I have setup an Anyconnect SSL-VPN in my 2811 and it works just great, but then after the reboot it fails. I think it has something to do with the SSL Cert being ereased. Here is my configuration, if you need anything else:
! Last configuration change at 02:03:27 CDT Thu Sep 27 2012
!
version 15.1
[Code].....
I'm trying to set up vpn with ASA 8.2(5) and Anyconnect 3.0.4235. The goal is to force user to connect from registered machines only (winXP & win7 x32 and x64). To do this, I used machine certificates issued by own CA. Certificate is installed in machine store. I use double authentication (aaa & certificates). Everything works fine, AnyConnect browses cert store, ASA validating machine certificate, then user is prompted for username/password and finally if all is correct - connection is established.My problem is, that for new installation (new host), AnyConnect fails at first connection attempt. If I use aaa authentication only, connection is established, but if I use aaa & certificates - connection fails. The appropriate .xml profile is predeployed at client host asa well as machine and root certificates.Important: When first try (aaa auth) succeded, others are always OK (with aaa. certificate or aaa & certificate authentication). Only the first one fails.The goal is to succesfuly establish connection with aaa & cert.
With DART i get:
******************************************
Type : Error
Source : acvpnagent
Description : Function: CTransportWinHttp::WinHttpCallback
File: .CTransportWinHttp.cpp
Line: 2150
[code]....
Certificate is valid for sure, and as I mentioned before, if first use aaa only, the second try is OK. At ASA with debug crypto ca 255 can't see any certificate from client.
I recently went on vacation an went to connect to my company VPN (using Cisco Anyconnect) while connected with my Verizon Aircard. The process churns for a bit then gives me two error messages."AnyConnect was not able to establish a connection to the specified secure gateway. Please try connecting again.""The VPN connection was terminated due to the loss of the network interface used for the VPN connection."This is the first time using this combination. Using AnyConnect over a wireless connection works fine. The VZ Aircard connection works fine. Just not together. My platform is a Dell E6400 with a Verizon PC5750 running Windows 7 64-bit. Unfortunately, my company support basically stated that they don't have a clue and want to know if it can be resolved once I get back in. Of course that defeats the point. I did notice that the "adapter" created for the aircard does not have the Cisco AnyConnect Network Access Manager Filter Driver listed.
View 1 Replies View RelatedI have a Cisco2811 SRST/K9 router with a four port FXO that is part of our phone system. It won't ping to anything on the network except for one particular switch. I can ping that switch (but nothing else) and that switch can ping the router and telnet into the router; however, when I plug the router into any other switch on my network, it will still only successfully ping that one switch. It won't ping the switch that it's physically attached to. I can see the router from the switch when I do a Show CDP Neighbor. And I can see the switch when I do a Show CDP Neighbor from the router. But it won't ping. When I do a Show Adjacency from the router, it returns only that one switch. I've tried a Clear ARP on both the switch and the router. I've also compared the config from the router to the config of a working router on the network and everthing looks the same. I can ping anything on my network from these switches - except that router. I even tried changing the default gateway of the router to be the ip address of the switch with which it can successfully communicate.
View 2 Replies View RelatedI have a Cisco AnyConnect 2.5.2006 failing installation on an upgrade from 2.4.1012. Win7 64-bit.RunOnce exists in the registry and I even added everyone/full perms to it to make sure it wasn't a perms issue. (it seems everyone recommends checking this key exists)I've cleaned the system and the registry multiple time for anything AnyConnect related. The installation 'appears' to fail on the installation of the 64-bit virtual adapter
Installation log is attached to this post.
[code]....
I configured Any Connect SSL VPN on Cisco 2811 router. It works perfectly when I lo gin via web and run secure mobility client. However, when I connect directly from the mobility client connection fails. It does not even ask me for username and password.
----------------------------------------------------------------------------------------------------
Mar 7 21:36:47.613: %SSLVPN-5-SSL_TLS_CONNECT_OK: vw_ctx: UNKNOWN vw_gw: VPN_GATEWAY i_vrf: 0 f_vrf: 0 status: SSL/TLS connection successful with remote at
Mar 7 21:36:47.617: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.621: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.745: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.749: WV: Entering APPL with Context: 0x49233618,
[Code]........
--------------------
I have not figured out yet, why mobility client works when launched from the web and why it does not work directly.
I have a CISCO RV220W Wireless router, running the latest firmware (1.0.1.0) and CISCO's AnyConnect Secure Mobility Client v3.0.2052, and Windows 7, 64 bit. My laptop is a corporate based work laptop, and I am trying to use it to connect to my home network ( CISCO RV 220W ).
When I try to connect my PC via the wireless network (to the CISCO Router), via CISCO's AnyConnect Secure Mobility Client, the WiFi connection never actually takes place - rather the CISCO AnyConnect Secure Mobility Client s/w interface suggests that it is "associating" and seems to go into an endless loop. It never receives a DHCP address from the CISCO router. ( see attached picture ).
If I disable the "Cisco AnyConnect Network Access Manager" service, as well as the "Cisco AnyConnect Network Access Manager Logon Module" service within Windows 7, I have no problems establishing a WiFi network with my CISCO router via the traditional Windows approach of connecting to a WiFi network. The inability to connect wirelessly comes back, when these services are re-enabled. It appears to me (a layman) as if the "Network Access Manager" layer is preventing connection to the CISCO router via WiFi.
I have no problems connecting to the CISCO router using CISCO AnyConnect Secure Mobile client over a physical Ethernet cable. I also have a Belkin branded Wireless router that works perfectly with the CISCO AnyConnect Secure Mobility Client. All of the wireless settings on the CISCO RV220W router are factory default.
how I can get the CISCO AnyConnect Secure Mobility Client to play nicely with the CISCO Router when I wish to establish a WiFi connection?
I have also attached the Windows based Event Log associated with this trouble shooting - associated with the "Network Access Manager" logging. SSID C&C@Home is the CISCO Router, whilst SSID Cam@Home is the Belkin wireless router.
We have 1 WLC + 17 AP's on our main site and thats working fine... we just buyed a new AP for a new site of us. Its the same domain, same ip range nothing special at all... Somehow the AP on the site keeps rebooting and the users getting nervous of it there
Specs:
WLC: AIR-CT2504-K9
Software Version: 7.2.110.0
AP:AIR-LAP1042N-E-K9
Software version: 7.2.110.0
[code]....
Would like to enquire regarding 2 x WAP4410N access points that we have installed at our site. These devices work fine with the power brick but when connnected the SG300-28P ports POE lights up, and seems to keep rebooting for some strange reason
View 8 Replies View RelatedAbout twice a week lately I'm having to reboot my router. All connections don't work. Logs captured don't show any time stamping so not as good as I was hoping but I do have some debug data:
View 1 Replies View RelatedI deleted the ios image form the aironet device from command line when i was trying to updgrade it.Now the aironet 1100 keeps rebooting.I've tried to hold down the mode for 30 seconds goes red, but keeps rebooting.
View 2 Replies View RelatedI have 3845 Router which is continuously rebooting; console output is attached.
View 8 Replies View RelatedI have a Linksys RV042 10/100 4-Port VPN Router with Firmware Version 1.3.13.02 and l have noticed that the Router keeps rebooting on average every couple of hours.We have it setup for Load Balancing 2 ADSL Services.
View 3 Replies View RelatedI have a SF 200-24P Cisco switch that seems to be rebooting constantly, When i connect it to mains power it seems to go through a startup cycle, in this order - i have tried this with no network devices attached and the same thing happens
1. Fan starts - continously runs
2. Very quick flash of all RJ45 ports.
3. After about 30 seconds, any network devices connected have an acticity light
4. After about another 45 seconds, all ports light up including the activity and POE orange LEDs for about 5- 10 seconds then go off.
5. About 10 seconds later the ports all light up again and stay on for about 5 seconds.
6. All ports go off and the cycle keeps repeating continously.
I have tried pinging the switch without success.I have also tried disconnecting all devices from each port with no success.At no time does the system LED on the left light up.I have tried resetting to factory default with reset pot on the left side.This is a brand new shipped switch from our cisco supplier, could it be DOA?
I've got a 1941 router that keeps on rebooting by itself every minute. currently, there's no power issue.
I've detected the show version returned a bus error. Is this an IOS bug?
ROUTER uptime is 1 minute
System returned to ROM by bus error at PC 0x222FE2D4, address 0xD0D0D71 at 14:27:13 SGT Tue Nov 27 2012
[Code].....
About every 20 minutes 12 of 300 APs keep rebooting. I have tried moving them to different controllers. I have tried downgrading the code and then upgrading the code. I have tried replacing the AP. I have tried swamping out cables. They are all connected to a 3750 stack but plugged into different switches in the stack. Here is the result that I could capture when I saw it disconnect from the controller. This is the output from the AP:
DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.100.40.212:5246
*Jul 28 14:33:19.595: %WIDS-5-DISABLED: IDS Signature is removed and disabled.
*Jul 28 14:33:19.597: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jul 28 14:33:19.597: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jul 28 14:33:19.655: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
[ code].....
I have removed the ip addresses for security reasons.
I have a brand new lightweight AP that keeps rebooting every 2-3 minutes.
View 1 Replies View RelatedI've got a WRVS4400N V2 Router that just keeps rebooting itself. It powers up, the red LED stays lit, it gets part way through the boot process and reboots itself. I would like to try to re flash the device, but don't know if this is possible in the condition that it is in.
View 3 Replies View RelatedI've got this weird problem with my AP. It keeps rebooting randomly. It happen to all the AP in my campus randomly. It happens recently. It have been commission for quite a long time. ie user able to connect and use it. its connect back to the controller to back in another campus. Below are the logs i gather.
*Jun 7 11:13:54.287: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Jun 7 11:13:54.290: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
[Code]......
I've got a RV220W that for some reason has started acting a bit strange. A couple of times a day the network stops functioning, both wireless and wired. At first I thought this had to do with my newly installed laptop, that it maybe caused some hickup that made the router reboot but even when it's turned off I can still read in the logs of my NAS server (Qnap TS-419P+) that "Lan 1 is down" followed by a "Lan 1 is up" a couple of minutes after.
The things connected to the network by wire is my Macbook Pro (2012), the Qnap and an LG home theater system and the wireless devices are a couple of iPhones and an iPad. The problems started after new years eve and I've been running the latest firmware (1.0.4.17) for a few weeks before that.
The below is the display that I get on the screen when i boot the device.There are two error's one is when the daughter card is found and device give us login access after which it reboot’s. The second is stated below (this is a screen copy of the error)
INIT: version 2.85 booting/mnt/cf/TN-CONFIG on /TN-CONFIG type ext3 (rw,sync,loop=/dev/loop0)/mnt/cf/TN-CERTKEY-STORAGE on /TN-CERTKEY-STORAGE type ext3 (rw,sync,loop=/dev/loop1)/mnt/cf/TN-LOGFILE on /TN-LOGFILE type ext3 (rw,sync,loop=/dev/loop2)/mnt/cf/TN-HOME on /TN-HOME type ext3 (rw,sync,loop=/dev/loop3)/mnt/cf/TN-COREFILE on /TN-COREFILE type ext3 (rw,sync,loop=/dev/loop4)insmod: error inserting
[Code]...
an issue with my modem (i think) I currently cannot get an Internet connection on my computers via wifi for some reason iv tried resetting it but it seems to pick up all the PC's and then 5 minutes later it just drops out which is annoying cause it says that the modem is still receiving Internet and were not getting it iv also tried a new router but the same issue and the speed of Internet is basically halfed what do I do iv tried heaps but it's just ******* me off now
View 1 Replies View RelatedWhy does my D-Link WBR 1310 Router constantly need rebooting? By rebooting I mean unplugging power source for 10-15 seconds then replugging it. This problem has been going on for the last 2-3 months.
View 3 Replies View RelatedI've been having this problem the past 2 days. around 7-7:30pm my motorola sbg6580 will reboot itself every 15m or so the rest of the night.I've checked all my line they are in good condition, I've done the whole pull out all the cords let it sit for 1 minute, I've factory reset it.called the cableone tech support and it even reset while i was on the phone with him. I have a tech coming out tuesday but if it's something i can troubleshoot and fix now i'd rather have that.
View 2 Replies View RelatedMy DIR-655 keeps rebooting multiple times per day. Something in the order of 10-15 times per day. This is not under any heavy load. It's plugged into a decent battery backup providing good clean power. I initially thought its overheating, so I had a fan blow on it all day long, without any change in the issue.
I loved this router when it was working correctly (3+ years). Any way to figure out the cause for the reboot?
I just got a DIR-655, and I got it working, with some effort. However, the wifi stops connecting to the internet every few hours and requires a reboot. Only a reboot of the wifi portion of the router's software, I go to Manual Wireless Connection Setup and save it without changing anything. LAN connections don't experience this.
Comcast Cable connection
DIR-655
Hardware Version: B1
Firmware Version: 2.00NA
I have a switch which is rebooting it self, we bought it a year back,its a new switch, i did not find any error on sh ver after rebooting. I am using OP manager, i did not receive any alerts. I have done all diagnostic test, all are passed, i did not find any problem..
View 2 Replies View RelatedHow do I stop the rv220w from continuously rebooting?
I have been keeping track of when it crashes and reboots and here is what has happened today:
14/03/2013 00:26 crashes and reboots
14/03/2013 07:28 crashes and reboots
14/03/2013 11:14 crashes and reboots
[Code]....
My VMware virtual machine running Prime Infrastructure 1.2 is continiously rebooting.VM console is generating logs as shown below.
View 1 Replies View Relatedour RV220W router has been experiencing random reboots throughout the day, causing a network outage for our local network for the few minutes it takes for the router to start up again. We've seen it reboot at least 5 today alone (and the time is currently just a little over 1pm).I'm having trouble finding the reason for these reboots in the router's logs, although I find these two lines repeating in the error log:
Mon Jan 28 13:20:52 2013(GMT+0100) [rv220w][System][EVTDSPTCH] umiIoctl (18, UMI_CMD_DB_UPDATE(4)) failed. table=dot11STA row=11
Mon Jan 28 13:20:52 2013(GMT+0100) [rv220w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 11 failed. status=-1
I'm not sure why these messages pop up, since we're not using the bandwidth limiter module of the router (granted, we do use QoS profiles to ensure our own LAN is prioritized over the guest VLAN). I'm also not sure whether this is related to the router reboots.
I also find the following repeated line in the warning log:
Mon Jan 28 12:50:50 2013(GMT+0100) [rv220w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
The router is currently running on firmware version 1.0.4.17 (latest official release), since we needed support for hairpin connections (as I found out in a previous thread of mine). I've seen the suggestion of downgrading to a previous firmware version in another thread, which has possibly solved it for the poster in that thread, but as we really need the hairpinning support, I don't know which firmware version is safe enough to downgrade it to, if needed.
I have a set up with an 5508 controller and some AP1141.i get this in the log
LogSystem TimeTrap0Tue Oct 12 14:50:23 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:60:76:50 Cause=Radio reset due to Init. Status:NA1Tue Oct 12 14:50:23 2010AP 'APf866.f292.b28e', MAC: e8:04:62:60:76:50 disassociated previously due to AP Reset. Uptime: 0 days, 00 h 26 m 38 s . Last reset reason: power loss.2Tue Oct 12 14:50:23 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:0b:41:20 Cause=Radio interface reset. Status:NA3Tue Oct 12 14:50:23 2010AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:04:62:0b:41:20 Cause=Radio interface reset. Status:NA4Tue Oct 12 14:50:20 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:0b:41:20 Cause=Radio reset due to Init. Status:NA5Tue Oct 12 14:50:20 2010AP 'APf866.f292.b2f2', MAC: e8:04:62:0b:41:20 disassociated previously due to AP Reset. Uptime: 0 days, 00 h 26 m 44 s . Last reset reason: power loss.6Tue Oct 12 14:49:52 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:60:84:10 Cause=Radio interface reset. Status:NA7Tue Oct 12 14:49:52 2010AP's
[code]....
The ap's are powered from a 3560 poe switch, have movet the ap's to another switch, same problem Controller is running 7.0.98.0
I have a persistent any very annoying issue that the router reboots on it's own when I am streaming video from Netflix or other similar applications.
I read some reviews about this router which stated that this was a known problem, but apparently was resolved with latest firmware updates.
My router is new (less than 1 year). It came originally with the 2.0.1.2 firmware which I updated to the 2.0.1.3
That did not resolve the problem. So my question is, is there any aditional configuration necessary to stream video without interruptions, or, is this a hardware problem?
I have an RV016 V3 with firmware 4.2.1.02 that is constantly rebooting making it unusable. I have one LAN connect and 3 WAN's, 2 DSL's and one Cable Internet in a load balance config. I have tried firmware 4.2.1.01 and it reboots also. do I get and RMA from Linksys and send this pig back?
View 6 Replies View Related