Home Network - RDP From Work To Home?

Jun 10, 2011

I am trying to RDP from my office to a PC at home and it is not working.It stays at the "configuring remote desktop". I'll start by mentioning the network devices installed and then I'll mention the steps I took from the PC all the way to the furthest point on the network.

I have a Verizon FIOS wireless router connected to a Linksys wireless router.The WAN port on the Linksys is connected to one of the 4 ports on the verizon router.The WAN side is on the 192.168.5.0 network and the LAN side is on the 192.168.1.0 network.So here's what I did on the PC:

- I enabled RDP by right clicking "Computer" and enabling remote access.

- I also changed the default RDP port in the registry to 49152

On the Linksys router:

- I am forwarding port 49152 to the IP address of my PC (192.168.1.xx) for both TCP and UDP

On the Verizon router:

- I have the firewall settings set to minimal (i did this so that the Linksys can act as the firewall)

- Even though I set it to minimal, I still configured it to forward port 49152 to the WAN port of the Linksys router (192.168.5.3) for

both TCP and UDP

What am I doing wrong? Could it be something on the network at my job blocking it or something with my configurations?

View 10 Replies


ADVERTISEMENT

Home Network :: Why Won't Static IP Configuration Work

Jul 2, 2011

I'm connected through a simple non-configurable switch to a 172.20.0.0. 255.255.0.0 network, with a gateway of 172.20.2.2.

When i use DHCP, i am able to connect to the web.

When i change my ip address to a static address (with an available ip address and correct subnet mask and default gateway) i am unable to connect to the web.

View 7 Replies View Related

Work Proxy Bypass On Home Network?

Aug 23, 2012

When I'm at work, I have internet (though a proxy) and remote access to the linux computers at work (the work laptop runs win 7)when I have to work at home, the work VPN that we were given has no internet access but I can connect to the remote linux computer that I need just fine. the linux computer has no internet access and more often than not is missing modules and dependencies. Is there a way to enable my home wifi network and the VPN so that the work computer can access the internet locally while I'm working? just one browser is all I need.... I currently have to disable the vpn, download my modules and then connect, to install them.

View 5 Replies View Related

Connecting Lenovo Home Laptop To Work Network

Feb 23, 2011

What do I need to connect to my office network when want to work at home from my laptop.

View 1 Replies View Related

Home Network :: How To Make Wireless Router Work

Apr 7, 2013

how to make a wireless router work on a lan network, where my ISP has set the TTL to 1 so i can`t use a router.

View 3 Replies View Related

Home Network :: Windows 7 HomeGroup Doesn't Seem To Work?

Jun 27, 2011

Im looking to create a home network with a wireless router.I have three machines, one computer is downstairs connected to the router with an ethernet cable, my other two machines are upstairs and connet to the internet wirelessly through the same router downstairs.I want to be able to connect to my upstairs computer with my laptop and access my files, i have an external hard drive connect to my computer and want to be able to back up to it from my laptop without removing cables.All three machines are running windows 7, the homegroup doesn't seem to work?

View 5 Replies View Related

Home Network :: Advanced Home Network Setup (3 Subnets) And Port Forwarding?

Feb 24, 2013

I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:

- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface

Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.

- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.

- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.

Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.

Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)

Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).

View 5 Replies View Related

Home Network :: Playing MPEG-2 File In Webpage From Home Server?

Dec 20, 2012

I have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?

View 4 Replies View Related

Home Network :: Use Internet Of Workplace From Home Via Dial-up Connection?

Oct 3, 2011

I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)

View 11 Replies View Related

Home Network :: Latest Ethernet Cable For Home Wiring?

Sep 20, 2011

I'm currently in the process of buying the new property, which is in the build process and would like to put some cables across 3 floors, which would be connected to the router downstairs.

View 3 Replies View Related

Home Network :: Windows 7 Laptop To XP Home Desktop Wireless

Mar 13, 2011

I have been having a bit of trouble with networking my two machines to share files and allow printing i have a win 7 laptop and a xp home desktop. I share a net connection via 02 wireless box both systems have wireless i have tried many things

View 8 Replies View Related

Home Network :: Notified When Somebody Tries To Connect On Home Wifi?

