I'm currently on my home network, which used to consist of a router with wifi and all had a stable connection. However after leaving for university, i have come back to find that they are using these : (it now says i am connected via LAN) - i am running via a ''powerline network'' apparantly.
[url]...
However I believe my dad's internet is hardwired to the router, which is where the problem lies. When his pc is off, the internet is fine, however when he turns it on the internet becomes VERY intermittant for everyone except for him. When downloading a file it cuts down to 40-50kbps (not much slower than it usually is), but drops out every half a second... This makes web browsing impossible, let alone anything else.
Is there a way to monitor network traffic speeds. Our companies network download speeds seem to start high, but then progressively slows to a near stop.Downloading small documents start out fast and finishes, but I noticed that the speed slows down significantly. This poses a problem when downloading larger files and documentsThe speed start out very high, but then slows to near zero and results in the file failing to complete.What i need is to find out what is causing the speed degradation and or where our bottleneck is. Is this a setting issue with the browser, security, etc.
Over the past few weeks I have noticed that our internet has been running slowly, phoned ISP and did the usual tests and they discovered nothing wrong with line etc.I therefore started monitoring our small network and noticed when a user uploads files to the internet, even small ones, the internet connections slows down significantly. I obviously would expect some noticeable change, but this is almost killing the connection all together... pain for other users considering we're an web design coThe users are connected over a network using a Netgear JGS524 Switch, which is unmanaged. The router is a Netgear DG834N. We do have several users, a printer and a Qnap server connected to it... maybe all the activity is slowing the internet, but can't see why it would only start affecting the network in the last week?
I have a Wireless-N router, and all of my devices use Wireless-N with the exception of my wireless printer (Brother HL-2170W), which only supports Wireless-G.I seem to recall reading that only one Wireless-G device can slow the entire Wireless-N-capable network to G speeds. Is this so? If so, would the slowdown occur only while using the wireless printer?
I want to add a cisco or netgear powerline adapter to a building.I have read that for home it works really good, but i am going to add it to a building--A 5 floors building.So i would like to know if anyone has done this before and it works. This is a commercial building.And it is not easy to run cables, that would be the second option if the powerline do not work well.
Here is what a wired portion of my network looks like:
internet---dsl modem---airport extreme---powerline ethernet adapter****powerline ethernet adapter---5 port switch---(ip camera & ioBridge 204)
The airport extreme is also hardwired to a PC that I use to view the IP camera.The issue I'm having is with the connection to the IP Camera.The connection to the camera worked for a long time, then starting dropping periodically and now it doesn't work at all.The ioBridge connected to the same switch as the camera connects to my network and the internet just fine.
Here's what I've done to troubleshoot: I plugged the camera in to my airport extreme and it worked fine. When I plug my camera into the other end of the powerline ethernet adapters, though, it doesn't work (even though the ioBridge does). I replaced the powerline adapters today (because they had worked before, so I guessed something had fried in them) but the connection still doesn't work.
When I ping the camera (when it's on the other side of powerline adapters and "not working") the response time is around 3ms (good) but there is about a 33% loss rate (bad).I'm guessing it's the loss rate that is keeping it from displaying the video stream on the computer...but I can't think of what changed between when it was working and when it stopped working that would cause it lose packets like that.
I have a duplex home in an urban setting that seems too vast for a single wifi router. Additionally, it seems that there is significant speed degradation through wifi. According to my speed tests, I can lose up to 70% of my contracted internet speeds (of 15 mbps) via the router (which I am hoping that the Apple TC can fix although I'm sure that sometimes it's the cable co's fault!)I have read that if I can add a wifi router to the second floor that would work with the signal, however that speed would be the same degraded one.So, I have been doing lots of reading on the Powerline devices and I'd like to know if I can do the following and if so, how:
1. Connect the wifi router (soon to be an Apple TC) to the cable modem, as I do now, but then run the ethernet cable through the TC to the Powerline and Powerline network that way.
2. Connect my iMac to the internet via Powerline
2a. Can I then use Powerline fo Home Sharing, Air Play, and so on?
2b. Back up my iMac to TC?
3. Connect my internet ready TV via Powerline (currently conencted via wifi).
4. Connect a second wifi router on the second floor via Powerline and it be on the same wifi network as if I am using the second router as an extender.
5. There is a tenant on the 3rd floor who receives a separate electric bill. Can I assume that they would be shut out of my Powerlined network?
I have cable internet with a speed plan in the 10-15 mbps range. I have a wireless Belkin g router that is several years old. Connected to the router I have my cable modem as well as my PS3. I connect wirelessly from my PC to the internet, as my PC is in the other room (more on that later). When I'm streaming movies via WiFi to my TV, the connection is highly unstable. Some days, I will not experience any stuttering (or very minor stuttering), whereas other times the stuttering is almost unbearable. Last night, I had trouble streaming a DVD quality movie whenever it went above 2 mbps total bitrate. Other times, I can stream HD movies without much stuttering (except for very action packed scenes).Interestingly, I stream Netflix movies over my PS3 via a *wired* connection. Last night, I conducted a speed test on my PS3. First, I had the PS3 plugged into the wireless router. I achieved speeds around 2 - 4 mbps on average. I then plugged my PS3 directly into my modem and achieved speeds around 10 mbps! The boost was instantaneous. I should note that on my PC, I speed test regularly over the WiFi and achieve around 4-6 mbps on average (only once did I achieve 11 mbps).
I have a belkin N300 router that works decent most of the time, but anytime my roommate connects with her macbook pro the whole network becomes slow to the point of uselessness. If i block her computer using mac address filtering, the latency and download speeds are right where they should be, but as soon as i allow her back on ping jumps to 800-1000 and DL speeds drop to under 1mb.
I would like to set up a TV in my spare room which does not have a coax plug. Because of the set of my house running coax cable to this room, although possible, is something I am hoping to avoid. This is because if I was to run the cable on the outside of the wall it would get in my way and it will cost $300 to $400 for a tech to come out and run it through the wall.My first thought was to set up an old computer in my living room and have it connect to a cable box. Then I would send the video signal over the wireless network. The problem is that I cannot change channels on the other end. I have been reading up on power-line networking and it looks like a good option for my problem. I was hoping to find a device that will allow me to plug coax cable into it in the living room send the signal through the power-line to another device in my spare room where my TV receiver would be located. Is there anything like this out there on the market? If not are there any other options I can look at?
I'm planning to build a network in a office and I've decided to do that with powerline AV network adapters.I
1. what is the real limit of numbers of powerline AV adapters in one network?
2. what if my neighbours are planning to build their own network and total number of adapters in building exceeds the maximum possible number. How to filter powerline networks from each other?
I have two netgear powerline AV 500 ethernet adapters that give me near ideal internet access on my media computer (FIOS 25/25mpbs tests out at 8ms 25.4/24.7) and perhaps 100-140mbps to my router, printer, drive, etc. I now want to add a few wifi points and instead of having the mess of a powerline adapter + a wifi router I think it will be neater to have an all in one solution. Most of the ones that I find are 200mbps, however. I know that 500 is backwards compatible, but will a mixed solution slow everything down like it can for a mixed wireless g/n network?
I am trying to connect a sony blu-ray player to the internet using a powerline adapter but the BR player does not connect. I currently have two Satellite DVR receivers using the same powerlines and they work fine, but the Sony player does not connect to the network. I have to try a wired connection because my wireless signal to the player has trouble with netflix and other download services. Connection gets lost.
my goal is to share my cable modem signal over my two story house using two wireless routers. The delima is that the routers don't support wireless bridging and if they did, the signal is too weak to make it worth while.
The remedy I came up with... buy a pair of powerline network adapters and connect one router to the other so I could have a good signal upstairs and then a good signal downstairs.
Downstairs, I have the cable modem connected to the Linksys WRT54G router, which has a line out to my blu ray player, wirelessly feeds a PC downstairs and then has a cable run to the powerline adapter.
Upstairs, I have a cat5 connecting the powerline adapter (which was tested and works with laptop) to the data input port on my second wireless router, the netgear wndr3400.
I can't get the netgear upstairs to pull an IP address from the linksys router downstairs over the powerline network.
I'm using a Linksys E1500 on my Timewarner 20Mbs connection and I've noticed that anytime another computer on my network connects my connection speed take a significant drop. This happens when Macs or PCs connect and there doesn't seem to be any common ground between any of them. In addition the connection is slow wether the other PCs are idle or downloading anything, it seems to make no difference. my ping in any game drops from 70 to 500 just for 2 other PC being on at the saem time on the network.
I have a home network running all Mac computers (though can run Windows VM if necessary) and a pair of USB printers. The wireless router and cable modem are in one room, but the printers are in another. I'd like to find the most practical way to add the printers to the local wireless network without sharing them from a computer. I've tried that for a while, but don't want to leave a laptop connected 24/7 just to enable wireless printing (rather defeats the purpose of a portable computer). I don't have any wired network lines in the home, and am not excited by the idea of running any cables.
I have a question about my windows systems(XP and Vista) re-connecting to my network folders when my computers restart. I have some shared network folders on my Synology DS410. And then i mapped a network drive to use those folders.But every time i restart my computer i get the message "cannot reconncet all network drives"I have to put in my username and password everytime. I choose Remember login and password.How can i fix this so it automatically connects to these on restart?
FYI... 1 computer - Windows Vista Home Premium 1 computer - Windows XP Home Both connected via wired LAN
My iSCSI drives connect just fine on restart. Just not my mapped network folders.
My computer is a 32 bit, Win7 SP1 with Pentium Dual Core 2.6 Ghz and 2Gb of Ram on a wired network. My wife has a similar system using a wireless network. She can ping my IP Address, but I cannot ping hers. We both have full access to the Internet. We are using the same workgroup, and both computers have file and printer sharing enabled and IPv6 addresses and DNS server addresses selected automatically.The problem appears to be with my computer?
