Cisco Wireless :: Power Adapter That Can Purchase To Use With AP541N
Aug 9, 2010Is there a power adaptor that you can purchase to use with the AP541N.
View 4 Replies
ADVERTISEMENT
Cisco Wireless :: Which Power Adapter Will Work With WAP4410
Aug 9, 2010I'd like to ask which Power over ethernet adapter will work in 100% with WAP4410 AP??
View 2 Replies View RelatedCisco Wireless :: 1602i APs - Power Injector Or Adapter?
Jan 28, 2013We are planning a wireless network using the 1602i APs. Some of our APs might or might not be within the 100m limit from the switches, so we'll be running them as repeaters instead. Right now, we are planning on buying power injectors for everything, but I can't seem to find an answer to this question:
If I'm running an AP as a repeater (no ethernet running back to a switch), can it still receive power from a power injector and a short ethernet run between the injector and the AP? Or will I need to use a power adapter?
Which Remote Support Software To Purchase For A 50+ User Base
Jan 15, 2013I am currently trying to decide on the best remote support software to purchase for a 50+ workstation business. I have experimented with Real VNC and TeamViewer, and whilst they are quite comparable I noticed that TeamViewer has a feature called "Seamless Windows" I will be providing remote support to local users, and several interstate branches - therefore the software that I decide on must accommodate a wide diversity of geographical locations.I was also looking at a product called GoverLAN, but it seems to me that GoverLAN only works on a single LAN and can't be used over a WAN in a similar way to both RealVNC & TeamViewer?
View 4 Replies View RelatedLinksys Wireless Router :: Lost Power Adapter For WRT54G
Apr 6, 2011I lost my power adapter for the WRT54G router. I have a 12V / 1000 mA brick adapter.
View 5 Replies View RelatedCisco Switches :: Power Adapter For WAP4410N?
Sep 6, 2012I would like to ask the correct part number of the power adapter on WAP4410N?
View 4 Replies View RelatedCisco Switches :: Power Adapter For SF302-08p?
Dec 27, 2012We are looking for a power adapter for a cisco switch Sf302-08p. We can't find the adapter anymore and we have to order a new one, but we can't figure out the order number of the adapter. The voltages is 48vdc and has an 4 pin connector . What is the type or ordernumber of this adapter?
View 1 Replies View RelatedWNR1000v2 - Using A Different Power Adapter For Router?
Mar 20, 2012I've lost the original power adapter that came with my wireless router (Netgear N150 Wireless Router WNR1000v2) and was wondering if it would be safe to use another power adapter with it instead. As long as the power adapter meets the the requirements of the router and fits, it should be okay to use, right? I'm just wanting to be safe before plugging it in. Don't want to damage anything.
View 1 Replies View RelatedXAVB200 Power-line Can Just Add Another Adapter
May 3, 2011I currently have a pair of NETGEAR XAVB2001-100NAS Up to 200Mbps Powerline AV 200 Adapters. Can I just add a third unit upstairs (like url...) and all three ports will have connectivity to each other?
View 2 Replies View RelatedCisco Switches :: SRW208MP AC Power Adapter Part Number
Apr 13, 2010What is the SRW208MP AC Power Adapter Part Number and where can it be ordered from ?
View 11 Replies View RelatedConnecting TPLink Powerline Adapter To Power Strip?
Sep 28, 2012I will be purchasing the AV200 powerline kit from Tp-link and want to know whether there will be any issues in connected them through either a power strip or double adapter?
View 8 Replies View RelatedCisco Switching/Routing :: 892 Power Adapter Orderable Part Number
Jul 29, 2012What is the orderable part number of Cisco 892 series routers.
View 1 Replies View RelatedLinksys Wired Router :: BEFSR81 V2 - Power Adapter Required
Jun 2, 2012From what I understand, it requires a 5V 2.5A adapter ... alas, cannot find one.
View 2 Replies View RelatedXAVB101 Netgear Power-line Adapter Not Working With AMD Llano HTPC
Jan 3, 2012I have a NETGEAR XAVB101 Powerline AV Ethernet Adapter and an AMD Llano build HTPC which refuses to work with each other.
