (vlan-1)
10.0.2.252 (vlan-2)
10.0.3.252 (vlan-3)
10.0.4.252 (vlan-4)
10.0.6.252 (vlan-6).....so on.
View 1 Replies
ADVERTISEMENT
Apr 7, 2011
I have two 4503 switches connected individually two 5510 Asa. My web server is under 5510 dmz interface. From Two 5510 Asa dmz interface there are two cables connected to two individual server farm switches.The web server in connected to this server farm switches.My local lan in connected to a cisco linksys switch. from that two cables are connected two individual 4503 switches on same vlan. i configured hsrp on this vlan. i pings the web server from local lan. when i unplugged one cable from Primary switch then it take 7-8 request timeout to recover into Secondary switch. it takes about 40 sec to switchover. it takes too much time. i also tune the timers but no luck. My Primary switch is also a Root Bridge.
View 7 Replies
View Related
Mar 4, 2012
i'm performing configuration PBR on catalyst 4503, but it doesn't work. [code]
View 21 Replies
View Related
Nov 13, 2012
I have the following topology:
2x 877 routers, one interface from each router (port Fa0 which belongs to the router internal switch) is connected to the 2960 switch, the switch himself configured with default settings, flat with one v LAN.
I have configured HSRP in the following manner: router A is 10.0.0.2, router B is 10.0.0.3, virtual IP is 10.0.0.1, take note that the HSRP configuration along with the IP address are configured on vlan1 interface.
Now when i connect a PC to the switch with static IP (10.0.0.4) and trying to ping 10.0.0.1 I'm not getting replies. i see on the PC, using wire shark, the icmp request goes out but on the primary router (and also on the backup) i can't see the icmp request (using debug ip icmp).
this behavior happens only when the HSRP is configured on interface vlan1, when configuring the same configuration on Fa4 (which is WAN interface) everything works fine.
View 4 Replies
View Related
Jun 12, 2013
I have 3945 router using the HWIC-4ESW module.I am not able to see the HSRP configuration commands under these interface.Does this module support HSRP ? If yes , do i need upgrade the IOS of router.
View 1 Replies
View Related
Feb 27, 2013
I have configure multiple vlans on both the core swithces below is the example, my question is how will be my VTP server configuration on the 3560E since both the core switches will have identical vlans HSRP 2 configured on them. Do I have to configure both the cores with same DOMAIN NAME ?
The core has VTP 2 so I cannot use primary and secondary option.
CoreSwitch1
interface Vlan713
ip address 194.43.86.251 255.255.255.0
standby version 2
standby 86 ip 194.43.86.1(code)
View 3 Replies
View Related
Mar 6, 2007
In the LAN network 4507R as core switch configured with several vlans.One vlan connects to the dual homed routers which in turn connecting to the single isp. I need to configure the HSRP for the internal vlans and the same time to use the load balancing or failover using the dual homed routers to the isp.
View 7 Replies
View Related
Aug 16, 2012
Having 2 router with 2 sub interface configured with HSRP. The server sending the data have the route default gw xxx.xxx.xx.252 HSRP address. But on of the routers did got HW problem so we did shut it down, R2 with IP xxxx.xxxx.xxxx.251, problem so the traffic didn't go there correct when was using the HSRP address some packaged went there but not all of them no blocks in the logs. But then we did change the server direct to to the working router R1 xxxx.xxxx.253 everything did start working fine again. was working fine. Logs i got in the router was max tcp half-open connections.
I am wondering if something wrong in the configuration below and why the traffic didn't got there correct when using the HSRP address. Its working fine when using R1 IP address. The devices are 2 Cisco 2620 routers.
R!1
interface FastEthernet0/0.192
description Prod_Inside
encapsulation dot1Q 192
ip address xxx.xxx.xxx.253 255.255.255.192
ip access-group Inside_Outside in
ip verify unicast reverse-path
no ip redirects
[code]...
View 3 Replies
View Related
Jul 8, 2012
recommend a cisco core switch and access switches in IPTV network infrastructure?I was ask to implement a network for IPTV system but i don't have idea what will be the model i will use.
