Protocols / Routing :: Why Can't Connect To The Internet Right Now Using IPv6

Feb 16, 2011

The whole thing about IPv6 has been out for what is probably a couple of years now. But I find it very odd how even my newest modem/router can't even support it yet. Why on earth are manufacturers such as Netgear holding back so much on making their products IPv6 compatible? The IANA has just about given out what is left of the addresses, and we still have time to adapt by working our way over to IPv6 as it can work simultaneously with IPv4. Companies have been given years to prepare.

Why can't I connect to the Internet right now using IPv6? Not only is my router holding me back, but will my ISP hold me back as well?

View 1 Replies


ADVERTISEMENT

Protocols / Routing - Changed IP And Now Can't Connect To Internet?

Apr 6, 2011

Basically, I was following instructions of how to forward a port to get higher speeds on bitcomet.After doing allsorts which I don't understand (yes, very stupid I know, but I've learned my lesson now), I restarted my computer and have since been unable to connet to the internet.

I have tried a system restore which didn't work and also searched google for hours but to no avail.When I diagnose the problem with windows,it states," "Wireless Network Connection" doesn't have a valid IP configuration.I am running Windows 7 btw.

View 5 Replies View Related

Protocols / Routing :: Unable To Connect To Internet

Mar 4, 2013

In recent days, there was an electrical fault and my computer does not automatically connect to the wireless network in the house, since then. I do not know what happened.

View 1 Replies View Related

Protocols / Routing :: Can Connect To Internet Without Settings In Modem

Mar 31, 2012

can i connect to internet without settings in modem is dat possible?

View 3 Replies View Related

Protocols / Routing :: WRT54GC - Getting Wireless Signal But Cannot Connect To Internet?

Mar 9, 2013

I had a power outage while online and when power resumed, I was no longer able to connect to the internet via my wireless router. My laptops (I have 2, work and personal) both receive the wireless signal from my router (a Linksys WRT54GC) but I get a 'DNS lookup failed' error message when trying to access the internet. My standard set up was Arris cable modem-->Linksys router-->Laptop but I've had to go cable modem-->Laptop via Ethernet in order to access the internet.

Both laptops are running WinXP Pro, SP3 and I ran 'ipconfig/all' on my work one, once when connected via Ethernet and once when I had my wireless connection enabled (but again, not connected to the internet). Results below.

Ipconfig/all when connected via Ethernet to cable modem:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and Settingsm03015a>ipconfig/all

[Code].....

View 19 Replies View Related

Protocols / Routing :: Linksys E1000 Router Failed To Connect To Internet

Dec 14, 2011

I've got a problem with my Linksys E1000 router. When I bought it, it worked without trouble. Setup was easy and straight forward and I was able to connect all my wireless devices (2 latops, a mobile) without any problem. Then, after two months or so, I noticed the laptops were losing internet connection (or not finding the wireless network on start up). Rebooting the router seemed to work the first couple of times to restore the wireless connections, but after a few more days, the wireless network either shows up and the devices are unable to connect to it OR the wireless network does not appear in the network list. However, the wired connection to my desktop PC via ethernet cable has no issues at all. My conclusion is that these wireless routers (E1000) have a defect in the radio card.

View 6 Replies View Related

Protocols / Routing :: Cannot Connect Wireless Tp-Link Adsl2+ N300 Modem To The Internet

May 13, 2012

I bought yesterday a wireless modem/router and Tp-Link Adsl2+ N300 Modem Router Td-W8960n.I have 2 laptop computers at home.The first issue I have is that with one of the laptops (quite old - Acer Aspire 2420-2579 with Windows Vista Basic Service Pack 1) I can not connect (wireless) to the internet. It says local access only. However in other countries (IM in NZ) it does connect to internet. It does work when I use an Ethernet cable between my router and the laptop. The second issue is with my other laptop. A HP Pavillion DV-4 windows vista home premium service pack 2. I manage to get wireless access to the internet but every couple of minutes the connections drops and starts again by itself�. After 1-2 min approx�. it is getting pretty annoying!I don�t think it is the routher as I also have an XBOX 360 connectet to the internet usign the same device and works absolutely fine!

View 6 Replies View Related

Protocols / Routing :: Connect Two Net On Same Lan With Two Gateways

Apr 28, 2012

I have two different networks on same LAN.One net has public 2xx.x.x.x IPs (some on DMZ, they are servers with their own internal firewalling) and goes through a GBeth switch to a Cisco 25xx router for accessing HDSL modem with several HDSL trunks and then Internet. That router is configured to let external IPs access only DMZ IPs, of course.The other net has 192.168.x.x IPs and goes through another GBeth switch to a DLink router to access ADSL. Mainly for download traffic at a low flat cost.I would like to have a way to let the 192.x.x.x machines access the servers on the DMZ of the 2xx.x.x.x net without going outside the physical LAN. The servers host mail services and so sending heavy attached documents needs a hi-speed LAN connection and certainly not the ADSL upload capability. Not to say about servers web contents maintenance.

View 1 Replies View Related

Protocols / Routing :: DIR-620 - Cannot Connect Laptop

Nov 3, 2012

I have a problem, i have a DIR-620 wireless router, i can connect to wifi my both ipad and iphone but i cannot connect my laptop, even cannot access the admin page for settings, cz it seems my laptop cannot see my my network...

View 1 Replies View Related

Protocols / Routing :: Cannot Connect Using Real VNC

Feb 4, 2012

I am using RealVNC, have the Viewer and Server installed on three systems on my home network. I have a laptop which I am trying to use to connect to either of my two PC's, but cannot get them connected.With that being said I did have some luck with RealVNC as I have the 5900 and other ports forwarded and was able to connect with my Android tablet and Android Phone to the my two PC's and laptop with no problems....well kind of. I did have issues with this at first till I figured out I had to use a 142.*.*.* ip address because my network ip adresses were behind a NAT IP.Now back to the connecting my laptop to my two PC's issue.I have tried using the 142.*.*.* ip address and I have tried using my network ip 192.*.*.* to no avail. I just can't seem to connect.

View 5 Replies View Related

Protocols / Routing :: Rover System DVR 4CH Connect To Pc?

Sep 23, 2012

I have a Rover system DVR 4CH with 4 CCTV camera's connected to it i want to view it through a computer stream it on the internet for free i dont want to use DYN web hosting because it cost money.

View 1 Replies View Related

Protocols / Routing :: Can't Connect To Default Gateway

Feb 23, 2011

I was about to portforward to be able to make an minecraft server. but i can't connect to the default gateway 192.168.1.1 so for the moment i use hamachi but i would wannt to portforward it to make it easier for others to join.

View 3 Replies View Related

Protocols / Routing :: Cannot Connect To Router Once Passcode Is Set Up

Jul 12, 2011

I set up the password through WPA-PSK, the problems come up. My laptop, HP G62-465DX and my Ipod Touch can connect by inputting the passcode but the other laptop in my family, HP G72-b60us, cannot connect to the router once the passcode is set up because the laptop claims that it is incompatible with the router when it was before. Also, my wireless printer HP Officejet 4500 wireless G510 n-z does not work when the passcode is set-up.

View 5 Replies View Related

Protocols / Routing :: Connect A Pc To A Hdtv Wirelessly?

Jan 23, 2012

how to connect a pc to a hdtv wirelessly. The tv is to be used like a monitor. I want to display a PowerPoint file. Currently there is a lan already setup in the workplace. I have looked at some pc to tv devices but am not sure if they would work. My company's TIS department wants to put a wireless card in the workstation pc but is not sure how to connect the tv as a monitor?

View 1 Replies View Related

Protocols / Routing :: Using Static IP Now Wireless Printer Won't Connect?

Jan 8, 2011

For some reason, our router donwstairs was kicking one or more of our (4pc's downstairs, one occasionally upstairs) off. My son connected another router upstairs and then created a static IP for everything. It seems when he did that, our Brother 2170 wireless printer quit working. We've tried everything to get it going again and nothing works- even Brother didn't get it rectified. Earlier today, my son finally got it working, connected directly to the router to get the static IP on the printer (I guess). But when he disconnected it (hardwired) from the router, it won't work again

View 5 Replies View Related

Protocols / Routing :: D-link Air-card Won't Connect To Wpa Psk Networks

Aug 8, 2011

My dlink aircard wont connect to wpa psk networks.Why is that.

View 5 Replies View Related

Protocols / Routing :: NR2000v2 - Cannot Connect To Computer Using Public Ip

Jul 26, 2011

I have set up several types of servers on my computer (ftp, game servers, web servers, etc).

I have had a problem with people connecting to any of my servers. I know for a fact I have port forwarded correctly (I have checked 12 times, and I have never had a problem port forwarding). I know it's not my firewall, the problem persists when I completely shut it down.

I had an ftp and web server working about a week ago. No one can connect to any server, be it ftp...web...etc.

My router is a Netgear WNR2000v2

View 6 Replies View Related

Protocols / Routing :: Cannot Connect To Router Page On Browser

Jul 28, 2011

I recently am trying to get an open nat type so I can play Playstation network better. I watched a video and they told me to turn off the NAT and I did now it does not let me connect to the router page now, I can connect to the internet and stuff but I can't connect to the router page

View 19 Replies View Related

Protocols / Routing :: Acer Notebook Cannot Connect To Wifi?

May 24, 2011

I am trying to get my daughters laptop re-hooked to the wifi. Other computers and smart phones have no problems. This computer was connected but after the applesauce spill on the keyboard, and subsequent MicroCenter replacement of keyboard, we cannot get the laptop online.It is an Acer Aspire 5517 running Windows 7I have removed all profiles and created a new profile entering parameters from my laptop. I can see the wireless connection, but when I try to connect, I get "Windows was unable to connect to Greg". When I click troubleshoot, I get "Troubleshooting couldn't identify the problem".

View 2 Replies View Related

Protocols / Routing :: Two Paths To Internet One Network

Jul 27, 2011

I have a local DSL line in our remote office. We are connecting a microwave antennae that carries our main office internet to the remote office.I want to be able to connect both paths to a Layer 3 switch and route traffic through the main office with the router connected to the DSL as a fail-over solution.I would really like to stick with HP Procurve's if possible.

View 3 Replies View Related

Protocols / Routing :: Who Is Your Internet Service Provider

Sep 4, 2012

Is this a wired or wireless connection issue? Both Who is your Internet Service Provider (ISP)? Comcast..What type of Broadband connection are you using? Cable..What is the exact Make and Model of your Modem, Router or Modem/Router Combo - (Main)Netgear WNR3700v2 / WNR2000v3(secondary) My current setup is the 3700 router is taking the internet from the modem cat5e and spewing the wireless. I would like to have the secondary router use the wireless from router 1 as the internet source and push the internet out of the 4 hardline ports so I can plug my upstairs xbox 360 into the router via cat5e. I'm just kinda new to this and still learning so I'm not sure how to configure the router to do this. I can get into the settings of the router just fine but finding the right settings to tweak is a little difficult.

View 3 Replies View Related

Protocols / Routing :: IP Camera Not Accessible Through Internet

Feb 28, 2012

I purchased an IP Cam for my girl friend to monitor her dog, she lives in an apartment complex that provides internet. I have been able to get the camera setup at my house to be accessed through the internet. I have a cable modem and a router, setup a dyndns account, port forwarded my router and boom it worked. Went to my gf's apartment and I didn't think of it at first until I was frustrated, but realized the apartment complex probably has a router of its own. I can access the cam on her LAN but not through the internet.

