In the LAN side configured one Interface VLAN and Configure IP address on that and add the AP’s to the VLAN .. and on the WAN ADSL its p2p with Qtel bridge mode ..
from the Access Point I am able to reach 172.31.30.30 which is the router far interface . BUT still not able to reach the ISP side 172.31.30.29 .
Router Config
no ip routing
bridge irb
bridge 1 protocol ieee
bridge 1 route ip(code)
I'm supposed to configure this 1721 for bridged mode, taking a Level 3 T1 into the serial 0 side and passing it out the f/e 0 side. So, basically that's a T1 to ethernet conversion. I guess this customer is buying a T1 from us but they have to use a different make/model router due to the large hospital requiring that of doctors offices.Encapsulation from Level 3 is ppp static ip address, no password or anything like that.
View 3 Replies View RelatedI recently bought an EA2700 in hopes that it will make my connection faster, stronger signal and stable. However, this is not the case. The connections keeps dropping and the range is the same as my Verizon-FiOS router. Anyway, I'm hoping that a fix be distributed to address this issue. I can't return my router to the vendor anymore.
Now, since I have two routers, I want to be able to leverage EA2700's dual-band feature and the Guest-access feature but I can't make this as a main router since my FiOS router should still be able to supply IP addresses to my cable boxes, thus, I can't configure it as a Bridge. I'm thinking if I just split the IP distribution as follows:
FiOS router: 192.168.1.2-110
EA2700: 192.168.1.111-150
I have 2 Cisco 877 routers and I need one set to bridge mode and one is gateway internet? How do I do?
(LAN)
ADSL <---------------->877 <----------------> 877 Gateway <-----------> Clients
How to set the WNR2000v3 into Bridge Mode. I can not find instructions on it in the user manual or the NetGear website. And Google.com has turned up not valuable results either.
I have the WRN2000v3 plugged into another router via Ethernet. I basically want to "dumb down' the WNR2000v3 into a basic Ethernet switch.
how use wrt54g v3 bridge mode
View 2 Replies View RelatedI’m configuring a Cisco 1142n AP in autonomous mode. The networking part is successfully working, multiple VLANs, SSIDs etc. I would like to configure one of my wireless networks to work with WAP2-PSK and the other with WPA-PSK.I’m confused as to what encryption to set on each radio and the ciphers to use on the SSID for each vlan to enable the best possible security. I’m not using a RADIUS sever in my network .point me in the right direction with the right CLI commands?
View 12 Replies View RelatedCan ASA 5510 be configured as bridge mode and still send Netflow info to a collector?We have a PIX connect internal network to internet. Because PIX does not support NetFlow, as a temporary solution, we were thinking of putting an ASA 5510 between the PIX and internet gateway, and configure it as a bridge so that there will be no routing issues, and the ASA can still send Netflow info to a collector.
View 13 Replies View RelatedIs it possible to put the SRP 527 into Bridge mode to use it just as a modem?
View 6 Replies View RelatedCan ASA 5510 be configured as bridge mode and still send Netflow info to a collector? We have a PIX connect internal network to internet. Because PIX does not support NetFlow, as a temporary solution, we were thinking of putting an ASA 5510 between the PIX and internet gateway, and configure it as a bridge so that there will be no routing issues, and the ASA can still send Netflow info to a collector.
View 1 Replies View RelatedI have a Westell 6100 modem. After my old router, a DIR-655, got zapped by some electric charge from a nearby thunderstorm, I bought a Netgear WNDR3800 router. But I have not been able to get the Netgear router to connect to the Westell 6100 modem reliably [URL]
A friend had given me a Netopia 3347NWG router/modem some time ago but I had never attempted to use it. I was able to get into the web setup screens of the 3347NWG and, without attempting to connect the Netgear router to it, I was able to connect to the Internet via the setup screen. But every attempt to actually go to a web address would fail with a timeout, and efforts to ping always failed with a timeout. Yet the 3347NWG setup said I was connected.
Does anybody know how to setup the 3347NWG so it actually can connect to the Internet correctly so that I am able to surf to a web page or ping an address successfully ?
Does anybody know how to setup the 3347NWG in Bridge mode so that I can use it strictly as a ADSL modem and try to use it with my Netgear WNDR3800 router ?
If I can not use the 3347NWG with my Netgear router I had planned to send the Netgear router back for a replacement since it is not connecting relaibly to my Westell 6100 modem. But if I can get the 3347NWG to work as a modem and reliably connect my Netgear router to it, I will not have to send back the Netgear router for another one.
I have a TWC wideband modem and service. I know that they will enable bridge mode if I ask them. My questions are. After they enable it whats my setup? Do I just run a cable from their modem into a new router that I then set up on my own? Is it that simple?
View 2 Replies View RelatedIs it possible to configure bridge mode in asa 5505 if it is can u provide me a config.
View 1 Replies View RelatedClient has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perform this functions? I will put a Layer 3 switch on both ends to route traffic (3560C-8). Should I use the Yagi antenna's for outdoor use?
View 1 Replies View Relateda customer got an 1552 outdoor AP in local mode and installed it at a building. It has to run as a Mesh AP (MAP). Now the AP connects one time to the WLC 5508 and started a download. After that, the AP never came back. Like we saw on the other installed 1552 RAP's, they all where in local mode.We configured all AP's to bridge mode, but the MAP could not join anymore.Is there a CLI command to change the mode on the AP itself?From the WLC it's not a problem, but for the AP CLI I cannot find sth.
View 1 Replies View RelatedWe have some rolling carts used for telemedicine and are currently using Linksys WET610N wireless bridges. I haven't been very impressed with them - I have to reboot them at least once a week and figure it's a roaming issue. Since they are a residential product they probably weren't designed to do a lot of roaming.I started playing around with WGB and setup an 1142 AP and got it to work. Unfortunately, the only place I can put the AP is inside the cart and the metal top seems to be interfering with the wireless signal.
View 1 Replies View RelatedI'm trying to get confirmation on whether you can have workgroup bridge mode on the 1040 series model.
The 1041N has the same IOS as the 1141/1241 and it has the settings are there, but I read somewhere on the cisco site that workgroup bridge is only supported on 1100 and 1200 series, is this correct or old information?
Scenario is: I have an existing stand alone 1041N AP, on the other side of the building I have a network LAN switch with a couple of PCs, instead of running cables I would like to add an AP as a bridge to link that switch and PCs to the network that the AP is plugged in to. I believe this is called Workgroup Bridge Mode. In fact there already is a cheap non-cisco wireless device doing this but it is unreliable.
I just placed an order for Two 1041N APs, do I need to change the order to Two 1141N instead?
Also even if the 1041N does not support workgroup bridge mode, can it still act as the ROOT Bridge and have 2 1141N APs configured in bridge mode connected to the 1041N?
I have a WLC2504 and 2 LAP1261N (converted from autonomous to lightweight) with release 7.0.116.0 and I want to create a point-to-point mesh link between the 2 APs. When trying to change the APs mode from local to bridge I receive the message "This AP does not support bridge mode" even if the release notes say that mesh is supported on AP1261N. I tried to change the mode from gui and also from CLI.
View 12 Replies View RelatedI have an old computer with dead wifi nc and I thought that bridging it with was121 should work, but can't find anywhere any comprehensive documentation on how to set it up.
View 1 Replies View RelatedDoes ASA supports NAT in bridge mode? especially the 5580 series x??
View 1 Replies View RelatedI am configuring a mobile van that is used for a mobile health clinic to drive to several locations and when pulling into an allocated parking spot the van will connect via wireless automatically. I am using autonomous 1252 AP's and am considering either briding or workgroup bridging.
The issue I am encountering is that the AP inside a van is a router that has to do DHCP across the wireless and because the ethernet interface between router and AP in the van never goes down the router does not know to re-DHCP. I remember from way back there was an IOS command to track a serial interface and drop the ethernet if the serial link goes down. Is there an equivalent command for AP's to drop the ethernet interface if the radio interfaces go down?
I'm using the 2106 in one environment with ROOT AP and MESH AP and when i put these in the Bridge mode, when one client connects to them it isn't working well, sometimes i can reach the client and sometimes not.
I tried it with an Access Point that connect with the ROOT AP or MESH AP and will do an ethernet bridging with another wired client (camera), what happens is very strange because sometimes i can reach the bridge client and sometimes i can reach the Access Point that is doing the bridge. I can't access the two clients at the same time. In this situation i lose the images from camera when i have access to the Access Point and when i get the images from camera i lost access with the Access Point.
When i put the ROOT AP in the H-REAP mode Local Switching with AP 1142 or AP1552, the clients connects well and the bridge mode in the another access point works without problem, when i put the H-REAP in Central Switching i have the same problem.
I'm using in the 2106 WLC the version 7.0.240.0.
I try to change the AP mode of my LWAPP 1242 from local to bridge mode. But when the AP reboots it never associates with the controller, i have to reset it manually.I have the same issue with a LWAPP 1142.I tried to modify the AP mode configuration through the controller CLI but it's the same behaviour, AP never associates.Is there any particular parameter or configuration to perform before changing AP mode?
View 3 Replies View RelatedI want to configure two AP WAP4410N in Bridge Mode and I don´t find the correct configuraction tips.
View 11 Replies View RelatedI have just been escalated to Level 3 support about my bridging issues.Bridge / Repeater mode configuration separated by 150 feet. Worked perfect for over 3 months.Upgraded firmware due to lockups starting to happen, now cant get the bridge / repeater to work longer than 15 min.After MANY support calls, new devices sent (version 2's) still no luck.
Talked to Marcelo at1 866 606 1866 and he stated that the Bridge / Repeater mode will not be supported farther than 50 Feet.(seems like a cop out to me) He didn't seem to have an answer as to why it worked for 3 Months other than interference Of which I have ran spectrum analyzers and see no Interference. **** even 10 feet away I cant get the units to work longer than 15 min.So I definitely think the 50 foot thing is a BS answer.
Also they have told me that External Antennas are not supported with these devices.Again even though People 500 feet away connect just perfect (without a bridge / repeater mode) with 50% coverage!
so here I am (spent 600 bucks) on bricks.. and nobody will support the device and I cant seem to get my money back.I have 8 customers with these devices, I am not going to use Cisco any longer. However will continue to fight this,as we all seem to have the same BS issues.
We have a 6509 with an ACE module. For reasons I don't fully understand the ACE is running using a BVI in bridge mode. It has loads of secondary interfaces.
[Code]...
I can ping all of the IPs on the BVI, but only servers in Subnet 10.7.42/42 can ping out of the the layer 3 on the 6509. I have all the routes configured properly on the 6509 pointing to the ACE for these subnets. The question is though the config has been excepted, is there a limit to the number of secondary on a BVI.
i want the Satellite receiver to be wireless.i have a I-Link 9000 Plus Satellite reciever which has an ethernet port , where the buffalo router will be connected. (Buffalo WHR-HP-G300N Firmware: DD-WRT v24SP2-EU-US My main router is the Linksys Wireless G router WRT54G2 V1.5.
View 2 Replies View RelatedI have an SMCD3GN (from Rogers) that is both a Modem and a Router. I also have a Linksys WRT54G router that I used to use before. The SMC is giving me a lot of problems. The connection is really bad often and my internet speed drops for no reason all of a sudden. I'm getting fed up and want my old router back.
I know it's possible to change the SMC into a modem (put it in bridge mode) and then connect my router and use the Linksys router instead of the SMC. The problem is, I don't know exactly how to set it up and would really like an explanation. I already know how to get into the SMC and Linksys settings as an admin.
How do you set up a linksys routers internet configuration type to public/bridge mode? my model is WRT45g
View 1 Replies View RelatedRegion : Italy
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.20 Build 120705 Rel.39030n Beta
ISP :
I'm facing problem to properly set BRIDGE mode (WDS Bridging). I had a router connected to ADSL line with following setting:
IP 192.168.1.1
Security setting - WPA2/TKIP
DHCP on
The wi-fi coverage is not good in all the floor so I'm trying to extend coverage using a TL-MR3220. I did follow the instruction in this video [url]....
I m setup for my brother's next house. He wants to use to share with my internet access. I do have 2wire modem provider that has wireless capability in my house. So he have DAP-1522 [bridge mode] and adjust in Wireless Setting, to use SSID manual, (Bell9**) WPA. It s successful, and works well. Problem is cannot use wired to computers, blu-ray, Xbox 360 in same time. it will disconnect frequently because in bridge mode doesn't have DHCP reserved?
My bro bought other one is DIR-655. DAP-1522 keep in [bridge mode] to link to DIR-655 (Static IP), and setup DHCP Reserved. He feel relief that works very well and have no problem with any computers and devices doesn't disconnect anymore. my question is why DAP-1522 doesn't have DHCP reserved when bridge mode that connected to any providers modem?
I have a WAG120N. I wish to use it as a modem only and not as a wireless router.I have another wireless router I want to use to handle network connectivity.I want the wag to be set to 10.10.1.1 and I want my router on 10.10.1.2What bridge mode do I set on my wag? Do I need a crossover cable?
View 1 Replies View RelatedI'v just changed my internet provider. That new one uses Annex b, my wag160n is purposed to annex a. Thats what i'v done. Turn on bridge mode turn off dhcp, set PPPoE with my login and password. And here is my problem. I cant connect by wifi with more then 1 device. I can only connect with my laptop when i'm trying to connect on my xbox it says it cannot get ip adress from router. What shoudl i change ?
View 6 Replies View Related