Connecting To Internet Using Bridge Mode And See Other People In Network?
Nov 4, 2012
I am a ADSL user and connect to internet using bridge mode that is set in my ADSL modem/router. when I open My Computer in Windows 7 I see a list of other people in my Network section as shown below. Other problem is that when I want to go to my modem web panel by entering 192.168.1.1 in my browser, I see it tries to connect to other modems and if I enter default user/pass I can log into other peoples modem! Is that my ISP fault for misconfiguration?
View 12 Replies
ADVERTISEMENT
Mar 23, 2011
I have a Thomson TG585 v7 router which is in bridge mode. I also have a NetGear DGND3300v2 router which I would like to connect to the Thomson (eventually I will purchase a switch and connect another device along with the NetGear). The problem is that the NetGear only has 4 LAN ports and no WAN ports, which I assume you would need to set this up.
View 4 Replies
View Related
Dec 20, 2012
Just bought a new router and repeater for a wifi hotspot i am currently running.. I thought i was havng problems with the repeater after i change from router to a server, (and i'm now using a router in bridge mode) so the server is managing all the dhcp.. etc, Hence, the router is Running as an access point. The server which is a Hotspot Server does the rest. For some reason, repeaters, do connect to the access point apparently, but when connecting the client to the repeater (instead of access point) I can't get internet access. although i do get access to the repeater setup.and access point setup too.. or if that is the fact that repeaters must be connected to a router, not access point? should I use it as a WDS? or AP-wds? I have a Cisco Lynksys e1200 router (which i'm using as access point) and an Encore ENXWI-1AN45 3 in one range extender?
View 2 Replies
View Related
Dec 11, 2011
How do you set up a linksys routers internet configuration type to public/bridge mode? my model is WRT45g
View 1 Replies
View Related
Jan 1, 2013
We have a RV120W Wireless-N VPN Firewall and we want to configure the router in brigde mode (transparent). Because we have another Firewall, use for filtering and default gateway on the LAN. The ISP provide IP address by DHCP, so we must connect the internet connexion to the WAN interface. But How can we do for connected the RV120W to our firewall? The router mode on the RV120w allows-it to make this configuration?
View 1 Replies
View Related
Aug 9, 2011
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies
View Related
Dec 22, 2012
I am creating a migration plan for our organization, Im wondering, how many domain controllers people have, how many member servers and what there used for?
View 3 Replies
View Related
Sep 7, 2012
how do i stop people from picking up my netgear and using there internet free off me
View 1 Replies
View Related
Mar 6, 2013
I just got new roommates and the internet on his computer would only load facebook and google. NOTHING else. It said he has internet connection but it still wouldn't work. I even called my internet provider and they couldn't figure it out. His internet worked perfectly fine when it was on safe mode with networking. I even disabled his firewalls and I ran malewarebytes but found nothing. I thought this was just his computer but then a day later my computer is doing the same thing! my computer has worked perfectly fine for over a year on the same router and everything but now it has the same exact symptoms as his. I don't know if this is a router issue or not. .
It is a wireless connection, internet provider is cable one, and my router/modem is a Zoom DOCSIS 3.0 cable modem/Router with wireless -N
View 2 Replies
View Related
Jan 10, 2013
1) How do you manage your inventory of network equipment from the time you receive a product into inventory to the time you decommission it?
2) How do you make aware the people who manage your network monitoring/reporting software that a device has been added/removed from the field?
2a) How do you notify the people who manage your network monitoring/reporting software of what is to be monitored on a new device in the field? Of a new interface that has been added/removed on an existing device?
2b) How quickly do you notify for 2/2a? i.e. minutes, hours, days, etc.
3) What types of interfaces and resources do you monitor on a network device?
View 3 Replies
View Related
Aug 19, 2012
Have a PC set up with a LINKSYS N2500 router. this is password protected for access to network I would like to monitor what one of my children is doing on the net - but they surf the net using an iPad
View 4 Replies
View Related
Feb 6, 2012
How to set the WNR2000v3 into Bridge Mode. I can not find instructions on it in the user manual or the NetGear website. And Google.com has turned up not valuable results either.
I have the WRN2000v3 plugged into another router via Ethernet. I basically want to "dumb down' the WNR2000v3 into a basic Ethernet switch.
View 5 Replies
View Related
Jan 2, 2011
how use wrt54g v3 bridge mode
View 2 Replies
View Related
Feb 6, 2012
I have 2 Cisco 877 routers and I need one set to bridge mode and one is gateway internet? How do I do?
(LAN)
ADSL <---------------->877 <----------------> 877 Gateway <-----------> Clients
View 3 Replies
View Related
Apr 22, 2012
I have a Westell 6100 modem. After my old router, a DIR-655, got zapped by some electric charge from a nearby thunderstorm, I bought a Netgear WNDR3800 router. But I have not been able to get the Netgear router to connect to the Westell 6100 modem reliably [URL]
A friend had given me a Netopia 3347NWG router/modem some time ago but I had never attempted to use it. I was able to get into the web setup screens of the 3347NWG and, without attempting to connect the Netgear router to it, I was able to connect to the Internet via the setup screen. But every attempt to actually go to a web address would fail with a timeout, and efforts to ping always failed with a timeout. Yet the 3347NWG setup said I was connected.
Does anybody know how to setup the 3347NWG so it actually can connect to the Internet correctly so that I am able to surf to a web page or ping an address successfully ?
Does anybody know how to setup the 3347NWG in Bridge mode so that I can use it strictly as a ADSL modem and try to use it with my Netgear WNDR3800 router ?
If I can not use the 3347NWG with my Netgear router I had planned to send the Netgear router back for a replacement since it is not connecting relaibly to my Westell 6100 modem. But if I can get the 3347NWG to work as a modem and reliably connect my Netgear router to it, I will not have to send back the Netgear router for another one.
View 1 Replies
View Related
Aug 25, 2012
In the LAN side configured one Interface VLAN and Configure IP address on that and add the AP’s to the VLAN .. and on the WAN ADSL its p2p with Qtel bridge mode ..
from the Access Point I am able to reach 172.31.30.30 which is the router far interface . BUT still not able to reach the ISP side 172.31.30.29 .
Router Config
no ip routing
bridge irb
bridge 1 protocol ieee
bridge 1 route ip(code)
View 4 Replies
View Related
Dec 14, 2010
I have a TWC wideband modem and service. I know that they will enable bridge mode if I ask them. My questions are. After they enable it whats my setup? Do I just run a cable from their modem into a new router that I then set up on my own? Is it that simple?
View 2 Replies
View Related
Jun 20, 2011
I have to use a single network connection to provide LAN / WAN to a computer and an Apple TV.Is it better to use a network bridge or internet connection sharing?One connection is Gigabit and the other is Ethernet. If I use a bridge will it be degraded to 100Mbs?
View 9 Replies
View Related
Mar 26, 2011
I'm trying to connect my Ipod to the internet for updates that i cant download directly with my laptop. I'm Using a Laptop (Vista) with a Built-in Wireless, and i only have internet access with a Telstra mobile internet USB.
I have created an Ad-Hoc network, but still can't get my ipod to connect to it. and i can't bridge my USB Internet connection (shows up under dialup) with my ad-hoc network (shows up under LAN/High Speed Internet). I have also changed the settings for ICS.
View 3 Replies
View Related
Dec 5, 2012
Can ASA 5510 be configured as bridge mode and still send Netflow info to a collector?We have a PIX connect internal network to internet. Because PIX does not support NetFlow, as a temporary solution, we were thinking of putting an ASA 5510 between the PIX and internet gateway, and configure it as a bridge so that there will be no routing issues, and the ASA can still send Netflow info to a collector.
View 13 Replies
View Related
Mar 5, 2011
i want the Satellite receiver to be wireless.i have a I-Link 9000 Plus Satellite reciever which has an ethernet port , where the buffalo router will be connected. (Buffalo WHR-HP-G300N Firmware: DD-WRT v24SP2-EU-US My main router is the Linksys Wireless G router WRT54G2 V1.5.
View 2 Replies
View Related
Aug 29, 2011
I have an SMCD3GN (from Rogers) that is both a Modem and a Router. I also have a Linksys WRT54G router that I used to use before. The SMC is giving me a lot of problems. The connection is really bad often and my internet speed drops for no reason all of a sudden. I'm getting fed up and want my old router back.
I know it's possible to change the SMC into a modem (put it in bridge mode) and then connect my router and use the Linksys router instead of the SMC. The problem is, I don't know exactly how to set it up and would really like an explanation. I already know how to get into the SMC and Linksys settings as an admin.
View 1 Replies
View Related
Dec 25, 2012
Region : Italy
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.20 Build 120705 Rel.39030n Beta
ISP :
I'm facing problem to properly set BRIDGE mode (WDS Bridging). I had a router connected to ADSL line with following setting:
IP 192.168.1.1
Security setting - WPA2/TKIP
DHCP on
The wi-fi coverage is not good in all the floor so I'm trying to extend coverage using a TL-MR3220. I did follow the instruction in this video [url]....
View 3 Replies
View Related
Apr 13, 2011
I m setup for my brother's next house. He wants to use to share with my internet access. I do have 2wire modem provider that has wireless capability in my house. So he have DAP-1522 [bridge mode] and adjust in Wireless Setting, to use SSID manual, (Bell9**) WPA. It s successful, and works well. Problem is cannot use wired to computers, blu-ray, Xbox 360 in same time. it will disconnect frequently because in bridge mode doesn't have DHCP reserved?
My bro bought other one is DIR-655. DAP-1522 keep in [bridge mode] to link to DIR-655 (Static IP), and setup DHCP Reserved. He feel relief that works very well and have no problem with any computers and devices doesn't disconnect anymore. my question is why DAP-1522 doesn't have DHCP reserved when bridge mode that connected to any providers modem?
View 1 Replies
View Related
Apr 24, 2013
I have a WAG120N. I wish to use it as a modem only and not as a wireless router.I have another wireless router I want to use to handle network connectivity.I want the wag to be set to 10.10.1.1 and I want my router on 10.10.1.2What bridge mode do I set on my wag? Do I need a crossover cable?
View 1 Replies
View Related
Nov 30, 2011
I'v just changed my internet provider. That new one uses Annex b, my wag160n is purposed to annex a. Thats what i'v done. Turn on bridge mode turn off dhcp, set PPPoE with my login and password. And here is my problem. I cant connect by wifi with more then 1 device. I can only connect with my laptop when i'm trying to connect on my xbox it says it cannot get ip adress from router. What shoudl i change ?
View 6 Replies
View Related
Nov 23, 2010
I am running a DAP-1522 (v1.21) in Bridge mode with a DIR-615 (1.00VG). I have configured the DAP-1522 to access the WiFi network and can see it connects correctly. I have a PC connected to the DAP-1522. Most of the time I can ping the DAP-1522 from the PC but cannot ping the DIR-615. Occasionally when I reboot everything again I can ping the DIR-615 and get full internet access but this usually only lasts a minute or so then it drops. After that I can only ping the DAP-1522. The DAP-1522 always says the Status is "connected" though.
The IP addresses are as follows:
DIR-615: 192.168.0.1
DAP-1522: 192.168.0.50 (static)
PC: 192.168.0.55 (static)
View 9 Replies
View Related
Aug 22, 2010
I've got a DIR-655 set in bridge mode after a Cisco router. It's been working great for months, but now I'd like to add a new wireless device and want to get the settings. For the life of me, I can't remember how to access it now.The subnet is 192.168.2.XXX I've got a Mac connected through the "internet" port and a cat5 cable. I figure I should be able to go from 192.168.2.1 through 192.168.2.254 and will eventually find it. Is there something I'm missing?
View 7 Replies
View Related
Jan 15, 2013
I currently have frontier dsl internet and am using the isp provided modem/router combo and a DIR-655. I have the modem running in bridge mode and the 655 set to PPPoe connection, MTU at 1492. I confirmed the MTU setting on the isp modem/router before bridging it. The question i have is if the router MTU is set to 1492 does everything on the LAN side of the router run at 1492 or does it run at 1500 while the router breaks the packets up? Everything works fine but my pc's all use vista and i'm not sure where to check the mtu settings at and all my game consoles are set to mtu automatic so i can't really see what they're running at either.
View 7 Replies
View Related
Mar 20, 2011
Is it possible to put the SRP 527 into Bridge mode to use it just as a modem?
View 6 Replies
View Related
Nov 22, 2011
I turned it on for bridging and it did not auto setup wireless so i need to turn off WPS but my wireless option page is now blank. I rebooted, reset the DAP but still no manual config option. I found I could configure it if I switched it to AP mode but still cannot setup from bridge mode. According to manual a reset does not turn off WPS so what is the answer?
View 1 Replies
View Related
Dec 4, 2012
Can ASA 5510 be configured as bridge mode and still send Netflow info to a collector? We have a PIX connect internal network to internet. Because PIX does not support NetFlow, as a temporary solution, we were thinking of putting an ASA 5510 between the PIX and internet gateway, and configure it as a bridge so that there will be no routing issues, and the ASA can still send Netflow info to a collector.
View 1 Replies
View Related
Aug 23, 2011
My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies
View Related
