Cisco VPN :: E6400 AnyConnect Fails With VZA Access Air-card
Jul 20, 2011
I recently went on vacation an went to connect to my company VPN (using Cisco Anyconnect) while connected with my Verizon Aircard. The process churns for a bit then gives me two error messages."AnyConnect was not able to establish a connection to the specified secure gateway. Please try connecting again.""The VPN connection was terminated due to the loss of the network interface used for the VPN connection."This is the first time using this combination. Using AnyConnect over a wireless connection works fine. The VZ Aircard connection works fine. Just not together. My platform is a Dell E6400 with a Verizon PC5750 running Windows 7 64-bit. Unfortunately, my company support basically stated that they don't have a clue and want to know if it can be resolved once I get back in. Of course that defeats the point. I did notice that the "adapter" created for the aircard does not have the Cisco AnyConnect Network Access Manager Filter Driver listed.
View 1 Replies
ADVERTISEMENT
Aug 16, 2009
I have a Latitude E6400 that I had to rebuild due to a hard drive failure, with a Dell 1510 WLAN card installed. Upon reinstalling the Dell WLAN Card Utility however, I now receive the following prompt every time I log into my machine:“Reminder: The Dell Wireless WLAN Card is still disabled. Slide the Wireless ON/OFF switch to enable it.”
I am able to connect to wireless networks without any issues, and when enabled it works great. I do however like to keep my wireless radio off when I am not using it. I certainly don’t need the software to tell me that my WLAN card is disabled when I already know that it is. How do I disable this message from coming up each time I log in? I don’t see any options in the software to simply disable reminders, however I don’t want to disable the software from loading altogether.
View 26 Replies
View Related
Jan 25, 2012
I just recently purchased a dell latitude E6400 laptop and I did a clean install of Windows 7 Ultimate 64-bit on it, not an upgrade. I also installed service pack 1 right after the OS install. My problem is I cannot find a single driver that allows my WiFi card/connection to show up in Windows. I have been browsing the internet like a fiend and cannot find a single driver or solution anywhere for this. Every install or driver I try either shows an error saying "incompatable" or just does not fix the issue. All I want is my WiFi card to work, and dell did not have any drivers that worked off of its support site even when I put in my service tag number. compatable driver for the WiFi card for windows 7 64bit? Or steer me in the right direction to get the WiFi working on my laptop?
View 4 Replies
View Related
Sep 26, 2012
I have setup an Anyconnect SSL-VPN in my 2811 and it works just great, but then after the reboot it fails. I think it has something to do with the SSL Cert being ereased. Here is my configuration, if you need anything else:
! Last configuration change at 02:03:27 CDT Thu Sep 27 2012
!
version 15.1
[Code].....
View 6 Replies
View Related
Jan 25, 2012
I'm trying to set up vpn with ASA 8.2(5) and Anyconnect 3.0.4235. The goal is to force user to connect from registered machines only (winXP & win7 x32 and x64). To do this, I used machine certificates issued by own CA. Certificate is installed in machine store. I use double authentication (aaa & certificates). Everything works fine, AnyConnect browses cert store, ASA validating machine certificate, then user is prompted for username/password and finally if all is correct - connection is established.My problem is, that for new installation (new host), AnyConnect fails at first connection attempt. If I use aaa authentication only, connection is established, but if I use aaa & certificates - connection fails. The appropriate .xml profile is predeployed at client host asa well as machine and root certificates.Important: When first try (aaa auth) succeded, others are always OK (with aaa. certificate or aaa & certificate authentication). Only the first one fails.The goal is to succesfuly establish connection with aaa & cert.
With DART i get:
******************************************
Type : Error
Source : acvpnagent
Description : Function: CTransportWinHttp::WinHttpCallback
File: .CTransportWinHttp.cpp
Line: 2150
[code]....
Certificate is valid for sure, and as I mentioned before, if first use aaa only, the second try is OK. At ASA with debug crypto ca 255 can't see any certificate from client.
View 3 Replies
View Related
Dec 13, 2010
I have a Cisco AnyConnect 2.5.2006 failing installation on an upgrade from 2.4.1012. Win7 64-bit.RunOnce exists in the registry and I even added everyone/full perms to it to make sure it wasn't a perms issue. (it seems everyone recommends checking this key exists)I've cleaned the system and the registry multiple time for anything AnyConnect related. The installation 'appears' to fail on the installation of the 64-bit virtual adapter
Installation log is attached to this post.
[code]....
View 11 Replies
View Related
Dec 4, 2012
I have a Latitude E6400 running Windows 7. Yesterday I was able to access the Internet with no problem. Today, I show that I have established a network connection with my Netgear router but I have no Internet connection. My wife has a Toshiba laptop and she has an Internet connection over the same network so the issue must be with my machine.
View 1 Replies
View Related
Aug 10, 2011
I have a CISCO RV220W Wireless router, running the latest firmware (1.0.1.0) and CISCO's AnyConnect Secure Mobility Client v3.0.2052, and Windows 7, 64 bit. My laptop is a corporate based work laptop, and I am trying to use it to connect to my home network ( CISCO RV 220W ).
When I try to connect my PC via the wireless network (to the CISCO Router), via CISCO's AnyConnect Secure Mobility Client, the WiFi connection never actually takes place - rather the CISCO AnyConnect Secure Mobility Client s/w interface suggests that it is "associating" and seems to go into an endless loop. It never receives a DHCP address from the CISCO router. ( see attached picture ).
If I disable the "Cisco AnyConnect Network Access Manager" service, as well as the "Cisco AnyConnect Network Access Manager Logon Module" service within Windows 7, I have no problems establishing a WiFi network with my CISCO router via the traditional Windows approach of connecting to a WiFi network. The inability to connect wirelessly comes back, when these services are re-enabled. It appears to me (a layman) as if the "Network Access Manager" layer is preventing connection to the CISCO router via WiFi.
I have no problems connecting to the CISCO router using CISCO AnyConnect Secure Mobile client over a physical Ethernet cable. I also have a Belkin branded Wireless router that works perfectly with the CISCO AnyConnect Secure Mobility Client. All of the wireless settings on the CISCO RV220W router are factory default.
how I can get the CISCO AnyConnect Secure Mobility Client to play nicely with the CISCO Router when I wish to establish a WiFi connection?
I have also attached the Windows based Event Log associated with this trouble shooting - associated with the "Network Access Manager" logging. SSID C&C@Home is the CISCO Router, whilst SSID Cam@Home is the Belkin wireless router.
View 1 Replies
View Related
Jan 16, 2008
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
View 4 Replies
View Related
Dec 28, 2011
I am trying to connect to my wifi network at my home. I have a Dell Wireless 1397 WLAN Card. I am using an Inspiron 1545 and operating Windows 7.My Router is a Linksys WRT54G. I looked through some old posts and this shows the results of IP Config test I ran:Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.Windows IP Configuration
Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : earthlink.net
[Code].....
View 3 Replies
View Related
Mar 30, 2012
I have a Dell Inspiron 11z (1110) with Dell 1397 mini wireless card. The wireless connection lags/drops persisitently at any time of day or night. When I connect the computer to internet via ethernet the connection is stable. When I run a diagnostics on the wireless card all pass, except the internet IP ping. I get the following message:
The wireless router/AP for your network is working, but your computer is not able to use an IP address to connect to the Internet. You will not be able to connect to the Internet, although you might be able to connect to your local network. Contact your network administrator or wireless router/AP installer for assistance.
I have installed latest driver for the 1397 mini wireless card, albeit a couple of years old.
The wireless router I am using is Netgear Rangemax Dual Band DGND3300v2. I can get into the router administration area but am at a loss as to how to reset/re-install it.
View 1 Replies
View Related
Jan 16, 2012
Are devices (mainly my iPad 2 and Latitude E6400) smart enough to pick 5GHz over 2.4GHz if both networks have the same SSID? Or should I make two separate SSID's for each?
View 6 Replies
View Related
Dec 29, 2010
I recently acquired a Latitude E6510 with Windows 7 Pro 64bit. My Dell DR984 Bluetooth KB/MS receiver works on my Latitude E6400 with win 7 32bit works but fails on the new notebook.I have tried the Broadcomm updater, but it fails with a message that Dell must be contacted. Where can I find drivers so that I can use the DR984 with my new notebook?
View 10 Replies
View Related
Apr 22, 2013
I'd like to ask you which wwan card is the best choice for a dell latitude e6400 laptop.Is it correct that the version 5540 is the newest and probably the best one?
View 7 Replies
View Related
Apr 22, 2013
is there any dell wwan card that is 4G capable and integrable in a latitude E6400 laptop like a wwan 5530 card?
Or the only way to get 4G for E6400 is a USB 4G stick?
View 1 Replies
View Related
Oct 7, 2012
I tried to configure a VPN Anyconnect access to my ISR 887 router.I get the following error in debug:CRYPTO_OPSSL: Can't find router cert. step by step IOS certificate configuring for anyconnect access?
View 1 Replies
View Related
Mar 17, 2011
I am not getting ethernet connection through mt dell E6400 laptop , led at the ethernet port is flashing amber, i am getting PING to that machine & i am connecting with crossover cable
View 1 Replies
View Related
Jul 29, 2011
I am having issues with transfer speed on my network. I have a D-Link DIR-655 wireless N router. Two PC's. My gaming PC is also a server of sorts. E6600, 4 gb of RAM, Wireless N PCI card, Win 7 Pro 64.
I have a small e6400 machine, 4 gb ram, Win 7 Pro 32, 1gigabit connection, hardwired to the router. This one is hooked up to the TV. I want to stream my movie/tv collection from my gamin PC, which is on the other side of the room to the TV. The gaming machine/server has 4 drives, with a dedicated 1tb drive for video storage. The machine connected to the TV has one 300 gb drive. Right now, I am getting 1.8 mbps transfer speeds. This is causing very choppy playback. I am using VLC for playback. I am using WPA2 for network security.
How can i increase my transfer speeds across the network? Is 1.8mbps as good as it gets?
View 11 Replies
View Related
Dec 22, 2011
i have a Dell Latitude E6400. Just reinstalled Vista Ultimate. But it say, "Update Driver Software-Ethernet Controller and Update Driver Software-Network Controller. What I need to install from Dell website?
View 1 Replies
View Related
Sep 27, 2012
With a clean install of Windows 8 64-bit...If I boot the laptop with the Ethernet cable disconnected, I will still get "media disconnected" from ipconfig if I then connect the Ethernet cable after login. The Ethernet connection comes back to life if I put the laptop to sleep and then wake it up, but it will go back to "media disconnected" state again if I unplug and replug the network cable.The laptop has the latest BIOS from Dell from this model (A32 -- and has been reset to the factory settings), but I'm wondering if any of the 21 (!) Advanced driver properties need to be toggled to something else for this particular model of Ethernet card to function. The driver version is 10.1.10.1 (dated 6/25/2012) as installed by Windows 8 64-bit.(I tried "updating" to the 10.1.12.1 driver from Dell's site -- for Windows 7 -- but that one is dated 3/23/2011, oddly enough, and cut down the number of Advance options to 6… -- and it still has the same problem -- Ethernet does not automatically reconnect if I unplug and replug the cable…)Might this be something I need to flip in the BIOS for this model?
I have a Latitude D630 -- running the same build of Windows 8 32-bit (but a different Ethernet adaptor, obviously) -- that does not have this problem. So it's not specifically a Windows 8 issue -- but an issue with the specific Ethernet card.
View 1 Replies
View Related
Nov 27, 2011
I have AnyConnect configured with ASA 8.3 and I'm able to access everything on the internal LAN just fine. However, I cannot connect to the Internet while I'm connected to AnyConnect. I've tried different DNS servers in the AnyConnect profile, different Split Tunnel settings. I just can't seem to figure out the Internet issue. And the strange thing is I can't resolve any Internet addresses either through the AnyConnect connection. When I try pinging [URL] it just says that it can't find the host [URL].
View 6 Replies
View Related
May 9, 2012
We have gotten our anyconnect clients to connect to the VPN with no issues and verifying credentials with RADIUS. Remote users however cannot access internal resources through the VPN. I know I need to setup an NAT Exempt statement for my VPN Pool to the Internal Network,
View 5 Replies
View Related
Sep 13, 2011
I'm having problems getting AnyConnect clients to reach a server (192.168.139.3) on the Inside interface of my ASA 5505. Ideally, this would be accessible from the DfltAccessPolicy or another dedicated policy, but right now I'm happy with any access. Everything else seems to be working as expected. I've rebuilt this config a number of times without success. I can ping the IP from the ASA itself.
View 2 Replies
View Related
Aug 3, 2011
I'm trying to connect two ASA 5505s for a IPSec L2L VPN. They can connect, but not pass traffic from the AnyConnect subnet. I've added the config from ASA-2, with the LAN subnet of 192.168.138.0 and a subnet of 192.168.238.0 for AnyConnect client.
I'm trying to get the AnyConnect Clients access to the 192.168.137.0 LAN behind ASA-1 at 1.1.1.1. Having both 192.168.238.0 and 192.168.138.0 both access 192.168.137.0 is acceptable.
There's probably a lot of cruft in this config, as I've been reading all over forums and docs without much success.
:
ASA Version 8.2(1)
!
hostname asa-wal
names
name 192.168.238.0 anyconnect-vpn
!
interface Vlan1
nameif inside
[code]....
View 7 Replies
View Related
Oct 11, 2012
I just configured a ASA for Remote VPN. I think that every works fine but I have no access to the Clients into the Local LAN behind the ASA.
PC <==internet==>outside ASA inside<=LAN=> PC
After AnyConnect has establised the connection I can ping the inside Interface from the ASA but I can`t Ping the PC behind the inside Interface.
Here is the config of the ASA5505:
: Saved
:
ASA Version 8.2(1)
!
hostname asa5505
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code]....
View 1 Replies
View Related
May 5, 2011
I have a ASA 5540+SSM-40 on which I have configured webvpn and it's listening for connections on the outside interface. It can be accessed from outside the network (the internet) and works just fine. The problem is, I want to access it from inside the network as well but it doesn't work. I can't ping or connect in any way to the IP address of the outside interface from inside (so I suppose it's not strictly related to the configuration of the webvpn).
I don't think it's a ACL issue because the only ACL filtering I do is on the OUTSIDE-IN (facing the internet), the rest are set to permit any.
What I have to do to be able to access the IP address of the outside interface from networks behind the inside interface?
View 5 Replies
View Related
Mar 2, 2013
How can I make my Latitude E6400 connect to my wireless system at start up and stay connected when switching users?
View 1 Replies
View Related
Apr 14, 2011
I have just installed 3 access points along with 6 repeater access points all running V12.4. They are all AIR-AP1242AG-E-K9 using the 2.4GHz radio.
Prior to installation I bench tested that the repeaters would associate with the access points and if one of the access points was turned off the repeaters would automatically roam to another access point. I did not have all 9 devices powered up at the same time, but did have 2 repeaters and 2 access points powered up to simulate association and roaming.
During installation as access points and repeaters were powered up everything behaved as expected (repeaters were associating to access points etc.) however during installation once everything was installed the 3 access points were all powered down for half an hour or so and once powered back on the repeaters did not automatically re-associate until they were re-booted.
I have now configured the repaters with parent MAC addresses to reflect the above current assocaition pattern but not yet powered off the access points to test if this forces re-association as this is now a live operational site!!
Is it normal to have to re-boot the repeaters if ALL 3 access points are powered down at the same time? i.e. If only one access point is powered down will the repeaters automaically roam to another access point o.k.?
View 5 Replies
View Related
Jul 4, 2012
I am unable to access a series of switches connected together through a management vlan. I receive the message "The server xx.xx.xx.xx at level_15_access requires a username and password." Entering the username and password fails and the same username and password message returns. I am able to ssh into the switch with the username and password that fails trying to access the switch with the browser.
How can I check the username and password for access with the browser?
I am trying to monitor switch performance. Is there a good way to monitor switch performance with the command line interface?
View 2 Replies
View Related
Mar 9, 2011
Any guide on configuring 802.1X authentication using the AnyConnect 3.0 NAM module. I have the information required to configure the NAM module but need pointing to a guide on how to set this up on Cisco Secure ACS server side and IOS switches, for example a Catalyst 3750 switch.
View 1 Replies
View Related
Jul 12, 2011
I've read on Cisco AnyConnect 3.0 Q&A that it supports IPSec remote-access VPN: url...I've downloaded and installed AnyConnect 3.0.0629 Secure Mobility Client, but I'm not able to get IPSec VPN working. There's also no option to use PCF files from the previous Cisco IPSec VPN client. How to get IPSec VPN working on AnyConnect 3.0?
View 2 Replies
View Related
Aug 27, 2012
How do I configure the ASA5510 to allow VPN clients to have access to the Internet while they are connected via AnyConnect?
View 6 Replies
View Related
Jun 26, 2012
We have 30 remote workers which we have recently acquired which are being set up with the AnyConnect client to connect to our head end ASA 5510. For security purposes, we have to allow them access to only 3 of our local internal servers, all on our 10.10.X.X/16 subnet. The remotes are being issued a 10.10.50.X/24 address via DHCP on the ASA when connecting. I thought this would be as simple as creating an access list but have not had any luck doing so. In addition, we need to allow them full access to servers in a datacenter connected to our same head end ASA via a site-to-site VPN while they are connected to us using AnyConnect.
View 1 Replies
View Related