Nov 24, 2011

My Wifi network has a wpa2 password that is a random string of characters and numbers and yet last month a rogue IP Address kept popping up on my DNS list. It has to be coming from my neighbor who's bedroom is about 15 feet away from my router. So unless someone is sitting out on my front lawn to do this then it must be him.I've been looking for software that will notify me when a connection my router is attempted and kudos if it also asks my permission first would be great.There are wifi packet sniffers out there like Cain&Abel, Airsnort, that sort of thing but I am not quite savvy enough nor do I want to turn this into a complicated hobby but just need a basic warningin case something gets past my passwords again

View 3 Replies View Related

Home Network :: Convert UTStarcom WA3002G4 Into A Hub For A Home LAN?

Jul 9, 2012

Following are my components at hand.

1. My super awesome desktop with the regular gigabit, on board lan card (on Win7).

2. A laptop, with wireless connectivity (again on Win7).

3. A modem, UTStarcom WA3002G4 with an internet connection from BSNL.The modem is a wireless modem.

I want to be able to connect the laptop and the desktop in a single LAN connection, so that

i)I may play NFS Most Wanted on both the laptop and desktop through the LAN play.

ii) I may share files and folders, fast and without any hassles.

View 3 Replies View Related

Home Network :: Need To Extend Reach Of Wifi Network At Home

Oct 20, 2011

Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.

View 1 Replies View Related

Home Network :: Install A Wireless Network In Home Environment?

Nov 10, 2011

How to install a wireless network in home environment?

View 6 Replies View Related

Home Network :: Need Input On Network At Home Newly Wired

Jan 14, 2012

I am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.

View 1 Replies View Related

Home Network :: Can't Get D-Link DGL-4500 To Accept Home Network?

Sep 10, 2011

I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."

View 3 Replies View Related

Home Network :: Unable To Get Home Networking

Oct 16, 2011

After trying most things and spending money like water, I still cannot get our home network to be adequate and I am out of options - Tried using two 100MBit/s Netgear routers "bouncing" signal to each other (Wireless Repeating Function). Not ideal as security is small and speed was slow (<10MBit/s) but at least it worked. However these routers had to get pensioned off when we put gigabit ethernet in the office - and the Netgear replacements (a) still have the security limitations with wireless repeating, (b) anyway see to do a worse job of repeating. Tried buying Netgear directional high-gain antennas and directing the signal point to point to a second router - didn't work at all. Tried Powerline (this was in 2008). It sort-of worked but was unreliable and dog slow. I think this is probably not worked by the fact that this building is OLD, most of the wiring is OLD, and anyway the electrical path would take the signal from the 4th floor, down some very old wiring to the ground floor, across a very old switchboard, and back up to the second floor... it's not quite the same as a modern house with modern wiring. Most recently tried using Netgear's Wireless Network Extender. Again, it sort of works, but it's NOT fast at all. In addition there are times when some of our computers using the extension segment of the network are unable to connect - they can still see 3-4 bars of signal, but they cannot get on the network. Appears to be an issue relating to gateway, or DNS, not sure. But I would say about 1 day in 3, when I come home, my wife tells me that the "internet is off".

View 4 Replies View Related

Home Network :: Adding A TV To Home Office?

Jan 9, 2011

My home network consists of a Linksys WRT54GL router running DD-WRT supplying wired access to my desktop, a bridge to another WRT54GL (also running DD-WRT) to provide a wired connection to a XBOX upstairs, and wireless access to about 5 or 6 different devices including several laptops, an iPad, and an iPod touch. My question is this:

I am adding a 22" TV into my office so I can watch TV while working on my desktop. I only have one cable jack in my office which is currently plugged straight into my cable modem. This means I'll have to use a splitter to give both my TV and modem cable access. How much signal degradation or speed do I stand to lose or should expect to lose?

View 13 Replies View Related

Home Network :: Home Ip Is Public But Can't Be Pinged

Oct 26, 2012

I have a public ip (I didn't ask for it, but I have it). Ping worked, including ssh, etc. No it doesn't work anymore.

View 3 Replies View Related

Home Network :: AP For Extending Wireless At Home?

Jul 24, 2011

I am wanting to buy an access point to extend my range on my home network. I think i've used one AP before and if i remember correctly, after i plugged it into my main rounter and configured it, i unplugged the ethernet from it and moved it to somewhere else in the house. But i can't remember for sure if this is how it works or do i have to have an ethernet cable running to it at all times?

View 10 Replies View Related

Home Network :: Organising Home Lan?

Oct 8, 2012

Here's the structure that i want to make from my lan network (1 server and few user computers, conected in lan)

-All files need to be stored on server

-Automatic backup from one hd to another (both on server)

-All user from other pcs can modify files on server, but they cant move,copy,delete or save them on their pc or other removable devices

-Every user has to use his own account to access server and files

-If files are modified by programs on other computers, they must be saved only on server, not on local hd.

So, now I need someone to tell me what's best software resolution for this. Maybe windows active directory(with 2003 server), or some other solution is better? In general i need to know what to use, and then i will google out tutorials for setup.

View 2 Replies View Related

Home Network :: How To Use Two Routers At Home

May 17, 2011

I wanted to know how to connect two routers together and make them both where I could connect to the internet with them. First off, here is my setup. I have a main router, named "Main" and another router named "dd-wrt". I have the dd-wrt firmware on that one. From the Main router, I have a 50 ft cord running through my house, to my room, which consists of a switch and a desktop. I read that you had to put the second router in client mode in order to do this. What do I need to do in order to have it setup where I have two visible wireless connections on my laptops, and I can connect to either one of them through wireless or Ethernet and get internet access?

View 8 Replies View Related

Home Network :: IPhone Kills Home Network

Oct 17, 2011

Every time I connect to my home network with iPhone 4 my whole network stops working. Windows 7 is not reporting any problems with connection, nor is my router. I have cable connection with my PC and wireless with my laptop, they both just stop working without any visible reason. Even the iphone i connect with wont work, but of course it says its connected and everything is ok.I tought it was an iOS 5 problem, so I reinstalled it. It worked for an hour then its all back again. I even tried sharing my PC conection so that my iPhone is connected to PC and not directly to router.But that produced the same results.

View 6 Replies View Related

Home Network :: Unique Situation With Home Network

Mar 9, 2013

My Set up at home is as follows: [code] Now according to what I have read I should be able to set the subnet on .2.0 network to a subnet of 254 and this gives me 512 Hosts I believe however my question at this point is how to route between 192.168.1.0 and 192.168.2.0.Or when I set the subnet .254 does the router just route it automatically.I would still set the subnet mask on both networks to 254 correct? I believe I can only use 192.168.0.1 to 192.168.1.255 w/.254 subnet mask. However I already have some servers that are configured with applications (On the 192.168.2.0 network) that I do not want to change ips on because it would be a pain to reconfigure so, my other question is other than using .252 to extend it to 192.168.0.1 to 192.168.3.255, (I need the 192.168.2.0) is there anything I can do? Like use 192.168.1.0 with subnet mask of 255.255.254.0 to get the 192.168.2.0 network? The reason I asked is I was using a subnet calculator to try and figure this out but every time I put in 192.168.1.0 with .254 subnet mask it changed the ip to 192.168.0.1 to 192. 168. 1. 255.I would really like to use the netgear only. The way I have it now is not working I am able to ping the internet from the 192.168.1.0 network but I can't ping from 192.168.2.0 network to the 192.168.1.0 network.

View 2 Replies View Related

Home Network :: Setting Up A Small Home Network Of 10 PC's?

Jul 27, 2012

want to setup a small home network of about 10 PC's.I want them to share the internet connection of 25mbps.I also want Printer Sharing.

View 2 Replies View Related

Home Network :: Integrating 3550 Into Home Network?

