We have a FortiGate 300C firewall and I was trying to allocate an external IP to an internal IP and I was having a lot of trouble figuring out exactly how to do that.
View 1 RepliesI have one Fortigate 200B Fire wall, which is using for wifi internet. i had configured one login page in the fourtigate .The path following below system > config > replacement message > authentication > login page.
it was working earlier. suddenly its not working. when i checked this path, that login page message colum was blanked. when i trying to put the message again its not pasting and am unble to type the message also.
I'm using Fortigate 200A firmware Versionv4.0.3,build0106,090616 and IPS Definitions 2.00673 (Updated 2009-08-11).
View 1 Replies View RelatedI need remote access to certain programs on my home PC but I just cannot get it to work.
Program:- webcamXP
When I set the programs port preferences (i.e. port 8087), I can connect with"127.0.0.1:8087" and webcamXP work fine. But when I replace the localhost with my external IP (lets say 79.149.114.227, so that would be "http://79.149.114.227:8087".I tried port forwarding: I have added the port to my NAT in the router's setting so it should be fine, but it is not (numbers are fictual of course):
external port start 8085,
external port end 8089,
protocol TCP/UDP,
internal port start 8085,
internal port end 8089,
server IP address 192.168.1.215)
I also tried disabling AVG Internet Security 2011's firewall temporarily just to check it it was blocking it, but got the same result.I checked if Windows own firewall was on, but it is off.I cannot find any setting in the router's own configuration screen to disable any build in (router's) firewall (if it has any).
I have an internal DVR system that I am trying to share to the outside world. We recently put in an ASA5505 and I am having trouble getting the settings correct.I want to use an external IP to access the DVR system from anywhere and have my ASA5505 redirect the traffic to the internal IP address. I assume I need to use a NAT and a route policy however can not figure out how it would be.
View 11 Replies View Related6509-E compact flash Internal vs External
View 1 Replies View Relatedwe recently upgraded from an RVS4000 router which didn't have this issue.
the problem; Internal users from Site A cannot access the external owa address.From Site A i can successfully ping both the external/internal IP addresses/names and they resolve correctly, including pinging the address ('mail.company.com") resolves correctly to the external ip address.
[code]...
i need replace a Fortigate 310B with Cisco products, that is, all Web Filtering, IPS/IDS, AV, so, the question is, what we can use to replace?First, we can use Cisco ASA 5520 right? with CSC Module, so, this for Anti-X, but for IPS? is better router with IPS on IOS? or IPS Sensor? or other Cisco ASA with IPS Module?
View 3 Replies View RelatedIs it true that the FCC is investigating the Pogo game site because of poor security? Is Java the cause of this problem?I'm very leery of getting on the Pogo site because I've been told that my computer could get a virus and crash.
View 1 Replies View RelatedI'm new to IT, and have been put in charge of managing our servers hile my boss is on vacation.We currently have a Sonicwall Network Security Appliance that handles our Firewall/VPN and have web content filtering set in place.I have a user who belongs to 2 CFS policy groups that we have set up. I've double checked with Active Directory, and he is a member of both groups.
This person SHOULD have access to Job searches/ and Restaurants,but receives a "content blocked" message on his browser.It appears to me that the settings in Sonicwall are correct, as well with AD member groups.
I am trying to connect to a Security-enabled wireless netowork. I have the key. My problem is that I can't seem to figure out how to enter it. When I try to connect I open the "view available networks"window. I see the network name and it shows a strong signal (all 5 green bars).
View 3 Replies View RelatedI want to install Microsoft Security Essential on my PC, but I am not sure which download I need. One says amd64 and the other is x86. I am using windows xp 32bit.
View 2 Replies View RelatedSome security tools and techniques for wireless LAN??
View 1 Replies View RelatedHow can I get the security key password for my iPad?
View 2 Replies View RelatedI have windows xp home and the last few days a security installation has kept trying to install ie: "Microsoft Visual C++ 2005 Service Pack 1 Redistributable Package (KB2538242) (update 1 of 1)..."
View 3 Replies View RelatedI have a checkpoint Safe@Office 500 firewall router, connected to adsl via another adsl device in bridged mode.We needed to assign an external IP to a device behind the firewall.We contacted the ISP, and now they have assigned an additional IP to our adsl account.I have read from the documentation that:"NAT can be defined automatically via the network object (Node, Network or Address Range). When you define NAT via the network object, rules are automatically added to the Address Translation Rule Base"....so I add the object, with the external IP given to us by our ISP, and the wizard simply complains that the IP address is invalid.My thoughts are that the router does not know about the additional IP provided by our ISP. If so, how do I tell the router that there are other IP addresses available to use? I have rebooted the router, and no luck.
View 1 Replies View Relatedi can can ping my host externally from another ip however i have left my house without port forwarding to my pc is there a way to connect to my pc via something like this command "xxxx.dyndns-home.com:192.168.1.100" i have tried this and does not work as it does not like the ":"truth be told my real goal is to ultimately be able to look at my webcam as it is pointed at a homebrewing project which i need to see. this is what i want to work on setting up while in rdp?
View 2 Replies View RelatedI found a link to accomplish this on the old code but how can I get this done on 8.4.
[URL]
I have a 2600 I am trying to setup for educational use.
My Cable ISP has issued me 5 routable IP's through their SMC modem 86.28.12.226-229. The SMC modem is .225. Currently the internal network can get out through .229 as expected but nothing outside (tcp 80 to web server) can get through. When I assigned the ip's to e0/1 as secondarr I could get it to route from the inside network (so hitting .226 80 went to the correct place) but it still didn't work from the outside - plus I read that wasn't a great way to do it anyway.
!
interface FastEthernet0/0
description LAN Interface
[Code].....
Our secondary site accesses the internal intranet via a link, which is basically:
[URL] where externalip is the IP address of my router.
* This used to work fine before we migrated from ADSL (6mb up / 0.5mb down) to Fibre(70mb / 20mb) *
Internally, I access the same link, but via [URL] Internally it loads in 2 seconds, externally it is taking 68seconds(ish)..
I can't work it out, the fibre shouldave made things loads quicker but is infact very slow. I'm wondering if something network wise is going on.
The intranet is a php intranet sitting on apache, and using postgresql as the database. Other pages load fine, this specific index.php page does quite a lot of DB connections and so on, but as I say before, it worked fine before the migration.
I can hear nothing sound driver disabled... windows explorer wont open...and my notepad and calculator wont work either... how do i remove it..
View 1 Replies View RelatedWe are currently in a position to be needing an ASA series firewall. We currently have dual redundant Fortinet 300C's in place. The reason we are wanting the ASA series is the way we are designing our VOIP system is we will be utilizing the 9900 series cisco phones with the any connect VPN. We are also going to structure our BYOD deployment around the any connect VPN.
My first step is to find an ASA firewall that is comparable to the 300C's that we have now.
We have 350 "internal" clients on an MPLS network at 20 remote sites. All of the internet to these sites comes back to our HQ where the firewalls are located. The MPLS is 30Mbps to the internal and 15Mbps to the internet. The fortinets do web content filtering, traffic logging, DMZ separation, NAT, and we will replace our Juniper SA2000 VPN with the ASA firewall as well. We are looking at roughly 125 VPN clients.
The problem is that the PABX is sending out an internal address in it's INVITE messages and the ASA5505 isn't changing the internal address to the external address.We need> From: Calling Number <SIP: SIP Username@Public IP Address>However our PABX sends out> From: Calling Number <SIP: SIP Username@Private IP Address>. How to translate the internal IP address to the external IP address on an ASA 5505?
View 1 Replies View RelatedI am converting from a Cisco Model 850 to a RV042, all is well so far but I cannot implement one feature I had on the old router.I want to do one to one nat from one internal ip to one external ip but I only want to use one tcp/ip port.The command to do this on the old cisco 850 was this:"ip nat inside source static tcp 192.168.1.181 80 75.xxx.xxx.181 80 extendable"Can this be done with the RV042?I can do one to one nat but it include all ports.
View 1 Replies View RelatedI am wondering if the folowing is a valid configuration:
WLC2504
AP2600
I need 3 SSID/VLAN, 1 for corporate devices, 1 for coporate smartphones, 1 for guest.
Port 1 on the 2504 should be used for management and corporate devices and connect to the corp network. Port 2 is for smartphones/guest and will be connected to a Cisco ASA 5515 that is connected to a second ISP.
Corp devices should get IP from an Windows DHCP. Smartphones/guest should get IP from the WLC. Is this possilbe? I read this in a document "To use the WLC as a dhcp, you need to enable DHCP proxy as it is required." Some how I am imagining that this will mess with the Windows DHCP. Is it better to use the ASA as DHCP for smartphones/guest?
I have 3 external ips from my isp:
222.222.222.221
222.222.222.222
222.222.222.223
The first one I use to provide internet access to my office. The other two I'm going to use for the following: I'm going to deploy a server in internal network which must have 2 external ips on his network interface (& one internal ip on the second,but that's ok: I cannot put an extra network switch before asa & plug this server there: this server is virtual & is on esxi host in internal network. External ips must be assigned to servers' interfacw,bot just forwarded there (ms direct access requirement).
My current config:
!
ASA Version 8.4(3)
!
hostname msk-office
[Code]....
I have Astaro UTM running on an old computer as my only firewall right now. The Astaro also serves as my DHCP server. My Wifi is provided by a Linksys E3000 running DD-WRT software. NAT/SPI are disabled on the E3000, and it forwards DHCP requests to the Astaro. All my network clients connect via wifi/ethernet to the E3000.
All clients --> E3000 (no firewall) --> Astaro --> www
I am considering setting up my own personal cloud server using a Synology NAS that I can access remotely. I would also like to remotely access my Surveillance DVR. I would like to access them via VPN or portforwarding. I do not want to use DMZ.
I would like to utilize the SPI firewall on the E3000 to provide an extra layer of defense. I would like the NAS and the DVR to be on an external LAN between the Astaro and the E3000...and all other clients being on an internal LAN behind the E3000. I have the necessary switches/cables to make this work.
My question is...How do I configure the E3000? Can I have both the internal and external LANs on the same subnet? Do I have to use the NAT on the E3000? I'd rather not...since that will render the Astaro's reporting functions rather worthless.
I would like the Astaro to remain the only DHCP server. I would like all internal LAN clients to be able to reach out to the external LAN/WAN...but the external LAN should not be able to reach into the Internal.
I have a hosted web server that has a website on it that needs to connect back to a database within our internal network. We have a Cisco WRVS4400N Wireless Router with 2 VLANS. VLAN 1 goes to a Watchguard Firebox which is connected to our internal network. VLAN 2 goues to our classroom network.
Our database is on VLAN 1. I have opened port 1433 on the Watchguard to allow SQL traffic from our Web Server. I can telnet from my workstation on VLAN 1 to the Web Server over port 1433, so I know the Web Server is not blocking anything. When I try to telnet from the Web Server to our Public IP address over port 1433, it fails.
I believe I have the firewall on the Cisco WRVS4400N off, so it shouldn't be blocking any traffic, but for the life of me I can't get this to work. I have been working on this for two days, and I NEED it to work. This was working up until last week, then it quit working. I am the only person making changes to our network, and there were no changes made during that time.
I have a Cisco 5505, 2 sites that are internal, 1 external IP (dhcp from cable modem). While on my laptop, ipad, iphone, I cannot access the server via it's external IP address. I MUST use the internal IP in order to access this site. I have heard of hairpinning, internal dns server(don't really want this).
View 8 Replies View RelatedI am aware that we can allow external admins to telnet over a custom port to the internal router. Even i was allowed to connect to a remote router via the remote firewall. The way i was accessing the router is by telnet to the remote ASA address on port 8023.I am not sure how exactly we can configure this on a ASA.
View 2 Replies View RelatedI have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
View 5 Replies View RelatedI was just wondering if it's possible with an ASA 5510 to connect to the external IP address of an internal server from inside the network. I have already set up dns doctoring for dns lookups, and everything is working fine there. We have an application inside the network that tries to connect straight to the external Ip of another internal server. where to look in the ASDM 6.4?
View 2 Replies View RelatedI am having an issue with internal and external clients. When we have the nat ip configured on the controller we cannot connect internal ap's at all. When we take the nat ip out it works fine. We are on code 7.0.220. I have tried the following command <config network ap-discovery nat-ip-only disable> and it did nothing.
View 1 Replies View Related