Linksys Wireless Router :: Fail To Open Ports E4200v1
Jan 4, 2013
im moving over to VDSL.But now i cant open any ports on the E4200 no mather what i do.It worked with the previous modem, but now i cant open anything. all the ports seems to be closes, 80, 21 etc, and the ports i manually forrward.The previous modem was a ZyXEL P-2602HWT-F3, and the new one is a ZyXEL P-2812HNU-F3.If i connect directly into the ZyXEL P-2812HNU-F3, every ports seems to be open, port 80 is open, port 21 is open, but not on the E4200, and yes, i have tried open the FTP ports.I have tried the 30/30/30 reset on the E4200.
View 6 Replies
ADVERTISEMENT
May 23, 2012
I have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies
View Related
Apr 30, 2013
I tried forwarding ports 80, 443, 7001, 8888, 9901, and 9911 on my Linksys E1000 router but whenever I check my ports always come back as closed. This happens even why I try to enable DMZ.
View 9 Replies
View Related
Jan 20, 2012
How do I open ports 443 and 80 on my wrt160n v3 router?
View 1 Replies
View Related
Nov 18, 2012
My LinkSys E2500 wont open my ports, I have tried DMZ mode but it still does not open any of the ports.
View 9 Replies
View Related
Jan 30, 2013
I am trying to open ports 53, 80, 88, 1863 and 3074 for my xbox. I then run PFPortChecker by Portforward and it tells me the ports are not open.
View 9 Replies
View Related
Nov 13, 2012
The last few weeks I've been having problems with my 360 Slim. Sometimes it boots up just fine, other times it wont connect to XBL at all. Some days I have a open NAT, other days I have a moderate NAT.
I have followed the steps on the portforward website. I make a static IP and all that good stuff. I open the ports, using the IP address the Portforward static IP program gives me. After that...My computer stops working. It fails to connect me to any websites at all.I'm running a Linksys ea3500 router.
View 3 Replies
View Related
Aug 23, 2012
I am using remote management to attempt to open port 8889 on my Linksys WRT54G router. I have successfully opened ports 22 and 80 with no problem. Additionally, I can close and reopen these ports without having to physically reset the router. However, if I try to open any other port (I have tried various ports: 23, 100, 8888, 8889, and several others) this port will not open. The ISP this router is connected to is Comcast and according to this site URL port 8889 isn't among the ports that Comcast blocks. I have tried everything I can think of to resolve this issue (short of manually resetting the router or restoring the default settings).
View 9 Replies
View Related
Mar 24, 2013
I am running a Linksys Wireless G 2.4 GHz Broadband Router Model WRT54G. I am unable to open any ports. I upgraded to the latest firmware yesterday but still am unable to open any ports. I even turned off my Symantec Internet Security Suite Firewall but still am unable to open any ports.
View 2 Replies
View Related
Mar 5, 2012
How do I go about opening specific ports on an E4200?I'm having disconnect issues with a particular game, and the Customer Service drone thinks the ports required for the game aren't open. Nevermind the fact that it's worked fine for 6 months now, and the problem only started a few days ago.I figured I'd humor the idiot and open the ports, but all I can find is information on forwarding, not making sure the ports are open
View 3 Replies
View Related
Dec 29, 2011
I need to open four ports and have no idea how. My web host thought that my ISP was blocking them; the ISP says they are not and that it is teh router. I don't have pjone support anymore (WRT54G is old) so could not be walked through it by a tech support person.
View 1 Replies
View Related
Dec 9, 2012
I have been using Linksys routers for quite some time now, and recently made a big upgrade from the WRT54G to the E3000. I am familiar with the 192.168.1.1 interface and its functionality. However, I recently noticed a problem: when I set a port to forward traffic to any IP address on my network and then check whether or not it is actually open (url...), I am told that the port is still closed. More interestingly still, the first port that I forwarded when I first got the router is listed as open, but the other half dozen or so are still considered closed. I have been trying to set up a file transfer protocol (FTP) server, but can't even get traffic to forward from port 21! I even tried using the pre-configured FTP drop down on the Applications & Gaming tab, but to no avail. Has anyone had similar issues, or perhaps an idea as to why only one port is forwarded when I have followed the same steps that I have been using for years?
I tried to get in touch with Technical Support about this issue, but was told that I needed to purchase a $30 subscription in order to qualify for assistance. I don't think that I should have to pay $30 to know why the same steps work with some ports but not with others.
View 9 Replies
View Related
Oct 17, 2011
I've DMZ'd my computer using the the E1200's Web Browser Config screen (192.168.1.1) yet when I try to test the ports not a single one is open.
I've used this test to see if they were open: [URL]
And almost none of them were. Is there any issue that could be causing this?
Also when I try to open a single port the site says it times out. Opening single ports didn't work either. I've also tried to DMZ via the IP and the MAC address of my PC and still no luck.
View 9 Replies
View Related
May 27, 2012
I have been trying to host games for some time now with no luck. I believe it is because i cannot open the proper ports. I own a Linksys BFSR41 Ver. 4 router. I have been trying to open ports, testing them on a port checker website and they are always listed as closed. I have followed the guide on portforward.com perfectly with no luck.I have disabled Block Anonymous Internet Requests.I have disabled my Windows firewall, and AVS. Still cannot open ports.I have also updated to the latest firmware. I am using Win-7 x64.
View 1 Replies
View Related
Nov 16, 2011
i cant open my ports because i have a internet connection that first goes to my router and then to my modem.
View 3 Replies
View Related
Jan 31, 2013
The Cisco E4200 is supposed to support something called DFS (Dynamic Frequency Selection). These are wifi channels that, due to radar operating on the same frequencies in certain areas of the US, the FCC requires devices using them to do what's called "radar avoidance" -- they're supposed to scan the channel periodically and, if a radar signal is detected on said channel, they have to vacate the channel for a specified period of time (typically around 30 minutes). Because of this, a DFS channel cannot be selected manually by the user -- it has to be selected automatically and vacated automatically in case radar is detected. So, I have my E4200 channel set to "Auto(DFS)"
The list of WLAN channels is here: [URL]
More background: each allowed 5 GHz channel is 20 MHz wide in the US. However 802.11n does what's called "channel bonding" -- it actually uses two channels side-by-side for increased throughput. E4200 owners will notice a channel width setting and one of the options is 40 MHz or Auto (20 MHz or 40 MHz) -- this is what uses two channels combined. I happen to have this option set to "Auto (20 MHz or 40 MHz)".
I discovered, through experimentation, that the router will ALWAYS select channel 149/153 as the operating channel if there are no other wireless APs in the area (channel 149 as primary and channel 153 as secondary). I always wanted to see the AP select a DFS channel, so I brought home a bunch of access points and started occupying spectrum. I put AP #1 on channel 149/153 and rebooted my E4200, at which point it picked channel 157/161. So I put AP #2 on channel 157/161 and rebooted the E4200, and it skipped channel 165 (note that there's not enough spectrum up there for 40 MHz, which is probably why it got skipped) and selected channel 36/40. I put AP #3 on channel 36/40 and rebooted the E4200 and to no surprise it picked channel 44/48. So I put AP #4 on channel 44/48 and it picked...channel 149/153?!?!
Just to be certain that there isn't a certain threshold required to force the AP to select a DFS channel, I moved all 4 APs RIGHT NEXT TO the E4200 such that their signal strengths exceeded -40 dBm, and then rebooted the E4200. It STILL picked channel 149/153!
Just what are the criteria required for the E4200 to select a DFS channel?!? DFS is advertised in the user menu, but I can't find any way to get the AP to select one of those channels. Does the AP *really* support them, or does it just say it does? If the E4200 does NOT really support DFS, then Cisco/Linksys should remove the term "DFS" from the user menu -- it is deceptive!!
Oh, I should mention that I'm in Santa Clara County -- Saratoga, CA. I checked the FCC database on radars and as far as I can tell, there are NO radars on DFS frequencies around here.
View 5 Replies
View Related
Jul 12, 2012
I have an e4200 V1 with firmeare V 1.0.04 For my IPv4 configuration I use opendns.com for my DNS provider.When I enable IPv6, I get my ISPs DNS server rather than the one I have configured on the IPv4 page. It works, but it eliminates all filtering and statistics that I am able to do with opendns.com.Open DNS does provide two IPv6 DNS servers, but I don't seem to be able to find where to set them in my e4200. I want it set network wide.Can I set my IPv6 DNS provider anywhere in the e4200v1 with V 1.0.04?
View 3 Replies
View Related
Apr 21, 2012
I got this replacement router and it is not even a week old and it is doing same thing the previous one was.
View 1 Replies
View Related
Aug 22, 2012
I have a Wireless Router supplied by my ISP that give me both 1G Lan and N Band Wireless, so I just need to use my 4200V1 as a Storage Access Point. I have done all the Bridge Mode configurations, IP Address ad Subnet / Default Gateway, etc to the routher and can see it on my Local LAN, by it's Set name.
I can not http or Https to the Config menu in any way, so I can not establish if a Disk is connected or not. The Disk device is USB Connected to the E4200 port, but I can not acceeass any of the files that are on it.
DGW - 192.168.1.1
E4200 - 192.168.1.200
Bridge Mode
Wireless Disabled on both Bands
DHCP Disabled
Everything appears fine, but not able to bring up Advance Configuration interface .
View 2 Replies
View Related
Oct 14, 2012
Found out if you make a ftp user called root you get access to your flash drive in via ftp it is normal or a bug ?
View 1 Replies
View Related
Jan 28, 2013
I've been trying to re-purpose my E4200v1 as a Bridge, AP or some other thing that might work with wifi coverage in my home. I am using an Asus as the primary router. and I have Verizon Fios so I have a coax/ethernet router with its wireless switched off so that the Asus is primary. That works, but when I go to reset the E4200v1, I can get it to take a new IP address, but when I attempt to put it into bridge mode, as soon as I hit "save settings" I see the admin screen flash and it goes back to its origninal settings, instead of saving the new settings.
View 9 Replies
View Related
Jan 16, 2012
I have the E4200v1 and if I remember correctly I think its on 1.0.0.3 (cant remember because I went back to my wndr3700). I had not had any problems with it until yesterday when I returned to playing The Hunter (first time playing it on the E4200) and my girl hollered upstairs saying that she lost connection on the laptop. I reset the router and she reconnected and I went back to playing the game. 2 minutes later she hollers again. I stopped playing the game to try to figure out the wireless issue and everything looked normal. No more loss connections for the next few hours..........Until I started playing the game again...so I took it out of line and put the 3700 back in line and played the game for hours with no connection drop to the wireless. Is this a knows issue on the 4200? Are some setting changes necessary to game on it? btw I was playing the game wired and it didnt effect the connection at all?
View 6 Replies
View Related
Feb 4, 2013
I've tried a number of ways to re-configure my E4200v1 router with Cisco Connect but without luck. I don't have the CD so I've downloaded it from this website and it loads and installs and launches but ultimately can never find the router. Part of the problem may be because I have a Verizon Fios Router already at 192.168.1.1. with the wifi and DHCP turned off, in favor of an Asus router which works well. I have tried taking the Cisco Connect installation off the wifi and onto a wifi through the E4200 Wan or Lan ports, but it still can't be found. I am able to get into the E4200v1 setting manually this way and to change its ip address to avoid the Fios Router conflict. But nothing works. Maybe I need to put the e4200 in the 192.168.1.1 range instead of the Asus 192.168.5.1 range? [code]
View 6 Replies
View Related
Sep 20, 2012
The E4200v1 does not play nice with the 4s on iOS6!!It will not work at all with Wireless N mode or mixed mode settings. If I have it on these settings, the iPhone will connect (slowly) to the router, but access content on the browser takes forever (or not at all).I have to set the router to G only nmode, but obviously this is no good for the rest of my devices!
View 3 Replies
View Related
Jun 19, 2012
I've had an E4200v1 in use as my home's main router for about 3 mos. And while many others have reported disconnect problems (I think), I myself have never seen any. My router and its N & G wifi networks have been rock solid. Until yesterday that is.Now all of a sudden, most of my family is complaining about wifi disconnects, slow speeds, etc. (My primary PC is hard-wired so I don't see any problems whatsoever... the problem apears to be wifi-only)And the Apple devices (OSX & IOS) seem to have the most severe problems. But Windows devices have also seen problems, just not as critical.Also, it's worth noting that I've been running 1.0.04 the whole time, without any problems... it seemed relatively stable to me. That is until yesterday.
