Cisco WAN :: 6509 - Connecting To Other Switch Using VLAN 1002
Feb 19, 2012Are there any solution to connect VLAN 1002 configured in non-cisco switch to connect to Catalyst 6509?
View 2 Replies
ADVERTISEMENT
Cisco Firewall :: 6509 Core Switch - How To Create DMZ Vlan
Oct 31, 2012I need to create a DMZ Vlan. Core switch is a 6509. FW is an ASA5520. Need to create a VLAN for DMZ purposes for outside facing servers. NAT is used on ASA.
View 7 Replies View RelatedCisco :: Core Switch 6509 - Route Each Vlan To Exit From Spacific DSL
Jan 26, 2012i'm already has one internet connection is connecting directly to the Core Switch 6509,Vlan 500 (1921.168.1.0) and the Switch is route any internet request with default route:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
The Problem: We have a new internet connection with new Vlan 600 (172.16.1.0) another ISP/ with another DSL router, so i need your kindly support and suggest how to connect both of them to exit from the Core Switch 6509. is it ok if i make another default route to the Next hop to the new DSL router as:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
10.80.10.10 is --> Next hop for the new DSL router internal IP.
is there any way like default route , route-map or any other features to :
route Vlan 500 (192.168.1.0) to exit from DSL 1 --> 10.170.10.10
route Vlan 600 (172.16.1.0) to exit from DSL 2 --> 10.80.10.10
Cisco LAN :: 6509-e Switch And IDF Closets Have 3750 - Creating Isolated VLan
May 6, 2012My core switch is a 6509-e and my IDF closets have 3750's.I have a couple of vlans currently setup, that can communicate with each other.VTP is setup Client/Server where as my core is Server, all IDF's are Client.
What i'm trying to do is create an isolated VLAN. I want to setup a DHCP scope and use helper address. When i plug in a client to that VLAN, i want it to get an IP, but not have any other network access.
Is this possible to do without switching to Transparent mode? If not - what reprocussions will i see by switching to transparent mode?
Cisco Switching/Routing :: Slow File Transfer Speed In Same Vlan Of 6509 Switch
Mar 16, 2013I am getting very slow window file transfer speed (4 Mbps per second) between two connecting servers in Cisco 6509 switch. I have connect the two laptops in 6509 switch in same module using the same vlan and try to copy the files from one laptop to another and vice versa and got the same speed on 4 to 5 Mbps per second. Switch utilization is not more than 10% and both the laptops are connected in 1 Gbps full duplex.
I have checked by removing the gateway in both laptop but the output is same.
Cisco Switching/Routing :: 6509 - 802.1x And Voice VLAN / Enable Dot1x On User's Ports On The Switch
Sep 17, 2012I have a Cisco 6509 with IOS "s222-ipservicesk9_wan-mz.122-18.SXF16.bin"I need to enable dot1x on user's ports on the switch. each user is connected to the switch through the IP phone.
I just found out that I can not enabled dot1x on trunk port. I have tried to use "switchport voice vlan " but I got:
Switch(config-if)#switchport voice vlan 123
Command rejected: Gi7/20 is Dot1x enabled port.
let me know what should I do to get dot1x working?
Note: I have connected a laptop directly to the port and dot1x is working fine.
Cisco Switching/Routing :: Use Of Vlan 1002 - 1005
Aug 14, 2012i've heard that it is now possible to use Vlan 1002 -1005, perhaps only on certain devices.
View 3 Replies View RelatedCisco Switching/Routing :: 1002 ASR Sometimes Vlan User Will Not Be Able To Access
Apr 2, 2013We are having Cisco router 1002 ASR and 2841 switch. Some times perticular VLAN user will not be able to access the network but from the same switch others VLAN users can able to access. We were getting ARP entries in router but we cannot ping the IP's. Even we clear the ARP entries. Once we restart the switch users can access the network. We have changed vlan ports, uplink too. but problem not solved. and we observed CPU utilization will be going 70-80% some times and at same time switch hangs.
View 3 Replies View RelatedCisco Firewall :: 6509 / FWSM VLAN Configuration Mismatch And Some VLAN Deleted
Aug 12, 2012We have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level. All VLAN Gateways are configured in context level.
