Cisco WAN :: Setup The 3G On 819 Router?
Dec 4, 2012I acquired an 819 router with a integrated HSPA+R7 modem, does anyone setup the 3G internet option with this modem? My 3G ISP is Telcel.
View 6 RepliesI acquired an 819 router with a integrated HSPA+R7 modem, does anyone setup the 3G internet option with this modem? My 3G ISP is Telcel.
View 6 RepliesIs there a way to set up Quick VPN on the RV120W without changing the internal subnet? I have just taken over responsibility for a network and I don't know all of the nooks and crannies yet, so I'd rather not change the internal sub net. I've tried setting up a user then changing the LAN settings afterward, but it automatically removed the VPN user when I did so.
View 1 Replies View RelatedI've just purchased a couple of SRP527W routers. I've been unable to even browse to the default 192.168.15.1 to start my configuration. My local network is 192.168.1.x. At risk of showing my stupidity, what am I doing wrong.
View 5 Replies View RelatedI just got E1000 cisco wireless router. Started setup, everything worked fine and replaced admin password with my own. For some reason got error message. tried to redo setup and got message router not recognized. used laptop and found out that wireless works fine. After few days noticed that there is a (mynetworkname) guest connection you can connect without any password. i don't need that stupid thing and my question is how to disable guest network? I cannot reach Main Menu from cd and have no idea where to look for it when i connect to router by web.
View 9 Replies View RelatedWhen I type the routers IP address in teh brower window, nothing happens so I cannot access the router setup. I have a WRT110. What am I missing. I was able to do that when I first setup the router.
View 9 Replies View RelatedI am now confused whether SSL VPN can be set up on Cisco 881/K9 router.If yes, for just 5 users, do I need to buy the license or license is bundled with the router?
View 2 Replies View Relatedtypical ADSL configuration. My ISP only sends out DNS information automatically (PPP) - no static entries. I need to capture this information and relay it to users via DHCP. Currently when I do "ipconfig/ all" all DNS entries are empty.
View 6 Replies View RelatedWe have a location that currently has one frame T1 and 4 point-to-point T1s. We are looking at adding a second frame T1 to be bonded with the first. Currently, we have an old 3640 router, so I am thinking this would be a good time for an upgrade. Cost is a concern, so I am hoping to buy something refurbished that is newer than what we have now but is not going to cost a ton as buying new would. My thought is either a 2821 or 2921 with 2 HWIC-4T1/E1. I am not familiar with this HWIC just wanting to make sure this a good solution for our situation.
View 8 Replies View Relatedhow to setup natting on a 3925 router.
View 1 Replies View RelatedWe purchased this router with the cisco IOS software installed. I've installed the Vista driver on my win 7 box. I believe that should work. I installed Putty to termainl in and I'm using a USB connection. I cannot even log into the router. I thought I was going to see some kind of setup wizard using the CISCO software so I would use a GUI and get things moving. I've got loads of reference material with command etc. but I just can't connect to the router to make it happen.
View 3 Replies View RelatedI have a router 819 with 3G built-in. Are there any manual for how to setup the interface celluar 0 for this router out there? I have Verizon as my 3G provider.
View 4 Replies View RelatedI have a bit of an issue setting up an Cisco 837/SOHO ADSL Router.
Basically what it is is that my Broadband router isnt doing its job very well, and the last piece of the puzzle in the server area is to upgrade the router, and I have with this. Now. I hve followed the setups as per cisco's guidlines very well and doen alot of research on the CLI commands, I have access to the router and have setup the system.
My broadband in the office is Orange/EE and its PPPoA. I hvae all the settings, and such and have followed a set of commands that apply to BT broadband but, It simply hasnt worked in my case. Any CLI commands to setup this router so i'll replace my business livebox.
I am pretty new to the configuration of a DMZ and I have the task of setting one up.I have a Cisco 2811 Router running Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3), 2 FE interfaces.One FE is connected to the WAN, with a loop back interface configured with the public IP for Internet access in the office.The other FE has 2 sub interfaces configured, one for data and the other for voice traffic.Users within the office are configured to use the data VLAN to access the internet through the WAN.
Now we are setting up some new services and we require to have DMZs setup.I want to setup 3 zones now that the different servers would reside in. How can i achieve this using the existing infrastructure I have?I have an idea to create more subinterfaces and assign them to the zones, but I am still not sure how this would play out. I have been on this for the whole day and unable to make significant progress.
I just purchased thie Cisco 2921 router and have all the configuration completed except the Firewall and NAT. We have 4 supnets at our location on the router each with a DHCP handed from the router to our network. Any examples for the Firewall and Nat configurations?
View 6 Replies View RelatedI have reset the router of Cisco 870. I need to connect the router for ADSL connection but don't know how to do it.
[code]...
I've got working PAT, but absolutely not sure how to perform additional task.
ip cef
no ip bootp server
no ipv6 cef
interface FastEthernet8
ip address 192.168.1.141 255.255.255.0
duplex auto
speed auto
[Code] ........
I have an ASA 5505 with a dynamic IP address from the ISP.What I need to accomplish is the following:
- Either setup that ASA (Dynamic IP)VPN with an IOS router (Static IP)
- Or setup that ASA (Dynamic IP) with another ASA (Static IP)
i am using cisco 2821 router at the edge in my network where the WAN link is terminated.i want to configure Redundancy . So will 2821 support ? If yes what is the another router .Is it the same series or different for redundant configuration.
View 2 Replies View RelatedI'm trying to setup Cisco 887g-w router with 3G GSM SIM card. We got a data sim card from telco with a static IP address. Below is the some outputs. The cellular interface keeps flapping, but am not able to ping at all to any public IP address and it's not connected.
International Mobile Subscriber Identity (IMSI) = 525016180934095
International Mobile Equipment Identity (IMEI) = 353223040059355
Integrated Circuit Card ID (ICCID) = 8965011104140220958
Mobile Subscriber International Subscriber
[code]....
I am attempting to setup a network containing two routers, a primary giving me ADSL internet access (a 3com 3CRWDR101A-75) and a secondary router that has VPN (Cisco WRV210).
The primary router has the following LAN settings: 192.168.0.1 / 255.255.255.0 with DHCP enabled. WRV210 has the following LAN settings: 192.168.1.1 / 255.255.255.0 with DHCP enabled. Cable connection is from LAN port of first router to Internet port on second router. In this way, I'm able to get internet browsing on 2 laptops connected to WRV210 I have also a Panasonic IP PBX connected on the second LAN (the WRV210)
I need to setup the VPN on WRV210 to be able to get SIP calls from outside of the local networks (through internet). As I am a novice in networking, both routers are on DEFAULT setting.
I have learned a lot during the last 7 days to be able to understand the networking concepts but failed to setup the correct configuration.
For example if I change WRV210 from gateway mode to Router mode, I will not able to browse the internet despite the Help file that says "Select the mode in which this Router will function. If this Router is hosting your networks connection to the Internet, select Gateway. If another Router exists on your network, select Router. When Router is chosen, Dynamic Routing will be enabled"
Also i am able to ping the first LAN 192.168.0.x from WRV210 but not on the other side (from primary router to WRV210).
I am confused to use and combine different settings (NAT, Routing, Ports, ...)
Cannot setup NAT on edimax router
[URL]
It works well - I can connect from TESTPC and LAPTOP (bottom left corner) to SERVERS A/B/C (bottom right corner) without any problem. Everything seems to be routed perfectly, however from SERVERS A/B/C I cannot ping TESTPC and LAPTOP, and I can't even establish an RDP connection.
I was told to setup static routes or NAT, but I am at a loss on how to do it. I am using an EDIMAX BR-6424NL wireless router
I just bought a new wireless router and I currently using my older dlink di-524 wireless router in my home. Reason in buying a new one is because currently the dlink router is in the family room use to be a garage and my wifes imac is in our bedroom the couple rooms down not next door or anything, and the imac and even our smartphones when in our beedroom the connection gets disconnected then reconnected etc etc, basically signal strenth is low intialy when connected to the router.
View 1 Replies View RelatedOkay, so one day I went into my router setup by typing in the router address and I clicked a few things and did some stupid things just to mess around with it, I reset to default and exited. The next day I try do it again and I can't get to the router login page because it says it cannot connect to my ip address. I tried reseting the router by pressing a the button and it doesn't work after I try a few times
View 7 Replies View RelatedMy company is setting up a small branch in Scotland (the main office is in Bristol)All we need one desktop, one laptop, a printer and we will be using a DraytekVgn router, and a small switch.We need VPN to this office to set up an inhouse application.How would I set this up with minimal configuration.......ie...Does BT send a router/modem with the set up..Is there anything inside the router configuration that has to be changed.(I know PPTP etc has to be enabled).Do I use the same vpn external ip address we use for our other 2 branches....Can I change the IP Address of the router from 192.168.1.1........to say 192.168.100.1.
View 6 Replies View RelatedI want to set up 2 separate network with one cable modem for my restaurant. we wants to provide WIFI access to its customers, but wants to keep their internal network separated.
View 2 Replies View RelatedI just switched to DSL from cable internet and am having some trouble setting up my router with the new internet service. DSL modem-->Router-->Network with PC and PS3
ISP is ATT
DSL modem is a TP-Link 8616
Router is a D-Link DIR-628
I put my ATT username and password into the router but it never completes a connection to the internet. I was able to create a soft PPPoE gateway connection through my computer using my username and password, but I want my router to do this, not my PC. How do I get my router to connect directly to the Internet connection rather than having my PC connect? My setup would be fine as-is if I just had 1 computer but I also want to go online with my PS3, and it won't connect like my PC will, even after putting the username/password in.
I am tryign to setup 2 networks for my company. I need 1 network for the first room and another network on the second room. Each room can't access another room's computer. I have setup 2 workgroups for each room but it seems that the workgroup can't setup passwords. Every computer is in the same subnet with static ip. They all connect to a switch -> router -> modem.
View 3 Replies View RelatedI brought a router TP-LINK TL-WR741ND . I have an usb modem which has no other port as lan . I have only one ethernet lan controller which is integrated .Now With the mentioned device above can i setup my router , so i can use the internet on other wifi device.
View 2 Replies View RelatedTrying to work out if I can setup a VLAN interface on a 1721 router.The only interfaces that are listed are the Ethernet (W1-ENET) and the Fast Ethernet interface.I'm still super new to all of this and learn how to change IOS via rommon and TFTP after realizing I had an IOS too large for the memory?
View 3 Replies View RelatedSo I just setup a new router and got everything up and running...I got every wifi device connected, my iphone, ps3, laptop..except one laptop.Its a Windows Vista laptop, I can connect to the network but I cant receive bytes or load web pages. I can connect to the network but not the World, its blocked by an X...I dont know if vista laptop has the same ip as another device.. Cisco E1000
View 14 Replies View RelatedHow do I setup Vizio blue ray with Cisco wireless router
View 1 Replies View RelatedI have been given a task, where I need to create a failover setup from a 1800 Cisco router to a LAN network 2 hobs away (see topology).The reason I have been given this task is because the wireless links are not so realiably, but necessary.I'm thinking of doing this failover task with IP SLA on the routers fiber 1 and fiber 2 link, so when/if one off the links goes down, it instantly chooses the other link.I have also been thinking about implementing STP instead, and replace the router with a switch, but i'm not sure exactly how to implement it. Unfortunately I'm not able to test anything, as we are still waiting for the fiber lines, but I want to be prepared as much as possible.
View 5 Replies View RelatedI got connected ASA ----- ROUTER 2811) to metroethernet switch from my ISP , with a 4MB of bandwidth but the internet connections to all my LAN has been frozen and we lost connection to the internet, to restart the internet service I need to boot the ROUTER 2811 - and ISP switch to rollback the internet operation,My ISP support tell me if is possible to set up the traffic bandwidth in one or both borders devices, ( ASA 5510 or ROUTER 2811)
View 3 Replies View Related