I've bounced the router, I've disabled/re-enabled Wireless G network. I've switched mode from "mixed" to "G-only" back to "mixed". I've changed the channel width back to the default of Auto (I had been using 20Mhz), which increased my throughput (as measured by Qcheck) so I'm leaving it "Auto".
View 9 Replies
View Related
Apr 12, 2012
So I bought this new E4200v1 about a week ago and since yesterday it started dropping connection terribly. After checking Cisco Connect it seemed to have a Firmware update which I did and after it was done I decided to do a factory reset since I read somewhere that it works. When the router came back on for a second I saw an unsecured SSID, but then it turned into an SSID called panelist-ssid with a password called google-4panel which is definitely not the default. Also, when I try to access the router webpage to configure it, the password is not the old one nor the default Username: blank Password: admin credentials. I am currently connected to it via the button on the back that allows me to connect without password. Another thing is that I uninstalled Cisco Connect and when I try to install at 25% it says it cannot find my router and ask for SSID + password which I input yet it fails.
View 9 Replies
View Related
Aug 20, 2012
i have a little annoying problem with my E4200. V1 with the latest 04 fw. It seems, that after many hours of downloading at full speed (only one torrent at a time) the speed goes down, and up again, and becoming unstable. My max download speed is 1.5 Mb/s, and it can drop from that, to 50 kb/s, and then up again. and i have no internet access when that happens, but it only last 10-20 seconds and then its back again. Sometimes i get that yellow warning sign on the taskbar which says "No Internet Access" but not always.
Seems like its happening after many hours of downloading at full speed. im on the latest firmware, have tried different channels, 20 Mhz only on Channel Width, different names on the 2.4Ghz and 5Ghz channels.. i use the 2.4Ghz channel btw. Otherwise its stable, and i have had no problems while gaming online.
View 7 Replies
View Related
Dec 21, 2011
I have four E4200's doing the same. I have FiOS 15M download and 5M upload. As soon as QoS is turned on the upload speed drops down to usually 300k and it never exceeds 1M.At the same time any VPN connection gets dropped often.I also configured one E4200v1 as router and the second E4200v1 as Access Point (HDCP off) hardwired to the first one.Any VPN connection gets dropped when changing location. I.e. if VPN was established with the router, the connection gets dropped when in the location where AP is -- and the other way around too. There is no coverage gap between the two locations, to the contrary - they do overlap heavily.On Dec 21, 2011 the level 2 Linksys/Cisco people advised that they will forward the two issues to engineering and that resolution will be within 24-48 hours.
View 5 Replies
View Related
Jul 3, 2012
I've got an E4200v1 running 1.0.04 firmware with guest access enabled. I'd like to find out who is logged in using the guest access. Is there a way to get a list of the DHCP clients on the guest network? I'm able to do this for the non-guest access via the WEB interface's Status->Local Network->DHCP Clients Table page. But I can't find a similar table for the guest network.
View 3 Replies
View Related
Nov 25, 2012
I have an e4200v1 in bridge mode (LAN IP 192.168.1.2) connected via its WAN port to a LAN port on the primary router at 192.168.1.1.
Guest Wireless works perfectly in Ver. 1.0.04 build 11 but not in Ver. 1.0..05 Build 7.
View 9 Replies
View Related
Feb 7, 2011
I am trying to Open some ports on a Linksys E1000. When I run the Shield Up test to see the status of my ports the ones I want to open are closed which is normal but when i try to portforward any port the status goes from closed to stealth. That really does not make any sense to me why when trying to open a port it becomes even more secure then if I did not try to open it. I turned off the firewall and the only thing I see might be the wireless security on the router. I have no idea what that means tho so idk if it is even a firewall.
View 1 Replies
View Related
May 14, 2012
normally i have no trouble opening serten ports for gaming purposes but now i just cant seem to get them open
if i do hyperlobby: (begin: 20999 ) (end: 21001 ) protocol: ( both) on my current ip address and select the active square
it should open port 21000 right?but if i check in game, it wont open, and if i check on internet for port checks it also says timed out, for some reason it wont open this port, also other game ports wont open anymore,not sure what router i got but i think this is the model : WAG120N
View 1 Replies
View Related
Apr 3, 2011
My reports say that my listen ports are blocked even though I removed my router already. I've enabled these ports in Windows firewall already. Why are they still blocked?
View 4 Replies
View Related