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During migration of devices from one Dc to a new DC we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
During the activity ( Primary switch movement )We powered off the Primary switch and mean time before shifting into new Data center We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
Later we had moved Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE and primary device was not responding and devices went off network and immediatly we removed the VSL link and brought up primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original VLAN ip 10.200.112.1 has become 10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.
Cisco Switching/Routing :: 3750 - Extending VLAN To Remote Switch That Already Has VLAN ID In Use
Jan 10, 2013I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
Cisco WAN :: 6509 Match Vlan Is Not Supported For Interface
Mar 13, 2013I have a 10Mbps connection link which I will like to reduce to 5Mbps on a 6509 switch as indicated in the config below. [code] After applying the service policy on the vlan interface, i got this "match vlan is not supported for this interface". I actually tried the rate limit command but I cant see the effect using the speedtest.
View 2 Replies View RelatedCisco WAN :: Sup720-10G 6509 - Multicasting In Same Vlan Broken
Oct 9, 2011Currently we do not have multicat routing enabled on either of our 2x Sup720-10G 6509 Switches. We have no intention of doing so either. I am looking for clarification on how mutlicasting operates within a Vlan.
IOS: s72033-ipservicesk9_wan-mz.122-33.SXH2a.bin
Our Vlan has IGMP snooping enabled. Here is the output.
6509Switch#sh ip igmp inter vlan 25
Vlan25 is up, line protocol is up
Internet address is 10.1.1.254/24
IGMP is disabled on interface
we do not want to disable IGMP due to this one concern that I can't find documented. If we disable IGMP snooping on the vlan, what happens to multicast packets with a TTL > 1. Do they get flooded to the entire switch and all Vlans? Or does it stay within the Vlan?
Cisco Switching/Routing :: How To Backup VLAN DAT On 6509
Feb 5, 2013We backup the running config on the 6509 does it also backup the vlan.dat as well?I tried command dir/all and just dir but did not see the vlan.dat listed
View 6 Replies View RelatedCisco Switching/Routing :: 6509 - How To Configure New VLan
Nov 1, 2011I have a Cisco 6509 connected (gig3/17) to a Cisco 3560 G switch (Gig 0/28). The 3560 switch Gig 0/26)is connected to a distribution switch on another network. The ip address on my 6500 is 10.120.11.244 255.255.252.0 and the ip address on my 3560 is 10.120.11.211. The ip address given to me by the other network is 10.162.20.10 255.255.255.252. How do I configure the new vlan in this situation and the ip address given to me.
View 4 Replies View RelatedCisco Switching/Routing :: 6509 Vlan Configuration Missing?
Jun 17, 2012After a abrupt power cylce of 6509 switch, vlan configuration got missing. Switch has not crashed.
View 4 Replies View RelatedCisco WAN :: Rate Limiting Configuration On Vlan Interface On 6509?
Feb 10, 2011I have used the following basic configuration to do rate limiting on a vlan interface on a 6509:
access-list 100 permit ip any any
class-map match-all ratelimit
match access-group 100
policy-map ratelimit-10Mb
class ratelimit
police 10000000 428750 conform-action transmit exceed-action drop
[code]....
How do I combine the two correctly to give me a vlan port rate limited at 10Mb up and down, but still setting aside (dynamically) 2Mb for voice?
Cisco Switching/Routing :: STP 6509-E On Vlan 1 In A Heterogeneous Network
Aug 15, 2012we have an heterogeneous network with Cisco devices (6509-E, 3750G and 3560) and Alcatel 6850 devices. We have to enable a PTP Wifi line as a backup for the fiber line between two buildings. For this purpose, we have connected a wifi device to GigabitEthernet 0/47 of SWIHGJ1 and configured it as: [code]
View 2 Replies View RelatedCisco Switching/Routing :: 6509 Vlan Flapping Between Port-channels
Mar 10, 2012We have a pair Cisco 6509 switch in which 2 * 48 Port 1G line cards and 1 * 16 Port 10G line Card, FWSM and Sup 720 are installed.We have Cisco UCS and HP Blade servers.Cisco UCS servers are connected to Cisco 6509 switch using Fabric Interconnect, and HP Servers are directly connected to core switches.Recently the team made many changes in the network. Upgraded the IOS in Cisco 6509 switch, Configured Port profiling , MAC Pinning , HBA Cards to UCS / Nexus 1000V Infrastructure. After this change they lost the connectivity to UCS and HP Serers. Every tower is checking at their end.
