Cisco WAN :: Setup 887g-w Router With 3G GSM SIM Card?
Jun 23, 2011
I'm trying to setup Cisco 887g-w router with 3G GSM SIM card. We got a data sim card from telco with a static IP address. Below is the some outputs. The cellular interface keeps flapping, but am not able to ping at all to any public IP address and it's not connected.
International Mobile Subscriber Identity (IMSI) = 525016180934095
International Mobile Equipment Identity (IMEI) = 353223040059355
Integrated Circuit Card ID (ICCID) = 8965011104140220958
Mobile Subscriber International Subscriber
[code]....
View 4 Replies
ADVERTISEMENT
Jun 23, 2011
I have one problem regarding a configuration (or setting up) of 3G SIM card for 887G router backup. That SIM card had a PIN code, so I disabled it, and now I can see that 3G light flashes Blue, so it detects 3G network. Also I can see that modem tries to dial up to connect to network, but with no luck. It has CHAP APN. Also in configuration I've found that there is PPP CHAP username and password, but I don't have any of those. I've tried to configure my SIM card with Username and Password, but it doesn't save. At the moment I have: Cellular 0 is down, line protocol is down. Dialer 2 is up (spoofing), line protocol is up (spoofing).
SIM card status is OK. Network detects O2 - IRL - yes.
It detects the network, but cannot connect to it. I'm not sure how to setup the SIM card or how to unlock it.
View 3 Replies
View Related
Feb 27, 2012
I have tried pressing the Reset button (within 5 secs) when the router power up. On my HyperTerminal, the image was loaded and the line interfaces were up. But when I press enter on HyperTerminal, there was no response.
View 1 Replies
View Related
Feb 11, 2011
I need to setup my LAN card to access 2 gateways.
OS: winXP sp3
IP: 192.168.1.101
One gateway is 192.168.1.254 to the internet.Another gateway is 192.168.1.253 to access (via VPN) the other subnets 192.168.x.x? I can even install a second lan card.
View 4 Replies
View Related
Oct 8, 2011
how can i share my Internet connection using 2 LAN card without router to my another pc
View 1 Replies
View Related
May 22, 2012
I got a different tower to use ,and added my wireless card and external antenna to it , but need setting up the new PC tower to use the wireless card and antenna. How to set up the available connections so that I can use this in my garage too.
View 1 Replies
View Related
Aug 16, 2011
First network card have the static IP address 82.x.x.30 from the ISP.The second network card have 2 IP addresses: 192.x.x.0 and 82.x.x.1 ( first IP is for LAN and second IP is for routing the additional IP class).In other words if i have the computer "Z" with configuration: IP: 82.x.x.100 Sub: 255.255.255.128 and GTW:82.x.x.1 i can access the internet but practically with with the IP from ISP wich is 82.x.x.30
View 1 Replies
View Related
Apr 20, 2012
I think I am having problem with my network card I am running windows 7 with Dell wireless 1390 WLAN Mini-Card lots of times the signal is low and I get the error message no internet connectivity or some other error message that I am not being able to connect to the network provided by my wimax modem, Is there any program that I can download to test if there are any errors related to the network card or any way to fix this?
View 3 Replies
View Related
Jan 2, 2013
New computer has a LAN 802.11n card. What router should I use to interface?
View 3 Replies
View Related
Dec 21, 2011
How to add a wic-2t card on router 2800
Had the card as follows
I want to know routr 2880, such as the following picture
View 1 Replies
View Related
Jun 14, 2012
recently signed up with comcast and everything was working well the first day or so. My download speed has since crashed and burned, getting .3-.5 Mbps down but still normal ~4Mbps upload speed. A wired setup through the router gets ~22Mbps, which is what I'm paying for so it's not an ISP issue. how I can figure out if it's the router's wireless or my laptop's card (no other PC handy) and what I can do to fix it.
[code]...
View 4 Replies
View Related
Nov 25, 2011
I have not internet in my area ( rural ). I currently use Hughes net ( Poor )I just bought and loaded software for a verzon modem card.How to I hook up a router to the system?
View 2 Replies
View Related
Oct 20, 2011
I have a VIC 2Fxs card and it is not getting recognized in the 2811 router. I checked the cisco website and I saw that the FXS card for the 2811 is a VIC2-2FXS. If i were use this, do I insert it in the HWIC port or do I use a Voice 2V module to insert the FXS card and then insert it into the router. Also , is there any other FXS card that can be used apart from the VIC2-2FXS.
View 1 Replies
View Related
Mar 7, 2011
I have a 2801 router with a HWIC-3G-cdma card that I have inherited from a predicessor. How to use a cellular card on a router and need to get this thing up and running. Any example config that I can see or point me in the right dorection to get this up and running? I have the cellular card set up as Cellular0/1/0 on the interface, I assume that that was done by default, and it has an IP address. The Static Route of 0.0.0.0 0.0.0.0 Cellular0/1/0, in the config with only 2 other interfaces as being direct connection. But that is as far as I recognize. Do I need to set up a router protocol? Which one? How do I use the cellular card? Do I need to have an ISP connection?
View 1 Replies
View Related
Sep 12, 2012
One of my customer is looking for 1 port OC3 card for 7200 series router. There are two options (PA-POS-2OC3/PA-A6-OC3)However my customer is not sure whether he wants a ATM/POS card.
How to determine whether i should go for ATM or POS Card for OC3. Or atleast what should be my approach to determine whether i should go for ATM or POS Card for OC3.
View 4 Replies
View Related
May 8, 2011
Wireless card not connecting to router .This is what we have so far
[code]...
This issue seemed to be addressed previously, but wasnt sure if I should create a new thread or reply to the old one.
View 10 Replies
View Related
Mar 30, 2011
Have Dell 6400, run Win XP serv. pack 3. No red X or yellow ! under Device Manager. I did open up laptop, took out WLAN card, restarted laptop, turned off laptop, reinstalled WLAN card, restarted laptop.
[code]...
View 14 Replies
View Related
Sep 8, 2012
When I use my USB modem card directly connected to my computer it is much faster than when I connect it via my wireless router.
Why? How do I increase the speed via the router?
View 1 Replies
View Related
Oct 2, 2011
I just got a brand new Cisco 2951 router that has built-in 3 gigabit interfaces cards. We want to add additonal 2 GE EHWIC-1GE-SFP-CU card to it. When it booted up and type show inventory, it did not detect the presence of the card. There was light on at the back of it. I have checked the compatibility on Cisco. The card is compatible with this router. Do we have to install the card with special instructions in order for the router to see it?
View 1 Replies
View Related
May 19, 2011
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
View 1 Replies
View Related
May 10, 2011
I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
View 2 Replies
View Related
Feb 14, 2012
I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?
View 1 Replies
View Related
May 29, 2011
We have a cisco 3825 router with OS version 12.4 and one VWIC2-2MFT-T1/E1 card at Slot 0. Now I have to add one more card of the same type in the router.
I need to know the steps or process to add the the 2nd card in the router.
View 10 Replies
View Related
Feb 25, 2011
I have cisco 1721 router so I installed an ethernet interface card so when I make show run I found that there is a fast ethernet 0 and ethernet 0 (which I installed) so i wand to make subinfaces of the etheernet 0 but I can't. I tried to make encapsulation dot.1q but it doesn't accept it.
Is Ethernet0 supported to generate subinterfaces?
View 3 Replies
View Related
Feb 19, 2013
Is it possible to connect wifi router to data card?
View 1 Replies
View Related
Jul 12, 2012
how to get my driver back, D-Link wireless router NIC card driver, i formatted it yesterday because of viruses, but since then i cannot have internet unless the driver is fix back
View 1 Replies
View Related
Aug 14, 2012
My PC has a wieless card in it and last night the internet went off and then I wouldn't find my router at all, just everyone elses.I tried resetting the router, unplugging it an leaving it for a while, then resetting my PC. Tried unplugging the wireless card and plugging back in. Made sure I have latest drivers. Disabled and enable the card.I then tried plugging in an external belkin adapter in the usb and that worked.There are 2 other PC's in the house and they are both connecting to the internet fine. But I tested an old laptop we have and that didn't pick up the router either.I went on the pc in the other room next to mine and tried changing the channel it was on from 12 to 5 and it actually worked now my pc can find my router (???)But we've been having alot of issues lately with bad internet on certain channels etc.I don't really understand why channel 5 would work but channel 12 doesnt? We are experiencing more latency on that channel too.
View 1 Replies
View Related
Mar 5, 2011
I have a laptop using a wireless Ralink USB card to connect to the internet. Is it possible to use the unoccupied Ethernet cable slot to hardwire into a router and use the router to send out the wireless signal picked up by the USB card to other devices?I know I shared my connection like this to my xbox 360 but wasn't sure if it could be used with a router.
View 1 Replies
View Related
Mar 3, 2013
My wireless router is a cisco linksys e3000, and I was wondering what the best wireless desktop card would be?
[code]...
View 2 Replies
View Related
Jun 6, 2011
have remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
View 5 Replies
View Related
Sep 2, 2011
How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies
View Related
Jul 13, 2011
I recently installed a WIC 1DSU-T1-V2 card into a 1841 router to add to a multilink bundle. I inserted it in Slot 1 and powered up the router and there was a new serial interface showing in the config automatically as s0/1/0. I was able to get it setup with ppp multilink and added to the multilink group. The problem is I need to do a sh controller or sh service-module to see if there are errors happening (I'm using this card as a replacement for an interface that was giving errors with this line before). I can do a sh s0/1/0 and that works but I can't see deeper. I found it odd that the serial port just appeared in the config when I booted without having to do anything, if this is correct behavior and how I see the Controller or CSU info for troubleshooting?
View 1 Replies
View Related
May 5, 2011
I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 Replies
View Related
