Linksys Wireless Router :: WRT160N Keeps Disabling Wireless Security

Dec 1, 2011

I've had a WRT160N v3 for a couple of years, and I've noticed that the wireless security setting is often set to disabled when I go into the configuration, even though I've set to enabled previously.   It goes like this....
 
I've setup the router to have WPA2 Personal security enabled, with a passphrase.  I have several devices that use wireless that connect to it everyday.  I recently received a new device, so I went into the Linksys configuration to get my passphrase, and the Security is set to disabled.  So, I enable it again, configure a the device, and have no problems. 
 
This has happened many times.  I just happen to be in the router configuration and check the wireless security tab, and it is set to disabled. 
 
My first thought was that maybe there had been a power loss (although, I can't remember the last power outage we had in my area).  However, every other setting was retained, so I can't see why this would be the only one that changes (and it's a rather important setting).  Additionally, I was configuring a blue-ray player last night, trying to see if it was better with a wired setting from another Access Point, and the setting was disabled, so I enabled it again.  I made changes to the BR player, then changed it back to a wireless connection.  I checked the security setting on the Linksys, and AGAIN it was disabled.

View 5 Replies


ADVERTISEMENT

Linksys Wireless Router :: WRT160N - Set A Security Password?

Nov 5, 2011

How do I set a security password.

View 1 Replies View Related

Linksys Wireless Router :: WRT160N - Change A Security Code?

Oct 17, 2012

I have a WRT160N that I've been using with my HDTV for months. Now I want to connect a BluRay player to it, but the setup requires me to enter a security code, and the one I had for the router doesn't work. Can I change the number, or at least double-check the number I do have?

View 4 Replies View Related

Linksys Wireless Router :: WRT160N V3 - Computer Can't Recognize It Whenever Try To Set Up Security Code

Feb 18, 2012

Whenever I try to set up a security code for any of the settings (WEP/WPA etc), as soon as I hit save my computer does not recognize it and I get kicked off the internet and have to restart my router.  I have the Linksys model number WRT160N V3

View 2 Replies View Related

Linksys Wireless Router :: WRT160N V3 Changed Security To WPA2 Personal From WEP

Jun 7, 2012

I recently upgraded the firmware on my wrt 160N v3 and changed the wireless security to WPA2 Personal from WEP (I needed to do this to get higher speeds from a recently purchased wireless adapter).  Now the router stops transmitting a signal intermittently for about a minute before coming back on line.  The time between droppages is also not the same.  Before the firmware upgrade (and the change in security settings) the router was rock solid.  Where I can get the older version of the firmware (which seems to be more stable than the current version)?

View 4 Replies View Related

Linksys Wireless Router :: WRT160N Disabled All Security Or Disable UPNP

May 30, 2011

I have a Nat Strict problem with my router model WRT160N. I want to make a dedicated server with UT3.I tried many things like disabled all security in the router or disable UPNP, fowarding every ports that Unreal Tournament need or DMZ settings. I am running a batch file to start the dedicated server... but still have '' Nat is now strict'' in the log of my batch file. I cant see my server in the master server list inside the UT3 game. I tried to make the server without my router, directly connected to the modem and then it works instantly.

View 9 Replies View Related

Linksys Wireless Router :: Disabling SSID Broadcast On RE1000?

Oct 25, 2011

I just set up a brand new LinksysE4200 router at one end of my home, and a Linksys RE1000 range expander at the other end in order to provide full WiFi coverage to my entire house.  Everything is working great except for one important detail.. There is currently no way to disable SSID broadcast on the RE1000 range expander! I just flashed it with the latest firmware (v1.0.01 build 2, Jul 22, 2011) , but I'm still unable to disable it, even though it is disabled on the E4200 from which it's receiving the signal it's rebroadcasting.  I am seriously considering returning the RE1000. Linksys. add the ability to disable SSID broadcast on the RE1000 in a (not too distant) future firmware upgrade! As far as I'm concerend, this is a MUST HAVE feature in order for this product to even be considered for use in any sensitive network environment.

View 2 Replies View Related

Linksys Wireless Router :: E4200 - VPN Is Disabling Internet Access

Sep 26, 2011

I have a Linksys E4200 router with firmware version 1.0.02. I am using a Macbook Pro. I can connect to a VPN server with the default VPN client software, but it kills my internet connection and disables connecting to SMB

View 5 Replies View Related

Linksys Wireless Router :: Disabling 5GHz Band On E3000

Jul 17, 2011

I've had the wireless G adapter for a year now, and connections work with both 2.4GHz and 5GHz G connections. I just bought a wireless N adapter (2.4GHz and 5GHz capable), and cannot get an N connection.. On 2.4GHz it connects to G only. And on 5GHz, I don't even see the whole band to connect to it.
 
I've tried disabling the 5GHz band on the E3000, then even setting the 2.4GHz band to no security. I still get a G only connection.My laptop can connect to 2.4GHz and get 144Mbps N speeds.Router is at latest firmware.I've researched this online, but can't find anything concrete.

View 7 Replies View Related

Linksys Wireless Router :: E4200 Disabling SSID Broadcast For Both 2.4 And 5GHz Stops Blinking

Jul 1, 2011

I was quite excited about E4200 I got yesterday. Everything works perfect except front LED light start blinking a few hours later. Don't know why it happens in a sudden and non-stop. After several tries, I found that disabling SSID broadcast for both 2.4 and 5GHz stops the blinking.Of course, before doing that, I upgraded firmware to 1.0.02, reset to factory defaults and finally set up E4200 manually rather than using Cisco Connect. Now the LED light is continuously lit.

View 4 Replies View Related

Linksys Wireless Router :: WRT160N Slow Wired And Wireless Connection

May 10, 2013

My WRT160N V3 halves my connection speed (5mbps to 2.7)with both wired and wireless. I have tried changing a lot of settings.

View 4 Replies View Related

Linksys Wireless Router :: WRT160N Not Providing Fast Wireless Speeds?

Jan 26, 2012

I recently bought a WRT160N Wireless router and am not getting fast wireless speeds. My ISP told me my speeds are 10mbps download and 1 mbps upload. I realize that this is not lighting fast but it is all that I feel like i need. My speeds on the WRT160N are about 2-3 MBPS d/l and 600kbps u/l on my wireless connection, which is hooked up to my playstation 3. My wired connection, which goes to my pc, is 9.75 mbps d/l and about .95 mbps u/l, which seems right. Why am I getting such low speeds with a router that is suppose to be build for faster wireless and longer ranges.To make a comparison, I have been using an OLD linksys b-rated router. i can't exactly remember the model, but i think it is the bef11s4, it came with a network card and is about 6-7 years old. I was getting 3-3.5 mbps d/l and 800kbps u/l with the b rated router, and it seemed like a better reception, like in the 80's-90's. ThisWRT160N is getting like in the 70's and sometimes lower.I have tried setting the router to open all ports to a dedicated ip address, it made things a little better, maybe getting 2.5 mbps d/l at the most. What am i doing wrong? I have heard something about tomato firmware but am not real familiar with it?

View 5 Replies View Related

Linksys Wireless Router :: Slow Wireless Transfer Speeds / Wrt160n V3

Jul 21, 2011

I have a home network with a media center.  I have the hauppauge 1212 HD pvr so that I can record video in HD to my hard drive.  I want to stream this content to the differnet PCs on my home network.  Every TV in my home I have hooked an HTPC to it.  I use them to play dvd's.  Stream netflixs etc. My problem is that I am getting a terrible transer rate wirelessly.  600 -750 kbps.  (tested by transfering large files from pc to pc)  All computers have 300Mbps wireless n cards.  all are recieving max signals.  There are either 3 or 4 pc's connected at a time depending on whether my laptop is connected or not.  Obviously this is way to slow to stream video. Made sure my network name is unique.  changed to wireless channel 1 I do think I have WEP 64bit encription could this be an issue?

View 7 Replies View Related

Linksys Wireless Router :: WRT160N-Slow Access Via Wireless Connection?

May 19, 2008

I have a WRT160N with one desktop connected via a lans cable, another desktop connected wireless via WUSB300N and a Laptop connected wireless via WPC600N.

View 6 Replies View Related

Linksys Wireless Router :: Which AP To Use With WRT160N

Jul 29, 2011

I have a router WRT160N and I want to connect an AP using a wireless bridge to enhance my WIFI coverage.Which AP is recommended to use without cable together with the WRT160N?