View 3 Replies View Related

Protocols / Routing :: Connecting To Internet Via Router

Mar 31, 2011

I have att dsl and they supplied me with a modem, a motorola model type 2210, and my belkin surf N300 router is giving me issues connecting to the internet. Im pretty sure my wireless network adapter is a netgear wg311v3.The issue im having is that sometimes i can connect to the internet just fine, and sometimes i cant connect to the internet. I know it is a router issue because when i plug the modem into my comp, i can access the internet 100% fine.I also think it is not a wireless network adapter issue because i ran an ethernet cable from the router to my comp and had the same issues. There are 2 other computers on the network, one of them is a year or two newer than my dell desktop, and has no issues whatsoever connecting to the internet via the router. The other computer on the network is a Wii, and has connection issues when playing online (probly a different issue), but can access the internet no problem.

View 1 Replies View Related

Protocols / Routing :: No Internet Access With New Router

Dec 18, 2012

I have a little problem with installing my new router. There were quite a lot of problems with the old smc, so I've bought a TP-Link router. I installed it just alright, it said congratulations, you have internet. I don't have though, not even on the directly plugged computer. It's kind of frustrating, since the old router is still working like before. So I plugged an ethernet cable from the old router's lan to the tp-link wan and with that, the new network is working just fine. The problem with the internet access occurs only, if the router is directly plugged to the modem. (The computers do find the network but the connection is kind of offline.) I don't really know what could be the problem, since I'm a little new to routers. I've read almost everything in the new router's manual and I'm pretty sure it's installed correctly. (ADSL username and password copied from the old settings, mac address copied, all ip addresses pinged, done power cycle etc..) I thought about resetting the modem, but I'm a bit afraid of losing the old router's internet connection as well.

View 8 Replies View Related

Protocols / Routing :: Trying To Connect Wirelessly To BT Home Hub Via A USB Wireless Adapter?

Mar 14, 2011

I am trying to connect wirelessly to my BT Home Hub via a USB Wireless adaptor. The homehub works perfectly and I have other laptops in the house connecting via the wireless networkHowever, this is the problem. The Wireless connection status shows as good but packets only being sent and not received. Therefore when I load Internet Explorer, I get WebPage Not availableI notice that my IP address is starts with 169 and researching forums suggests that this is the problem and it should start 192? I have tried all sorts of things but simply cannot get this resolved. If I plug the HomeHub into the laptop directly, the connection via the ethernet cable works fine.

View 6 Replies View Related

Protocols / Routing :: Can't Connect Three Computer After 4th Laptop Join Network

Jan 21, 2011

My customer has 3 computer

1- Windows xp

2- Win7

3- Apple

4 new sony laptop.

Vaio would not connect using WEP 40-bit key. Logged into Airport Extreme router with Airport setup utility for Windows from Apple. Updated firmware from 5.1.1 to 5.7. Reset Encryption from WEP to WPA/WPA2 Personal.Connected Vaio on Wifi using WPA2. Removed ethernet cable and connection was good at 54MB/s.Completed Windows Update

View 3 Replies View Related

Protocols / Routing :: Escalate An Internet Routing Beyond My ISP?

Apr 5, 2013

We have a PPPoE DSL link with a dedicated IP providing by a small ISP(ISP A) in Canada. We are having trouble reaching a small group of IPs in the US to be able to access some client resources.We have eliminated all possible local issues by removing the firewall and making a direct connection to the ISP. We have also had numerous tests prove successful when we use other local ISPs.

Trace routes show that the packets get dropped a few hops from the destination on a US ISP(ISP B).The routes even appear to be very similar to the other ISPs we tested. We escalated to ISP A and they say that everything is working properly on their end and the problem is with ISP B. They claim they "have no partnership with ISP B and therefore cannot create a ticket to get it resolved". I tried calling ISP B but I get nowhere because I am not a customer of theirs.

My solution is to give ISP A the boot, but management has denied that request because of the amount of effort required to switch over. How I can escalate this? Is there anyway to go over and above the ISPs?

View 4 Replies View Related

Protocols / Routing :: Laptop Connected To Modem But Not The Internet

Aug 20, 2012

Just yesterday my laptop could connect to the Internet. Now it would just connect to the modem (via wi-fi), and there would be no Internet connection. All other computers in my house using wi-fi work fine.Here are my results when I type in the ipconfig /all in the command prompt.

Configuration IP de Windows

Nom de l'h�te . . . . . . . . . . : Loc-PC
Suffixe DNS principal . . . . . . :
Type de noeud. . . . . . . . . . : Diffusion
Routage IP activ� . . . . . . . . : Non

[code]....

View 6 Replies View Related

Protocols / Routing :: No Internet Access After Reset The Modem?

Dec 12, 2012

I have reset the modem but after resetting it I can't go for internet anymore with computer or wifi . And after that I notice that my wifi is not under any security which is free for all.can I know how to fix this problem ?the main problem is mostly that can't go internet after reset it

View 2 Replies View Related

Protocols / Routing :: Sending Internet Connection Out Of Computer?

Feb 23, 2011

my desktop is picking up wirelessinternet, i have 2 avalible ethernet ports on it, is their a way i can plug an ethernet from my computer to my xbox to play online, i dont want to have a cable come from the router.

View 1 Replies View Related

Protocols / Routing :: LAN-Side Authentication At Router For Using Internet

Jan 23, 2013

Basically I have a win2000 server running as a VM in my computer with a secondary LAN address(Different subnet) which acts as a gateway for the other devices on my network (e.g. my wifi-router has DHCP relay set to my VM's address). The VM uses another network(internal NAT) for accessing the Internet though my computer. So far, I've managed to set up the DHCP and routing. Other devices on my network have access to the internet. But, since my computer has only one NIC, and even though the VM uses a secondary IP address, it's still on the same network as my internet connection. There are computers that belong to other people, who I do not want to give access through my router(even though their computers are picked up by my DHCP). I was given only one IP address for usage on my computer. This is why I wanted to add some kind of an authentication procedure(like some sort of PPPoE login maybe?)so as to prevent unauthorized usage my my connection. The question is, 'What are my options for the authentication procedure, and where do I start?' If my explanation was unclear.

View 6 Replies View Related

Protocols / Routing :: Cisco E2000 Has No Internet Connection

Mar 20, 2011

We have Linkline ADSL that was set up by them with a Netopia 2241N-006 modem and a Cisco 33674 wired router. We got a Cisco E2000 wireless router to replace the wired one. It sets up perfectly, in that I can see and connect to the wireless router just fine, but it has no Internet connection. Also, when we plug the cord straight from the modem into the computer (as was suggested by someone) it has no Internet connection, so it seems we need the Netopia modem for it work.I have connected to Cisco live chat three different times to try and find out how to make this work, and each time after making me give them all the information they insisted the uninstalling/reinstalling Cisco connect and then going through set up again it would work. On the second and third chats I even gave them the reference numbers for the previous chats so theiy could see that is what was already done, to no avail. Apparently that is the only solution they know.Then I called Cisco support on the phone (twice). The first time they insisted I hang up and I repeat the same procedure from the chats, even though I explained I had now done it three times and gave them the chat reference numbers. They said if I would not do that. The second time I called they told me that was not something they supported - using their router with an adsl modem - even though their instructions do cover it.

using the two routers together since I cannot get the wireless one to work alone. I went and bought a crossover cable, hooked the two routers LAN port to LAN port, changed the router's IP address to just outside the main router's range and disabled DHCP. This did not change anything, so I tried the one other idea I found online which was to assign the router a static IP address in the same range that the rest of the network is using, hook the two routers LAN port to LAN port with the crossover cable, and disable the DHCP. This did not work either.

View 8 Replies View Related

Protocols / Routing :: Internet Does Not Work After Changing IP Address

Jul 15, 2012

well i had the same problem because i got bored and i was like hmm i wonder if i can change my IP and i tried it and i had the same problem but when i did system restore it still did not work, now i have to get a new operateing system...

View 10 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved