Cisco Wireless :: Local Printers Not Working With 2504 WLC?
Nov 20, 2012
I have a 2504 WLC with 3 1262 WAPs in lightweight mode.
Clients connect using WPA2 PSK AES with no problem. Clients are Windows XP Home SP3. Test pages end up in print queue and eventually get a error printing status. Clients are not part of a domain and in a standalone workgroup - techstream.
Printer can be pinged from wireless client.
Another 1262N WAP in standalone mode connected to same lan from windows 7 sp1 clients have no problem printing to a local printer.
What does work on the Windows XP Home client is connecting to a network shared printer authenticating with domain admin id and password and it works. Reboot and the network shared printer can not connect multiple reasons are "access is denied" and message box says "only security tab will be displayed....." Another Windows XP Home SP3 client on reboot can't open the network shared printer with message "Can't find printer"
The local printers do work on these pc's with an old colubris router that has an outside interface on our lan and internal network with clients getting dhcp address from colubris router of 192.168.3.XXX .
What is wrong with the wireless 2504 WLC?
View 4 Replies
ADVERTISEMENT
Sep 5, 2012
I have walked into a company that has several small (1-4 PC's each) remote locations, and they all connect to Terminal Server to use our POS app. This app will not keep redirected printers saved between each session, so in order to save the printers, they have software VPN's set up on each client, then the local printers are installed on the server through a Local Port using the VPN ipaddressprinter share name. This allows the printers to be saved in the program and not re-assigned each session. Now, let's say that I have implemented a new desktop replacement procedure, and we are now in phase one of said procedure. I have purchased Windows 7 64-bit desktops. After setting up my deployment standards and testing in-house, I placed one of these PC's in the field. This is where I learned the issues of printing from a 32-bit server to a 64-bit client. I have not been able to successfully print to the printer installed on the server using the Local Port of the client, print job errors out. I have done some research, and found the issues with printing from 32-bit to 64-bit, and have installed all the additional drivers I can find, with no success.
View 1 Replies
View Related
Jan 16, 2012
how can i add two printers of different hp series to the same local network ?
View 1 Replies
View Related
Mar 3, 2012
I have a home network running all Mac computers (though can run Windows VM if necessary) and a pair of USB printers. The wireless router and cable modem are in one room, but the printers are in another. I'd like to find the most practical way to add the printers to the local wireless network without sharing them from a computer. I've tried that for a while, but don't want to leave a laptop connected 24/7 just to enable wireless printing (rather defeats the purpose of a portable computer). I don't have any wired network lines in the home, and am not excited by the idea of running any cables.
View 5 Replies
View Related
May 29, 2012
Is it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC
View 1 Replies
View Related
Mar 25, 2013
setup a DHCP server on a WLC 2504. I'll try to resume my configuration:
I have 2 networks: inside users (vlan 1) and external users (vlan)
My controller uses the port 1 to connect to the switch, which has a trunk with WLC.
I have two routers, one using vlan 1 (192.168.3.0/24) and one using vlan 10 (200.X.X.X). All ports to these routers are access ports on their respective vlans.
I have 2 SSID, one for inside, other to outside. Inside is working very well.
To the outside I created a DHCP escope and already set the IP of the management interface 192.168.3.119.
Managemente interface (vlan 1 inside): 192.168.3.119/24
Outside interface (vlan 10): 200.X.X.195 - Default gateway 200.X.X.X.193
I alredy checked the DHCP Proxy in Advanced option.
See the output of the debug client:
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
[Code].....
View 3 Replies
View Related
Mar 17, 2013
CAP3501 + Cisco 2504 controller, not working MESH? So it should be, or what I am doing is not correct.
View 7 Replies
View Related
May 12, 2011
my computer is custom made and it has been running just fine until recently. Usually when turn on my computer and login, my computer is connect to the internet. However recently I have not been able to connect with the local area connection and i'm currently on wireless connection. When i'm not using wireless my internet doesn't connect and I can't check my router by typing 192.168.1.1. I have a Linksys WRT54G and i'm using Vista SP2. I don't like using wireless at all and I want my connection to go back to normal[CODE]
View 9 Replies
View Related
Jul 9, 2012
I thought that you're supposed to be able to type myrouter.local in order to get to the router BIOS. It does not work for me; instead it generates a Google search. Is there a way to get that to work?
View 5 Replies
View Related
Sep 12, 2011
I added a new wireless printer and a laptop to a wireless network for a friend but I just found out the original laptop can not print to it's wireless printer. Do you know how you know how to connect two wireless printers to one wireless router.
View 2 Replies
View Related
May 4, 2011
we have using 10 system with domain contorller connected to network once disconnect server i cant acces to local systen ( per to per )
View 1 Replies
View Related
Feb 28, 2012
I have a weird issue. I recently setup an ASA 5510 and had SSH working. To make it easier on my VPN users I then decided I wanted to setup a Windows 2008 Network Policy Server for RADIUS authentication. Ever since I added the RADIUS part to aaa authentication, when I use SSH to connect to the ASA it will not take the local user name and password I have setup. I can however get in using a Domain user name and password. Below is the SSH and AAA configuration. Am I missing something here? The username and password in the ASA is not on the domain and it's like the ASA is not even trying LOCAL when it tries to authenticate. I want it to use the local username and password if possible. I'm kind of new to ASA's..
On another note, I have never been able to SSH in on the internal interface. I always get a "The remote system refused the connection" error message. I can only use the outside interface.
Site-ASA# sh run | in ssh
aaa authentication ssh console SERVER_RADIUS LOCAL
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 inside
ssh timeout 60
[code]....
View 2 Replies
View Related
Sep 12, 2011
I added a new wireless printer and a laptop to a wireless network for a friend but I just found out the orginal laptop can not print to it's wireless printer. Do you know how you know how to connect two wireless printers to one wireless router.
View 3 Replies
View Related
Jan 9, 2013
Region : Others
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I got a TL-WR842ND to try and decide if i want to buy it. I want to connect a usb hub with 5 printers connected to that hub and use it as print server, would that work at all?
View 2 Replies
View Related
Jun 10, 2011
Will all usb printers be able to connect to the e3200 by usb with the firmware update? If not, what printers will be supported?
View 9 Replies
View Related
Nov 6, 2012
The wireless Internet at home is not working on my laptop anymore. It's working fine on my mobile as well as with other wireless networks at school for example. No matter what browser I use I usually dont get to any website. Most of the time it says access: local only, or local and internet, or limited connectivity. If I'm lucky at the right time I can open a website but then it's gone again.
View 13 Replies
View Related
Feb 26, 2012
I need to configure a network in 1 small office space that segregates 2 company domains but allows them to share an Internet connection, a WAP, a couple of printers, and a non-Cisco VoIP phone system. And, it needs to provide guest access to the internet and printers via wireless. I have a SG300-28P, an SA520W, and a WAP2000 to make it all happen. [code]
View 3 Replies
View Related
Apr 22, 2012
i'm trying to setup a local DNS server to manage small office local-only domain names for our servers. i have the DNS working properly (resolving local machines and using the ISP dns if it can't). so i put the DNS server ip into the "Static DNS 1" field of the router settings. the other 2 static dns fields are empty.the problem is that the router is still using the ISP dns server as the primary and my local dns server as the secondary. i verify this in two places. first, if i go to the "status" tab, DNS 1 shows the ISP server while DNS 2 shows my local DNS server. secondly, if i connect to the wireless device with a linux-based machine, the /etc/resolv.conf file shows the nameserver ips in the same incorrect order.
View 1 Replies
View Related
Jan 26, 2012
Had the following network (fully functional) for last 3 years: Modem (netopia dsl 192.168.1.254) router (linksys wrt54gs 192.168.1.1) WAP1 (linksys wrt54g2 192.168.1.250) and WAP2 (Linksys wrt54g2).I was always able to click on Devices and Printers in Win 7 and would see the equipment displayed.I could also access the router and wireless access points by typing their address in my browser. The modem failed after 5 years.I purchase a new Netgear N300 ADSL2+Modem Router (DGN2200)and replaced the failed modem and attached router.I made no changes to either WAP's.Everything works just fine (after about 30 minutes on phone with Netgear Tech to configure), but now none of the equipment displays in Devices and Printers. Also, I cannot connect to either WAP by typing their address in browser.I can see the Netgear device when I click on "network" in file manager.It displays a model number and is labeled a "gateway".
I'm just curious as to why I am no longer able to "see" or access the devices. Looks like I would have to actually pull the WAP's and connect to them directly if I needed to change their configurations.
View 1 Replies
View Related
May 9, 2012
I have a Comcast SMC8014 cable modem connected to a Linksys BEFSR81 Router and a Netgear Prosafe 24-port 10/100 switch connected to one of the LAN ports on the router. There are many PCs connected to this network, including one used as a file server. I would like to add a LINKSYS WRT54GL wireless router to this mix to allow visitors wireless access to the internet and network printers but NOT allow access to the file server
View 7 Replies
View Related
Jun 18, 2008
I have a linksys wrvs4400n router on which:The wireless computers are connected to the home network (v lan 1)Port 1 is connected to the home network (v lan 1)Port 2 is connected to the office network (v lan 2)And the printers are connected to port 3.Now I'd like to setup the router in such a way that all computers have access to the printers (port 3), but I don't know what v lan settings I have to use on port 3, or if it is even possible...
View 5 Replies
View Related
Aug 12, 2011
I am working to find a new printer on a network. The new printer has the exact same name as another printer in the network? How do I assign a PC to default to the correct printer. It is a very active office so the trial an error thing sometimes takes a long time and also is frustrating because every time I install a new PC to the network (which is often) I run into the same problem over and over again. So how to I get the IP Address of the networked printer? How do I use the IP Address when assigning a new computer?
View 3 Replies
View Related
Sep 2, 2011
Client who owns a school (small pre-school) has 3 desktops that she uses in the office and wants to be able to print to 3 different printers. So each desktop has the ability to print to each of the 3 printers. Her reason for 3 different printers are if one is out of ink I can print to another, or if one just isnt working I can print to another. Would I use a USB switch(assuming they connect via USB)
View 7 Replies
View Related
Aug 22, 2012
I am configuring a few new computers for an office and I would like to rename the printers we have here. There are 2 printers at the front desk that have confusing combinations of numbers and letters for names and I would like to name them something like "front desk color" or "front desk b&w". These computers are connected to a network and accessable from 10+ computers.
View 1 Replies
View Related
Dec 9, 2012
We are doing a new installation of a Cisco ACS 5.4 replacing a Microsoft NPS.
Recently I ran into issues with Lexmark wireless printers authenticating against the ACS 5.4.
While these printers work against the old Microsoft NPS we want to replace, I get "11500 Invalid or unexpected EAP payload received" on the ACS.
Windows/Android/iDevices authenticate against the same SSID using PEAP. I suspect, we ran into
CSCtq46211 Bug Details
Lexmark Printers work with ACS 4 but not ACS 5 Symptom: Lexmark printers uzed to work with ACS 4.2 but they produce "internal error" on acs 5.1 or 5.2
Conditions: Not known exactly
Workaround:1st Found-In 5.2(0.26.3)
Fixed-In 5.3(0.40.7)
setting up a new VM with ACS 5.3 patching it to P7, reconfiguring and retest all the stuff we implemented during several days ist not an option.
The Cisco TAC refuses to open a SR because the product is under warranty only, and claims warranty only covers HARDWARE replacement... (and we ordered ACS is a VM,,,) Maybe I should burn the ISO image to a DVD and RMA it for repair .
Maybe Cisco could verify whether the fix for CSCtq46211 has been integrated to ACS Version 5.4.0.46-B.221 already or not ?
View 1 Replies
View Related
Aug 3, 2011
I have several networked printers in my office. Two users stopped being able to print today to any of the networked printers. Everything else works fine. I have tried everything I can think of
View 1 Replies
View Related
Mar 28, 2012
I'm running a VB Script from the logon script to add printers when users log on.The Colour printer is added no problem but the black and white printer was working but now wont.The print share names are correct and the server name is correct.
View 2 Replies
View Related
Jan 24, 2012
I am having trouble with my network, specifically printer and file sharing. I have 3 computers, (2 wired, 1 wireless) The network hasn't worked for quite a while. I just hooked up a new (wired) computer and it won't work on the network either. With the wireless computer, if I click on "view workgroup computers" I can see all the computers but cannot access them. With the 2 wired computers, I always get the message, "MSHOME is not accessible," etc. Funny thing is, the network used to work. I don't know what happened to it. I just formatted this new wired computer and loaded XP on it, used the network setup wizard, but keep getting the "not accessible" message. However, last month, I was working on my mom's computer and I put it on my network (hardwired). I had just formatted it and put XP on it and with that computer, I was able to access the laptop computer through the network.I have tried several times to create a new network by using the network setup wizard but it keeps saying that MSHOME is unavailable.I am using XP service pack 3 on all computers, Zone Alarm on 2 of the computers (the router and the new computer), and Windows Firewall on the other wired computer. I can access the Internet with all 3 computers.
View 18 Replies
View Related
Feb 11, 2011
I understand we cannot view computers that in different workgroup though in the same network. But when I try to add printer it lists even those local printers that is attached and shared in different workgroup.
View 1 Replies
View Related
Jan 3, 2013
I am trying to get an XP machine to communicate with 2 printers that are wired via USB to a windows 7 machine. Peachtree accounting is running on both machines and the windows 7 machine holds all the data this works fine but when I try to share the printers I can not. When I go into the window 7 Home Prem. network share and choose to allow printer and file shareing and close out the window cut off the computer reboot and go back into file and printer shareing both are in the off position what's up?
View 6 Replies
View Related
Mar 2, 2011
My Dell laptop cannot see any of my printers on my network. I recently installed a new Linksys 160N Router and created a new network on my desktop which runs Windows 7. These are the three computers I have:
HP Desktop - Windows 7
Dell Inspirion 600m Laptop - Windows XP
Compaq Desktop - Windows NT
Prior to installing the new router, all computers could see each other on the network.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows XP Home Edition, Service Pack 2, 32 bit
Processor: Intel(R) Pentium(R) M processor 1.60GHz, x86 Family 6 Model 13 Stepping 6
Processor Count: 1
RAM: 1023 Mb
Graphics Card: ATI MOBILITY RADEON 9000, 32 Mb
Hard Drives: C: Total - 72794 MB, Free - 48125 MB;
Motherboard: Dell Computer Corporation, 0X8957, , .D1XM981.CN4864358I4849.
Antivirus: Norton 360, Updated: Yes, On-Demand Scanner: Enabled
View 3 Replies
View Related
Oct 17, 2011
I am trying to find the file where I can edit what printers show when looking for network printers in Server 2008. In 2003 server is was the NTPRINT.inf, where you can edit what printers populate but in server 2008 I cannot edit this file. Can this be done in Server 2008?
View 1 Replies
View Related
Mar 21, 2011
I added a VOIP fax line to my network and in doing so, was forced to reset my router, as it would not go on-line. Now the printers are all off line and I can not get them back online. I followed instructions within admin and it did not work. My network is a 2 computer network. My computer acts as server and then one other computer.
View 2 Replies
View Related