Here are my system stats:
Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 32 bit Processor: Pentium(R) Dual-Core CPU E5300 @ 2.60GHz, x64 Family 6 Model 23 Stepping 10 Processor Count: 2 RAM: 2013 Mb Graphics Card: Intel(R) G41 Express Chipset, 782 Mb Hard Drives: C: Total - 76308 MB, Free - 49226 MB; D: Total - 286167 MB, Free - 52893 MB; M: Total - 38154 MB, Free - 7 MB; Motherboard: ASUSTeK Computer INC., P5G41-M LE Antivirus: Microsoft Security Essentials, Updated and Enabled
When I plug in my Belkin my Netbios over TCP/IP is enabled, however is disabled when the router is connected. I cannot gain access to internet through Belkin G router, but can through my ISP router. I've tried IP/Config/all, (Nothing). The problem started when I changed something in Firefox (About:Config) attempting to change URL Search engine from Yahoo to Google, and that's when the problems started.Now my (Desktop) Computer doesn't recognize network, and I can no longer gain access to Net w/Belkin G wireless router...however, router will allow temporary access to internet when plugged up anyway (2 Android phones, 2 laptops), but the desktop will not connect.
I have a desktop computer that as of last night worked with the internest. This morning it did not. I have a home network. I also have laptops connected to a wireless router and they have no problem getting into the internet. Not sure waht to do. I am running Windows Vista Home Premium.
new HP 2000 computer he just purchased. I brought it to my house to set it up. No problems connecting to wifi at my home. Downloaded all the updates and got it ready for his house. When I tried connecting to his network, it kept giving me the network key. I know I was entering the correct information because we had his older computer and I copied the exact thing. I had also made a folder when I set up his other computer with his information for his network in it and I was going by that. I tried to automatically connect and I also tried to manually connect. I deleted the name of my network (that worked) and rebooted. It continually gives me the block to put the password in. I brought it back to my house and the wifi connected with no problems. His old toshiba had no problems connecting to his network. I disconnected it and reconnected it. Is there something about the settings I am not doing? Or is it a firewall setting? Is there something in the modem that is conflicting with the new HP. It's a WAP2 Personal with AES Encryption (did not work on that one), where as my network is a WPA Personal with TKIP Encryption (worked on this one). Will that make a difference and if so what do I do about it?
I am on network with administrative rights and one computer on network is not visible in ipscanner, cannot connect with remote desktop connection. Cant even connect by typing in run command (eg. \192.168.1.10c$) The computer is ON and users have logged on it many times. This same problem happens on many other computers too, and its not permanent. After few days or so, he problem is gone, and sometimes persists after a weekend, when pc is shutdown on Friday. Operating system is windows xp sp2 and there is no third party firewall on remote computers.
I would like to know if any of you know how to do a documentation of a network (Computer Network) in the topics of Remote Application, Users, and Group Policy.I have been trying to look for examples of documentations of those topics, but nothing.
I recently got a new computer from work, and it won't connect to my home network. I restored it to factory condition, and reinstalled the drivers for the wireless adapter card, but it won't identify my home network. The network adapter is a D-Link WDA 1320 and I'm trying to connect it to my home network which is AT&T Uverse, and the router is a 2wire 3800hgv-b. Hopefully that is enough information for at least an educated guess, I'm not so hot when it comes to home networking matters.This doesn't happen on any other computer.
So I've had this problem ever since I bought my computer. The only wireless connection that I am able to connect to, is the one in my home. If i travel anywhere else, my laptop refuses to let me connect. The thing is, my laptop sees the connections, but when I click "connect", the box closes and nothing happens. The laptop seems as though it doesn't even try to connect to the network. Everything remains the same, yet when I come to my house, it connects automatically. Now if I click "Add" on the network config. it won't even let me add a network to my computer or anything. I click the "Add" button and nothing happens. I am running a Windows XP.
I have a laptop (win7) and desktop (vista) in a network. The laptop is wireless and the desktop is hard-wired into a d-link router. My computer recently updated and since then I cannot connect to my desktop from my laptop. The desktop shows up in the network map but when I click it, it hangs and says "network path not found". I can ping the IP and the name of the PC from command line but I cannot access it. I have internet connectivity the whole time regardless and I've tried multiple routers.
I can't find the third computer on my network. All the computers connect to the internet but only the two XP computers show up via my network places. I try to setup an office network on all of the computers to see if it works. I can still only get the XP computers to connect. My main goal is to be able to create a private network to share files between the 3 computers. This is for a small office in a corporate building so it has to be private.The third computer is running on Vista which I don't know how to use at all as I only have win7/xp at my house.
I've got 3 identical PC's that were bought and configured at the same time, all running Windows 7 off a Netgear router. Though all 3 machines can successfully ping each other, one machine can't be accessed by the other two through windows explorer meaning it can't participate in LAN games or share files with the other 2 machines.
I also seem unable to register my copy of Starcraft II because it doesn't recognise any return data from the Starcraft servers, though it works fine on another machine (not sure if this is related). I've disabled the firewall on the unaccessible machine and believe file sharing is activated but it hasn't worked.