Cisco :: Getting Alert In WCS 7.0.172.0 - DoS / CTS Flood

Dec 12, 2011

I have WCS 7.0.172.0 where as i have very frequent alert about DoS : CTS flood In channel 60, the system has detected 212 CTS frames in the last minute, which matches the traffic pattern of the form of denial-of-service attack, CTS (Clear-To-Send) attack. A wireless denial-of-service attacker may suspend the wireless media for communication by taking advantage of the privilege of CTS frame to reserve RF medium for transmission. By transmitting back to back CTS frames, an attacker can force other wireless devices sharing the RF medium to hold back its transmission until the attacker stops transmitting the CTS frames. The system detects the abuse of CTS frames for denial-of-service attack.  

View 2 Replies


ADVERTISEMENT

Servers :: How To Block IP User Not To Flood Chat Room

Feb 4, 2011

I have an chat room and have a problem with 2 chatter who keep on flooding my room. I need a good mode to set for me to Bann then life and all my modes I am using its not good and they keep on coming back with their IP or fake ip users

View 2 Replies View Related

Cisco Firewall :: ASA5510 Or 5520 Can Protect DDos Attack And Sync Flood

Sep 3, 2010

Does Cisco ASA5510 or 5520 can protect DDos attack and sync flood ?I have problem on this, so how can i protect on this, some time i saw on my log like this"sync flood " or "ddos to xxx.xxx.xxx.xxx" the ip address random .

View 7 Replies View Related

Cisco Switching/Routing :: Unicast Flood On 3750 - How To Determine Source MAC Address

Feb 27, 2013

There is a unicast flood on 3750 killing slow modem links. How to determine source MAC address of flooder? Is there a rate limit feature for it?
 
I know how to block it completely on port-level, but it breaks normal network operation. (when port goes down for some reason, it's learned MACs got flushed and since other hosts know MACs, they keep flooding untill their arp caches expire).

View 11 Replies View Related

To Get Security Alert From Cisco

Apr 10, 2012

I would like to receive Cisco's email alert for bugs, security vulnerability, etc. if there is such service.

View 3 Replies View Related

Cisco :: Lms 4.2 Interface Down Alert

May 5, 2012

I receive email when an interface comes  down but because i have a lot of routers with a lot of interfaces i can' tell which one came down , is there any way to include the description under the interface in the email ?
 
Also can i monitor  the existence/not of specific  route in the routing table and receive email ?

View 2 Replies View Related

Cisco :: LMS 4.2 Critical Alert In Email?

Jan 31, 2013

I have an issue with my lms 4.2 installation.I have created a fault notication group which sends me an email when an alert is active on a device.Some of the devices are deleted from the inventory, but when I restart my deamon manager. I receive alerts for all the devices I have deleted in the past.I get this email in my inbox.When I check "Monitor - SNMP traps - fault notification group" I can't see any of the devices for which I receive the email alert? 
 
EVENT ID                = 00024PS
TIME                    = Fri 01-Feb-2013 11:03:59 CET
STATUS                  = Active
SEVERITY                = Critical
MANAGED OBJECT          = switch
MANAGED OBJECT TYPE     = Switches and Hubs

[code]....

View 2 Replies View Related

Cisco :: SCE1010 Alert Not Enough Disk Space

Apr 14, 2013

My SCE1010 show the alert "Not enough disk space" in log.I find old discuss , someone say can delete the file: /tffs0/SYSTEM/PREVDBG.TXT , because the file is too big.But I don't confirm  delete the file will not effect system work fine. [code]

View 8 Replies View Related

Cisco Wireless :: WAP321 - Email Alert Blank

Mar 27, 2013

I have a WAP321 here, which is running at firmware version 1.0.3.4. The E-Mail Alert setup works for me, meaing I receive notification E-Mails from the Access Point. I am wondering however, why those E-Mails are blank, meaning, I only receive header information (to, from, date, subject) but no body content. I was expecting to receive the error message as content of the E-Mail Alert.

View 5 Replies View Related

Cisco Firewall :: Does ASA 5500 Have Email Alert Function

Oct 7, 2012

If asa finds the abnormal behavior, can set up and send email to administrative mailbox?

View 6 Replies View Related

Cisco :: 3845 Router - DFM 3.0.2 False Alert On E1 Controller

Jul 20, 2011

I have the following problem with DFM 3.0.2:
 
One of my customers has got a Cisco 3845 router with some E1 controllers in it. DFM sometimes generates an alert that says the controllers are flapping, meanwhile there is no syslog, or snmp-trap generated in the router itself. If the cables disconnected/connected, or a shut/no shut command was issued ont the interfaces, the router generates the syslog and snmp-trap as it is required.
 
So in a nutshell it seems that there is no flapping ont the controller, but for some reason DFM thinks that there was one.
 
I searched for bugs, but wasn't be able to find anything relevant neither in DFM, nor in the IOS itself (c3845-advsecurityk9-mz.124-24.T2.bin)

View 2 Replies View Related

Cisco Firewall :: ASA 5520 Email Alert Configuration

Apr 26, 2010

I am trying to setup email alert on our ASA 5520 so that i can receive emails to my exchange account below is the configuration [code] The smtp server is in our internal network.first i am not able to ping 172.17.1.12 as ping is blocked.i did this confgi like two days before..but ca see alerts and error messages through asdm but no mail is  coming in.

View 5 Replies View Related

Cisco :: LMS 4.1 Email Alert When Stack / Switch Not Responding

Oct 31, 2012

With LMS 4.1.How do i create an Email alert when stack/switch become non responsive?

View 1 Replies View Related

Need Software To Get Alert If User Installing Any Program

Mar 3, 2011

Is there a software out there, that will send me an alert when a user is installing a program on there computer? Whether is sends me an email or a text, really dont care. I have a guy in one of our remote locations that likes to install his own IT Tools on everyone's computer and i need to know when he is doing this.

View 1 Replies View Related

Limited Or No Connectivity Alert When Connected Through Router?

Feb 18, 2013

I connected my desktop with n300netgear -router. It was working fine until I reset it.After that I am facing this problem of not able to access internet. It shows limited or no no connectivity. But when I plug the internet cable directly to my desktop its working fine. When I connect it via router.

C:Documents and Settings
agaraj>ipconfig /all

Windows IP Configuration[code].....

View 7 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.3 - Active Sessions Are Over Limit Email Alert

Aug 19, 2012

I have recently enabled the SMTP alert function in ACS 5.3. It seems to work well for most of the alerts. One thing though, the active sessions are over limit warning that comes up every so often. I know it is not impacting operations and it is ACS's way of clearing out sessions that had no accounting stop, but how do I disable this alert from being sent by e-mail from ACS 5.3?

View 3 Replies View Related

Cisco Switching/Routing :: ASR 1001 False Environmental Alert

Dec 18, 2011

I have a few new ASR 1001s throwing false environmental alerts.According to the logs, the inlet temp is in excess of 100 degrees C.When I telnet to the routers, they're well within tolerance (30-32C),Running 15.1(1)S and bug toolkit shows no related issues or caveats.

View 1 Replies View Related

Cisco Switching/Routing :: Memory Status Alert Logs On Nexus 7K?

Mar 22, 2012

Below memory status alerts of are seen on our syslog server for Nexus 7K switch(Default VDC).
 
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : CRITICAL ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : MINOR ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : SEVERE ALERT RECOVERED
 
Memory threshold Not created on Nexus. Can we ignore this alert or does it impact our current network traffic?

View 5 Replies View Related

Cisco VPN :: ASA 5505 - AnyConnect 3.1 Captive Portal False Alert Stops Users Connecting?

Dec 29, 2012

I am having problems with a customer's ASA 5505 with Anyconnect 3.1 - it is generating captive portal false-alerts which are stopping users from connecting. This issue began when I upgraded from Anyconnect 2.4 to 3.1, and it appears like this: A user downloads and installs the Anyconnect client and is able to connect fine, to begin with. However, once they reboot their computer and try to reconnect, the VPN session will not come up and they receive the error message below."The service provider in your current location is restricting access to the internet. You need to log on with the service provider before you can establish a VPN session. You can try this by visiting any website with your browser." 
 
Reading other posts, it seems this message appears when a captive portal is restricting internet access. It must be a false alert in this case as there is nothing of the sort here. Apparently, Anyconnect 3.1 can generate a false alert like so if the name of the firewall's SSL certificate doesn't match the CName listed on the Client Profile. I've set this up to match, to no avail. Although users can connect by reauthenticating through the SSL VPN login web page, I am stumped as to how to get rid of this captive portal error that pops up when they try to use the Anyconnect client.

View 4 Replies View Related

Cisco :: LMS 4.0 Fault Management Module Alert Doesn't Show Current-Utilization Percentage

Feb 22, 2012

I would like to know if there's a way to show Current-Utilization percentage within the messages generated by the Fault Management Module in LMS 4.0 [code] As you can see above CurrentUtilization percentage is not shown in Event Description section.

View 2 Replies View Related

Cisco Firewall :: Firewall Alert In Log Buffer 2800 Isr

Aug 3, 2012

I'm getting this in my log buffer off my Cisco 2800 ISR. Seems like a firewall alert and  I've looked it up but, having a hard time really understanding what this really means.Should I be worried about this? Aug  2 18:27:56.380: %FW-4-ALERT_ON: getting aggressive, count (3/500) current 1-min rate: 501,Aug  2 18:28:29.792: %FW-4-ALERT_OFF: calming down, count (0/400) current 1-min rate: 84.

View 1 Replies View Related

Cisco :: Test Fast Roaming Using A Cisco 2100 Series Controller And 2 1140 APs?

Jul 20, 2011

I'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.

View 1 Replies View Related

Cisco WAN :: Does Cisco Catalyst 2960-8TC Support Bandwidth Limit Control

Aug 22, 2011

We are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.

View 1 Replies View Related

Cisco Wireless :: WLAN Cisco / AP 3502e - How To Get PAT (Product Acceptance Test)

Dec 3, 2011

I want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.

View 0 Replies View Related

Cisco Firewall :: Cisco ASA5510 Unable To Block Unwanted URLs

Jul 12, 2012

I have  cisco ASA5510 firewall  using in my network but  unable to bolck Url's  unwanted. can i block the [URL] on the asa by using regular exp.

View 3 Replies View Related

Cisco Switching/Routing :: Configuring COS On 2960G Switches With Non-Cisco Phones

Mar 1, 2012

I have 7 POE switches that have ESI IP phones attached.  I have two VLANS, 1 and 2.  VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
 
I have had voice quality issue between floors in my building.  Talking to others on my floor via the IP phone, there are no voice quality issues. [code]

View 1 Replies View Related

Cisco Wireless :: Connect Ap-1242AG With Non-cisco Router To Work As Repeater?

Nov 18, 2012

is it possible to connect Cisco Ap-1242AG with non-cisco wireless router to work as repeater?

View 1 Replies View Related

Cisco :: Unable To Understand Cisco Syntax For Nat Rules On 5550

May 1, 2012

I am looking at a config on a 5550 FW, and am trying to make sense of the syntax of the following rules. I have been to the Cisco site, but can't find much on the syntax.

View 8 Replies View Related

Cisco :: IPSec Tunnel Between Cisco ASA And OpenBSD (Access Enforcer)?

Mar 10, 2011

I currently use a device called the Access Enforcer which runs OpenBSD. I have 3 stable, working VPN tunnel's where the other side's device is a Cisco ASA 5520 or 5540. I was setting up my 4th VPN where the other side used a Cisco ASA 5520 and ran into issue's. The Cisco side can bring up the tunnel. Once the tunnel is up each side can talk to the other side. However, when the tunnel is dropped, the OpenBSD side cannot bring up the tunnel. The error received is on the OpenBSD device is "isakmpd[29581]: transport_send_messages: giving up on exchange from-XX.X.X.0/24-to-XX.XXX.XXX.240, no response from peer XX.XX.XXX.141:4500". I have been trying to figure this out for weeks now and can't seem to find the cause.

View 3 Replies View Related

Cisco Switching/Routing :: Cisco 3750G Error During POST

Dec 5, 2011

I am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error -
 
% Error: Unable to create flash:/microcode_update% Error: It must not already exist

Normally, getting an error during POST isnt a good thing.  My first thought was that flash was corrupted or flagged RO somehow. I did fsck flash: with no change.  I next tried fsck /test flash:.   It tested 77 blocks and performed 0 erasures.  It had been running for about 15 minutes with no problems reported so far.  Multiple reboots of the switch still report the same error.
 
I have reviewed the history of what I have done on this switch and finally think I found the problem.  I noticed a microcode_update directory that I am not used to see on a 3750.  Deleted the directory using the rmdir command and rebooted the switch.  On reboot, I noticed that a front_end/ directory was listed as being created as well as fe_type_1 and fe_type_2 were created.  The switch now boots up without any errors.

View 3 Replies View Related

Cisco Wireless :: 2 Cisco Aironet 1401 APs Keep Kicking Users Off

Jan 3, 2013

I have two Cisco Aironets 1401 connected to a Cisco Catalyst 3560 Switch. When users log onto the Wifi the APs authenticate with a Freeradius that then authenticates with LDAP.
 
Recently users have been getting kicked off of the network but I'm not sure why.If so how do I set these APs to roam with my setupd?For all I know there could be an issue with the switch I'm just not sure where to start when it comes to troubleshooting this issue.

View 17 Replies View Related

Cisco :: CISCO Advanced Firewall On 2911 Router Using CCP?

Dec 29, 2012

Guys I am using a cisco 2911 router with three interfaces: Gi0/0 connected through a switch to all my servers and Gi0/2 which will connect to another server, and Gi0/1 is my outside interface connecting through a switch to two ISP's.I have webservers and Terminal servers/File Servers with 10.0.0.0 network address connected throught My Gi0/0 interface.Now I want to implement a Cisco Advanced firewall for security on my router using CCP.I want the firewall to work such that it allows external users to access the servers on Gi0/0 through ports 0,23,25,20,21,53, 110,3389. and to access the SIP server on Gi0/2. My issue is can i just create two DMZ's for both interface Gi0/0 and Gi0/2 without creating an inside zone and Gi0/1 as outside zone as my internal traffic is mostly server based and the users connect remotely through terminal server to access resourcess using RDP, secondly how do I open the relevant ports.I have checked alot and all I have seen is just basic process on using the wizard I have no idea how to go about this issue.

View 19 Replies View Related

Cisco :: How To Connect Laptop To Cisco 3550 Switch

Mar 30, 2011

I bought a new cisco 3550 switch to prepare for my Cisco certification prepration. Actually i dont know how to connect the cisco switch to a laptop with only usb ports....... earlier i used to do my practise using Cisco packet tracer but i think for CCNP switch that is not enough thats y i bought second hand switch. how can i connect that switch with my toshiba laptop which has only USB ports. do i need to buy some sort of convertor or other hardware. And if so what does u call it and how much does it cost?

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved