I need to upgrade the fwsm image from 3.1(10) to 4.0(8). Can i do it directly from 3.1(10) to 4.0(8) ?Do i need to upgrade other image also along with Firewall version 4.0(8)?
[code]....
I want to upgrade a pair of FWSM in active failover from 4.0(4) to 4.1(8) i just want to double check the process. i have tftp access to the primary at the minute. i cannot access the same tftp server with the standby. do i need flip over to the standby to be able to tftp the image across?
failover activehostname# changeto system
hostname# copy tftp://x.x.x.x/c6svc-fwm-k9.4-1-8.bin flash:image
hostname# copy tftp://x.x.x.x/asdm-622f.bin flash:asdm
hostname# reload
Once i have the images loaded i reload both at the same time?[URL]
I am planning for an VSS in Core but firstly I need to upgrade FWSM which is at 3.2 Ver to 4.0.4 (min release) I have checked software dependencies but not sure about Hardware Dependency on Fwsm and Chassis for Eg. Rommon Upgrade on Chassis.
View 7 Replies View RelatedWe would like to decommission our FWSMs and upgrade to the ASA 5555Xs. This leads me to ask the following: What would be the most efficient way of doing this without any interruption to production? How to successfully accomplish this?
View 1 Replies View RelatedCan I upgrade FWSM 4.0.3 to 4.0.17 with Chassis IOS s72033-adventerprisek9_wan-mz.122-33.SXH4.bin ?
In chassis's slot we have ACE and FWSM slot also. if I will upgrade chassis it will reboot ACE too.I do not want to reload Chassis.
I have few questions on FWSM software upgrade.
1) I could not find the availale maintenance software under software donwload section?
2) what is the maintenance software version required for fwsm 4.1.8 upgrade (this does not have on the release note) url...
3) what is the main difference when you upgrad fwsm using following two methods:
- Installing to the current application partition from the FWSM CLI
- Installing to any application partition from the maintenance partition
4) how can we verify the file integrity after copied from tftp/ftp server (because it does not support verify command as in IOS)
5) how can we see the copied files in the fwsm (it does not show with show flash or dir commands)
I'm looking at upgrading our FWSM modules in our 6500's. They're the WS-SVC-FWM-1 modules.
We're running on version 3.2(12) at the moment and I'm looking to jump up to 4. Any recommendations around whether I should to go to 4.1(6) or 4.0(16)? There aren't any features in particular that I would need in 4.1 but want a good stable base to sit on for 12 months until I look at this exercise all over again.
I got a PIX 501 off ebay and im trying to upgrade it to have an ASDM image on it.Ive downloaded every copy of the ASDM image i can get my hands on, and when i transfer it to the PIX when its up and running i get out of memory, If i do it through monitor mode, i get the error "bad magic number" no matter what i transfer to itI can transfer a new image to the PIX (a non asdm one through monitor mode.
View 3 Replies View RelatedWe are now using image 8.0(4) for my ASA 5510. Later on, I would like to upgrade the image to 8.4(3).May I have to know what difference for those images, what should I take care of the script?
View 1 Replies View RelatedI'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies View RelatedWe are planning to upgrade the IOS on our two 6509E supervisors in the next few weeks. We currently run IOS 12.2(33) SXI1 and are upgrading to 12.2(33) SXJ3. At the moment the two supervisors are in SSO mode and after reading many articles it says that when the images are different on the two supervisors they are in RPR mode. When you then reload the active supervisor it will reboot all the line cards.
1. Is above correct? Will my line card reload?
2. We also have a FWSM installed, When/If the line cards are rebooted does the FWSM also reboot?
i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
i have cisco 1260 Access point with standalone ios ap3g1-k9w7-tar.124-23c. i download new IOS to connect the AP to the controller the new ios is ap3g1-k9w8-tar.124-23c.JA5.tar. upgrade th AP to LAP. is it just install ios like in router & switch by tftp?
View 1 Replies View RelatedI have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies View RelatedI upgrade the IOS for switch c2960 and the switch do not boot from the new image.See the files attached.
show version
show boot
show flash
There is a mistake with settings?
I am going to upgrade the IOS image on 6509-E SUP 2T from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.
View 4 Replies View RelatedI wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.
View 1 Replies View RelatedI have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies View RelatedI own the Cisco switch,2950-24.When power on,it says Crash fault with information showed below: [code] Then I search google.com and found the resolution of upgrating IOS.I push mode button before power.Then I access into the CLI.I checked the files in the flash: and got these. [code]
View 8 Replies View RelatedI upgraded my WISM software to v. 7.0.116.0. The upgrade went smoothly. Most of my WAPs are H-REAP and they are working fine. I have a few local mode WAPs that are stuck in a downloading state. They will try to download, reboot, then try to download again. This is happening only with the WAPs in local mode. These WAPs were working before the upgrade.
View 2 Replies View RelatedI am trying to upgrade my cisco WS 2960 24 TC-L switch with the IOS image c2960-lanbasek9-mz.122-55.SE6.bin and my existing IOS image is c2960-lanbasek9-mz.122-50.SE5.bin. when i am copying it to flash, it is getting copied but when i tried to boot it after entering command boot system c2960-lanbasek9-mz.122-55.SE6.bin , it gave me an error.
both flash dir and error are attahced herewith.
I have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is 7.0.116.0 (default) 7.0.98.218 (active) so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its 7.0.116.0 (default)(active) 7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting.
I am planning to upgrade BootLoader image of 7206VXR router due to booting issue. The router is not booting .But if I go to rommon and give boot it will boot.So I am upgarding my Boot Loader image. Now the Bootloader image and IOS image are exactly same.Can I upgarde the Bootloader image to latest version without upgarding IOS?
View 3 Replies View RelatedHow can I Upgrade a Cisco 3750X 12-SFP switch with IP Base to IP Services Image?
View 1 Replies View RelatedI have a 10nos of cisco 2960 switches and 1no of cisco 3725 gigabit switch. all 2960 switches are parallaly connected to 3725 switch though fiber.
all the switches are having same vlan and public ips for management.
Now I want to upgrade IOS for all 2960 switches at a time, how to up grade IOS same time for all switches.
Is there any docs with step by steps on upgrading the IOS software image on 4507R+E with dual sup6L-E ?
View 3 Replies View RelatedI want to upgrade my DRAM of 256MB to 512MB to support 15.1 IOS image.Can I buy Cisco approved DRAM from third party Like [URL]
View 1 Replies View RelatedWe have 2 FWSM modules in each 6500 switches. 1st module is having 04 firewall vlan groups with 18 vlan interfaces in a single context firewall. All are working fine with no issues. Recently we create one more vlan on MFSC and add into the same firewall module. However newly created vlan inside the FW is not able to communicate with outside and also outside users not able to reach newly created subnet. But within the firewall zones (other interfaces) it can communicate. Once we did packet capture we noticed that its hitting firewall outside interface only and when we ping we got TTL expired error. we have default routes to outside and there's no any route inside as new segment is within the firewall (no any hop).
I guess there's no limitation on number of vlans that we can assign on one firewall eventhough there is a limitation for number of vlan-group which is 16 max (but we are within that limit).
Can any1 tell me wat is the difference between ASA-SM1 and FWSM.
View 2 Replies View RelatedI wanna upgrade FWSM Version 3.1(11) to latest 4.x version is this possible or i have to upgrade first to 3.2 and then to 4.x?
Is there any changes in configuration commands that i need to know? The version that 6500 running is s72033-advipservicesk9_wan-mz.122-18.SXF14.bin,an upgrade to 6500 is needed also?And if so what ios version will i put?Also which is the asdm supported version?
We recently deployed a FWSM on our 6503-e boxes (w/ sup720). NAT is working (PAT) but the issue I am seeing is private traffic from remote sites is not being allowed through the FW. I was able to get the remote site to ping the FWSM itself (inside address), but no hosts behind it. Maybe an ACL issue? Also when I turn off NAT on the remote end, I can than access everything (We are NATng on both ends). Im a routing guy by nature so I will defer this to the security guys out there.
Topology
Hosts (inside/10.15.25.0/24) > FWSM (outside/public IP) -> Core Router -> MPLS CLOUD -> Core Router (NATng) - > Hosts (192.168.1.0/24)
ACLs applied to inside/outside interface
FWSM# show access-list ATX-ALLOW-IN
access-list ATX-ALLOW-IN; 15 elements
access-list ATX-ALLOW-IN extended permit tcp any any (hitcnt=222)
[Code]....
We have a pair of 6500s with Sup720 running 12.2(33)SXI3. Each has an ACE-20 (s/w A2(2.0)) and FWSM (s/w v3.2(15)). We have reached a limit on the number of rules we can configure on the FWSM, and have determined that we shall upgrade to 4.1(5), with ASDM to 6.2(2)F. A question has been raised regarding the s/w on the ACE-20 modules. Do we need to upgrade them as well?
View 2 Replies View RelatedASA code 8.3 and higher uses NAT objects and totally changes the NAT rule config. I am new to FWSM .... but was wondering if this comparable ? I am lookinig at upgrading FWSM 3.1(16) to a higher 4.1 version .... but have a feeling this could be a huge task if NAT config changes as with the ASA's
View 2 Replies View Related