View 7 Replies View Related

Linksys Wireless Router :: Get Over Wi-Fi With WRT160N

Oct 15, 2012

confirm if the highest speed I can get over WiFi with WRT160N v3 is actually 270 Mbps (and not 300 Mbps as advertised), And there's one more thing - is it normal to have Signal: -51; Noise: -93, SNR: 43, Signal quality 53% if I am only 2 meters far from a router? TX power is set to 28.

View 3 Replies View Related

Linksys Wireless Router :: Can A WRT160N V3 Be Used As A Wireless Access Point

Feb 10, 2010

I have an AT&T broadband router.  A WRT160N is connected to it, so I now have Wireless-N capability.  I have a second WRT160N that I would like to put in my living room as an access point, so I can connect my BluRay player to it and stream video.  How do I set up the second WRT160N as an access point?

View 9 Replies View Related

Linksys Wireless Router :: WRT160N V3 Cuts In And Out

May 1, 2010

I have a wrt160n v3. This is the 3rd one - both the first 2 were defective. I have spent approximately 8 hours troubleshooting the other 2 only to be told they're defective. So, I got a new one. Now, this one keeps cutting in and out. I want as my iPhone constantly switches from 3G to wifi on and over every minute. It really ticks me off! What can I do to fix this? This is a different issue than the original one (very slow) and 2nd (no signal). It's disappointing for a $90 router to do this. I also see the wireless icon on the router flash.

View 6 Replies View Related

Linksys Wireless Router :: Open Nat On A WRT160n V3?

Jan 4, 2012

I have all the ports open necessary and i have upnp enabled.  my modem is a webmaster DPC2100 series. 

View 2 Replies View Related

Linksys Wireless Router :: How To Turn On Wrt160n

Jan 12, 2012

turning my wireless back on. Some how in attempting to create a shared file between my pc and my wife's Mac the wireless has been disabled. I have tried resetting the device several times following the instructions on line however I still can not get the wireless to re activate. I tried reverse directions from the posts on how to turn off the wireless but still no luck. I tried restoring the computer to a later date?

View 2 Replies View Related

Linksys Wireless Router :: How To Reset WRT160N

Dec 5, 2012

How will I reset WRT 160N?

View 1 Replies View Related

Linksys Wireless Router :: WRT160N Won't Connect To Tv

Aug 3, 2012

I'm having an issue getting my tv to start connecting again to the wireless router.Have tried pin setup (timed out & didn't connect...attempted at least 10 times in this fashion)Have tried entering the password (router seems to refuse the connection to the tv)About a month ago, I was in the Network Magic Map & it looked like one of the laptops had been cloned, so I removed it from the network.

View 3 Replies View Related

Linksys Wireless Router :: WRT160N V3 Keeps Disconnecting

Sep 7, 2011

I have a WRT160N v3 Linksys Router and it keeps disconnecting and then reconnecting. It only disconnects wirelessly. LAN still works fine.I have tried a lot of different methods to solve this issue, but none seem to work.I am very dissappointed in the quality of the product. It has done this every since it was bought. I personally would have sent it in for repairs, but others in my household would not have agreed to that.
 
[code]...

View 1 Replies View Related

Linksys Wireless Router :: Can't Register The WRT160N V2

Jul 15, 2011

Just tried to register my WRT160N V2 and when I tried firstly there is no option for the version 2 model and secondly it says my serial No is incorrect when I have tried it three times and have checked it thoroughly.

View 1 Replies View Related

Linksys Wireless Router :: Using Skype With WRT160N?

Aug 21, 2008

While using Skype I am experiencing poor sound quality, sometimes callers are unable to hear me at all and visa versa.  There is a lot of cutting out.  My internet connection is fine. 

View 5 Replies View Related

Linksys Wireless Router :: WRT160N V2 Not Connecting

Oct 12, 2011

I have two PC's hardwired to this router that are working okay (although performance has been choppy lately).  The past 4 days however, when I try to connect wirelessly I get connections that are repeatedly dropped.  I am in the Settings section of my iPad 2 and it keeps rapidly switching between "connected" and "not connected".  Firmware is up to date.

View 4 Replies View Related

Linksys Wireless Router :: Print Through WRT160N?

Aug 5, 2012

Desktop Xp 3 and connected printer, Comcast cable, WRT160N, wireless laptop w/  Xp 3.  Printer is only parallel, and is connected to desktop.  How to setup all and print wirelessly from  laptop through WRT160N to printer on desktop?