Jul 13, 2012

At the moment I have my home network (192.168.0.0/24) like as below (all connect using straight cables): [code] My Cisco lab equipment are in the basement all connecting to an access server which at the moment is plugged into Switch3-dumb (along with a printer & NAS).What I'm thinking is to replace the Switch3-dumb with a 3550 I'll be picking up later this week.Then using this to do as the Switch3-dumb did maybe by creating a native 'vlan 192' & putting it into a gig interface which will connect to the network using the straight cable, also putting the printer & NAS into the same vlan.This will hopefully still give me connectivity throughout.Then when required I'll like to use the 3550 with the rest of my Cisco equipment for setting up different labs (segmenting them from the home network by using different vlans etc.One of my reasons to implement the 3550 into the home network is to be able to play about on a regular basis (port monitor, traffic stats, etc).

View 2 Replies View Related

How To Use Work Internet From Home

Jan 10, 2013

how do i connect my pc from home to use with the works internet via usb internet stick

View 3 Replies View Related

How To Make Old Pc Work With Home Wifi

Oct 22, 2011

I have an older PC with windows 98 running. I used to have it connected to a modem and a router to get internet access.I recently got a new modem as the old one died and have now Wi-Fi in my home. My newer PC takes advantage of the Wi-Fi but my old PC does not.The new modem does not have a connection for the blue cable (Marked USB in back of modem) that was connecting the old PC to the internet.After reading online I think I need a USB wireless adapter but I am not sure on what I need exactly as my online searches return too much stuff (I went on Ebay).

View 3 Replies View Related

Using Home Printer With Work Laptop?

Mar 18, 2012

I have a work provided laptop connected to my home router, and I logon to the work domain using a VPN client. I want to be able to print to a printer that is connected via USB to another computer on my home network. That computer is not allowed to logon to the work domain. Is there a way to do this without making changes to the work computer?

View 5 Replies View Related

Cannot Get VPN To Work Correctly At Home With New Laptop

Jan 21, 2011

Ok so our company has a VPN set up on our workstation laptops for employees to be able to connect to the office network from home.We use CISCO VPN CLIENT, and a pre-setting .pcf file to upload our vpn into the client. The settings are correct completely to allow the VPN to work from home. All of our older workstations (Latitude D510-D630's) work with Windows XP SP3 32b. Recently i purchased new laptops (Latitude E6410's) and have started issuing them out with Windows 7 Enterprise 64b.A couple employees from home cannot get their VPN to work correctly at home with the New Laptops. Their old laptops work fine with the VPN, but the new ones dont. They are running a Frontier DSL modem with wireless.The VPN connects just fine on the new laptops, but the problem is... Nothing works. Outlook does not connect, They cannot access any of our network shares or drives. And cannot use any of our company's software that requires our network access.

I tried uninstalling the the CISCO Client, and reinstalling it, No Go.I tried changing the MTU Settings on the client and network adapters and wireless adapters, No Go.And it seems to be just an ISSUE with employees trying to VPN through a dsl connection using the new laptops, where others with the new laptops can VPN in fine through a time warner connection. But remind you, their old laptops work fine.. which seems kind of odd to me.

View 7 Replies View Related

Home Network :: Trying To Add Password For Home Network

Jan 29, 2013

I opened the setting 192.168.1.1 then enabled the WPS, selected the WPA-PSK mode and entered the preshared key I deleted all the saved devices and made a restart for the router.trying to add a password for home network.

View 2 Replies View Related

Connecting Work Computer To Home Internet?

Mar 30, 2013

I recently was given an old computer from work. I tried to connect it to the internet at home but it wouldn't connect. The icon at the bottom shows that it is connected but the web browser shows that i'm not connected. All the computers at work are connected to a network so there may be some settings that won't allow it to connect at home. I did go on to internet options under connections and changed the default connection from the work network to broadband but still no luck. None of the proxy boxes were checked either. The OS on this computer is Windows XP. Also, all connections to my home internet are fine.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved