Cisco WAN :: How To Configure Catalyst 2690 Poe
Feb 15, 2011how you configure a Catalyst 2960 series Poe
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2690 / 1811 - Port Flapping With Log DTP-5-Nontrunkporton
Oct 2, 2012I have Cisco 1811 and Cisco 2960 interconnect with each other by TRUNK link. As time pass i recieving below log on cisco 1811 router.
DTP-5-NONTRUNKPORTON: Port Fa8 has become non-trunk
LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne t8, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan100, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan200, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan300, changed state to down
LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan400, changed state to down
Cisco Switching/Routing :: 2690 - SFP Ports On Active And Standby Supervisor Engine
Oct 19, 2012We are expanding out LAN network with more 2960 access switches. All the access switches are suppose to be connected to core switch (4507R) but i have less port on the core switch.
On the core switch we have two supervisor engines (WS-X4515 ---description : "Supervisor IV with 2 1000BaseX GBIC ports"). I can see that on each supervisor engine i have two 1 GB SFP ports available and if i calculate for two supervioser engine i will have 4 1GB ports.
But at particular time only one supervisor engine is active and other is in standby mode (redundancy mode used is SSO between two SUP engines).
Can i used all 4 SFP ports for connecting 4 uplinks to the 4 access switch?Will all the 4 SFP ports active at one time or only 2 SFP ports will be active that is for only active supervisor engine.
Cisco Firewall :: Configure IOS IPS On Catalyst 3560?
Mar 18, 2012is it possible to configure an IOS Firewall IPS on a Catalyst 3560? Which IOS version would I need if it were possible?
View 3 Replies View RelatedCisco WAN :: Configure Catalyst 3560 As Internal Router
Oct 3, 2011I am trying to configure my catalyst swtich as an internal router.
I want to route traffic between 4 different subnets.
192.168.200.0 /24
192.168.201.0 /24
192.168.202.0 /24
10.10.10.0 /24
Cisco Switching/Routing :: Catalyst 2960 - How To Configure With CLI
Sep 20, 2012Will catalyst2960 supports SSH, and how to configures with CLI.
View 2 Replies View RelatedCisco Switching/Routing :: Configure HA Catalyst 4500
May 20, 2012I have two Cisco Catalyst 4507R-E I configure HA. Tips?I plug them in gigabits ethernet?
View 15 Replies View RelatedCisco Infrastructure :: Configure On Catalyst 6509 Two VACL
Feb 10, 2013 I need to configure on a cisco catalyst 6509 two VACL. On cisco 6509 there are already two SPAN ports configured, there are problems configuring other two VACL?
These VACLs send traffic to a Traffic Analyzer (SIEM), there are particular configurations to facilitate the operation?
Cisco Switching/Routing :: Configure The IOS NetFlow 122-58.SE2 In A Catalyst 3560?
Jun 4, 2012It is possible to configure the IOS NetFlow 122-58.SE2 in a Catalyst 3560?
View 5 Replies View RelatedCisco :: Configure Netflow Catalyst 6500 With SUP720-10GE
Jun 5, 2012I tried to configure netflow without success.
Setup is the following.
Cisco Catalyst 6509 with Sup720-10GE IOS 12.2(33)SHX7. There are around 30 L3 vlans configured on the switch. I'm only interested for the traffic on one L3 vlan which is the connection to wan cloud.
I wanna see only the traffic that goes to and come from the wan. On other Catalyst where I have routed interfaces i successfully configured netflow. I read a lot in the forums and documentations but i didn't find the right one.
Cisco Switching/Routing :: How To Configure RSTP On Catalyst 3650 And 2950
Aug 3, 2011Configuring a network with Rapid Spanning Tree Protocol. There's a combination of Cisco 3650s, 2950 and 2960 switches. It is a flat Layer 2 network with a single VLAN. CLI configuration?
View 3 Replies View RelatedCisco Application :: Possible To Modify Configure With Snmp On Ace Module Like Others 6500 Catalyst
Apr 12, 2012Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies View RelatedCisco Switching/Routing :: Configure Inter-vlan On Catalyst 3750
Dec 20, 2012My architecture is the same as show on the link with some difference.I use the router 1841 for inetrnet connexion instead of 7200VXR, this router 1841 is connected on the catalyst 3750 port G1/0/1.I use catalyst 2960 instead of catalyst 2950 or 2948.I use ASA 5510 for conexion on remote branche(I have 5 remote site), This ASA is connected on the catalyst 3750 port G1/0/37
Result of the test:
-I can ping devices in the same Vlans
-I can ping devices in different VLANs
-I can ping all device from the catalyst 3750
I cannot ping the router 1841 or ASA 5510 from the any devices (computer)The gateway of each computer is the correpondant VLAN IP address configured on the catalyst 3750.Why I cannot ping the router 1841 or ASA 5510 from the any devices (computer)
Cisco Switching/Routing :: Catalyst 2960 / Configure Automatically Switch Over DHCP?
Jun 12, 2013I Have a problem I'm trying to configure automatically my switch over ther DHCP when I start the switch it request an IP from the DHCP from here everythings is fine but it does nothing more,indeed I put on my dhcp the option 66 and 67 which is an adress of my TFTP server and a file to download and the switch seems not to understand theses options , I tried my dhcp with a cisco airport and everythings works fine the File from the TFTP is automatically downloaded into the airport...There is an option to add or am I missing something in order to make it work with my switch ?
My switch : Catalyst 2960IOS VER : 12.2(55)SE5
Cisco Switching/Routing :: Configure Virtual Circuits On Layer 2 Switch Catalyst 2950
Feb 14, 2013can i configure virtual circuits on cisco layer 2 switch catalyst 2950 ?
View 1 Replies View RelatedCisco Routing :: Catalyst 6500 / 4500 - Preventative Maintenance On Catalyst Chassis Switches?
Jun 4, 2013Are there any best practices for preventative maintenance on Catalyst Chassis switches. Looking to build a PMI schedule for a customer. Or is there evidence not to perform it at all. Things like re-seating line cards, cleaning fan exhausts, etc.
View 1 Replies View RelatedCisco :: GUI For Catalyst Switches?
May 22, 2012is there any GUI via web (like SDM for routers) to configure catalyst switches(eg 3560 or 3750)?
View 9 Replies View RelatedCisco :: Getting Console Into Catalyst 5505?
Apr 22, 2011Since I am a collector of all things Cisco, I picked up a Catalyst 5505 switch today. It has two supervisor engines in it, a card with 12 fiber ports in it, and two 24 port cards in it. I am trying to console into this thing, but I am not having any luck. I have Googled it and some threads say it uses a normal straight through cable and other threads say it uses the normal Cisco rollover cable. I tried going both routes but no luck?
View 6 Replies View RelatedCisco WAN :: Etherchannel Is Down At Catalyst 6500
Oct 29, 2012I have 2x6500s series catalyst core switch. i configurated vss. all them are working normal. but i have one problem. some of my servers link is down sometimes. I configurated server links as etherchannel.at etherchannel not both of links down only one link down.this modules i used to connect servers to core switch. modules 3 and 7 slot.
View 7 Replies View RelatedCisco :: LMS 4.0 IOS Upgrade For Catalyst 2960?
Feb 16, 2011I tried to update Cisco Catalyst 2960 Switches through LMS 4.0
But LMS won't update the 2960 because there is not enough Flash Space on the device. The 2960 shoud have 32MB but a dir flash shows this
27998208 bytes total (15343104 bytes free)
A manual update on the switch is working perfect. Is this a bug or if there is a workaround to make LMS 4.0 working?
Cisco WAN :: IOS In Catalyst 6500 Is Not Loading?
May 4, 2011Two days ago, a brilliant guy inserted a different ios in a Cisco Catalyst 6500 and erased the original ios. I have twice downloaded the original ios by xmodem (too much time!) and both of them, when I reload the 6500, it doesn't work: I have the following message:
loadprog: bad file magic number: 0x0 boot:cannot load "bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXF11.bin"
Second time, when the ios uploaded, I checked the sup-bootdisk: and the flashboot: and both have the wrong ios listed, but it wasn't there: I've tried to delete it and squeeze it, but had a message saying "can't delete because the ios is not there" or something like this. I finished formatting both (flashboot: and sup-bootdisk:), tftp the ios, double-checked the bootloader, compared with other identical 6500 and reloaded again, just to find the same message I've written before.
Supervisor 720 PFC3B. Slots for disk0 and disk1 are broken or I can't read them from the rommon.
Cisco WAN :: How Many Catalyst 4500Xs Can Be Stacked Together
May 12, 2013I'm designing a hierarchical 3 layer campus network with different switch blocks .We need 10Giga Ethernet in the core to distributions and access layer , I was thinking about using a pair of catalyst 4509E in each block.after that I got interested in 4500Xs , in comparison with 4509Es they are much thinner and saves more room in rack space .I wanna use 4500X in my distribution layer .
The question is , as you know 4500Xs have 40 10Giga Ethernet ports , in some of my switch blocks I have more than 40 access switches (40 uplikns to distribution ) i wanna know how many of 4500Xs can i stack together ?
Cisco :: Catalyst C3750 Can't Get MIB CdpInterfaceExtTable
May 9, 2013Why I can't get the "cdpInterfaceExtTable" by SNMP ? The other CDP info are correct, only this table is empty.
I found the configuration method in CLI:
interface GigabitEthernet3/0/13
switchport priority extend cos 5
interface GigabitEthernet3/0/14
switchport priority extend cos 5
But I still can't get anything back when I walk this node,
Cisco :: Catalyst 6500 - Cannot Login Using GUI
Jun 21, 2012We are facing an issue with the NAM3.Version: 5.1(2-patch4)
we can not login using the GUI. when we try to login we are getting the following warning:
Initializing database. Please wait until initialization process finishes.(see attachment)
we have rebooted the NAM3 module but the issue is not solved. the NAM3 module is running on 6500 Series Switch.(Cisco Catalyst 6500 Series Network Analysis Module (NAM-3)
Cisco WAN :: Configuring NAT On Catalyst 2960
Jan 4, 2011I've just made a purchase for a Cisco 2960 8 port switch ( Exact model: WS-C2960PD-8TT-L ), I reckon this is what I need to set up my network, so far I've gone through the Express Set-up and configured it through there with no problems. I've set up the hardware in the following manner:
-Internet Modem
>Port 8 on Switch
->Port 1 on Switch goes to 1252 Cisco AP
->Port 2 on Switch goes to Linksys VOIP home Router
I let it start up and can connect to the internet through the AP, and through the router. (I'm posting through the AP-Switch set-up right now.) However, once I connect to the AP with a second client. It refuses to let the second client connect/not give an internet connection, as it would a direct connection to the modem.I'm going to assume this is due to NAT not being configured through the command line on the switch yet.
Cisco WAN :: Manage Catalyst 2960 With CNA
Jan 23, 2011i have got 5 catalyst :
Cisco Catalyst WS-C2960G-24TS-S
version 12.2 (53) SE
Image : C2960S-UNIVERSALK9-M
and i can 't configure the switch with Cisco Network Assistant. I have got this error : "unsupported device".
it is not possible to configure this model with CNA ?
Cisco WAN :: Does Catalyst 4900m Support IP-SLA
Oct 30, 2011Catalyst 4900m does not support command "ip sla <entry-number>" like Catalyst 6500. If 4900 does support SLA, how to configure it then? [code]
View 4 Replies View RelatedCisco :: How To Upgrade IOS Catalyst 3560
May 1, 2012I want to upgrade a Catalyst 3560-48PS to the last IOS.I get an errormessage stating that there is insufficient space in flash: I have deleted all files in flash - but I still get the same error message. According to the documentation there should be enough memory. Messages are pasted below:
Switch#dir
Directory of flash:/
No files in directory
15998976 bytes total (15997952 bytes free)
Switch#archive download-sw tftp://192.168.9.13/c3560-ipservicesk9-tar.122-55.SE.tar
Loading c3560-ipservicesk9-tar.122-55.SE.tar from 192.168.9.13 (via Vlan9): !!!!!!!
[OK - 15964160 bytes]
Loading c3560-ipservicesk9-tar.122-55.SE.tar from 192.168.9.13 (via Vlan9): !!!!!!!!
examining image...
extracting info (109 bytes)
[code]....
Error: There is insufficient space in flash: to install the required
Error: image. Clean up some old images, and try again.
Cisco :: Directing Traffic Through Catalyst 2940
Aug 2, 2012I have a Cisco Catalyst 2940 switch, eight ports. Ports 1-4 are connected to a media converter A. Ports 5-6 and 7-8 goes to two separate servers, B and C. Let's say I want traffic from B->5->1->A then through some equipment (which just pushes the data) and back through A->2->6->C without the data just recognizing a shorter path B->5->6->C and thereby skipping the equipment in between. Is this possible without a router? Ridiculous set-up? Yes, though the switch is the only means I have to connect to the media converter in this case.
View 5 Replies View RelatedCisco Catalyst Interoperability With Brocade ICX Switches
Feb 12, 2013At the moment our whole company is equipped with Catalyst switches ranging from 2950, 2960 to some 3560G and 3750X (Cores). Now I'm thinking of replacing some of the old 2950s (which are only fast ethernet) with some Brocade 6430 or 6450s, since they're so much less in pricing.My concerns though are: will spanning tree work problem free, access lists still work and any other problems I could encounter with interoperability.According to Brocade most of these things should work fine, but I'm searching for some facts from people who are running a heterogenic Network with these two brands (even the same product lines).
View 4 Replies View RelatedCisco :: Best GBIC For Connecting Two Catalyst 2948Gs?
Apr 18, 2012I am going to connect two Catalyst 2948G switches, and I want to know what the best GBIC is to use to do so. A link to a cable I could order would be great, or a brand and model number.
View 3 Replies View RelatedCisco :: 2960S Catalyst Access Switch From VPN
Dec 10, 2012I have a 2960S Catalyst switch in my LAN, with the firewall and the servers in the same VLAN (vlan 3).All the servers and the firewall are in the vlan 3 are in the "192.168.19.0/24" subnet, the firewall has the IP "192.168.19.1".I can land on the firewall with a VPN (192.168.130.0/24) which has a complete view on the subnet 19/24.I can access, manage and get SNMP information of the Catalyst from the servers but I can't do the same from the VPN.Is there some feature I need to enable on the switch in order to allow 192.168.130.0/24 to access it?
View 4 Replies View RelatedCisco WAN :: Minimize The Buffers On Catalyst WS-C3550-12T
Feb 8, 2012Howto minimize the buffers on Catalyst WS-C3550-12T to absorb 50ms to 100ms of PCoIP traffic according to:
[URL]