Cisco WAN :: 7206 - PPPoE B-RAS And Framed-route Attribute
Mar 27, 2012
I'm configuring a Cisco 7206 NPE-G2 as B-RAS for PPPoE over a Gigabit Ethernet interface. Everything is OK but I'm having problems when i try to pass the framed-route attribute from the RADIUS to assign a /29 sub net to a PPPoE client, the 7206 seems to skip it and no route is installed in the routing table.
This is the configuration:
upgrade fpd auto
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]......
I tried also with Cisco-AVpair ip:route with the same results.
View 3 Replies
ADVERTISEMENT
Mar 2, 2011
I am attaching my current network topology, My problem is that i am having mpls & p2p link terminated on the 7206 router left side of diagram. now my problem is if i apply PBR on this 7206 router & tracer any host which are on right side of the diagram, it drops on IP 10.1.1.1..ideally it should go to my Core switch on right of the diagram.
View 8 Replies
View Related
Sep 5, 2012
I have a MPLS cloud in our data center. I want one network coming into our core router to have a different default route than the other networks coming in. I'm getting hits on the acl but the route isn't applied and goes to the default route that is configured in the router. I have other PBR for setting local-preferences and as-paths and they are working fine.
The router is a 7206 Version 12.4(11)T3
!
ip route 0.0.0.0 0.0.0.0 1.2.3.4
!
ip access-list extended 2nd_Default_Route
[Code].....
View 1 Replies
View Related
Apr 2, 2013
I have a cisco 890c-w with routing and wireless，contain 8 switch ports（fastethernet 0 - 7），one 100m route port（ fastethernnet 8），one giga port gigagethernet 0
configuration pppoe，dialer1 can get WAN IP。
0-7 ports in vlan2，vlan2 config ip add 192.168.1.1
In router，ping 8.8.8.8 is ok，but ping 8.8.8.8 source 192.168.1.1 can not ok，so my pc can not go internet through 0-7 ports。
I think routing problem，but don't find reason
service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot system flash c890-universalk9-mz.151-4.M2.binwarm-rebootboot-end-marker!!enable password password!no aaa new-model!memory-size iomem 15service-module wlan-ap 0 bootimage autonomouscrypto pki token default removal timeout 0! ip source-route!ip cefip name-server 61.234.145.102ip multicast-routing no ipv6 cef!multilink bundle-name authenticatedvpdn enable!vpdn-group PPPoE!license udi pid CISCO892C-
[code]....
View 4 Replies
View Related
May 17, 2012
Recently I've installed this particular cisco ASA5510 at a client site (Head office), along with remote access VPN setup. All most 32 branches(one user from each branch) connect to the head office via remote access vpn.
Further I've used the "vpn-framed-ip-address" command along with a dedicated ip address, under each "user attributes", so every time when a user connect, he used to get the same ip address from the VPN pool.
My problem is sometimes this setup works fine, but once in a while the same ip address will be assigned to two different users at the same time, despite of the "vpn-framed-ip-address".
View 2 Replies
View Related
Mar 29, 2012
I have a running L2TP/IPsec VPN setup with authentification against a radius server (freeradius2 witch mysql). I would like to have some of my VPN users get a fixed IP address instead of the dynamically assigned IP Pool.
The radius server is returning the correct parameters, I think.
It´s a Cisco 892 Integrated Service Router. Code...
View 2 Replies
View Related
Sep 7, 2011
I'm trying to achieve framed-ip-address/static ip address for some remote access vpn clients and ip allocation from pool dynamically for remaining remote access vpn clients. I've configured my asa [URL].
I'm using local database for user authentication. Remote users can connect and always gets IP address from pool only and never gets the framed-ip I configured for those particular users.
View 3 Replies
View Related
May 30, 2011
I want to configure RBAC for ANM 4,2 using tacacs+ and ACS 5.1 [code]
When the admin user logs in, this policy element is triggerd, but the Role is not sent back.How to configure the Custom Attribute?
View 1 Replies
View Related
Dec 11, 2011
I'm using an ASA version 8.4.2 and a Radius Server.
Is-it possible to configure ASA for sending the name of the connection profile to the Radius Server ?
By default, the radius server doesn't receive this information.
View 1 Replies
View Related
Sep 20, 2011
After trying for several hours to configure ldap attribute to cisco attribute mapping, I found that special characters are not supported by ldap attribute-map at least on 8.4
Here is the problematic configuration:
ldap attribute-map ldap_memberof_map
map-name memberOf Group-Policy
map-value memberOf
[Code].....
View 1 Replies
View Related
Aug 28, 2012
I'm authenticating users against Active Directory and want to also check additionals attributes from LDAP. In ACS 5.3. it was possible to set this up via External Identity Sequence, but in ISE I don't see this possibility. I can set sequence only for authentication, but not for additional attribute retrieval.
When I set a condition in a policy that an LDAP attribute must match with some value, the attribute is not retrieved and autorization ends on default Deny Access.
View 17 Replies
View Related
Jun 28, 2011
We have just set up a Secure ACS 5.2 VM to provide authentication for Anyconnect VPN clients. The clients connect to an ASA 5520, which queries the ACS, which in turn queries Active Directory directly. All seemed to work OK, but I noticed it was using PAP. Following some docs, MS-CHAPv2 was enabled via the "Password-management" command. This broke the configuration and the error on the ACS was:
11309 Incorrect RADIUS MS-CHAP v2 attribute Some references suggest that the ASA and ACS should talk MSCHAPv2 without additional config, so I guess it must be the ASA config for the tunnel-group. There are additional secondary authentication and authorisation pages on ASDM, that I suspect might be necessary to use mschap.
View 1 Replies
View Related
Feb 21, 2005
I'm using Cisco ACS 3.3 for RADIUS. How to do I make Vendor-Specific attribute available? (Attribute number 26, format: OctetString) The online help makes reference to it, but does not tell you how to make it available.
View 9 Replies
View Related
Nov 25, 2012
Is it possible to send profile name as an Radius atribute during client authentication? I would like to match users depends on profile name to sperate Identity Stores in my ACS. ASA 5540 8.4, anyconnect 3.1.01065, ACS 5.1
View 3 Replies
View Related
Oct 2, 2012
I'm in the throes of configuring my 5520 to supply different group policies based on LDAP group membership. I'm finding that no matter what I do only the default group is applied. I'm sure it'll be a simple fix - but I just can't see it. [code]
View 4 Replies
View Related
May 14, 2012
Basically I want to query Radius for AD group membership and apply a set of Bookmarks based on that group. I would use LDAP, but we have two domains and I need both to be available for login, so I am using ACS 5.3 as a proxy. I saw that using attribute 4242 for DAP for group membership, but what is the Group syntax?
View 1 Replies
View Related
May 13, 2013
ACS 5.3 always sends the class=cacs:xyz attribute in an authentication response. How can I suppress that behaviour? The Cisco Email Security Appliance doesn't support multiple class attributes (defect 49096) and even treats guest users as administrators.
View 2 Replies
View Related
Jul 18, 2011
how to add tacacs custom attribute to ACS 4.2 for Nexus 1000V:shell:roles="network-admin admin-vdc"In the interface configuration I've added new service, service - shell, protocol - tacacs+.In the group settings I've enabled this attribute configuration. And it is not works. Default privilege level is assigned to any user with access allowed.
View 8 Replies
View Related
Mar 19, 2012
how I can determine what attribute is coming up as 'invalid' ?Tried full debug and looked at all the logs - nothing.
View 1 Replies
View Related
Nov 9, 2011
We faced with problem after upgrade ASR from 12(2) 33 XNE2. I know that this is an old XE release but our Radius deny authization from ASR with more new XE version. Here is our radius attribute configuretion:
!
radius-server attribute 44 include-in-access-req
radius-server attribute nas-port format d
radius-server host x.x.x.x auth-port 1812 acct-port 1813 non-standard
[Code]....
How can I add in my configuration that ASR send necesserry NAS-Port-Type - VPDN
I couldn't found out any info ((( for radius-server attribute 61 extended
View 1 Replies
View Related
Feb 28, 2012
I am doing 802.1X for a user on Cisco 3650 and wanted the Radius Server to return an attribute to set the Duplex setting of the port. with the correct Radius Return Attribute.
View 4 Replies
View Related
Dec 21, 2012
I have a working ASA 5505 that is used for remote access. It authenticates users via RADIUS (Microsoft AD using two IAS servers), it also authorises users via LDAP and it does some LDAP attribute mapping to get group membership for DAP. This is all working fine however recently I enabled IPv6 to do some testing. I have a /126 subnet on the Inside interface (maps to its equivalent /30 IPv4 subnet) and OSPFv3 running so the ASA has visibility of the internal IPv6 networks. DNS client is enabled in the ASA and all the authentication servers are entered as hostnames. The two RADIUS servers only have A records and the two LDAP servers (Windows DC's) have both A and AAAA records. My plan was to begin test IPv6 on the AnyConnect VPN clients (once I was happy the ASA was working fine with IPv6).
When I initially enabled IPv6 everything continued to work as before, however I had to reboot the ASA today and after it all came back up authorisation stopped working. I did a bit of troubleshooting and the ASA is complaining of not being able to resolve the addresses of the two LDAP servers. From the CLI I can ping the hostnames and the LDAP servers resolve to IPv6 addresses and the RADIUS servers resolve to IPv4 addresses. When I issue the command 'show aaa-server LDAP' (LDAP is the name of the group) I see the servers listed but the address displays 0.0.0.0:
Prior to the reboot both the LDAP servers were showing thier addresses (IPv4) correctly. I can workaround it by disabling IPv6 on the ASA, letting it lookup the (IPv4) addresses of the LDAP servers (so they appear in the 'Server Address:' field above) and then re-enabling IPv6. Strangely deleting and re-adding the servers just with their IPv4 addresses also fails but I haven't fully tested this. I don't know but I think I would have the same behaviour if the RADIUS servers also had AAAA records.
