Protocols / Routing :: Connect Two Asterisk Server On A HP Pro Curve 2626 Switch
Apr 11, 2013
I am trying to connect two Asterisk Server (with DHCP server enabled on both) on a HP Pro Curve 2626 switch. Server A has IP address 192.168.2.1 and Server B has IP address 192.168.3.1. I created a two new VLAN on switch, VLAN2 for 192.168.2.0 network and VLAN3 for 192.168.3.1 network. I put the command "ip routing" on the switch. My goal is to be able to ping ip address from PC 1(VLAN2) to PC 2(VLAN3) and vice versa... I'm not sure what I am missing... By the way, there is NO ROUTER involved on this set up. I tried to Google and it says HP ProCurve 2626 is a Layer 3 switch so IP routing should be possible.
I've turned up a new layer 2 WAN link between two data centres and i'm having some trouble trying to logically figure out how things should be configured.As you can see from the diagram i've created, I have the link connected on port 13 on one switch and port 14 on the other. Both ports have an IP address assigned to them and they can both ping each other..
The problem comes when I need to add routes in order to get traffic flowing over the link.I added an IP address to switch 2 on the link interface (port 14) as: 192.168.4.10
I then added an IP address to switch 1 on the link interface (port 13) as:
192.168.1.10 192.168.2.10
When I tried to add 192.168.3.10, it said "192.168.3.0 overlaps with VLAN2626". This would be correct as Vlan 2626 has an IP address of 192.168.3.15.
However, if I remove the IP address from vlan 2626 and add 192.168.3.10 to vlan 2 (the link port VLAN), I would surely lose remote access to the switch. (I'm telnetting into the switch from a machine on vlan 2626).
I started to tinker with this by manually adding a route to a server in each location and seeing if I could get traffic to flow:
On server 1: route add 192.168.4.0 MASK 255.255.255.0 192.168.1.10 METRIC 1 On server 2: route add 192.168.1.0 MASK 255.255.255.0 192.168.4.10 METRIC 1
If I try to tracert 192.168.1.20 from server 2, the first hop is the default gateway instead of 192.168.4.10.
The ultimate goal is to add the static routes to the Layer 3 router/firewall, but before I do that, I need to be sure of what to add to that router (It's a manged firewall from the data centre, so I don't have access to it and I need to raise firewall change requests to get the work done, so want to ensure it's right first time.
I want make a workgoup network with my friend by VPN.we are connected throw internet to make the VPN connection.I configed a VPN server with incoming connection. client connected to server succesfully.but sever and client havent any data send or recieve. the server dont set an ip for client.this is connection propertice: as you see there is no data sending or dara recieving..Im using ADSL Modem(tp-link 8811) and have two lan networks with Modem and another computer.
Currently, my company runs a DC and exchange server in the building. It is also hosting our website with IIS7. All AD users currently have @company1.com.au email addresses.We have just started an off shoot company and would like to setup emails in exchange so that we can automatically assign and manage emails on the same exchange server. so that each user hasWhat is the best way to do this?At the moment, company2.com - company is hosted outside with someone else. Is there a way that he can direct the mail to us so that he hosts the website but we host the email server?
I have a desktop that I have my Minecrarft Server on. It was working fine until I forwarded port 25565 to it, and now I cant use firefox or internet explorer. I can access the server from my other computer on the same network, but none of my friends can from their houses.
Recently I have faced following problem in my office, We have purchased two new Dell Server Power Edge R910 with built-in 10GB FC Network card. Service tag of this two servers are given bellow. 1. 7D94C2S 2. 6D94C2S You can can Check specification of this two server from dell website{ URL}
We have two CISCO switch and model is given bellow: Brand: CISCO Model: WS-C3560E-12SD
We want to connect server to switch through FC cable and both switch have SPF module. But when we connect server to switch, link do not establish even switch and server port light become off. Then we have tested the following things: 1. Connect server to server through FC cable, it is okay. 2. Connect switch to switch through same FC cable, it is okay.
i got a d-link router comming off modum and then a lynksys switch . well when i run the lorex program it (the switch) shows up as a router with a ip address ? i have tried a different swith but still the same thing happens .