Core Switch = Cisco 4503
Access Switches = Cisco 3560X
View 3 Replies
View Related
Aug 21, 2012
We have an OSPF network with four 6500 Distribution Switches. They are fully meshed and see each other as peers and are sharing routes. Off of one pair (Border) there is a setup of 3750G siwtches that go off to another network and they do not run OSPF. Between the Border Dist and the 3750G Switches we run HSRP. The 3750G side uses HSRP GP 192 and the Dist Side uses HSRP 192.There are static routes on the 3750G pointing to the Dist HSRP address to get back to network.Pings fail from the OSPF side to the HSRP address on the 3750G side.If I do a trace from the OSPF side to the HSRP address it hits one border dist switch then the other and fails.If I have static routes on both border dist switches pointing to the HSRP on the 3750side, do we need to change the metric on one dist so that it is preferred over the other or should the router Id take care of that?
View 1 Replies
View Related
Feb 29, 2012
I have a Cisco 4503 with a supervisor 6 engine. I want to create a trunk between the router and a switch. when I do :
switch port mode ? Access
Dot1q-Tunnel
Dynamic
Private-v lan
Trunk
I thought I should see :
switch port mode encapsulation dot1q
switch port mode trunk
Am I missing something I do not see where I set the encapsulation.
View 1 Replies
View Related
Oct 4, 2012
I have a doubt regarding MIBs. I dowloads the MIBs for Cisco 4503 for a specific IOS. But the folder is divided by v1 and v2.
What does it mean v1 and v2? The version of SNMP?
So if I enable just SNMP Trap (''snmp-server enable traps.....'') I should use MIBs v1 but if I enable also the number of Retries and Timeout ( ''snmp-server inform retries...'' and ''snmp-server inform timeout...'') I sould use MIBs v2.
View 2 Replies
View Related
Mar 21, 2011
installing IOS for cisco 4503 e catalyst switch. The base ios image file has been deleted. Installing the ios and from where can I download the ios verison.The device has 2 10 Gig uplinks and I have access to console of the device.when i boot up the device it comes "rommom >"I do have tftp server and i have also configure the IP in fast ethternet mgmt port.
View 2 Replies
View Related
Jan 18, 2012
There is some way to increase the speed of changing the interface state from DOWN to UP when the cable is connected. I need to configure a port of Cisco 4503 in a way that when a cable is connected the port goes immediatly UP.
A solution can be to keep Cisco interface always UP and I remember that with "no keepalive" command to the interface configuration it was possible. But I tried and nothing happens.
View 12 Replies
View Related
Jan 23, 2012
I'm looking for a SNMP set command that clear the MAC Address table on a Switch Cisco 4503.
View 3 Replies
View Related
Oct 16, 2011
just got a new supervisor 4 engine for this catalyst 4503 switch that has ios 12.2 (53) SG installed on it. That's quite a bit above the 7.6 i was working with. I'm having a couple issues now. first, I read that it is supposed to be sending out broadcasts automatically to get it's IP address but it doesn't seem to be. the module i'm plugging into there is ws-x4448-gb-rj45, a 48 port 10/100/1000 module in case it matters. it works other than that. I can plug two computers in and see them and i can plug the network in and they'll both get addresses and internet, but i need an IP on the switch. is there a way to send a manual request for broadcast out or somehow set the IP manually? (I know I can do it in the rommon, but that doesn't seem to do anything)
also, the last module in the switch is a 24 port poe ws-x4224-rj45v. the module is recognized, the status light green, the "show interface status" lists it, but it doesn't recognize anything plugged into it. the supervisor is not configured at all yet, so maybe that has something to do with it, but the other module, like i said, works.
View 5 Replies
View Related
Sep 16, 2012
I need to implement over an ethernet link L2 tunnel because I want to isolate another VLANs domain.On the first side I can use the command : sw mo dot1q-tunnel on a new C4503 on the other side I cannot configure the command : sw mo dot1q-tunnel.
the other side is an old C4503 we upgrade the flash with a compact flash to upgrade to a new IOS v15 but the command doesn't exist also.I red the cisco feature navigator feature and I am sure the dot1Q-tunnel is available on my image : cat4500-ipbasek9-mz.150-2.SG.binso I don't know why I can use it.
View 1 Replies
View Related
Feb 9, 2013
We have microsoft servers and other application servers (around 12 in nos) which should have gig connections to the access switch. In turn this access switch will be connected to our distribution switch 4503. Which model of access switch best fits from the below 3 models. It should be cost effective as well.
WS-C2960 S-24PS-L
WS-C2960-24TS-L
WS-C3560G-24TS-S
View 8 Replies
View Related
Jan 11, 2012
I am installing a connection between Brocade MLX and Cisco 4503 using SE and SVI's. Below is the config for each. Am I missing anything like MTU Ignore or something along that nature?
*** Cisco 4503 (v15.01) Config ***
VLAN 35
name EOC_Gi1/2
[Code].....
View 3 Replies
View Related
Sep 2, 2012
I am trying to connect a 6509 switch to a 4503-E switch using single mode dark fiber over a distance of less than half a mile. Although a routine task, it does not work..We have a care 6509 switch where we concentrate all of our dark fiber connections for our remote sites. The 6509 switch already has 30 remote sites, most of them with 4503-E switches, connected in this way therefore it is a tested scenario. For the connections we use the GLC-LH-SM SFPs on both switches. Out of these 30 sites we had a similar problem with two of them, which we solved with the use of CWDM SFPs. With the CWDMs the fiber came up right away. However, I cannot keep using this solution because it is way too expensive! I had the losses of the fiber measured end-to-end and they are negligible (>0.5 dB).
In this latest case, like I said, we could not bring the connection up between the core 6509 switch and the 4503-E switch using the GLC-LH-SM SFPs. I then replaced the 4503-E switch with a 3560 and the link came up! Then I tried using a CWDM-SFP in the 4503-E, while keeping the GLC-LH-SM SFP in the 6509 and the link came alive again! Of course we already tried replacing the fiber patch cords with no luck. [code] I find it very weird for the link to work with the 3560 or with a CWDM in the 4503 but NOT with the SFP in the 4503!
View 6 Replies
View Related
Jul 8, 2012
I have a 4503 switch (in L2 mode) running 12.1 hooked into a C2950 running 12.1, using regular 4 pair Cat5e cables to connect between them. The 4503 has Gigabit port 2/1 trunking to the 2950's Fa port 0/13.
When I set the duplex mode to DUPLEX FULL and SPEED to SPEED 100 on both switches (for their trunk ports) the link fails, and my 4503 loses connectivity (since it gets it from the 2950).
Here is my config from the switches (per description):
The 4503:
interface GigabitEthernet2/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,2,100-140
[Code].....
Note, this is the only mode that works (which seems to work fine, but I get TERRIBLE throughput for anything that goes over the 2950.
View 5 Replies
View Related
Dec 14, 2011
we have Core-Siwtch 4503 in the main building which is connected to another Core 4503-E in another building ,, now our PCs connected to the 4503-E ,,, any XP M/C can pick an Dhcp-ip but and M/C run Win.7 Cannot !!
action taken :
1st we try to connect our win 7 pc in the node which was connected to xp M/C ,, and it didnot take ip from the DHCP . ,, 2
2nd we ensure from the core-switch configuration and its normal with no mistake
3rd trying to use tool from Microsoft Fix-it Center whih name is ( Microsoftfixit 50475 ) which is just .msi file but the problem face us is that this tool donnot accept to run on win 7 cause its made for vista .
4th after some researchs we notic that there is some modifications have to be performed on registery by disabling the dhcp broadcast flag we did it but nothing change yet
5th now we are waiting to perform another action which is Disable the IP Helper service in win 7
View 6 Replies
View Related
Jan 9, 2012
Currently we have cisco 4503 switch in one of our location without redundancy which servers below,
300 user (desktop & ip phones)
5 vlans
15 access switches are connected
one L3 connectivity.
Actually i want to understand is it really necessary to have 4503 or we can go for 4900 series as we are planning to have redundancy in distribution segment.
Which is the best L3 switch in the above scenario and how to measure the overall performance of the current 4503 switch...
View 4 Replies
View Related
May 18, 2013
After deleting configuration with „write erase“ and reloading, our Cisco Catalyst 4503 with version cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin, and licence ipbase, doesn't recognize any command regarding SSH. We tried configuring SSH key with „crypto key generate“, but that command is not recognized either.
View 1 Replies
View Related
Sep 13, 2011
We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies
View Related
Nov 30, 2011
I need a 10G support on 4503 chassi with SUP II plus TS.Is any of the 10G line cards i.e. 4712 or 4606 supported on SUP II plus TS on 4503?
View 4 Replies
View Related
Feb 14, 2012
We had a core switch(30 vlans) in our environment and it's noticed that CPU utilization of the core switch is showing high during recent days. I have checked logs and processes, but couldn't find the root cause. The issue found only in the office hourly only(after that the cpu utilization is idle and normal). I have already referred the following link to troubleshoot the issue " [URL]
see the following outputs from the core switch
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
30 6687557041432420936 466 47.52% 47.10% 45.98% 0 Cat4k Mgmt LoPri
55 30667074884269560256 0 45.36% 45.50% 45.85% 0 IP Input
29 28552856922870089254 0 3.59% 3.50% 3.57% 0 Cat4k Mgmt HiPri
[code]....
Note: Each Invalid source mac entry in each day from same port (above is the output after clearing logs before 3 days)
My queries regarding the issues are following
1) How can we find root cause regarding the high cpu utilization?
2) Is a single invalid mac address makes the cpu highly utilized for suppressing it?
View 10 Replies
View Related
Dec 17, 2011
I am working with a Catalyst 4503-E with a Sup7-E. I'm trying to enable Netflow, and I have read the following guides: Catalyst 4500 Series Switch SW Configuration Guide, Release IOS ...
I have also enabled Netflow in IOS 12.1/12.2 and figured the process was similar (It seems to be). CEF is enabled, and I have all the pre-reqs according to the document above, however, the flow commands don't exist, they simply say "command unrecognized". I have included my sh version below.
sh version (edited):
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
[Code].....
View 2 Replies
View Related
Oct 2, 2003
I have at the core a CISCO 4503 and need to connect various 3COM 3300/4400/4900 access switches thru fiber. The problem is that the Cisco core 4503 switch fails to recognize only the 4900 3com switches ie the link status shows down. The fiber multitude link is tested and OK.The modules on both the switches ie 1000baseSX are also tested and ok.
The Cisco switch has a 6port gb ic with 1000baseSX moules and the 3COM 4900 has a 4-port 1000baseSX module.
View 3 Replies
View Related
Jan 13, 2012
We have two core switches in our network (Cisco WS-4503). HSRP is working as Active-Standby mode. Recently it has been found that core 1 (which is in active mode) shown high CPU load (60% - 100%). Also found that the below mentioned process takes more CPU. Our network consist of around 30 Vlans. We have already checked for the solution in Cisco website [URL] but couldn't find exact reason. see the below outputs for core 1 switch.
Core1# sh processes cpu sorted
CPU utilization for five seconds: 55%/3%; one minute: 65%; five minutes: 71%PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 30 1606933521086983644 147 24.79% 29.93% 35.85% 0 Cat4k Mgmt LoPri 29
[Code]....
View 3 Replies
View Related
Mar 22, 2012
I have a 4503-e with WS-X4013+TS supervisor and WS-X4548-GB-RJ45 card. I purchased a WS-X4648-RJ45-E card and installed but IOS says its unsupported. Supervisor is running 12.2(46)SG software and 12.2(31r)SGA firmware. Obviously I'm hoping this cars can be supported somehow. Do I need to upgrade software or firmware, or return the linecard and get equivalent supported card? Oh, system is running Catalyst 4500 L3 Switch Software. (cat4500-IPBASEK9-M)
View 6 Replies
View Related
Nov 7, 2011
We have a gateway on a 4503, say on port 2/1, and we only want the other devices that are plugged into the 4503 to be able to talk to the gateway and thats it. The other devices are Motorola TUT DSL devices and they plug into the 4503 directly.
Normally "switchport protected" would make this very easy to keep stuff on one port from talking to other ports but with 4500's you are not able to do that command. So we implemented a MAC Access-List Extended ACL. Here is what we did
mac access-list extended BLAH
permit #host 0000.XXXX.YYYY any
interface range fa 2/5 - 20
mac access-group BLAH out
The MAC address 0000.XXXX.YYYY is the MAC address of the gateway that is plugged into Fa2/1 and the DSL TUT devices are plugged into ports Fa2/5-20. We would think that this config would only allow devices on the TUT DSL to talk only to the Gateway but we don't really think this is happening. The TUT devices are learning about MAC addresses that are on other TUT devices.
View 1 Replies
View Related
Mar 30, 2012
Do the cisco 4503 switches support virtual clustering feature ? I have a requirement where switch ports on two different 4503 switches need to combined in the same Link aggregation group . This is needed because the firewall notes say that the aggregated interfaces need to be conected to a single switch and combined in the same LAG . So according to the diagram below , the interfaces marked RED need to be in the same LAG in the switches , same for the interfaces marked BLUE . I have done the same setup using Juniper switches where it uses VIRTUAL CLUSTERING to group the different switch ports in the same LAG.
View 2 Replies
View Related
