If a copy a file from my desktop to my laptop, the speed is usually 3 or 4 times faster than if I go in the other direction.
Desktop is connected to the router by a cable, laptop is wifi.
If I connect the laptop with a cable, speeds are fast both directions.
Router is a wrt54gl with dd-wrt. Both machines running Win7
Why would this happen? How can I identify the problem and fix it?
am having speed issues on the wireless side of my WRT54GL v1.1 router.When I hook up a laptop to the wired port, am getting roughly 5.4mps down when wired, but only 1.2mpbs down on wireless. I am tried doing a factory restore. I have made sure that no QoS is in place. I have tried multiple devices to make sure it is not something on the device side causing this problem, but all the devices perform just as poorly on wireless but as well on wired.
View 5 Replies View RelatedI have NM-16ESW card installed in one of my 3845 router. Below is the sh inventory output
NAME: "16 Port 10BaseT/100BaseTX EtherSwitch", DESCR: "16 Port 10BaseT/100BaseTX EtherSwitch"
PID: NM-16ESW , VID: V01 , SN: FOC11482484
NAME: "Gigabit(1000BaseT) module for EtherSwitch NM", DESCR: "Gigabit(1000BaseT) module for EtherSwitch NM"
PID: GE-DCARD-ESW , VID: V01 , SN: FOC11454FW6
Is the Gig port available here can be used for uplink?I found following comment at
[URL]...
"GE-DCARD-ESW: This optional 1000BaseT Gigabit Ethernet port for NM-16ESW and NMD-36-ESW can be used for a gigabit connection for a file server or for intra-chassis stacking of the Cisco EtherSwitch module. Stacking is supported in Cisco IOS release 12.2(11)T and beyond"
I'm just wondering how I would get a faster upload rate. Is it my modem? Is it my internet connection? At the moment my upload rate is
View 4 Replies View RelatedI have a BEFCMU10 version 2.0 cable modem. My provider Insight Broadband has recently boosted their internet speeds. But I have found out that if my modem is not DOCSIS 2.0 compliant, I cannot get the faster speeds. How do I know if it is DOCSIS 1.1 or DOCSIS 2.0 compliant? I hope I don't have to replace the modem as it has given me absolutely no trouble since I have had it.
View 9 Replies View RelatedI cant figure it out and can not find a solution. All three computers have gigabit nics, I have gigabit router and switch, my d-link 321 is set to gigabit, the only thing on my network that is not gigabit is my printer. I'm not getting gigabit transfer speed from my computer to dlink 321. I rarely do computer to computer transfers, so I dont know what the speed is of that. The best tranfer rate is from 7-12mb. I am also using cat 5e wires on all connections. What am I missing?
View 12 Replies View RelatedSwapped wireless routers 150mbps for 300 mbps mimo for faster speed Will I see that additional speed on my wireless LAN?IOW, what conditions must be met before I can reap additional speed with my 11g laptop or my 11n hp Touchpad running both webOS and CyanogenMode 9?
Swapped
Rosewill RNX-N150RT 802.11b/g/n
for
Rosewill RNX-N300RT 802.11b/g/n(2T2R MiMo)
Have high speed cable and find that the wireless speeds using Speedtest.net are faster than when hooking directly into the E4200. Do I have something set incorrectly?
View 3 Replies View RelatedI purchased a new laptop (wireless-n). However, the old laptop I have from 6 six years ago (wireless g) has a faster wireless connection than the new one (20-25 mbps vs. 0.50-1.00 mbps). The 2 computers are at the same location in the house in regards to the router.
View 12 Replies View RelatedI have a 16mbps (megabits) cable modem that is connected to WRT54GL. Desktop is located next to router and is connected with a cable, Laptop is connected on Wi-Fi. Both PCs achieve maximum speed when downloading from the internet but when I try to copy something from one PC to another over the local network I get stuck on max 2.5-3MBps (megabytes).
View 4 Replies View RelatedI have a Linksys WRT54GL v. 1.1 that has been dropping connection speed (starts at 54mb, then drops to 48mbs, 36mbs, 28mbs, down to 1mbs) then disconnects, then reconnects at 54 mbs. After a short while, it will drop the speed again until it disconnects and reconnects again. This is the third Linksys WRT54GL that has done this. The first one was 5 years old before it started doing this in February, the second was 3 months old, and now the replacement Linksys sent to me is doing this?
What is going on with my router? I am able to connect fine with the Cat5 cable, but wireless seems to be the problem. Even my phone(s) get disconnected from the wireless router. This problem just recently started and I don't know why, no settings had been changed on any of the routers until after the problem had already ocurred, then the Linksys phone tech support had me make multiple changes.
Router: WRT54GL v1.1
Firmware: Tomato 1.28.1816
OS: Windows 7 Professional
Wireless adapter: Atheros AR9285 Wireless Network Adapter
I upgraded my Internet speed with my ISP to 60Mbit/s and I get following download results at speedtest.net:Is there a way to speed up my wireless connection with this router? On the sticker it says 54Mbps, so I would guess it should be possible.
My ISP provides me internet by pppoe connection.When testing the connection with the router i get 30 mbps.When testing the conection without the router, cable conected to laptop i get 60 mpbs.
View 1 Replies View RelatedMy internetprovider increased speed from 25 Mbps to 40 Mbps. Providermodem direct to pc via LAN gives indeed speed 40 Mbps. However through router lanport or wireless no higher speed. How comes?
View 2 Replies View RelatedI just installed a Belkin N150 wireless router to use with our iPhones which it is working great. But I also have my desktop pc attached to the router as a wired connection and the down load speed on the desktop pc has decreased dramatically. for example it took 10 minutes to download a 30 sec video.Before I installed the Belkin router I had no downloading issues. This is on a dial up modem.
View 5 Replies View RelatedWe have configure a L2L vpn between Asa and 1841 router. We are facing this issue.The tunnel is not getting up from the 1841 site never. When we are trying to generate traffic from the ASA site the tunnel is up and we can see decryps and encryps packets.
Router 1841 Config:
crypto isakmp policy 100
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key * address 213.249.XX.XX
[code].....
I'm using a couple of ASA5510's since a few years in a few datacenters, and I wonder about the following:
Usually the ASA's are positioned with the connectors facing to the back of the 19" cabinets, so one can easily connect the device to other networking-hardware. In many datacenters nowadays, cold-coridors are used, which results in a forced airflow through the cabinet, which is empowered by the fans in the servers itself. But the ASA's are permanently blowing air in the opposite direction, and are also taking the air from the part of the cabinet where the air is as hot as it gets.
Is it a good practice to open up the ASA and flip the fans 180 degrees to solve this?
I have to replace a 1230 with an 1262 AP.
All antennas have to be in the same direction on the AP and I guess when the old 1230 is working well the 1262 will be only better . Attached u see how I plan to mount the new AP versus the old one...
I'm very new to cisco devices but we recently acquired a catalyst 2911 device for our co-lo cabinet and I am trying to get a site-to-site vpn connection working between the facility and my offices network as well as a remote access VPN for me to use in case I have to fix something while outside of the office.
The office's gateway is 66.119.163.2 and the device is a TZ210 with it's LAN network being 192.168.1.0 /24
The co-los gateway is 204.244.50.254 and the device is an ASR 2911 with it's LAN network being 10.0.10.0 /24
The S2S VPN connection is up between the two locations and the 2911 device and the servers within it's LAN can ping and RDP to the office's machines. The office network can only ping the LAN interface IP on the 2911 which is 10.0.10.1 but not the servers in the network. the site-to-site VPN was set up with the CCP wizard.
How can I allow the 192.168.1.0/24 network to see the 10.0.10.1/24 network and why do I only currently see the gateway?
If need be I can post my running-config file with the preshare keys redacted.
I have lots of 857's routers in the field with mostly the latest OS - 12.4(15)T17 making ezVPN connections to a 2951 with 15.1(4)M5.All the 857's have lookback and vlan interfaces similar to :
interface Loopback0
ip address 50.43.8.1 255.255.255.255
ip tcp adjust-mss 1452
end
[code]....
Now lately for some or other reason we have instances where I can ping either the VLAN or the LOOPBACK interface, but not both. Or I have instances where the 2951 can ping all the interfaces on the 857, but the 857 can not ping the 2951. Or I have instances where the 2951 can not ping the 857, but the 857 can ping the 2951.The way I have been fixing this is either to add crypto ipsec client ezvpn SMS_VPN inside to the loopback interface, or if it is there already to remove it. This usually works for a few days, but then suddenly I have to reverse this again. If that does not work then I usually do lots of clear crypt sess and/or clear crypt ipsec client ezvpn on the 857, or clear crypt sess remote 857_ip_address from the 2951 and then suddenly it starts working again.
Laptop is dell,running on windows 7 home basic and desktop is running on windows xp professional.how to configure both computer network to share huge files between them..
View 7 Replies View Relatedhow do i get a mac g3(old) to see my windows 7 system. my windows 7 can see my mac but ican not get the mac laptop to see the win 7 desktop. i need to be able to get the mac to use the win dvd drive to load mac osx(no cd/dvd drive in the mac).running mac os9.2 on mac currently, would like to upgrade, i have the mac osx disk.
View 1 Replies View RelatedI have a simple home lan setup. Desktop(Windows 7 Ultimate) wired to router and laptop(Win Home BAsic) using WiFi. Both have All Printer and file sharing Enabledhe desktop cann see the Laptop in 'Network' but not the other way around. However, even though I cannot see the Desktop from the Laptop's 'Network' I can access the public folder of the desktop by using : \desktop-pcuserspublic command in cmd or search.Now why Is the Desktop not visible on the Laptop's network(though I can access it) and why can't the Desktop access the Laptop's shared public folder even though it can see it in his network?
View 3 Replies View RelatedI think that's what I want to do. I have an HP desktop with vista and cable high speed modem and a linkys attached to it for wireless. My laptop is a toshiba with wireless running windows 7 and I use it upstairs wireless to connect to the net. There are times I need a file from the desktop and I have to go down and put it on memory stick to copy it over. Is there any way I can access the desktop from the laptop without having to do that? Would need step by step instructions to set it up if it can be done with 2 different operating systems.
View 11 Replies View RelatedI have a desktop and a laptop. Both use Windows XP. The laptop has wireless access to the internet. The desktop is wired to the Internet. How do I use the laptop to access files on the desktop.
View 1 Replies View RelatedWork with VNC to a remote computer. It has an old monitor with 800x600 resolution. Laptop that worker has higher resolution. How do I set a higher resolution monitor remote computer without buying one.
View 1 Replies View RelatedI have a laser printer that's connected to a desktop running Win 7. The printer is set to SHARE. I got a laptop that I want to print from through the desktop. Is this possible? The printer is not wireless and I don't have a print server. I have wireless network running on my Linksys router, but the desktop and the printer are not on it.I have the desktop and laptop on the same WORKGROUP, but when I try to add the printer on the laptop by selecting a NETWORKED PRINTER option, I get an error.
View 2 Replies View Relatedhow i get net to desktop by connecting to laptop.
View 1 Replies View Relatedi have laptop and desktop both and i want to connect to transfer files and share
View 4 Replies View RelatedMy desktop is connected to the same wireless network as my laptop yet my laptop has connection while my desktop does not.The desktop might actually be connected directly do a router (says 'local area connection 2 connected' right now but still no connection).I checked other posts on other websites that say to post all this command-prompt information that i cant necessarily access because i do not know the administrator password.
View 9 Replies View Relatedneed to connect my friend's labtop to my desktop computer
View 1 Replies View RelatedUsing packet tracer I get an error saying:
Config
nat(inside) 1.0.0.0.0.0.0.0.0
match ip inside andy inside any
dynamic translaion to pool 1 (matching global)
translate_hits=45236,untranslate_hits=0
I cannot access my polycom unit on 172.20.16.8 via 10.20.60.8 below is my results of show run Result of the command: "show run"
: Saved
:
ASA Version 8.2(2)
!
hostname ciscoasa-stt
domain-name stt.vidol.gov
enable password qXcSIHaSa9B75GQC encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code]....
I currently have my ISP-supplied modem wired to both my router and an old, old desktop. Can I run this network without using a desktop ethernet connection & throw away the desktop?
View 3 Replies View Related