Protocols / Routing :: Connect Two Net On Same Lan With Two Gateways
Apr 28, 2012
I have two different networks on same LAN.One net has public 2xx.x.x.x IPs (some on DMZ, they are servers with their own internal firewalling) and goes through a GBeth switch to a Cisco 25xx router for accessing HDSL modem with several HDSL trunks and then Internet. That router is configured to let external IPs access only DMZ IPs, of course.The other net has 192.168.x.x IPs and goes through another GBeth switch to a DLink router to access ADSL. Mainly for download traffic at a low flat cost.I would like to have a way to let the 192.x.x.x machines access the servers on the DMZ of the 2xx.x.x.x net without going outside the physical LAN. The servers host mail services and so sending heavy attached documents needs a hi-speed LAN connection and certainly not the ADSL upload capability. Not to say about servers web contents maintenance.
View 1 Replies
ADVERTISEMENT
Feb 15, 2013
We have two Cisco 5505 firewalls connecting to two ISP's . The two internal LAN's on the firewalls are 192.168.184.0/24 & 192.168.186.0/24. We also have a Cisco C3560x layer3 switch with vlan interfaces 184.3 & 186.3. We have two DGS-3100 Dlink layer 2 switches connecting our users to the Layer 3. Ip routing is enabled for intervlan communication & I can reach the Switch interfaces & firewall gateways from machines on both on the vlans.We have pbr enabled on the 3560 & users only on the .186 network can get to the internet. The switch is running the ipservices license & the sdm template is "desktop routing" .
Users on the .184 cannot access the internet but we can ping the layer3 interface & the firewall gateway. [code]
View 20 Replies
View Related
Oct 6, 2012
I have mobile users using air cards that connect to the network with a VPN product called Net Motion. Our firewall is a ASA 5510. Once connected to the Net Motion VPN server the user will get a DHCP address from our network. In the past we could not get the VPN tunnel to complete since our layer 3 switch (3750G IP services) has 3 egress points and the egress point that we needed the VPN traffic to go out of is not the default gateway. To solve this we had the air card carrier set switch our air cards to static IP addresses and using route statements for the public IP addresses and access lists we got it to work.
The problem with this is that every new air card we provision needs a static IP address. My question is would policy based routing work in this scenario? The problem has been that the VPN tunnel was not able to complete the negotitaion phase as the traffic came into the switch and was trying to go out the default gateway. The VPN client wont get an internal IP address until the VPN tunnel is created.
I would like to get away from using static IP addresses.
View 1 Replies
View Related
Nov 3, 2012
I have a problem, i have a DIR-620 wireless router, i can connect to wifi my both ipad and iphone but i cannot connect my laptop, even cannot access the admin page for settings, cz it seems my laptop cannot see my my network...
View 1 Replies
View Related
Feb 4, 2012
I am using RealVNC, have the Viewer and Server installed on three systems on my home network. I have a laptop which I am trying to use to connect to either of my two PC's, but cannot get them connected.With that being said I did have some luck with RealVNC as I have the 5900 and other ports forwarded and was able to connect with my Android tablet and Android Phone to the my two PC's and laptop with no problems....well kind of. I did have issues with this at first till I figured out I had to use a 142.*.*.* ip address because my network ip adresses were behind a NAT IP.Now back to the connecting my laptop to my two PC's issue.I have tried using the 142.*.*.* ip address and I have tried using my network ip 192.*.*.* to no avail. I just can't seem to connect.
View 5 Replies
View Related
Nov 8, 2011
I need to route a subnet from a 7204 to 2 different gateway's which are not Cisco based. I cannot use HSRP, GLBP or VRRP as the other 2 gateways don't support theses protocols. Yet they do support OSPF, RIP, and BGP.... Take note that this setup is in a ISP scenario. How can I acheive gateway redundancy?
View 4 Replies
View Related
Feb 16, 2011
The whole thing about IPv6 has been out for what is probably a couple of years now. But I find it very odd how even my newest modem/router can't even support it yet. Why on earth are manufacturers such as Netgear holding back so much on making their products IPv6 compatible? The IANA has just about given out what is left of the addresses, and we still have time to adapt by working our way over to IPv6 as it can work simultaneously with IPv4. Companies have been given years to prepare.
Why can't I connect to the Internet right now using IPv6? Not only is my router holding me back, but will my ISP hold me back as well?
View 1 Replies
View Related
Sep 23, 2012
I have a Rover system DVR 4CH with 4 CCTV camera's connected to it i want to view it through a computer stream it on the internet for free i dont want to use DYN web hosting because it cost money.
View 1 Replies
View Related
Apr 6, 2011
Basically, I was following instructions of how to forward a port to get higher speeds on bitcomet.After doing allsorts which I don't understand (yes, very stupid I know, but I've learned my lesson now), I restarted my computer and have since been unable to connet to the internet.
I have tried a system restore which didn't work and also searched google for hours but to no avail.When I diagnose the problem with windows,it states," "Wireless Network Connection" doesn't have a valid IP configuration.I am running Windows 7 btw.
View 5 Replies
View Related
Mar 4, 2013
In recent days, there was an electrical fault and my computer does not automatically connect to the wireless network in the house, since then. I do not know what happened.
View 1 Replies
View Related
Feb 23, 2011
I was about to portforward to be able to make an minecraft server. but i can't connect to the default gateway 192.168.1.1 so for the moment i use hamachi but i would wannt to portforward it to make it easier for others to join.
View 3 Replies
View Related
Jul 12, 2011
I set up the password through WPA-PSK, the problems come up. My laptop, HP G62-465DX and my Ipod Touch can connect by inputting the passcode but the other laptop in my family, HP G72-b60us, cannot connect to the router once the passcode is set up because the laptop claims that it is incompatible with the router when it was before. Also, my wireless printer HP Officejet 4500 wireless G510 n-z does not work when the passcode is set-up.
View 5 Replies
View Related
Jan 23, 2012
how to connect a pc to a hdtv wirelessly. The tv is to be used like a monitor. I want to display a PowerPoint file. Currently there is a lan already setup in the workplace. I have looked at some pc to tv devices but am not sure if they would work. My company's TIS department wants to put a wireless card in the workstation pc but is not sure how to connect the tv as a monitor?
View 1 Replies
View Related
Jan 8, 2011
For some reason, our router donwstairs was kicking one or more of our (4pc's downstairs, one occasionally upstairs) off. My son connected another router upstairs and then created a static IP for everything. It seems when he did that, our Brother 2170 wireless printer quit working. We've tried everything to get it going again and nothing works- even Brother didn't get it rectified. Earlier today, my son finally got it working, connected directly to the router to get the static IP on the printer (I guess). But when he disconnected it (hardwired) from the router, it won't work again
View 5 Replies
View Related
Mar 31, 2012
can i connect to internet without settings in modem is dat possible?
View 3 Replies
View Related
Aug 8, 2011
My dlink aircard wont connect to wpa psk networks.Why is that.
View 5 Replies
View Related
Jul 26, 2011
I have set up several types of servers on my computer (ftp, game servers, web servers, etc).
I have had a problem with people connecting to any of my servers. I know for a fact I have port forwarded correctly (I have checked 12 times, and I have never had a problem port forwarding). I know it's not my firewall, the problem persists when I completely shut it down.
I had an ftp and web server working about a week ago. No one can connect to any server, be it ftp...web...etc.
My router is a Netgear WNR2000v2
View 6 Replies
View Related
Jul 28, 2011
I recently am trying to get an open nat type so I can play Playstation network better. I watched a video and they told me to turn off the NAT and I did now it does not let me connect to the router page now, I can connect to the internet and stuff but I can't connect to the router page
View 19 Replies
View Related
May 24, 2011
I am trying to get my daughters laptop re-hooked to the wifi. Other computers and smart phones have no problems. This computer was connected but after the applesauce spill on the keyboard, and subsequent MicroCenter replacement of keyboard, we cannot get the laptop online.It is an Acer Aspire 5517 running Windows 7I have removed all profiles and created a new profile entering parameters from my laptop. I can see the wireless connection, but when I try to connect, I get "Windows was unable to connect to Greg". When I click troubleshoot, I get "Troubleshooting couldn't identify the problem".
View 2 Replies
View Related
Mar 14, 2011
I am trying to connect wirelessly to my BT Home Hub via a USB Wireless adaptor. The homehub works perfectly and I have other laptops in the house connecting via the wireless networkHowever, this is the problem. The Wireless connection status shows as good but packets only being sent and not received. Therefore when I load Internet Explorer, I get WebPage Not availableI notice that my IP address is starts with 169 and researching forums suggests that this is the problem and it should start 192? I have tried all sorts of things but simply cannot get this resolved. If I plug the HomeHub into the laptop directly, the connection via the ethernet cable works fine.
View 6 Replies
View Related
Jan 21, 2011
My customer has 3 computer
1- Windows xp
2- Win7
3- Apple
4 new sony laptop.
Vaio would not connect using WEP 40-bit key. Logged into Airport Extreme router with Airport setup utility for Windows from Apple. Updated firmware from 5.1.1 to 5.7. Reset Encryption from WEP to WPA/WPA2 Personal.Connected Vaio on Wifi using WPA2. Removed ethernet cable and connection was good at 54MB/s.Completed Windows Update
View 3 Replies
View Related
Mar 9, 2013
I had a power outage while online and when power resumed, I was no longer able to connect to the internet via my wireless router. My laptops (I have 2, work and personal) both receive the wireless signal from my router (a Linksys WRT54GC) but I get a 'DNS lookup failed' error message when trying to access the internet. My standard set up was Arris cable modem-->Linksys router-->Laptop but I've had to go cable modem-->Laptop via Ethernet in order to access the internet.
Both laptops are running WinXP Pro, SP3 and I ran 'ipconfig/all' on my work one, once when connected via Ethernet and once when I had my wireless connection enabled (but again, not connected to the internet). Results below.
Ipconfig/all when connected via Ethernet to cable modem:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and Settingsm03015a>ipconfig/all
[Code].....
View 19 Replies
View Related
Apr 4, 2013
I have a small network that i want to setup, i have 1 2900 router and i'd like to create subinterfaces for the internal. but more importantly i'd like to have the dsl modems connected to the router with traffic from one subinterface going through one modem and traffic from the other going through the other.
View 1 Replies
View Related
Apr 11, 2013
remote location on MPLS circuit terminated on a Cisco router that has Internet connectivity through Central Site router. We are installing a cable modem at the remote location that is to be used as the Primary Internet Connection but still be able to use Internet through MPLS if the cable Internet goes down. We want the failover/fallback to be handled automatically.
We have an ASA5505 for the cable Internet which then feeds into the ISPs modem.
At first I was thinking about getting a module for the remote router so the cable Internet could be terminated on the remote router as well but that introduces a single point of failure. I would also like to firewall both the MPLS and the cable Internet but if I do so on the ASA there is another single point of failure.
View 2 Replies
View Related
Apr 11, 2013
I am trying to connect two Asterisk Server (with DHCP server enabled on both) on a HP Pro Curve 2626 switch. Server A has IP address 192.168.2.1 and Server B has IP address 192.168.3.1. I created a two new VLAN on switch, VLAN2 for 192.168.2.0 network and VLAN3 for 192.168.3.1 network. I put the command "ip routing" on the switch. My goal is to be able to ping ip address from PC 1(VLAN2) to PC 2(VLAN3) and vice versa... I'm not sure what I am missing... By the way, there is NO ROUTER involved on this set up. I tried to Google and it says HP ProCurve 2626 is a Layer 3 switch so IP routing should be possible.
View 4 Replies
View Related
Dec 14, 2011
I've got a problem with my Linksys E1000 router. When I bought it, it worked without trouble. Setup was easy and straight forward and I was able to connect all my wireless devices (2 latops, a mobile) without any problem. Then, after two months or so, I noticed the laptops were losing internet connection (or not finding the wireless network on start up). Rebooting the router seemed to work the first couple of times to restore the wireless connections, but after a few more days, the wireless network either shows up and the devices are unable to connect to it OR the wireless network does not appear in the network list. However, the wired connection to my desktop PC via ethernet cable has no issues at all. My conclusion is that these wireless routers (E1000) have a defect in the radio card.
View 6 Replies
View Related
Dec 8, 2011
I have 2x v10000 Websense Security Gateways that are connected to 2x 6500 SUP720. When I turn on cluster management function between Websense appliance, they speak to each other only if they are connected in the same 6500. When they are connected one in every 6500 cluster management does not work. They are connected on the same physical vlan. Do I need multicast to be configured in the 6500 switches?
View 5 Replies
View Related
May 13, 2012
I bought yesterday a wireless modem/router and Tp-Link Adsl2+ N300 Modem Router Td-W8960n.I have 2 laptop computers at home.The first issue I have is that with one of the laptops (quite old - Acer Aspire 2420-2579 with Windows Vista Basic Service Pack 1) I can not connect (wireless) to the internet. It says local access only. However in other countries (IM in NZ) it does connect to internet. It does work when I use an Ethernet cable between my router and the laptop. The second issue is with my other laptop. A HP Pavillion DV-4 windows vista home premium service pack 2. I manage to get wireless access to the internet but every couple of minutes the connections drops and starts again by itself�. After 1-2 min approx�. it is getting pretty annoying!I don�t think it is the routher as I also have an XBOX 360 connectet to the internet usign the same device and works absolutely fine!
View 6 Replies
View Related
Jun 2, 2012
I have a milestone VMS (video management system) server running on a customers site. The server has two network cards. eth0 has a static IP 10.0.15.250, mask 255.255.255.0, gateway 10.0.15.254 (the gateway is a firewall connected to the internet via an eircom modem in bridged mode) eth1 has a static IP 10.94.238.2, mask 255.255.0.0 gateway all the cameras and related equipment are in the range 10.94.238.1 ~ 20 Customers network users what to view the VMS via an application which needs to run on their PC and connect to the VMS server on 10.94.238.2, The customer has given me a gateway address of 10.94.200.1. However when I use this gateway address in the default gateway of eth1 I loose internet access on the server because the server can not resolve the DNS address. The cusotmers users can see the VMS and the monitoring station can see the VMS via a VPN. However I need internet access otherwise Teamviewer will not work and I can not access the server for configuration and maintenance remotely. Is there some other way I can implant the customers gateway so they have access but I still have internet on the server.
View 2 Replies
View Related
Nov 23, 2011
I have two network cards in my computer, one is connected to the ADSL router for a BSNL broadband connection and the other is connected to our compay's MPLS network on which our core software is run , now both networks have different gateways through which they connect , the bsnl ADSL router gets its ip from DHCP ,our MPLS network has its own network ip schema.The problem is I am not able to use both connections simultaneously, if I have to work on our software I have to switch off the ADSL router and if I want to surf the internet then I cannot work on our softwware.
View 3 Replies
View Related
Jul 25, 2012
I've got a network with the following address and subnet mask:
xxx.17.0.0
255.255.0.0
The original gateway that we had on the network is at:
xxx.17.0.254
This gateway is a Netgear VPN firewall and it also has a bit of port forwarding going on to a couple of servers on the network.We've now had a new line put in and we have to use different hardware on that line so in order to phase that in, I've set this up as a new gateway at:
xxx.17.1.254
Internally, the clients and servers are quite happy with this and will happily use the new line.Problem arises when users connect via VPN to the OLD gateway (I haven't got VPN set up on the new one yet). Users can still connect to the VPN but can't see any machine that is using the new gateway.How can I get around that? Does the old gateway need a static route?
View 13 Replies
View Related
Feb 18, 2011
I have a scenario which i would like to discuss with you people. I have a branch office connected with the Head office using wireless radio bridge(point to point connectivity). Here is the configuration at branch office.Things are working fine until now. The branch office has a DSL internet connection and required to be shared among the users. option 1 (problem)DSL terminate on swtich and all clients have a DSL modem as their default gateway and ISP's DNS. Internet works fine but here comes the problem, now they lost the connectivity with head office.Now my question is i cant have two default gateways then what should i do?
I bought dlink dir615 router and want to configure in such a way that internet terminate on dir 615 and branch office pc's should be able to use the internet as well as get connected with the head office with default gateway configuration.
View 7 Replies
View Related
Aug 20, 2011
why the WAN protocols like Frame-relay, HDLC and PPP are called Layer2 protocols?What is the address scheme they use?
View 5 Replies
View Related