View 2 Replies View Related

Linksys Wireless Adapters :: Disabling Wireless On WRT610N?

Sep 22, 2009

I purchased this router so my wife who is recovering from a stroke could access the internet from her bed via her laptop when she's in too much pain to get to her desktop.I am the only person in my area with wireless N. As a result I am being assaulted relentlessly by people trying to steal my bandwidth or worse. In NY the owner of the router is legally responsible for the what the thief does when he's managed to hack into your router. And since this router is dual band; they have twice the opportunity to break down my defenses.Since this router has a 4 port wired switch which I use for all the PC's in the home except the laptop; is there a way to "switch off" the wireless function of the router until such time as it's needed?I have worked with an online advisor to make my router as secure as possible but the shear volume of security breaches makes changing the security settings, passwords; block ip's ect a full time job for a wireless function that is only used some of the time.I would like to be able to switch the wireless on and off at will without affecting the wired connection like I can do on my laptop.I want to make my wife as comfortable as possible but I don't want to get arrested because some wireless theif broke into my router and used it to download kiddieporn or whatever with my ip address.

View 8 Replies View Related

Linksys Wireless Router :: Connect IPAD To WRT160n?

Feb 23, 2012

How do I connect IPAD to Linksys router WRT160n?

View 2 Replies View Related

Linksys Wireless Router :: Using WRT160N V2 As Access Point?

Mar 22, 2013

I have a FIOS setup with their Router/modem providing DHCP and Wireless routing.  The problem I have is that I have a mix of older equipment and newer equipment.  The newer equipment is capable of supporting WPA2, the older is not.  I would like the benefits of WPA2, but still would like to at times be able to use the older equipment.My solution was to use a WRT160N v2 router that I had as an access point and it also gives me switch capabilities for wired systems as the FIOS router in on a different floor than the Linksys router.  Wired access works just fine and the wireless worked fine until just recently.Since both routers have the same default IP addresses I changed the Linksys to a different static IP and turned off DHCP.  I left all of the other defaults the same.  I set up the Linksys for WEP and created the key for security.  Everything worked fine for the better part of a year, but recently I am having problems where some of the computers cannot find the network or find it then lose connection.

View 9 Replies View Related

Linksys Wireless Router :: Difference Between WRT120N And WRT160N

Jul 29, 2011

I am considering to purchase a Linksys Wireless router, but I just don't know which one to select.There are so many different types that seem to have very similar (if not equal) specs.If I just limit myself to the WRT120N, the WRT160N and the E1000, they all have 4 ethernet ports (10/100), and they all support 802.11 b/g/n for the wireless part.Obviously they all promise a blazing performance, and wireless coverage throughout the whole house, without (many) blind spots.But if their specs are the same, why are they different types?

View 2 Replies View Related

Linksys Wireless Router :: WRT160N V2 Connects For A Few Seconds Only

Sep 9, 2011

I have a WRT 160N v2 router. There's 1 computer wired to it, that works fine.  Then I have 2 laptops and a pc wireless to it.  One laptop is a mac and that seems to be fine, another is a Compaq notebook that has trouble connecting and the pc has the same problem.  The signal strength is very good to excellent so thats not the issue.  What happens with the pc is, it will connect but at times its only for a few seconds then it disconnects.  Sometimes restarting the computer fixes it for a while but it will eventually start having the problem again.  It detects the wireless network just fine, and the router's firmware is up to date.  I have a feeling that its the settings in the router but im not sure what to change. 

View 3 Replies View Related

Linksys Wireless Router :: WRT160N Can't Connect With Laptops

May 31, 2008

I have two computers on hard line and two laptops. All computers on the line work fine and flawlessly. But when I try to connect the laptops to the computer, they say there's a problem with the certificate. Both detect the connection, and with strong enough signal strength. I've tried WPA and WEP encryption methods, and disabling encryption methods. All had no change. I believe the problem lies with this Wi-Fi Protected Setup stuff, which I have no clue as to what the hell it's supposed to do. I've tried disabling it by turning it to manual, which all computers then lose internet connection entirely. Browsing the FAQ's, I havn't found a solution. I've been working on this thing for a solid 7 and a half hours straight, and phone support is trying to make me configure static IPs, which proved extremely inconvenient in the past.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved