I need to setup my LAN card to access 2 gateways.
OS: winXP sp3
IP: 192.168.1.101
One gateway is 192.168.1.254 to the internet.Another gateway is 192.168.1.253 to access (via VPN) the other subnets 192.168.x.x? I can even install a second lan card.
how can i share my Internet connection using 2 LAN card without router to my another pc
View 1 Replies View RelatedI'm trying to setup Cisco 887g-w router with 3G GSM SIM card. We got a data sim card from telco with a static IP address. Below is the some outputs. The cellular interface keeps flapping, but am not able to ping at all to any public IP address and it's not connected.
International Mobile Subscriber Identity (IMSI) = 525016180934095
International Mobile Equipment Identity (IMEI) = 353223040059355
Integrated Circuit Card ID (ICCID) = 8965011104140220958
Mobile Subscriber International Subscriber
[code]....
I got a different tower to use ,and added my wireless card and external antenna to it , but need setting up the new PC tower to use the wireless card and antenna. How to set up the available connections so that I can use this in my garage too.
View 1 Replies View RelatedFirst network card have the static IP address 82.x.x.30 from the ISP.The second network card have 2 IP addresses: 192.x.x.0 and 82.x.x.1 ( first IP is for LAN and second IP is for routing the additional IP class).In other words if i have the computer "Z" with configuration: IP: 82.x.x.100 Sub: 255.255.255.128 and GTW:82.x.x.1 i can access the internet but practically with with the IP from ISP wich is 82.x.x.30
View 1 Replies View RelatedI have a milestone VMS (video management system) server running on a customers site. The server has two network cards. eth0 has a static IP 10.0.15.250, mask 255.255.255.0, gateway 10.0.15.254 (the gateway is a firewall connected to the internet via an eircom modem in bridged mode) eth1 has a static IP 10.94.238.2, mask 255.255.0.0 gateway all the cameras and related equipment are in the range 10.94.238.1 ~ 20 Customers network users what to view the VMS via an application which needs to run on their PC and connect to the VMS server on 10.94.238.2, The customer has given me a gateway address of 10.94.200.1. However when I use this gateway address in the default gateway of eth1 I loose internet access on the server because the server can not resolve the DNS address. The cusotmers users can see the VMS and the monitoring station can see the VMS via a VPN. However I need internet access otherwise Teamviewer will not work and I can not access the server for configuration and maintenance remotely. Is there some other way I can implant the customers gateway so they have access but I still have internet on the server.
View 2 Replies View RelatedI have two network cards in my computer, one is connected to the ADSL router for a BSNL broadband connection and the other is connected to our compay's MPLS network on which our core software is run , now both networks have different gateways through which they connect , the bsnl ADSL router gets its ip from DHCP ,our MPLS network has its own network ip schema.The problem is I am not able to use both connections simultaneously, if I have to work on our software I have to switch off the ADSL router and if I want to surf the internet then I cannot work on our softwware.
View 3 Replies View RelatedI've got a network with the following address and subnet mask:
xxx.17.0.0
255.255.0.0
The original gateway that we had on the network is at:
xxx.17.0.254
This gateway is a Netgear VPN firewall and it also has a bit of port forwarding going on to a couple of servers on the network.We've now had a new line put in and we have to use different hardware on that line so in order to phase that in, I've set this up as a new gateway at:
xxx.17.1.254
Internally, the clients and servers are quite happy with this and will happily use the new line.Problem arises when users connect via VPN to the OLD gateway (I haven't got VPN set up on the new one yet). Users can still connect to the VPN but can't see any machine that is using the new gateway.How can I get around that? Does the old gateway need a static route?
I have a scenario which i would like to discuss with you people. I have a branch office connected with the Head office using wireless radio bridge(point to point connectivity). Here is the configuration at branch office.Things are working fine until now. The branch office has a DSL internet connection and required to be shared among the users. option 1 (problem)DSL terminate on swtich and all clients have a DSL modem as their default gateway and ISP's DNS. Internet works fine but here comes the problem, now they lost the connectivity with head office.Now my question is i cant have two default gateways then what should i do?
I bought dlink dir615 router and want to configure in such a way that internet terminate on dir 615 and branch office pc's should be able to use the internet as well as get connected with the head office with default gateway configuration.
We our currently using site-to-site VPN tunnels to connect our multiple offices using static public IP's via ADSL connections.We wanted to get an additional ADSL connection from a different ISP so that if one connection drops, the other could be used.Are there any hardware devices or tricks we can use to automatically get our networks to failover to use the backup ADSL connection and have our VPN traffic remain up?
View 1 Replies View RelatedI installed m0n0wall in a virtualized environment, i have 10 PCs connected to a router ( 192.168.1.0/24) which connect them to the internet through PPPoE, the problem is that this router does not have a QoS so what i want to do is the following :-
let all the PCs get their IP from the Router and the default gateway will be m0n0wall
the moon wall will have 2 interface (Lan 192.168.1.20) and (Wan 192.168.1.21 and default gateway 192.168.1.1)
now when any PC want to access the internet it should go through m0n0wall and then m0n0wall will forward the connection to the default gateway through the wan interface which is the PPPoE running on the router (192.168.1.1)
I have two different networks on same LAN.One net has public 2xx.x.x.x IPs (some on DMZ, they are servers with their own internal firewalling) and goes through a GBeth switch to a Cisco 25xx router for accessing HDSL modem with several HDSL trunks and then Internet. That router is configured to let external IPs access only DMZ IPs, of course.The other net has 192.168.x.x IPs and goes through another GBeth switch to a DLink router to access ADSL. Mainly for download traffic at a low flat cost.I would like to have a way to let the 192.x.x.x machines access the servers on the DMZ of the 2xx.x.x.x net without going outside the physical LAN. The servers host mail services and so sending heavy attached documents needs a hi-speed LAN connection and certainly not the ADSL upload capability. Not to say about servers web contents maintenance.
View 1 Replies View RelatedI have LinkSys WAG160N V2 with the last firmware 2.00.20 I have very annoying issue, the Gateway always disconnected from time to time .. Some days it work so fine and some days it disconnect 20 times per day and I have every time to go Status >> Gateway and press connect , another weird thing is that sometimes it gaves me speed 3784 Kbps and sometimes 3500 Kbps , sometimes it gaves me the right speed 4700 Kbps i did think maybe it's my ISP problem , but after the upgrade the problem gone for 3 weeks then it back again, and when it back I did make factory reset and reconfigure it again regarding my ISP settings and it did work fine with 3784 Kbps speed and it should be 4700 Kbps.
View 9 Replies View RelatedI need to route a subnet from a 7204 to 2 different gateway's which are not Cisco based. I cannot use HSRP, GLBP or VRRP as the other 2 gateways don't support theses protocols. Yet they do support OSPF, RIP, and BGP.... Take note that this setup is in a ISP scenario. How can I acheive gateway redundancy?
View 4 Replies View RelatedWe are in the process of installing time clocks at some of our sites around the USA. Our security department has asked that the time clocks be completely isolated from the rest of the network. The time clocks will be administered by ADP via a centralized firewall utilizing NAT. We have multiple subnets available at each site. Let me give an example to calrify what I would like to do. Example: Site A has 10.168.19.0 /24 user subnet and is configured for VLAN1 using 10.168.19.1 on the router as the default gateway. I would like to use subnet 10.168.20.0 /24 for the time clocks, configure it for VLAN2 and use 10.168.20.1 as the router gateway address for VLAN2. This should allow me to NAT one of our additional public IP addresses to the 10.168.20.1 gateway address thus completely isolating the time clocks from the remainder of the network. Problem is I have not done this before so I'm a little confused about how to configure it in the Cisco 3750 switches.
View 6 Replies View Relatedi have one machine have 2 Ethernet devices and i need to connect this server to different 2 network with 2 different gateways (192.168.2.x "vpn network" and 192.168.1.x "adsl network" )so if any other one need to connect this ftp server can connected from vpn or adsl
View 1 Replies View RelatedMy router is showing two separate SSIDs, dlink and dlink 2 it only recently started doing this and around the same time my router has been constantly rebooting when there's little or heavy internet traffic.I have a DIR 655 Hardware Version: A4.Firmware: 1.21 NA
I refuse to go to any version above 1.21 as 1.21 is the most stable firmware for the 655, I have tried all other with terrible outcomes and wireless performance.I've looked around and most people think it's a joke or something, always saying it's probably a neighbors wireless, but that's impossible since I'm on an acreage and my neighbors are too far away for us to be receiving their wireless signals, and if I change the password and encryption type (WPA/WEP/WPA2) I have to change the security settings on both dlink and dlink 2.
Also I have the normal 192.168.0.1 gateway to access the router under the "LAN" section under Status on the router, but under WAN I have a completely different gateway that just recently showed up. I have no idea where this came from or what happened.
The downloadable PDF manual for the WAG160N shows the remote management address as "https://...", while the online support article shows WAG320N screenshots and uses "http://...". The downloadable manuals for the WAG120N & WAG320N don't show either (it's a pretty flimsy manual).point me to, a definitive list of model/firmware combos which do support SSL for remote management?
View 3 Replies View RelatedWe have a HP Procurve 5412zl switch as our default gateway for all our VLANs from there the traffic will be going to a Cisco ASA 5515 and then to a Cisco 3800 Router then to our ISP.
We have yet to purchase the ASA but my question is about my future configuration. I will have the router of last resort on the 5412zl setup to point to the ASA inside interface, how does that work with multiple VLANs? For instance the ASA inside interface would be 10.0.0.1 but traffic could come from another VLAN via the switch with a 192.168.1.x address. Would the ASA just pass it on to the router? Or would it conside this spoofing and drop the packet?
Lastely, if we have WCCP set for the ASA's inside interface, how would it handle the redirect for multiple VLANs ip addresses? Would I use GRE for the redirect to my web filter?
I have a small network that i want to setup, i have 1 2900 router and i'd like to create subinterfaces for the internal. but more importantly i'd like to have the dsl modems connected to the router with traffic from one subinterface going through one modem and traffic from the other going through the other.
View 1 Replies View Relatedremote location on MPLS circuit terminated on a Cisco router that has Internet connectivity through Central Site router. We are installing a cable modem at the remote location that is to be used as the Primary Internet Connection but still be able to use Internet through MPLS if the cable Internet goes down. We want the failover/fallback to be handled automatically.
We have an ASA5505 for the cable Internet which then feeds into the ISPs modem.
At first I was thinking about getting a module for the remote router so the cable Internet could be terminated on the remote router as well but that introduces a single point of failure. I would also like to firewall both the MPLS and the cable Internet but if I do so on the ASA there is another single point of failure.
I have 2x v10000 Websense Security Gateways that are connected to 2x 6500 SUP720. When I turn on cluster management function between Websense appliance, they speak to each other only if they are connected in the same 6500. When they are connected one in every 6500 cluster management does not work. They are connected on the same physical vlan. Do I need multicast to be configured in the 6500 switches?
View 5 Replies View RelatedI am trying to setup internet access and intranet access using two cards per PC. I don't have sever software and I want to be able to share files between several machines. I have two routers. One that connects to cable modem and one that connects to intranet side. I have assigned different static ip addresses to both cards.
View 6 Replies View RelatedI have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?
View 4 Replies View Relatedhave netgear pcmcia card need to connect to new belkin wireless access point.
View 1 Replies View Relatedmy company own a Dell R5400 with remote access card and FX-100 and they are working fine. However, we are considering to connect the R5400 through the Ctrix. Is there any software can be used for controlling R5400 instead of FX-100?
View 1 Replies View RelatedWe have two Cisco 5505 firewalls connecting to two ISP's . The two internal LAN's on the firewalls are 192.168.184.0/24 & 192.168.186.0/24. We also have a Cisco C3560x layer3 switch with vlan interfaces 184.3 & 186.3. We have two DGS-3100 Dlink layer 2 switches connecting our users to the Layer 3. Ip routing is enabled for intervlan communication & I can reach the Switch interfaces & firewall gateways from machines on both on the vlans.We have pbr enabled on the 3560 & users only on the .186 network can get to the internet. The switch is running the ipservices license & the sdm template is "desktop routing" .
Users on the .184 cannot access the internet but we can ping the layer3 interface & the firewall gateway. [code]
I have mobile users using air cards that connect to the network with a VPN product called Net Motion. Our firewall is a ASA 5510. Once connected to the Net Motion VPN server the user will get a DHCP address from our network. In the past we could not get the VPN tunnel to complete since our layer 3 switch (3750G IP services) has 3 egress points and the egress point that we needed the VPN traffic to go out of is not the default gateway. To solve this we had the air card carrier set switch our air cards to static IP addresses and using route statements for the public IP addresses and access lists we got it to work.
The problem with this is that every new air card we provision needs a static IP address. My question is would policy based routing work in this scenario? The problem has been that the VPN tunnel was not able to complete the negotitaion phase as the traffic came into the switch and was trying to go out the default gateway. The VPN client wont get an internal IP address until the VPN tunnel is created.
I would like to get away from using static IP addresses.
I just bought a Huawei E586 Mifi from 3 network in the UK and installed a 32GB micro-SD card. I want to be able to access this card wirelessly, but the "dashboard" (web interface control panel) that is installed doesn't have an option for the SD card. I have seen dashboards on the Internet and also a video on Youtube that do have this option, so I know this can be done.
View 9 Replies View RelatedMay I use an access point as wireless receiver to have internet on RJ45 interface?Is possible that internet source for AP to be on antenna, not on RJ45?
View 4 Replies View RelatedI recently went on vacation an went to connect to my company VPN (using Cisco Anyconnect) while connected with my Verizon Aircard. The process churns for a bit then gives me two error messages."AnyConnect was not able to establish a connection to the specified secure gateway. Please try connecting again.""The VPN connection was terminated due to the loss of the network interface used for the VPN connection."This is the first time using this combination. Using AnyConnect over a wireless connection works fine. The VZ Aircard connection works fine. Just not together. My platform is a Dell E6400 with a Verizon PC5750 running Windows 7 64-bit. Unfortunately, my company support basically stated that they don't have a clue and want to know if it can be resolved once I get back in. Of course that defeats the point. I did notice that the "adapter" created for the aircard does not have the Cisco AnyConnect Network Access Manager Filter Driver listed.
View 1 Replies View RelatedHe's getting a error saying Unidentified Network. After letting fail windows troubleshoot I got 2 errors. The first was "The default gateway is not available, the second was Local Area connection doesn't have a valid ip configuration. Here's what Ive tried so far.I tried in safe mode. Ethernet works here so I assume is a software issue?Uninstalled and reinstalled the drivers. disabled and enabled, nothing..I tried going into configure network card and giving Network Address a random 12 digit value and that failed.Ive tried updating the drivers but I cant because Dell wants me to their download manager into the computer that has no internet to download the drivers /facepalm..I basically ran out of ideas. This is a Dell Studio laptop. It has 2 network cards a wireless and a Ethernet, the ethernet card is a Realtek PCIe GBE Family Controller, The wireless DW1501 Wireless-N WLAN Half-Mini Card
View 5 Replies View Related,I was having problems connecting to a network that is TKIP secured with a WMP11 Wireless PC card. I'm wondering if this is possible.
View 9 Replies View Related