The Network Team has reverted back the core switch with old IOS , but still the problem persisit.I could only see the following error log in the core switch. There are two port-channels one between core 1 and core 2. The other is between core switch and FWSM module. [code]
Cisco Switching/Routing :: Setup VLan Between 6509 And 2621 Router?
Oct 25, 2011I need to setup a vlan between the 6509 and 2621 router. This needs to be a VLAN (200) the runs between the devices that uses DOT1Q trunking. The end result is all the networks (vlans) on the 6509 can talk to the LAN on the 2600 (10.133.22.0 / 23) and visa versa.
Device 1
6509 with CatOS / IOS
Config I did on the MSFC:
Interface Vlan 200
ip address 10.10.10.1 255.255.255.248
[code]....
Cisco Wireless :: 6509 - WISM Not Connecting After Reboot
Apr 7, 2013We have a WISM in a 6509. The 6509 lost power (the UPS failed) and upon reboot the WISM isn't allowing AP's to connect. The WISM is blade 4. Upon consoling in, I get this error message for all 8 ports: 42w6d: %EC-SP-5-CANNOT_BUNDLE2: Gi4/1 is not compatible with Po407 and will be suspended (trunk mode of Gi4/1 is dynamic, Po407 is trunk)
View 13 Replies View RelatedCisco Switching/Routing :: Set Port Vlan On 6509 Running In Vtp Client Mode
Jan 14, 2013I'm working at a company that has several 6509 switches running CatOS. They have two of the 6509's running in vtp server mode and the rest as clients. I set up a new vlan from one of the vtp servers and it propagated out. The problem comes when I try to assign a port on one of the vtp clients to this new vlan. It gives me an error that the switch must be in vtp server mode to add/delete vlans. I'm not trying to add/or delete a vlan just trying to add a port into an existing vlan. I'm hesitant to put the switch in vtp server mode. Is this a CatOS thing or is there a specific command to accomplish this?
View 5 Replies View RelatedCisco Switching/Routing :: 6509 - Can't Change Native Vlan On Trunk Port?
Jun 6, 2012I have several closets with Cisco 3560 on the edge that I'd like to change the vlan that's used for the management vlan on each. In the core I have a Cisco 6509 with Sup720's.
I'd like to do this by changing the native vlan on the trunk port on the core 6509 interface that connects to the 3560. and leave the management vlan on the 3560 as vlan 1.
Seems trivial but what I tried didn't work and I didn't have the window to troubleshoot. I'll paste the simplified configs for the interfaces below
!
6509 configs:
!
interface Vlan50ip address 172.16.50.2 255.255.255.0!interface FastEthernet
[Code]....
Cisco Switching/Routing :: Disable Administrative Native Vlan Tagging On 6509?
Dec 13, 2012We have a problem with CDP packets on sent by our Cisco 6509's. Unlike our other Cisco switches (4948G, 5020, etc.), the 6509 tags administrative traffic on the native vlan. As a result the CDP packets are sent with an 802.1Q header with a tag of 1. The other switches send the CDP packets untagged on the native vlan. This causes problems because we have non-Cisco devices in our lab that also receive and send CDP, but they do not process the packets that are tagged by the 6509. They see the packets from the 4948 and 5020 just fine.
How can I disable the administrative native vlan tagging on the 6509? Here is the current setup:
nwkdev-6509-1#show vlan dot1q tag native
dot1q native vlan tagging is disabled globally
nwkdev-6509-1#show interfaces gigabitEthernet 1/9/1 switchport
[Code].....
Cisco Switching/Routing :: Net-flow Not Reporting Egress Traffic On 6509 Vlan
Nov 27, 2011We have a pair of 6509 working in a VSS configuration (IOS 12.2(33)SX5). The 6509s connect to a pair of ASAs (7.2 code) running in an Active/Standby setup. These ASAs in turn connect to routers going to remote sites. I have configured Netflow on the following VLANS,
VLAN 10 - Servers Vlan
VLAN 9 - Transit/ASA VLAN (connects ASAs to 6509s). All traffic originating from any VLAN on the 6509 crosses this VLAN in order to reach remote sites and vice versa
I configured the netflow source VLAN 11 although I am not collecing any netflow from it.Although I have been getting lots of Netflow info, I noticed that netflow for traffic originating from any user VLAN on the 6509s going to any remote site via TRANSIT/ASA VLAN(9) does not get reported, I even tested with 4 GB traffic but no result. Only reverse traffic (i.e. from remote site to user VLAN) is reported as it traverses the Transit VLAN (9).
I read somewhere that egress netflow is not supported in 6500, but isnt traffic originating from a user vlan to a remote site via the transit VLAN (9) considered ingress with respect to the transit VLAN (9)? I would like to know whether bidirectional Netflow is supported on 6500 VLANS. I have mimimum control on routers beyond the ASAs, and since these ASAs run 7.2 code netflow is not supported, and Monitoring this Transit Vlan gives me extremely useful info.
I do get netflow biderectional traffic from the Server Vlan 10, but I think it is correlated by the netflow collector from vlans 9 and 10. [code]
Cisco Firewall :: 6509 / Interface VLAN Stop Responding On FWSM Automatically
Aug 8, 2012i have been facing strange issue on FWSM (6509 switch). we have created a vlan inteface for server farm on fwsm and its stop responding automatically and we need to give shut/ no shut command under that interface to back into normal .
View 11 Replies View RelatedCisco Switching/Routing :: Connecting 5548 Pair To 2 6509 Core Switches / No Vss
Jun 8, 2012connecting a 5548 pair to our core 6509s. Just want to be sure we don't introduce any issues into the network.The 6509's are connected and perform all the routing. Essentially, we're moving away from a 3750 stack in the data center and the 5548s are the replacement. We'd want to limit the vlans to the specific server network vlans. Our current setup is a port channel between the 3750 and each of the 2 6509s for redundancy. I'd like to use the same functionality when we connect the 5548's but I'm looking for what the config should look like to ensure no spanning tree loops are introduced and that it is configured optimally.
View 1 Replies View RelatedCisco WAN :: Configure SVI On 6509 Switch?
Apr 9, 2012How to config SVI on Cisco 6509 switches??
View 1 Replies View RelatedCisco WAN :: Unable To Login At 6509 Switch
Jul 4, 2011We are unable to login at Cisco 6509 switch, due to username and password not working. We have tried to recover the password as per Cisco document, but that is also not working. This switch is our Primary Switch in our network.
View 8 Replies View RelatedCisco WAN :: Enable Option 60 On 6509 Switch?
Nov 14, 2011We have Cisco 6509 switch, in which DHCP is enabled and now we have WDS(Windows Deployment server) that needs option 60 to be enabled on DHCP scope for deplyoing OS remotley to PC's. Where to get sample configuration to enable the option 60.
View 1 Replies View RelatedCisco :: Connecting 2 Pc From One Vlan?
Aug 21, 2012i have only one switch 2950 and create one vlan (for example vlan100). how can i connect two pcs with two different ip to each other? in this example we cant use private vlan.
View 7 Replies View RelatedCisco WAN :: 6509 - MAC Address Flapping In Core Switch
Dec 28, 2010I am getting following error in Cisco 6509 switch.BUt there is no impact in the switch.
: %MAC_MOVE-SP-4-NOTIF: Host 0000.0c07.ac01 in vlan 694 is flapping between port Te8/1 and port Te7/1
29:33.959: %MAC_MOVE-SP-4-NOTIF: Host 0000.0c07.ac01 in vlan 269 is flapping between port Te7/1 and port Te8/1
[Code].....
Cisco WAN :: VPC Configuration Template With Two Core 6509 Switch
Jan 3, 2013What is the VPC configuration template with two core 6509 switch.Pls find the attachment for Network topology.
View 3 Replies View RelatedCisco WAN :: 6509-E / ACLs Missing After Reload Switch?
Jan 1, 2012We had an power shutdown activity last week, due to which one of the core switch was turned off and ON .After the core switch was turned ON, we had found some of the ACLs missing which were bounded in VLANs. We had given write command before this power shutdown activity.We need to find the root cause for the same.
Switch Model-WS-CISCO-6509-E.