Belkin Routers :: N600 Gives 2 Slow Green Flashes And Then Nothing Happens
Nov 18, 2012
I was having problems setting up dd-wrt so I wanted to flash back to the Belkin firmware and try again. I went to what I thought was the product page for the N600 and found the latest version of the firmware and flashed to it. The only thing it does now when I plug it in is 2 slow flashes of the green light and then nothing. I tried holding down the WPS button while plugging it in and I get the light to stay green but it doesn't respond to 192.168.2.1.\
View 6 Replies
ADVERTISEMENT
Feb 12, 2013
I can not fix the problem with the router. I power it up, all is GREEN, then it blinks RED, then GREEN, and finally RED. The router is terminally not connected to the Internet. How can I check if the router is BAD. I have done all the troubleshooting, examples:
connected ethernet directly to computer - no problems
attempted to fix problems via belkin software
changed channels on modem
updated firmware
etc, etc
View 1 Replies
View Related
Feb 13, 2013
Having an issue with my Belkin N600 router - when initially installed it was working fine but in the past week it has gtten slower - if I connect directly to my DSL modem my speed is 1.5 MBS when I use the router connection my speed drops to .1 MBS - tried resetting to factory defaults & that did not work also tried resetting my modem *& router still having the same issue.
View 9 Replies
View Related
Oct 19, 2012
Accessing my hdd on the usbport is very slow. Have a n600 router. Can I boost this in any way?
View 2 Replies
View Related
Aug 11, 2011
I have 3 1142N AP's. I plugged them in one at a time here at my desk and they work fine. When I take them upstairs and install them only one of them works. I can move the working one to the other locations and it still works. The LED flashes continously green on the other two.
View 4 Replies
View Related
Mar 4, 2013
I have two LAP1041 with WLC2504 everything works fine. But since yesterday when it boots up it flashes green, then solid green, then after about 10 seconds the green LED turns off, however the LAP is still working fine, Why is that? If I put my eyeball up close to the LED I see dim red inside the LED plastic cover.
View 3 Replies
View Related
Dec 12, 2012
Belkin F5D8236-4 v1 The Internet flashes amber and goes back to solid blue. It will stay blue on average for up to five minutes (this is not exact times) but on average it happens every five minutes. This is a constant issue. I've contacted my ISP (Comcast) and they said all looks fine on their end. My signals to them are just fine.
Sure, I can bypass the router all together, but my modem will NOT allow me to see any logs to know the issue is happening on their end. I'm feeling a bit confident its a router issue though.
I've reset both Modem and Router. I've made sure my connection was set to Dynamic. My router/security log does not offer up anything at the times this happens, but I do see several listings for "sending OFFER to a local IP of one of our laptops, but this does not match the times the router net light goes amber.
Yes, when the amber light is flashing on the globe/internet icon, I can still access my router page, but it does say DISCONNECTED. It will eventually go back to connected in a few minutes. This router is not very old and I've always praised Belkin routers, so crossing fingers my router is okay, times are tough for so many of us.
View 9 Replies
View Related
May 22, 2013
Belkin n wireless router model number F5D8236 v1! my modem is showing an internet connection but my router "modem" light is flashing orange and my internet light doesn't even come on. we are not sure but we believe this became a problem last night after my daughter connected her new lap top to the wireless connection.
View 1 Replies
View Related
Sep 1, 2011
I have a Belkin N600 HD.I'm on an Off-net ADSL2 Connection with TPG.It took 2 weeks to connect.I've connected and I'm still downloading at 1.5Mbps (150kb/s)I bought new Lie filters/splitter in case the same ones I have were faulty (C1024M) and connected them correct to both my home phone and my Modem.So I've connected to my net, I can download and do whatever but I'm going at my ADSL1 Speeds. My friend is on the same connection, same modem (he bought it cause of me) and he's hitting higher then me (500kb/s, 600kb/s) Although he's on a separate line so no filters required (I think).He lives about 5minutes away from me (car) and is about the same distance from the exchange as I am (2.5km give or take) [code]
View 1 Replies
View Related
Jan 14, 2013
i have an internet but my f7d6301 v1 not working ...the device flush red color instead of green
View 1 Replies
View Related
Dec 12, 2012
N600 router will not comunicate with my desktop computer through a cisco switch. The LAN was working fine when I was using a Linksys router. Is this a compatability problem between Belkin and Linksys products?
View 1 Replies
View Related
Mar 4, 2013
Where can I get the setup software for my N600DB USB adapter, I cannot find the CD I got with my wireless adapter.
View 1 Replies
View Related
Feb 13, 2013
I have a N600dp. My printer, Brother MFC-J410W, is plugged into the router USB port. The printer function works but the scanner function doesn't. I keep getting an error message that the printer is not connected.
View 1 Replies
View Related
Mar 27, 2013
Will the N600 Belkin router is DD-WRT compatible, because I saw in a database it is not. Is there also a way to make it DD-WRT compatible, e.g. flashing it ? Do you have a download on the router support side.
View 2 Replies
View Related
Feb 9, 2013
One of the laptops in my home connects to the wireless network provided by my brand new Belkin (N600 Dual Band) router with no difficulty at all - the other will not connect at all (it SAYS it is connected to the network, but it says that it is a 'Local Connection Only, and will not open any web browsers or allow you to get on to the internet) why is this happening and, more importantly.
View 1 Replies
View Related
Dec 30, 2012
trying to add a media storage device (3 TB WD My Book Essentials) to my N600 DB router via USB. I have partitioned the HD 2 TB / 1 TB. I have tried several formatting scheme but the router is still not recognizing the HD. Have refreshed, reset, and done a firmware upgrade to the 600.
View 2 Replies
View Related
Jun 10, 2013
I set up an external hard drive to my router. I don't know how to see those files on other devices.
View 2 Replies
View Related
Jun 7, 2013
Upstairs I have a Century Link modem/wireless router. My wife and I use our laptops, smart phones, and XBox 360 on the wireless network. Downstairs I have an older Dell PC that I use for my business. I have an Ethernet run from upstairs to downstairs. The Ethernet jack upstairs is near a cable outlet because we used to have cable internet. Now we have DSL and the phone jack is on the other side of the room. Here's my question... I have a Belkin N600 wireless router, is there any way I can plug it into the Ethernet port on the other side of the room, and use it like a wireless adapter? I have tried a few time to set it up as an "access point" but it doesn't seem to work. As soon as I do, I can no longer access the Belkin router to make any changes and I need to do a manual reset. can I plug my downstairs PC into the Belkin N600, and have wi-fi internet access from the wireless modem/router upstairs?
View 2 Replies
View Related
Mar 4, 2013
I have a Canon i6700d, which I connect to the belkin N600 USB port to share on the network. Driver for the printer is installed. From the belkin router monitor, the printer is listed under "Networked USB devices". However, the printer is grayed out and can not be selected. the dialog complains that the printer is not available.
View 1 Replies
View Related
Nov 8, 2012
Are Belkin routers compatible with VPN? Is there a VPN pass through setting for the N600?
View 3 Replies
View Related
Jan 13, 2009
I have a N600dp. My printer, Brother MFC-J410W, is plugged into the router USB port. The printer function works but the scanner function doesn't. I keep getting an error message that the printer is not connected.
View 5 Replies
View Related
Mar 30, 2013
how do I rename my ssid on belkin n600 db. it did not come with a cd rom and all the online manuals do not discuss it.
View 1 Replies
View Related
Apr 20, 2013
I have a wi fi capable blu ray player which works on wireless g connections, and I also have 2 computers. I have the N600 Dual Band router, and want to know if it is possible to transmit on both frequencies? I am only seeing the 2.4ghz show up for a connection.
View 1 Replies
View Related
Oct 27, 2012
Tried to install a n600 DB on a windows 8 computer. Got the message "Not compatible. When will it be?
View 1 Replies
View Related
Mar 1, 2013
I'm a bit confused about Belkin's firmware upgrading. I lookup the firmware for my router N600 (F9K1102v1) and see that I've got options for v1, v2, and v3. Is it possible to upgrade my router to the v3 firmware? I'm guessing that I can't because its a v1 router, but just thought I'd ask just in case I can. Don't want to brick the thing.
View 2 Replies
View Related
Jan 19, 2013
The Belkin N600 DB N+ Router. It has 2 seperate networks for optimum performance, how do i go about choosing which band I want to use? Under the Belkin desktop I can clearly see 2 SSID's. One shows 2.4 GHz SSID & network name and the other 5GHz SSID & network name. media. But when I pull up my wireless connections I only see 1 network.
View 1 Replies
View Related
Mar 12, 2013
Can't download newest firmware for F9K1102/N600 DB Router. I am on 1.00.19 and there are two newer firmwares, the latest being 3.03.12. This firmware is suppose to allow support for Windows 8. All my computers now have Windows 8 so I want this firmware, but I can't download it because the link provided by belkin no longer exists
View 3 Replies
View Related
Dec 29, 2012
I have a N600 router. Yesterday, for the first time, I was unable to connect to the internet from my TV. It keeps saying network connection failed. I have unplugged the router and modem several times and that does not work. When I check the various wireless systems available (on the TV screen) I see mine there but it will not connect. At one point I did see something that said ethernet cable disconnected, but I checked and the cable is connected.
View 4 Replies
View Related
Dec 21, 2012
Just installed N600 router. Works for my Windows 7 PC and my Android phone. Does not work with my Windows VISTA PC. It connects to the Router ok, but does not connect with the Internet. Also says UNIDENTIFIED NETWORK. What am I missing?
View 1 Replies
View Related
Nov 1, 2012
I'm trying to check what quantity of data is going through the router. I can see there is a monitor that tells you in real time the output for the last few minutes, but I want to keep track of monthly usage so I know whether I'm nearing my download limit set by my ISP. Is this possible with the Play N600??
View 1 Replies
View Related
Dec 5, 2012
I have a Belkin N600 DB and i want to know how to stop the spinning of my HD plug in the USB plug ,when the hard drive is not used.
View 1 Replies
View Related
Nov 1, 2012
A N600 Router Model F9J1102v1 router first installed in July 2012 with WPA-PSK, MAC Address Filtering and "Self Healing" enabled would not allow a new PC to connect via an RJ45 port. Belkin support ask for the unit to be reset to factory settings which is done and the Security system re-enabled again. Valid MAC Addresses start to be added and midway a PC is discovered in the Network without its MAC address added. Closer scrutiny reveals that another unknown device has also found a way into the router and that the 'Block' option on the MAC list is also failing to work. Anyone think of what one should do with this security shambles other than turn the thing off quick?
View 7 Replies
View Related
Dec 5, 2012
I was having problems connecting to one of my usb devices that was plugged into my router. I unplugged the router to reset it and whenever it starts up it flashes green and the green light goes solid for less then a minute before turning red. It's a solid red light. I've tried unplugging everything and restarting it and nothing. Ironically it still lets me connect to the internet but when I access the control panel on my computer it shows as disconnected. Is this means my router is busted. This is my second Belkin Router and the only reason I had to replace the last one is because it was a G+Mimi router and I upgraded to an N Router.
View 3 Replies
View Related