I assume when IPv6 is enabled on the ASA it will perform AAAA lookups as well as A lookups but the LDAP client cannot use IPv6? Just guessing at the moment as I haven't managed to get a LAN capture. [code]
View 1 Replies
View Related
Jun 24, 2011
I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
View 1 Replies
View Related
Feb 9, 2011
SSH is not working in Cisco 7206 VXR Router. I have configure
Hostname
Ip Domain name
Crypto key generate RSA
IN Line VTY 0 4
transport input preferred SHH
transport input telnet SHH
But stll it is not working. I am getting invalid crc recieved in packet.
Current IOS running is 12.3 (19) Enterprise 3des
View 3 Replies
View Related
May 12, 2011
I have two 7206 VXR routers with the VPN Service Adapter either side of a leased line (i.e. no provider between, pure layer two connectivity)A requirement is that traffic traversing the link is encrypted so I've configured an IPSec VPN between the two endpoints.During load testing we noticed a very severe performance hit when the VPN was enabled, disabling it again saw we were able to use almost 100% of the 1000Mbs line. The performance hit looks to be due to the increased MTU size when using IPSec, possible due to fragmentation.
I've read that the 7206 VXR can support 980Mbs (or there abouts) of throughput using AES providing the MTU size is 1400.Configuring this manually on each server in each data centre isn't feasible.As the link is effectively a point to point and we have control over the MTU size between the two routers, what options are available to increase the performance when the VPN is enabled?
View 1 Replies
View Related
Feb 24, 2011
I am having a Cisco 7406 VXR router. I want to know what is the max. MPLS link capacity that can be terminated on the link? We are planning to upgrade the MPLS link to 450 Mb..so was just wondering whether 7206 will support or not..
View 1 Replies
View Related
Mar 9, 2011
I have a problem in understanding how LLQ is implemented in different platforms of Cisco.QoS should kick in only when there is a congestion in the link irrespective of queueing / scheduling (LLQ and CBWFQ).But in certain platforms like GSR and IOS-XR, LLQ is confiugred only with priority and police command not with "prioirity percent <value>" command. In priority and police command since policer is used, LLQ is always on even there is no period of congestion. Of course with police you can re-mark the exceed traffic to different marking but thats not the requirement in my case.
In platforms like 7206, LLQ is configured with "prioirty percent <value>" which works ideally only when there is a period of congestion. When there is no congestion, LLQ class can use scanvenge other classes as well.Would like to know is there any specific reason why there is a difference in the implentation of LLQ between different platforms of Cisco.
View 1 Replies
View Related
Mar 14, 2012
I need to upload IOS c7200-advipservicesk9-mz.124-15.T16.binin 7206 NPE 400 router , As per cisco recommendation router should have DRAM : 256 MB ; Flash : 64I think my router contain only DRAM= 128 MB but not sure.
how much DRAM & Flash it contains.
Router1#sh versionCisco Internetwork Operating System SoftwareIOS (tm) 7200 Software (C7200-IK9S-M), Version 12.3(1a), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2003 by cisco Systems, Inc.Compiled Thu 05-Jun-03 20:58 by dchihImage text-base: 0x60008954, data-base: 0x61E0C000
[Code].....
View 8 Replies
View Related
Mar 9, 2013
I'm getting below error on 7206VXR (NPE-G1) with IOS "c7200-js-mz.124-3i.bin".Attempt to use contiguous buffer as scattered.[code]
View 3 Replies
View Related
Mar 27, 2013
How can I enable Console port in 7206 vxr with NPE-G2 card installed, I need to use console from NPE G2 card.
The device turns on and status is also UP and I can also telnet to the device but I am not able to access the device through console port...
View 1 Replies
View Related
Oct 1, 2012
i did in past a lot of L2TP connection between two end point. in this case ans with 2911 series with ios 15 and DATA license Activated. the l2tp session does not establishe between a this 2911 and 7209. Attached is topology file and bellow the configuration of both router.
PE 2911
l2tp-class l2-dyn
authentication
password 123456
[Code]....
View 1 Replies
View Related
Mar 4, 2012
I have a lot of cisco 7206 vxr deviceses. I have a high cpu problem.I have a 7206 vxr g2. I used to use ebgp for three upstream carrier. I used to bgp full route table method. I have about 800 Mbps active traffics and behing the router about 1600 active customers.
How can I trouble shoot this high cpu problem?
#sh int gigabitEthernet 0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is MV64460 Internal MAC, address is 000c.cf1d.d01b (bia 000c.cf1d.d01b)
Description: ***** GW Interface *****
[Code]....
View 4 Replies
View Related
Apr 24, 2012
In Cisco 7206 VXR (NPE-G2) router , the CPU utilization is at an 80-90% always , but none of the process is consuming not more than 1%. In the show stacks output we are observing network interface interrupt is called very frequently. so what does network interface interrupt is about. Logs for the reference: show process CPU sorted
CPU utilization for five seconds: 88%/88%; one minute: 89%; five minutes: 89%
PID Runtime(uS) Invoked u Secs 5Sec 1Min 5Min TTY Process
1 0 72 0 0.00% 0.00% 0.00% 0 Chunk Manager
2 20020000 17159 1166 0.00% 0.02% 0.01% 0 Load Meter
[Code]...
View 11 Replies
View Related