I'm trying to set up VLANs in my network.So the first device after the internet cloud is my ISP modem/router. I don't really use the router part. The second device is my Linksys WRT54G router with DD-WRT firmware on it.Between the two, there is a subnet just for them. After the DD-WRT router, there is a subnet for my LAN.The third device is my netgear GS108T switch (with vlan support) to which almost all my computers are hooked up. One of those computers is my server that is domain controller and has the roles as shown in the image. What I would like to do is to create several virtual machines in Hyper-V. The trick is that I want to isolate them from the rest of my network. They should be able to access (and be accessed) from the internet but not the rest of my network. So my whole network should be in the same VLAN but each VM should be individually in separate VLANs.
1) I've allready created the VLANs on my Netgear Switch. I know my DD-WRT also has VLAN support. Do I need to create the same VLANs on that also?
2) How to configure the VLAN part of the Hyper-V server? (by the way, my server OS is Windows Server 2008 R2 with the hyper-v role, it's not the bare-metal hyper-v)Should my Virtual Switch be in VLAN 10 and my VMs in the other VLANs?Should the port (on the netgear switch) in which my server is connected, be in VLAN 10 (so that my server is accessible from every other computer in the network)?
I have a computer named server and it ip is 192.168.0.5 and a live ip xxxxxxxx which is a private ip. on this system my oracle middle wear is running.I just want that people may access my application which is running on 'server' through public ip. Is it possible. If it is. then how.=]
I'm setting up a Cisco 3750 layer 3 switch with several vlans. I thought enabling routing would route between the vlans, but no such luck.What I want is to share the internet access of vlan 100 with the other vlans/ip-nets.How can I do that?
i need to know that how can i make vlans in Linksys SRW224G4 Layer 2 manageable switch , because i have 100 users network having lots of users using more then 1 ip to connect 4 different servers having different ip class pools, what i need is, i want to use only single ip pool with Class B Address like 172.16.6.0 for all network users which all connect to far end servers through layer 2 Linksys SRW224G4 manageable switch controlling to allow different IP pools ? like 172.16.1.0 / 172.16.55.0 / 172.16.99.0 and 192.168.1.0
I have two different networks on same LAN.One net has public 2xx.x.x.x IPs (some on DMZ, they are servers with their own internal firewalling) and goes through a GBeth switch to a Cisco 25xx router for accessing HDSL modem with several HDSL trunks and then Internet. That router is configured to let external IPs access only DMZ IPs, of course.The other net has 192.168.x.x IPs and goes through another GBeth switch to a DLink router to access ADSL. Mainly for download traffic at a low flat cost.I would like to have a way to let the 192.x.x.x machines access the servers on the DMZ of the 2xx.x.x.x net without going outside the physical LAN. The servers host mail services and so sending heavy attached documents needs a hi-speed LAN connection and certainly not the ADSL upload capability. Not to say about servers web contents maintenance.
I have a problem, i have a DIR-620 wireless router, i can connect to wifi my both ipad and iphone but i cannot connect my laptop, even cannot access the admin page for settings, cz it seems my laptop cannot see my my network...
I am using RealVNC, have the Viewer and Server installed on three systems on my home network. I have a laptop which I am trying to use to connect to either of my two PC's, but cannot get them connected.With that being said I did have some luck with RealVNC as I have the 5900 and other ports forwarded and was able to connect with my Android tablet and Android Phone to the my two PC's and laptop with no problems....well kind of. I did have issues with this at first till I figured out I had to use a 142.*.*.* ip address because my network ip adresses were behind a NAT IP.Now back to the connecting my laptop to my two PC's issue.I have tried using the 142.*.*.* ip address and I have tried using my network ip 192.*.*.* to no avail. I just can't seem to connect.
The whole thing about IPv6 has been out for what is probably a couple of years now. But I find it very odd how even my newest modem/router can't even support it yet. Why on earth are manufacturers such as Netgear holding back so much on making their products IPv6 compatible? The IANA has just about given out what is left of the addresses, and we still have time to adapt by working our way over to IPv6 as it can work simultaneously with IPv4. Companies have been given years to prepare.
Why can't I connect to the Internet right now using IPv6? Not only is my router holding me back, but will my ISP hold me back as well?
I have a Rover system DVR 4CH with 4 CCTV camera's connected to it i want to view it through a computer stream it on the internet for free i dont want to use DYN web hosting because it cost money.
Basically, I was following instructions of how to forward a port to get higher speeds on bitcomet.After doing allsorts which I don't understand (yes, very stupid I know, but I've learned my lesson now), I restarted my computer and have since been unable to connet to the internet.
I have tried a system restore which didn't work and also searched google for hours but to no avail.When I diagnose the problem with windows,it states," "Wireless Network Connection" doesn't have a valid IP configuration.I am running Windows 7 btw.
In recent days, there was an electrical fault and my computer does not automatically connect to the wireless network in the house, since then. I do not know what happened.
I was about to portforward to be able to make an minecraft server. but i can't connect to the default gateway 192.168.1.1 so for the moment i use hamachi but i would wannt to portforward it to make it easier for others to join.
I set up the password through WPA-PSK, the problems come up. My laptop, HP G62-465DX and my Ipod Touch can connect by inputting the passcode but the other laptop in my family, HP G72-b60us, cannot connect to the router once the passcode is set up because the laptop claims that it is incompatible with the router when it was before. Also, my wireless printer HP Officejet 4500 wireless G510 n-z does not work when the passcode is set-up.
how to connect a pc to a hdtv wirelessly. The tv is to be used like a monitor. I want to display a PowerPoint file. Currently there is a lan already setup in the workplace. I have looked at some pc to tv devices but am not sure if they would work. My company's TIS department wants to put a wireless card in the workstation pc but is not sure how to connect the tv as a monitor?
For some reason, our router donwstairs was kicking one or more of our (4pc's downstairs, one occasionally upstairs) off. My son connected another router upstairs and then created a static IP for everything. It seems when he did that, our Brother 2170 wireless printer quit working. We've tried everything to get it going again and nothing works- even Brother didn't get it rectified. Earlier today, my son finally got it working, connected directly to the router to get the static IP on the printer (I guess). But when he disconnected it (hardwired) from the router, it won't work again
I have set up several types of servers on my computer (ftp, game servers, web servers, etc).
I have had a problem with people connecting to any of my servers. I know for a fact I have port forwarded correctly (I have checked 12 times, and I have never had a problem port forwarding). I know it's not my firewall, the problem persists when I completely shut it down.
I had an ftp and web server working about a week ago. No one can connect to any server, be it ftp...web...etc.
I recently am trying to get an open nat type so I can play Playstation network better. I watched a video and they told me to turn off the NAT and I did now it does not let me connect to the router page now, I can connect to the internet and stuff but I can't connect to the router page
I am trying to get my daughters laptop re-hooked to the wifi. Other computers and smart phones have no problems. This computer was connected but after the applesauce spill on the keyboard, and subsequent MicroCenter replacement of keyboard, we cannot get the laptop online.It is an Acer Aspire 5517 running Windows 7I have removed all profiles and created a new profile entering parameters from my laptop. I can see the wireless connection, but when I try to connect, I get "Windows was unable to connect to Greg". When I click troubleshoot, I get "Troubleshooting couldn't identify the problem".
I am trying to connect wirelessly to my BT Home Hub via a USB Wireless adaptor. The homehub works perfectly and I have other laptops in the house connecting via the wireless networkHowever, this is the problem. The Wireless connection status shows as good but packets only being sent and not received. Therefore when I load Internet Explorer, I get WebPage Not availableI notice that my IP address is starts with 169 and researching forums suggests that this is the problem and it should start 192? I have tried all sorts of things but simply cannot get this resolved. If I plug the HomeHub into the laptop directly, the connection via the ethernet cable works fine.
Vaio would not connect using WEP 40-bit key. Logged into Airport Extreme router with Airport setup utility for Windows from Apple. Updated firmware from 5.1.1 to 5.7. Reset Encryption from WEP to WPA/WPA2 Personal.Connected Vaio on Wifi using WPA2. Removed ethernet cable and connection was good at 54MB/s.Completed Windows Update
I had a power outage while online and when power resumed, I was no longer able to connect to the internet via my wireless router. My laptops (I have 2, work and personal) both receive the wireless signal from my router (a Linksys WRT54GC) but I get a 'DNS lookup failed' error message when trying to access the internet. My standard set up was Arris cable modem-->Linksys router-->Laptop but I've had to go cable modem-->Laptop via Ethernet in order to access the internet.
Both laptops are running WinXP Pro, SP3 and I ran 'ipconfig/all' on my work one, once when connected via Ethernet and once when I had my wireless connection enabled (but again, not connected to the internet). Results below.
Ipconfig/all when connected via Ethernet to cable modem:
Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:Documents and Settingsm03015a>ipconfig/all