The power plug works well with my Gateway NV79 laptop and even my Intel Core i5 -2500K desktop, without any problems! I have also used it to connect to my Roku, Yamaha Network Receiver and other networked stuff and all worked great, just the HTPC seems to have issues connecting to the network!
The HTPC is AMD A6-3650 on a ECS FM1 A75 Mobo with Integrated Realtek RTL8111E Gigabit Ethernet Controller, which is what I am connecting the power plug to! Only the connection over the power line adapter does not work, it works great with both a connection directly from the router and with wireless!
The adapter has a 128 bit encryption push button security feature which I'm NOT using. When I connect it the HTPC tries to connect and fails and shows the network as connected to an unidentified network. My LAN drivers on the computer is all up-to-date!
Cisco Wireless :: 1252 - WCS Reports AP Draws Low Power - With Correct Power Injector
Jul 21, 2011I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
Cisco Wireless :: New AP541n With No SSIDs?
Feb 28, 2012I just installed a brand new AP541N-A-K9 (running AP541N-K9-2.0(1) software) and cannot seem to add a SSID. I've tried both from CCA and directly from the Web interface (Wireless:Wireless Network Setup menu). The Add Another button doesn't seem to do anything. I've even tried multiple browser versions.
View 1 Replies View RelatedCisco Wireless :: AP541N How To Configure APs
Jun 19, 2011I have 3 AP541N. I become this not in a cluster. The APs standalone in the room. The first AP connect with cable to a DHCP Router from a other manufacturer. The other both APs should be connect over WLAN.How I must configure the APs? Which parameters must install?
View 1 Replies View RelatedCisco Wireless :: AP541N - No Access Or IP Address
Feb 12, 2013I have 2 AP541N access points. Have been working well for a couple of years. Later last year they just dissapeard from CCA one day. COundt access them but they were still delivering 'wireless' so to speak I have recently put them back to defaults to try and get them back in to CCA. i had one, but not the other. They would work fine via GUI/web access.Then i updated them to 2.0.4 (both images) and since doing that i have no access to either of them via any form.
View 2 Replies View RelatedCisco Wireless :: Misconfiguration Of Management ACL On AP541N-A-K9
Nov 20, 2012I mistakenly mis-configured "Management ACL mode" on my AP541N.
Administration>Administration Access Control>Managment ACL Mode
I set this to "Enabled", the problem is I only entered 1 IP address, and that IP address is the SAME IP as the AP's own internal interface. I was not thinking and entered that IP out of habit when I meant to enter my workstation's IP. The FW does not have a safeguard against this.
So, as you can see, this is a big problem, because now I have completely cut off all access (That I can think of) to the router. I can never access the AP as that IP because if I set my workstation to that IP, 1) There will be an address conflict, 2) My computer won't route traffic to the AP out its NIC because it recognizes that IP as itself.
Cisco Wireless :: AP541N Drops All Clients?
Jun 20, 2010As I posted about in the other AP541N thread about degraded performance, mine did a strange client disconnect last week. It dropped all authenticated clients, but they all thought they were still connected. A quick disable/enable of the wireless card on the laptop would get the computer back on the AP.
This same thing happened again today.
Device information and configuration:
Device: AP541N
H/W: V01
[Code]......
Cisco Wireless :: AP541N Connectivity And Web Management
Apr 18, 2013we have two AP541n APs that were clustered togehter. They are powered using PoE. The other day I discovered one of them wasn't working properly. I couldn't log into it from the web interface so I unplugged it and plugged it back in from the PoE switch. That didn't work. Since then I have taken it off the network and have tried to reset it and I still can't access it. I've tried connecting to it from the default IP, which according to the admin guide is 192.168.10.10, and that doesn't work. I have tried using Telnet and SSH to connect to it using the default IP and the static IP we had set for it. I have set up a little linksys router and plugged the AP and a laptop into it in hopes it might get DHCP, but that hasn't worked either. I have also noticed the WLAN 2.4G and WLAN 5G lights are not coming on. The PWR, SPEED, and LAN lights all come on. The DIAG light comes on when it's furst plugged in and then turns off. Right now it is not plugged into PoE so that light is off too. We had both APs plugged into an ESW-520 that was plugged into a UC560 which had recently been updated to the latest firmware: 8.6.1. The short story is I don't have any connectivity to my AP541n, even after being reset. No wireless, no Web GUI, no ping, nothing. Has this thing become a large paperweight?
View 2 Replies View RelatedCisco Wireless :: AP541N Bridge With WPA2
Aug 23, 2010I purchased quite a few of these APs as they listed the ability to function in WPA2-PSK mode, but on initial configuration I see that this may only apply to standard AP mode? Is there any way to configure WPA2-PSK on an AP541 to AP541 bridge? Unfortunately, this is a must have for our client. If not, what would allow for this with an external antenna port?
View 4 Replies View RelatedCisco Wireless :: AP541N-E-K9 Clustering And VAPs
Oct 30, 2012I have configured two AP541N in a cluster, but only VAP0, is listed as clustered. None of the VAPs seems to be clustered. What can I configure to get all SSIDs clustered?Product Identifier:AP541N-E-K9Hardware Version:V01Software Version:AP541N-K9-2.0(4)
View 22 Replies View RelatedCisco Wireless :: AP541N Keeps Dropping Connections
Mar 6, 2013I have 2 AP541N's set up using a WDS bridge, broadcasting a single SSID. I am using WPA-PSK for the bridge and WPA/ WPA2 and CCMP (AES) on the SSID. I only have around 75 (Mac, PC, iPad, iPhone and Android) devices that use wireless. Some are laptops that roam around from AP to AP, and are using LAN when they are not roaming. I have increased the roaming agressiveness on PC clients and this doesn't seem to have resolved the weak connection. At most, I have 50 clients trying to access the wireless at one time. My problem is that they keep on dropping the connections and have real problems reconnecting once it's dropped. After 4 or 5 tries, they may or not be able to reconnect.
View 1 Replies View RelatedCisco Wireless :: AP541N - Computer Not Switching Between AP's
Jan 4, 2011when moving throughout our building my laptop will not switch between AP’s unless it loses its connection with its existing AP then it will see the other AP that is closer and connect to it.
For example, I start at one end of the building where it connects to AP#1 at 270Mbps, if I then slowly go to another section of the building, the speed will drop all the way down to 24Mbps, but it will not switch over to AP#2 unless I turn off AP#1 then the laptop instantly switches to AP#2 at 160Mbps. Again the same behavior if I start walking back the other direction. The laptop will not disconnect from AP#2 until the signal is lost.
With my 2.4GHz wireless 802.11g AP’s (WAP200) I can roam around the building and the laptop will happily jump between AP’s always staying with the faster of the two available.
Settings are all pretty basic.
Mode is set to 5GHz 802.11n Channel is set to AutoA single SSID is running WPA Personal using wpa2, CCMP (AES)Channel is set to AutoChannel Bandwidth is set to 40MHzClustering is enabled and the AP’s see each other just fine.
Cisco Wireless :: Use WAP2000 As Repeater Of AP541n?
Mar 22, 2011we want to use a WAP 2000 Box as repeater of an AP541n. Do naybody know this is possible or not?
Which Cisco AP boxes are compatible to act as repeater on a AP541n?
Cisco Wireless :: Are There Multiple Models Of AP541N
Nov 6, 2011We are considering order the AP541N for our network. A few questions...
1). Are there multiple models of the AP541N? or just one cisco part number?
2). I am assuming the basic antenna comes with it. If this is something that I need to buy seperate.
3). Are there part numbers for the POE injector? Need to know part numbers on the AP541N and the poe injectors?
4). We would buy a couple of these and run them in cluster mode. My understanding is that I won't need a controller. Do I need to buy a certain model to use the clustering or is that available on all the AP541N?
5). Can I have this talk to active directory to authenticate users? Is that tough to do? Do I need install some kind of agent on a domain controller? I have configured the ASA to use Active Directory for authentications. Should it be any more difficult that that?
I have setup a few other Cisco APs before and am generally familair with wireless. But, I am not a "wireless expert" and don't have any experience with this particular product.
Cisco Wireless :: AP541N-K9-1.9(2) Won't Work With IPhone 3gs
Jan 3, 2011I recently attempted to update my access points Software from AP541N-K9_1.8(0) to AP541N-K9_1.9(2). As soon as the update and reboot were complete I could no longer connect to the wireless network using my iphone. I switched back to the secondary 1.8 software and could immediately reconnect my iphone to the network. Upgrading to 1.9(2) changes a setting or is flawed.
View 1 Replies View RelatedCisco Wireless :: Difference Between WAP321 And AP541N?
May 21, 2012I was looking for some clarification on the capabilities of these devices to allow roaming of clients between AP's. Take a basic scenario of 3 AP's and a single SSID. I know the AP541N has clustering which uses the Fast Client Roaming Protocol, which basically does a quick re-connect to the new AP. Not quite as seamless as using aironet and a controller, but still pretty good.
Question 1 How does the WAP321 handle roaming? Obviously without the clustering feature you would have to configure each AP independently. But after setting them up, would it support roaming in a similiar way to the AP541N??
Question 2 Would running three standalone Aironet 1141's operate any differently in terms of roaming?
In summary I like the roaming capability of the AP541N but hate the large clunky form factor. I need something that can be mounted in an office environment (ceilings) that will handle easy client roaming. A short disconnect isn't a concern as long as it reconnects on it's own. Wireless controllers are a little out of the price range for this setup.
Cisco Wireless :: AP541N Very Poor Range
Aug 5, 2012i have a 541N running the latest firmware 2.0.2.It has 3 SSIDs for the 3 vlans that it has.I have configured b/g/n.The power is fullIt is powered via POE.The end customer tells me that the range it covers is very very small!Comparing to traditional low budget APs the power is very very low.It does not cover 30-40m in free space where other APs do.Do i need to configure something more in the radio settings?
View 2 Replies View RelatedCisco Wireless :: Using AP541N As A Bridge With RV220W
Sep 25, 2011trying to get my new router and bridge to work I am close to give up.
1. I have bought a RV220W router this will be connected to Internett and all wireless devices will connect to it. It seems to work fine. I have enabled on AP profile where others easyli can access internett through router WAN port
2. I have bought a AP541 Access point that i want to have as a bridge (We earlier used 3COM without problems) Some Computers and other stuff like printers will be connected to this through a switch for the Ethernet port on AP541. (I dont want any clients to connect wireless to AP541N)
Before I start asking detailed questions, i want to verify that my setup is possible. Reading the Information on the shops webpage clearly states that AP541N can work in bridge mode, but struggling to find any good explenation makes me wonder if this really is true.
Can Cisco AP541N works as a bridge together with RV220W.
Cisco Wireless :: Configure AP541N With SA520W?
Nov 8, 2011I have an SA520W firewall, and am implementing a new AP541N. On the SA I am using port 4 to connect the AP. Trunking is on with Vlan 1 and 25. Connecting the AP I am able to use VLAN1, however when I assign a new VAP using Vlan 25, I only receive IP addresses for VLAN1.
View 1 Replies View RelatedCisco Wireless :: AP541N Can't Get AIP Address On Some Devices
May 29, 2012I have an AP541N-N-K9 Dual Band Access Point which I'm having some issues with. We have a few users with Android and iOS devices and they want to connect to our corporate network but when we configure the wireless network details in both OSs none of the devices get an IP address. We have an MS AD/DNS/DHCP infrastructure. On looking at the logs of the access point I can see the devices successfully authnticating but then I see the connection being disassociated and deauthed. A few seconds later the device attempts to get an IP address again and the same thing happens again. This loop just keeps on going forever. If we connect to the AP with an MS OS everything is fine. [code]
View 10 Replies View Related