Two Gateways On One Server
Jun 2, 2012
I have a milestone VMS (video management system) server running on a customers site. The server has two network cards. eth0 has a static IP 10.0.15.250, mask 255.255.255.0, gateway 10.0.15.254 (the gateway is a firewall connected to the internet via an eircom modem in bridged mode) eth1 has a static IP 10.94.238.2, mask 255.255.0.0 gateway all the cameras and related equipment are in the range 10.94.238.1 ~ 20 Customers network users what to view the VMS via an application which needs to run on their PC and connect to the VMS server on 10.94.238.2, The customer has given me a gateway address of 10.94.200.1. However when I use this gateway address in the default gateway of eth1 I loose internet access on the server because the server can not resolve the DNS address. The cusotmers users can see the VMS and the monitoring station can see the VMS via a VPN. However I need internet access otherwise Teamviewer will not work and I can not access the server for configuration and maintenance remotely. Is there some other way I can implant the customers gateway so they have access but I still have internet on the server.
View 2 Replies
ADVERTISEMENT
Apr 1, 2012
i have one machine have 2 Ethernet devices and i need to connect this server to different 2 network with 2 different gateways (192.168.2.x "vpn network" and 192.168.1.x "adsl network" )so if any other one need to connect this ftp server can connected from vpn or adsl
View 1 Replies
View Related
Nov 23, 2011
I have two network cards in my computer, one is connected to the ADSL router for a BSNL broadband connection and the other is connected to our compay's MPLS network on which our core software is run , now both networks have different gateways through which they connect , the bsnl ADSL router gets its ip from DHCP ,our MPLS network has its own network ip schema.The problem is I am not able to use both connections simultaneously, if I have to work on our software I have to switch off the ADSL router and if I want to surf the internet then I cannot work on our softwware.
View 3 Replies
View Related
Jul 25, 2012
I've got a network with the following address and subnet mask:
xxx.17.0.0
255.255.0.0
The original gateway that we had on the network is at:
xxx.17.0.254
This gateway is a Netgear VPN firewall and it also has a bit of port forwarding going on to a couple of servers on the network.We've now had a new line put in and we have to use different hardware on that line so in order to phase that in, I've set this up as a new gateway at:
xxx.17.1.254
Internally, the clients and servers are quite happy with this and will happily use the new line.Problem arises when users connect via VPN to the OLD gateway (I haven't got VPN set up on the new one yet). Users can still connect to the VPN but can't see any machine that is using the new gateway.How can I get around that? Does the old gateway need a static route?
View 13 Replies
View Related
Feb 18, 2011
I have a scenario which i would like to discuss with you people. I have a branch office connected with the Head office using wireless radio bridge(point to point connectivity). Here is the configuration at branch office.Things are working fine until now. The branch office has a DSL internet connection and required to be shared among the users. option 1 (problem)DSL terminate on swtich and all clients have a DSL modem as their default gateway and ISP's DNS. Internet works fine but here comes the problem, now they lost the connectivity with head office.Now my question is i cant have two default gateways then what should i do?
I bought dlink dir615 router and want to configure in such a way that internet terminate on dir 615 and branch office pc's should be able to use the internet as well as get connected with the head office with default gateway configuration.
View 7 Replies
View Related
May 9, 2012
We our currently using site-to-site VPN tunnels to connect our multiple offices using static public IP's via ADSL connections.We wanted to get an additional ADSL connection from a different ISP so that if one connection drops, the other could be used.Are there any hardware devices or tricks we can use to automatically get our networks to failover to use the backup ADSL connection and have our VPN traffic remain up?
View 1 Replies
View Related
Oct 13, 2012
I installed m0n0wall in a virtualized environment, i have 10 PCs connected to a router ( 192.168.1.0/24) which connect them to the internet through PPPoE, the problem is that this router does not have a QoS so what i want to do is the following :-
let all the PCs get their IP from the Router and the default gateway will be m0n0wall
the moon wall will have 2 interface (Lan 192.168.1.20) and (Wan 192.168.1.21 and default gateway 192.168.1.1)
now when any PC want to access the internet it should go through m0n0wall and then m0n0wall will forward the connection to the default gateway through the wan interface which is the PPPoE running on the router (192.168.1.1)
View 3 Replies
View Related
Apr 28, 2012
I have two different networks on same LAN.One net has public 2xx.x.x.x IPs (some on DMZ, they are servers with their own internal firewalling) and goes through a GBeth switch to a Cisco 25xx router for accessing HDSL modem with several HDSL trunks and then Internet. That router is configured to let external IPs access only DMZ IPs, of course.The other net has 192.168.x.x IPs and goes through another GBeth switch to a DLink router to access ADSL. Mainly for download traffic at a low flat cost.I would like to have a way to let the 192.x.x.x machines access the servers on the DMZ of the 2xx.x.x.x net without going outside the physical LAN. The servers host mail services and so sending heavy attached documents needs a hi-speed LAN connection and certainly not the ADSL upload capability. Not to say about servers web contents maintenance.
View 1 Replies
View Related
Feb 11, 2011
I need to setup my LAN card to access 2 gateways.
OS: winXP sp3
IP: 192.168.1.101
One gateway is 192.168.1.254 to the internet.Another gateway is 192.168.1.253 to access (via VPN) the other subnets 192.168.x.x? I can even install a second lan card.
View 4 Replies
View Related
Aug 8, 2011
I have LinkSys WAG160N V2 with the last firmware 2.00.20 I have very annoying issue, the Gateway always disconnected from time to time .. Some days it work so fine and some days it disconnect 20 times per day and I have every time to go Status >> Gateway and press connect , another weird thing is that sometimes it gaves me speed 3784 Kbps and sometimes 3500 Kbps , sometimes it gaves me the right speed 4700 Kbps i did think maybe it's my ISP problem , but after the upgrade the problem gone for 3 weeks then it back again, and when it back I did make factory reset and reconfigure it again regarding my ISP settings and it did work fine with 3784 Kbps speed and it should be 4700 Kbps.
View 9 Replies
View Related
Nov 8, 2011
I need to route a subnet from a 7204 to 2 different gateway's which are not Cisco based. I cannot use HSRP, GLBP or VRRP as the other 2 gateways don't support theses protocols. Yet they do support OSPF, RIP, and BGP.... Take note that this setup is in a ISP scenario. How can I acheive gateway redundancy?
View 4 Replies
View Related
Feb 28, 2011
We are in the process of installing time clocks at some of our sites around the USA. Our security department has asked that the time clocks be completely isolated from the rest of the network. The time clocks will be administered by ADP via a centralized firewall utilizing NAT. We have multiple subnets available at each site. Let me give an example to calrify what I would like to do. Example: Site A has 10.168.19.0 /24 user subnet and is configured for VLAN1 using 10.168.19.1 on the router as the default gateway. I would like to use subnet 10.168.20.0 /24 for the time clocks, configure it for VLAN2 and use 10.168.20.1 as the router gateway address for VLAN2. This should allow me to NAT one of our additional public IP addresses to the 10.168.20.1 gateway address thus completely isolating the time clocks from the remainder of the network. Problem is I have not done this before so I'm a little confused about how to configure it in the Cisco 3750 switches.
View 6 Replies
View Related
Jul 2, 2011
My router is showing two separate SSIDs, dlink and dlink 2 it only recently started doing this and around the same time my router has been constantly rebooting when there's little or heavy internet traffic.I have a DIR 655 Hardware Version: A4.Firmware: 1.21 NA
I refuse to go to any version above 1.21 as 1.21 is the most stable firmware for the 655, I have tried all other with terrible outcomes and wireless performance.I've looked around and most people think it's a joke or something, always saying it's probably a neighbors wireless, but that's impossible since I'm on an acreage and my neighbors are too far away for us to be receiving their wireless signals, and if I change the password and encryption type (WPA/WEP/WPA2) I have to change the security settings on both dlink and dlink 2.
Also I have the normal 192.168.0.1 gateway to access the router under the "LAN" section under Status on the router, but under WAN I have a completely different gateway that just recently showed up. I have no idea where this came from or what happened.
View 4 Replies
View Related
Nov 5, 2011
The downloadable PDF manual for the WAG160N shows the remote management address as "https://...", while the online support article shows WAG320N screenshots and uses "http://...". The downloadable manuals for the WAG120N & WAG320N don't show either (it's a pretty flimsy manual).point me to, a definitive list of model/firmware combos which do support SSL for remote management?
View 3 Replies
View Related
Feb 9, 2013
We have a HP Procurve 5412zl switch as our default gateway for all our VLANs from there the traffic will be going to a Cisco ASA 5515 and then to a Cisco 3800 Router then to our ISP.
We have yet to purchase the ASA but my question is about my future configuration. I will have the router of last resort on the 5412zl setup to point to the ASA inside interface, how does that work with multiple VLANs? For instance the ASA inside interface would be 10.0.0.1 but traffic could come from another VLAN via the switch with a 192.168.1.x address. Would the ASA just pass it on to the router? Or would it conside this spoofing and drop the packet?
Lastely, if we have WCCP set for the ASA's inside interface, how would it handle the redirect for multiple VLANs ip addresses? Would I use GRE for the redirect to my web filter?
View 4 Replies
View Related
Apr 4, 2013
I have a small network that i want to setup, i have 1 2900 router and i'd like to create subinterfaces for the internal. but more importantly i'd like to have the dsl modems connected to the router with traffic from one subinterface going through one modem and traffic from the other going through the other.
View 1 Replies
View Related
Apr 11, 2013
remote location on MPLS circuit terminated on a Cisco router that has Internet connectivity through Central Site router. We are installing a cable modem at the remote location that is to be used as the Primary Internet Connection but still be able to use Internet through MPLS if the cable Internet goes down. We want the failover/fallback to be handled automatically.
We have an ASA5505 for the cable Internet which then feeds into the ISPs modem.
At first I was thinking about getting a module for the remote router so the cable Internet could be terminated on the remote router as well but that introduces a single point of failure. I would also like to firewall both the MPLS and the cable Internet but if I do so on the ASA there is another single point of failure.
View 2 Replies
View Related
Dec 8, 2011
I have 2x v10000 Websense Security Gateways that are connected to 2x 6500 SUP720. When I turn on cluster management function between Websense appliance, they speak to each other only if they are connected in the same 6500. When they are connected one in every 6500 cluster management does not work. They are connected on the same physical vlan. Do I need multicast to be configured in the 6500 switches?
View 5 Replies
View Related
Feb 15, 2013
We have two Cisco 5505 firewalls connecting to two ISP's . The two internal LAN's on the firewalls are 192.168.184.0/24 & 192.168.186.0/24. We also have a Cisco C3560x layer3 switch with vlan interfaces 184.3 & 186.3. We have two DGS-3100 Dlink layer 2 switches connecting our users to the Layer 3. Ip routing is enabled for intervlan communication & I can reach the Switch interfaces & firewall gateways from machines on both on the vlans.We have pbr enabled on the 3560 & users only on the .186 network can get to the internet. The switch is running the ipservices license & the sdm template is "desktop routing" .
Users on the .184 cannot access the internet but we can ping the layer3 interface & the firewall gateway. [code]
View 20 Replies
View Related
Oct 6, 2012
I have mobile users using air cards that connect to the network with a VPN product called Net Motion. Our firewall is a ASA 5510. Once connected to the Net Motion VPN server the user will get a DHCP address from our network. In the past we could not get the VPN tunnel to complete since our layer 3 switch (3750G IP services) has 3 egress points and the egress point that we needed the VPN traffic to go out of is not the default gateway. To solve this we had the air card carrier set switch our air cards to static IP addresses and using route statements for the public IP addresses and access lists we got it to work.
The problem with this is that every new air card we provision needs a static IP address. My question is would policy based routing work in this scenario? The problem has been that the VPN tunnel was not able to complete the negotitaion phase as the traffic came into the switch and was trying to go out the default gateway. The VPN client wont get an internal IP address until the VPN tunnel is created.
I would like to get away from using static IP addresses.
View 1 Replies
View Related
Jul 24, 2011
I'am using ASA 5510 and I try to understand how PAT is working.I want to add a Mail Server in the LAN and a webmail using port 3000 on the server. ( webmail must be reachable from the WAN)This is my Configuration :actually LAN users access internet using NAT with one global IP ( 194.x.x.69) which is the ASA WAN interface.
WAN ----- ISP Router ---------- FW ---------- LAN -------- Mail Server + Webmail
| (25) | (3000)
194.x.x.69 192.168.1.254 192.168.1.6
I need to forward port 3000 and port 25 from outside to inside.For example, from the WAN : [URL] must be redirect toward 192.168.1.6:3000 . What is the Correct Configuration ? And what about the Inside/Outside Traffic,Is there any configuration to add ?
View 2 Replies
View Related
Jan 10, 2013
i've been using a VPN to connect to my home network from elsewhere for a few months. It's set up as follows:
PPTP
Maximum Strength Encryption
EAP-MSCHAP-v2 Authentication
Now I find out that MSCHAPv2 authentication has been broken and is no longer considered secure (even by Microsoft), so I want to change the protocol I'm using to make it secure.
However, I've spent 3 hours now researching this and I cannot for the life of me figure out how to use a better protocol on my Windows Server 2012 home server. I've tried setting up PEAP authentication (still PPTP) a la Microsoft's recommendation document, but it requires a certificate. I've created a self-signed certificate but it seems I can't issue certificates (via this method) without being a member of a domain, so I'm stuck. I can't even get started with L2TP since I can't find the option for it.
My question is this: Is there a way to setup a secure VPN server using Windows Server 2012 without a domain? If so, how do I do this?
View 1 Replies
View Related
Dec 9, 2012
I purchased the EA6500 a few days ago, and when I'm connected to Cisco Connect Cloud I am unable to select Folder Access / FTP Server / Media Server. I click them and nothing happens.Also, the Cisco light on the router keeps blinking.
View 5 Replies
View Related
Aug 23, 2011
We have Cisco ASA 5505 with ASDM 5.2 We have one Proxy server in our Local Lab and pointed to Hosted service(Simple Signal)issue is, When our proxy server send register to hosted server, ASA change private IP and post with outside IP and src port as 1063 every time.
Here is debug log on real time monitoring.
Aug 24 2011 05:21:19 302015 203.xxx.xxx.226 192.168.1.51 Built outbound UDP connection 3774 for outside:203.xxx.xxx.226/5060 (203.xxx.xxx.226/5060) to inside:192.168.1.51/27014 (99.119.161.107/1142)
Aug 24 2011 05:21:19 607001 203.xxx.xxx.226 Pre- allocate SIP Via UDP secondary channel for inside:192.168.1.51/27014 to outside:203.xxx.xxx.226 from REGISTER message
Aug 24 2011 05:21:19 710005 203.xxx.xxx.226 99.xxx.xxx.107 UDP request discarded from 203.xxx.xxx.226/5060 to outside:99.xxx.xxx.107/1063
Here 99.xxx.xxx.107 is Our ASA Outside IP address 203.xxx.xxx.226 is Hosted server IP address. My ASA config is attached.
View 2 Replies
View Related
Sep 29, 2011
i am facing the same problem now but am using windows 2003 server
View 1 Replies
View Related
Jul 23, 2012
I put multiple rservers in multiple server farms?
So for example rserver1 and rserver2 are put in serverfarm production1 and are in use with particular sticky and load balancing settings.
Can I then create serverfarm test_production and put both rserver1 and rserver2 in it? Then play around with the sticky and load balancing settings as a test without affecting the production serverfarm.
View 1 Replies
View Related
Feb 16, 2012
I'm trying to design a CSS configuration that allows servers in the same vlan to be the source and destination of load-balanced traffic. My thought is to add two new vlans, one for the VIPs and one for the servers, then NAT the source IPs going from the LB to the servers.
Is this the right way to do it?I've never NATted using CSSs, so I wanted to verify what I'm thinking.Our current config trunks the vlans -
interface 1/1
trunk
vlan 1
default-vlan
vlan 555
[code]....
View 3 Replies
View Related
May 6, 2012
[code]...
I am able to obtain IP addresses through the DHCP server for my clients and I am able to browse internet on the server 2k8.Server 2008 - Share Internet through DHCP server
View 10 Replies
View Related
Feb 11, 2011
I have install the administration toolpack on Windows 7 and enabled remote connections on my server 2008 box, When i try and connect with my Windows 7 server manager it does not work.I see stuff on google about enabling a trustedhost with winrm but can't find a way to do this.
View 18 Replies
View Related
Mar 10, 2011
Is there an iTunes Server for WHS 2011 available?
View 3 Replies
View Related
Aug 28, 2012
After getting New Workstations, I wanted to connect that to the SERVER but Windows 7 could not log into domain of our server with Windows Server 2003. Besides following the proper process/steps. I am able to use the printer and internet shared through SERVER though.
View 2 Replies
View Related
Dec 14, 2010
I've been reading that the Windows Server Backup that is included with Server 08 R2 is pretty good. Is spending $400 on a third party utility worth it?
I'm asking because we're purchasing a new server soon and I want to know if the included backup is going to be good enough. Will be backing up server state as well as data to tape and possibly an off site server (server 2003) if I get my way.
View 19 Replies
View Related
Jan 25, 2013
I know the best thing one should do is install an ISA server and an Active Directory Domain Controller on separate servers. But for some reason, I want to configure my Windows Server 2003 as an ISA server as well as an Active Directory Domain Controller. What can happen to my server making it run improperly. For example, my ISA server will function mainly as a Firewall, I wonder if all the rules I create in ISA server determine what I mean it should work or I have to consider any affection from Active Directory DC to those rules?I have to ask this question because I've already installed both ISA and AD DC on my Windows Server 2003, already created an Allow. All rule (just for testing connection) in ISA server but I can't ping from all the clients to my server, all the clients can ping each other and the server itself can ping to all clients. I just think that may be the affection from AD DC to my AllowAll rule in ISA server.
I successfully created some rules that worked greatly as they should work but when I hadn't installed AD DC yet (just installed ISA), however right after installing AD DC, it still worked well (this made me think that AD DC didn't affect to how ISA works). Then I configured a little related to DNS server, and maybe something I don't remember exactly and now I can't ping from my client PC to my server. My network is virtualized using VMware 8 workstation and GNS3, at first there is no need of GNS3 because I just want to test my internal network (some clients connected to the internal interface of ISA server). Depending on VMware that I can't be sure if it is some fault of VMware or any other thing but my configuration on the servers.
View 5 Replies
View Related
