Cisco Wireless :: AP541N Connectivity And Web Management

Apr 18, 2013

we have two AP541n APs that were clustered togehter.  They are powered using PoE.  The other day I discovered one of them wasn't working properly.  I couldn't log into it from the web interface so I unplugged it and plugged it back in from the PoE switch.  That didn't work.  Since then I have taken it off the network and have tried to reset it and I still can't access it.  I've tried connecting to it from the default IP, which according to the admin guide is 192.168.10.10, and that doesn't work.  I have tried using Telnet and SSH to connect to it using the default IP and the static IP we had set for it.  I have set up a little linksys router and plugged the AP and a laptop into it in hopes it might get DHCP, but that hasn't worked either.  I have also noticed the WLAN 2.4G and WLAN 5G lights are not coming on.  The PWR, SPEED, and LAN lights all come on.  The DIAG light comes on when it's furst plugged in and then turns off.  Right now it is not plugged into PoE so that light is off too.  We had both APs plugged into an ESW-520 that was plugged into a UC560 which had recently been updated to the latest firmware: 8.6.1. The short story is I don't have any connectivity to my AP541n, even after being reset. No wireless, no Web GUI, no ping, nothing.  Has this thing become a large paperweight?

View 2 Replies


ADVERTISEMENT

Cisco Wireless :: Misconfiguration Of Management ACL On AP541N-A-K9

Nov 20, 2012

I mistakenly mis-configured "Management ACL mode" on my AP541N.
 
Administration>Administration Access Control>Managment ACL Mode
 
I set this to "Enabled", the problem is I only entered 1 IP address, and that IP address is the SAME IP as the AP's own internal interface.  I was not thinking and entered that IP out of habit when I meant to enter my workstation's IP.  The FW does not have a safeguard against this.
 
So, as you can see, this is a big problem, because now I have completely cut off all access (That I can think of) to the router.  I can never access the AP as that IP because if I set my workstation to that IP, 1) There will be an address conflict, 2) My computer won't route traffic to the AP out its NIC because it recognizes that IP as itself.

View 2 Replies View Related

Cisco Wireless :: AP541N Client Management

Apr 24, 2011

I currently have two 541N access-points slightly overlapping eaching other and my clients appear to connect to the further AP most often.  They are setup in a cluster, but that appears to just provide configuration synchronization.  Short of purchasing a wireless controller which would appear to be overkill, is there any way to manage client connections between the two AP's?

View 4 Replies View Related

Cisco Wireless :: Any Management Software Available To Manage 5 / AP541N Running Across A WAN

Sep 12, 2012

Is there any management software available to manage 5 or so AP541N running across a WAN. Eg we have a couple of VAP's setup on each access point 1 for staff and 1 for guests. I would like to be able to change all the WPA Personal guest access password centrally rather than having to log onto each box and edit it manually.

View 3 Replies View Related

Cisco Wireless :: Correct Channel Management Within AP541N Cluster

Jun 6, 2011

I have a cluster of 5 AP541Ns. I accidentally started the auto update of IP addresses based on reduction of interference, and it changed the wireless channels on all of the APs. I disabled it, but he channel settings did not change.Now if I remember correctly, before making this setting, they were all on the same channel, 6. Should they all be on the same channel? If so what setting or procedur do I have to do to get them all back on the same channel? (do I have to manually set the channel?)

View 8 Replies View Related

Cisco Wireless :: AP541n Losing Connection To Management Interface

Nov 1, 2010

I have a client with an AP541n, most recent firmware installed.  When he logs into the management interface (via IP using Google Chrome browser), it will work for a few minutes and then just disappear.   If he attempts to reload the page he gets a message similar to a website being down (page cannot be displayed).  The idle timeout has been extended to 4 hours, but this can happen at any point while logged into the interface.

View 1 Replies View Related

Cisco :: 3750x Management LAN / IP Connectivity?

Feb 6, 2013

I have created a management vlan on my network of 2950 and 3750 switches.  One 3750 has a trunk to each of the 2950 switches which includes the management VLAN.  On that 3750 the vlan and line protocol are both up even though there is no specific port assigned to the vlan; I believe the trunk connections allow the vlan line protocol to come up.  On another 3750 stack I have my VLAN defined with no ports designated or trunks; the VLAN is up however the line protocol is down.

View 12 Replies View Related

Cisco Switching/Routing :: 2950 Loss Connectivity Management Vlan?

Apr 8, 2012

Randomly when I try to access to 2950 from management tools, switch is unreachable, I have to  access from other switch and reload 2950.
 
Problem only is from managemt tool to managament vlan 1 2950.
 
The strange thing is that management interface is encountering a very fast increase of throttles, broadcast and ignored packets:
 
2950#show interfaces vlan 1
Vlan1 is up, line protocol is up
  Hardware is CPU Interface, address is 0023.3488.fd65 (bia 0023.3488.fd65)
  Internet address is xxxxxxxxxx
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255

[code]....
 
It could be  a hardware problem?, IOS has been upgraded.

View 11 Replies View Related

Cisco Wireless :: New AP541n With No SSIDs?

Feb 28, 2012

I just installed a brand new AP541N-A-K9 (running AP541N-K9-2.0(1) software) and cannot seem to add a SSID.  I've tried both from CCA and directly from the Web interface (Wireless:Wireless Network Setup menu).  The Add Another button doesn't seem to do anything.  I've even tried multiple browser versions.

View 1 Replies View Related

Cisco Wireless :: AP541N How To Configure APs

Jun 19, 2011

I have 3 AP541N. I become this not in a cluster. The APs standalone in the room. The first AP connect with cable to a DHCP Router from a other manufacturer. The other both APs should be connect over WLAN.How I must configure the APs? Which parameters must install?

View 1 Replies View Related

Cisco Wireless :: AP541N - No Access Or IP Address

Feb 12, 2013

I have 2 AP541N access points. Have been working well for a couple of years. Later last year they just dissapeard from CCA one day. COundt access them but they were still delivering 'wireless' so to speak I have recently put them back to defaults to try and get them back in to CCA. i had one, but not the other. They would work fine via GUI/web access.Then i updated them to 2.0.4 (both images) and since doing that i have no access to either of them via any form.

View 2 Replies View Related

Cisco Wireless :: AP541N Drops All Clients?

Jun 20, 2010

As I posted about in the other AP541N thread about degraded performance, mine did a strange client disconnect last week. It dropped all authenticated clients, but they all thought they were still connected. A quick disable/enable of the wireless card on the laptop would get the computer back on the AP.
 
This same thing happened again today.
 
Device information and configuration:
Device: AP541N
H/W: V01

[Code]......

View 20 Replies View Related

Cisco Wireless :: AP541N Bridge With WPA2

Aug 23, 2010

I purchased quite a few of these APs as they listed the ability to function in WPA2-PSK mode, but on initial configuration I see that this may only apply to standard AP mode?  Is there any way to configure WPA2-PSK on an AP541 to AP541 bridge?  Unfortunately, this is a must have for our client.  If not, what would allow for this with an external antenna port?

View 4 Replies View Related

Cisco Wireless :: AP541N-E-K9 Clustering And VAPs

Oct 30, 2012

I have configured two AP541N in a cluster, but only VAP0,  is listed as clustered. None of the VAPs seems to be clustered. What can I configure to get all SSIDs clustered?Product Identifier:AP541N-E-K9Hardware Version:V01Software Version:AP541N-K9-2.0(4)

View 22 Replies View Related

Cisco Wireless :: AP541N Keeps Dropping Connections

Mar 6, 2013

I have 2 AP541N's set up using a WDS bridge, broadcasting a single SSID. I am using WPA-PSK for the bridge and WPA/ WPA2 and CCMP (AES) on the SSID. I only have around 75 (Mac, PC, iPad, iPhone and Android) devices that use wireless. Some are laptops that roam around from AP to AP, and are using LAN when they are not roaming. I have increased the roaming agressiveness on PC clients and this doesn't seem to have resolved the weak connection. At most, I have 50 clients trying to access the wireless at one time. My problem is that they keep on dropping the connections and have real problems reconnecting once it's dropped. After 4 or 5 tries, they may or not be able to reconnect.

View 1 Replies View Related

Cisco Wireless :: AP541N - Computer Not Switching Between AP's

Jan 4, 2011

when moving throughout our building my laptop will not switch between AP’s unless it loses its connection with its existing AP then it will see the other AP that is closer and connect to it.
  
For example, I start at one end of the building where it connects to AP#1 at 270Mbps, if I then slowly go to another section of the building, the speed will drop all the way down to 24Mbps, but it will not switch over to AP#2 unless I turn off AP#1 then the laptop instantly switches to AP#2 at 160Mbps. Again the same behavior if I start walking back the other direction. The laptop will not disconnect from AP#2 until the signal is lost.
 
With my 2.4GHz wireless 802.11g AP’s (WAP200) I can roam around the building and the laptop will happily jump between AP’s always staying with the faster of the two available.
  
Settings are all pretty basic.
 
Mode is set to 5GHz 802.11n Channel is set to AutoA single SSID is running WPA Personal using wpa2, CCMP (AES)Channel is set to AutoChannel Bandwidth is set to 40MHzClustering is enabled and the AP’s see each other just fine. 

View 2 Replies View Related

Cisco Wireless :: Use WAP2000 As Repeater Of AP541n?

Mar 22, 2011

we want to use a WAP 2000 Box as repeater of an AP541n. Do naybody know this is possible or not?
 
Which Cisco AP boxes are compatible to act as repeater on a AP541n?

View 1 Replies View Related

Cisco Wireless :: Are There Multiple Models Of AP541N

Nov 6, 2011

We are considering order the AP541N for our network. A few questions...
 
1). Are there multiple models of the AP541N? or just one cisco part number?
 
2). I am assuming the basic antenna comes with it. If this is something that I need to buy seperate.
 
3). Are there part numbers for the POE injector? Need to know part numbers on the AP541N and the poe injectors?
 
4). We would buy a couple of these and run them in cluster mode. My understanding is that I won't need a controller. Do I need to buy a certain model to use the clustering or is that available on all the AP541N?
 
5). Can I have this talk to active directory to authenticate users? Is that tough to do? Do I need install some kind of agent on a domain controller? I have configured the ASA to use Active Directory for authentications. Should it be any more difficult that that?
 
I have setup a few other Cisco APs before and am generally familair with wireless. But, I am not a "wireless expert" and don't have any experience with this particular product.

View 1 Replies View Related

Cisco Wireless :: AP541N-K9-1.9(2) Won't Work With IPhone 3gs

Jan 3, 2011

I recently attempted to update my access points Software from AP541N-K9_1.8(0) to AP541N-K9_1.9(2).  As soon as the update and reboot were complete I could no longer connect to the wireless network using my iphone.  I switched back to the secondary 1.8 software and could immediately reconnect my iphone to the network.  Upgrading to 1.9(2) changes a setting or is flawed.

View 1 Replies View Related

Cisco Wireless :: Difference Between WAP321 And AP541N?

May 21, 2012

I was looking for some clarification on the capabilities of these devices to allow roaming of clients between AP's.  Take a basic scenario of 3 AP's and a single SSID.  I know the AP541N has clustering which uses the Fast Client Roaming Protocol, which basically does a quick re-connect to the new AP.  Not quite as seamless as using aironet and a controller, but still pretty good. 
 
Question 1 How does the WAP321 handle roaming?  Obviously without the clustering feature you would have to configure each AP independently.  But after setting them up, would it support roaming in a similiar way to the AP541N??
 
Question 2 Would running three standalone Aironet 1141's operate any differently in terms of roaming?
  
In summary I like the roaming capability of the AP541N but hate the large clunky form factor.  I need something that can be mounted in an office environment (ceilings) that will handle easy client roaming.  A short disconnect isn't a concern as long as it reconnects on it's own.   Wireless controllers are a little out of the price range for this setup.

View 3 Replies View Related

Cisco Wireless :: AP541N Very Poor Range

Aug 5, 2012

i have a 541N running the latest firmware 2.0.2.It has 3 SSIDs for the 3 vlans that it has.I have configured b/g/n.The power is fullIt is powered via POE.The end customer tells me that the range it covers is very very small!Comparing to traditional low budget APs the power is very very low.It does not cover 30-40m in free space where other APs do.Do i need to configure something more in the radio settings?

View 2 Replies View Related

Cisco Wireless :: Using AP541N As A Bridge With RV220W

Sep 25, 2011

trying to get my new router and bridge to work I am close to give up.
 
1. I have bought a RV220W router this will be connected to Internett and all wireless devices will connect to it. It seems to work fine. I have enabled on AP profile where others easyli can access internett through router WAN port
 
2. I have bought a AP541 Access point that i want to have as a bridge (We earlier used 3COM without problems) Some Computers and other stuff like printers  will be connected to this through a switch for the Ethernet port on AP541. (I dont want any clients to connect wireless to AP541N)
 
Before I start asking detailed questions, i want to verify that my setup is possible. Reading the Information on the shops webpage clearly states that AP541N can work in bridge mode, but struggling to find any good explenation makes me wonder if this really is true.

Can Cisco AP541N works as a bridge together with RV220W.

View 1 Replies View Related

Cisco Wireless :: Configure AP541N With SA520W?

Nov 8, 2011

I have an SA520W firewall, and am implementing a new AP541N. On the SA I am using port 4 to connect the AP. Trunking is on with Vlan 1 and 25. Connecting the AP I am able to use VLAN1, however when I assign a new VAP using Vlan 25, I only receive IP addresses for VLAN1.

View 1 Replies View Related

Cisco Wireless :: AP541N Can't Get AIP Address On Some Devices

May 29, 2012

I have an AP541N-N-K9 Dual Band Access Point which I'm  having some issues with. We have a few users with Android and iOS  devices and they want to connect to our corporate network but when we  configure the wireless network details in both OSs none of the devices  get an IP address. We have an MS AD/DNS/DHCP infrastructure. On looking  at the logs of the access point I can see the devices successfully  authnticating but then I see the connection being disassociated and  deauthed. A few seconds later the device attempts to get an IP address  again and the same thing happens again. This loop just keeps on going  forever. If we connect to the AP with an MS OS everything is fine. [code]

View 10 Replies View Related

Cisco Wireless :: AP541N - Dropping Clients

Jan 8, 2012

I have 3 AP541Ns setup in a small environment.  The wireless clients use laptops to attach, via RDP, to a Microsoft Terminal Server.  They need the ability to walk, with laptop, from room to room, IE roaming wireless clients.  The issue is the clients drop and re-attach constantly and takes up to 5 minutes to re-attach to the WLAN / RDP session.  Is this a symptom of going from WAP to WAP and is their anything I can do about it.

View 2 Replies View Related

Cisco Wireless :: AP541N What POE Injector Are Supposed To Be Used

Jan 30, 2011

AP541N wireless AP, what POE injector are you supposed to use?The web site states any enterprise class af POE injector will do, but the AP1131 POE injector does not work with the AP541N.

View 5 Replies View Related

Cisco Wireless :: How To Get AP541N Internet Access

Apr 10, 2013

I have a Cisco AP541N and have been attempting to configure it.  I assigned a Static IP with the Subnet, default gateway and DNS info. Everything seemed to be working fine yesterday when it was deployed.  Today, there appears to be no internet access.  We are able to connect but have limited access.

View 3 Replies View Related

Cisco Wireless :: Possible To Use External Antennas On AP541N Set In WDS Mode

Aug 20, 2010

Is it possible to use external antennas on AP541N set in WDS mode? I would only need to use 802.11g mode 54mbps.I believe that the antennas shipped with the access points are removable RP-SMA.

View 3 Replies View Related

Cisco Wireless :: Power Adapter That Can Purchase To Use With AP541N

Aug 9, 2010

Is there a power adaptor that you can purchase to use with the AP541N.

View 4 Replies View Related

Cisco Wireless :: AP541N-A-K9 Guest Access Authentication

Nov 12, 2012

I currently have two AP541N access points.  Both are configured for internal access and one unit is configured with a Guest VAP.  I want to configure the Guest VAP to redirect to an authentication page so that the user connecting has to log in to get internet access.  I'm fairly certain the AP541N doesn't offer this out of the box.  I know I can redirect, but what is needed to force a user to authenticate to gain internet access.  I want to find out what additional hardware/software I will need in order to create Guest Services of this VAP. 

View 1 Replies View Related

Cisco Wireless :: SA520W And AP541N Are Not Repeating Traffic?

Jul 15, 2010

Any AP that would be able to wrielessly repeat traffic to my SA520W (so that the AP has no ehternet wiring at all).  First off, there is no WDS option anywhere in the SA520W, so there is no method for which to simply create a WDS link between the two devices.  Yet the Factory Default Settings table in the SA520W Admin guide indicates there should be (search on WDS in the PDF to find this). both at the lack of integration of these Small Business Pro devices, and moreso at the fact that I was told that these two would be compatible for wireless-only repeating.  I've been messing around for hours trying to get something to happen.  Maybe I'm just missing something obvious as this is my first time trying to get an AP to talk wireless-only to a wireless capable internet gateway device (the SA520W).

View 4 Replies View Related

Cisco Wireless :: WDS Bridging Between AP541N And WAP4410N Incompatible?

May 19, 2012

I 've bought an AP541N & WAP4410N for the purpose to wireless(ly) bridge my TV with the Internet. The AP541N is connected to a AS5505 > Internet. My TV is connected to the ethernet port of the WAP4410N. (Also tried my laptop) I 've set WDS bridging on both APs:

- with and without encryption

- with same and different SSID and/or channel

In AP541N I can see that the WDS is up. However I cann't ping the WAP441N (hardset IP-address in same subnet as AP541N) from the AP541N. Therefore not strange that my TV/laptop doesn't get an ip-address through DHCP.
 
Although I tried this for home purposes, I gathered that if it worked it would be a nice SMB solution. I 'm a freelancer and I want to be sure that what I propose as a solution/option actually works.
 
I 've read in this forum that it might not work because of incompatible chipsets? If this is the case Cisco should mention in the datasheets so I don't waste my money or loose my credibility !

View 2 Replies View Related

Cisco Wireless :: Connect AP541N To RV220W To Use Same SSID

May 21, 2012

I would like to connect the AP541N to the RV220W and use the same SSID assigned to both throughout the office, for seemless client movement.  I would like to keep the AP541N connected via the internet cable, as it will be on a switch which is on the same segment.  The access point has many different configuration methods available, but the router appears to only have WDS as an option to connect the two devices.  I would rather not use the WDS feature on the AP, as I want to utilize as much bandwidth available as possible, and I assume using that method I would need to remove the ethernet cable from the switch.
 
Is it as simple as configuring both devices with identical VLAN settings?  I am preconfiguring the devices before installing them, as to minimize downtime, so would like to make sure the configuration is correct.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved