Centrino N6150 And Netgear WNDR3700 Slow To Validate?
Oct 21, 2012
I have numerous phones and laptops that connect to the router just fine and fastThis ASUS laptop (windows 7) with Centrino N6150 is very slow to validate. At least it appears that's the issue. The icon in the tray starts with a ! in the connection, then in about 45 seconds goes to a blue chase circle, then in about 45 seconds connects.istory. I was getting disconnects from the WIFI router on a continual basis. I decided to put the router back to factory settings, did the pin reset etc, did a full setup and now we have this slow connect issue ALTHOUGH I never get a disconnect if I once get connected. Just seems to take forever to get it to connect.I've looked at conflicting IP's, no avail, seems fine. As mentioned, like the iphones connect almost instantly. The HP laptop connects fast (windows 7) but the asus now isn't happy.
View 19 Replies
ADVERTISEMENT
Jul 12, 2011
i set-up the D-LINK DNS 323 NAS unit with RAID 1 (dual 2-terabyte 5400 rpm drives)
it works, but it is slow in copying files between my computer and it (8 minutes to copy 7.94 gig file between NAS and my PC via wire).
i am using netgear WNDR3700 gigabit router. replaced the network wires to the latest spec, and my computer has realtek PCIe GBE network adapter.
this is looking more and more like the NAS RAID 1 is the bottleneck.. possibly 7200 RPM drives would have kicked more ass?
View 2 Replies
View Related
Apr 7, 2011
I cannot access the setup page, even without the modem connected to the router, even after pushing reset button. It says I have limited access both to the wireless and to the wired connections, but won't let me access the internet (via the separate modem)I can access the internet via the modem fine
View 2 Replies
View Related
Jul 27, 2011
I'm in a bit of a predicament. Trying to set up a Netgear WNDR3700 behind a SonicWall TZ170 SP (Standard OS). The only thing I really want the SonicWall to do is maintain site-to-site VPN connections to a few other networks that I work with.
The SonicWall WAN is passing Internet connectivity to the LAN ports as it is supposed to but the hangup seems to happen at the Netgear; it doesn't seem to want to receive Internet connectivity from anything but a modem and it doesn't want it going to any port but the Internet port (IE, it doesn't seem to want to share Internet via the switches).
I'm thinking this may be a limitation of the firmware and that dd-wrt might be the only answer but I thought I'd bring it here first as my last experience with dd-wrt wasn't a good one.
View 7 Replies
View Related
Jan 21, 2012
I am trying to forward the ports for several ip network cams, that have built in webservers, on this router. I have done this before on my old Linksys router with no problems but the Netgear has me stumped.The only way I can reach any of these devices from the Internet is to map them to port 80. But that limits me to one device, hence the need to forward more ports.All cams have fixed ip addresses so it is not an issue of their ip addresses changing.
View 19 Replies
View Related
Mar 3, 2012
My old router (a dlink dir-615) works just fine, but I figured I would upgrade and try to run OpenWRT or DD-WRT so that I could have one VPN for all my devices.
Anyway, I took the router out and followed the instructions (power off modem for at least 1 minute, connect modem to router, router to computer via ethernet, turn on modem first, wait for it to fully boot up, turn on router, wait for it to fully boot up, and then run the setup on routerlogin.net. The router is currently setup and I can connect my computer or iphone to it just fine, but I cannot access the internet. It doesn't make a difference whether I'm connected via ethernet or wifi. Either way, I get a "No Internet Access" message from Windows 7.
I've tried turning everything off and starting again. No luck. When I go back to my dlink router, everything works fine again.
So, in short:
Modem + ethernet = internet
Modem + Netgear router + ethernet = no internet
Modem + Netgear router + wifi = no internet
Modem + Dlink router (wifi...haven't tried ethernet) = internet
View 8 Replies
View Related
Mar 26, 2011
URL ,A Netgear WNDR3700 for only $80? Everywhere else I have looked they've been over $100.
View 2 Replies
View Related
Apr 28, 2011
Dell 8600 centrino intel pro wireless lan 2100 won't connect to netgear n150 wnr1000. Running 802.11b band it sees wireless network but won't connect. I have 2 other computers connected to network so it works.... I don't know if Netgear n150 is compatible with 802.11b band...
View 1 Replies
View Related
Sep 12, 2011
I have just got my new xps 17 and opted for the 6230, It only gets to 20 meg download speed, I can insert my old usb N adaptor and get the full 50 meg. I was on the phone for 2 hours last night with Dell, they had remote access and tried lots of things to improve the problem.
Finally once they saw that my old usb adaptor was much faster, they said a technician would call me back today betweek 12pm and 1pm or 4.30pm.
View 11 Replies
View Related
Feb 16, 2011
I can connect to my LAN, but with local access only. I've been to the mfg's forums and tried their fixes, driver updates, and manual setups- no joy so I've reset to auto defaults. This laptop connects to several other routers wi-fi without problems. The WNDR3700 solved all my previous router problems, was truly plug and play, and may have cured me athsma as well. The event logs show a time-out during the semaphore portion of the log-in.
View 12 Replies
View Related
Jun 4, 2012
I puchased the N600 WNDR3700v3 Dual Band Gigabit Router. I am able to see my wireless account I set up and is out there to connect to, but I cant connect. I can connect with an ethernet cord, but nothing wireless. It doesnt work for my home or work laptops. Prior to this I had another wireless set up and I am tempted to plug that one back in.
View 1 Replies
View Related
Jun 2, 2011
I have been unable to access my WHS when I recently traveled across the US. I have a Netgear WNDR3700 router. My DSL modem is a DSL-520B. I have AT&T DSL (6 Mbs). I have tried enabling and disabling "remote management", forwarding to ports 80, 443, 3390, and 4125 all with no success.Also, I believe (correct me if I am wrong) the remote management address is incorrectly listed as http://192.168.1.2:8080. I have also turned off USB storage in case of a possible conflict I have read about with port 80.
View 4 Replies
View Related
Jan 19, 2012
Just got my router running and when I connected to it via my laptop, it didn't ask for a password and it says unsecured connection when I put my mouse over it. Where do I go in the settings? I do not see it at all?
View 3 Replies
View Related
Jun 22, 2012
I have had a Netgear WNDR3700 wireless router for over a year now, and have had no problems connecting to wireless devices (currently connects perfectly to: windows 7, OSX, Android, and Meego). I have recently purchased a Sony Bravia NX720, which has a built in wireless card. When I connect the television via LAN to the router the internet works fine, however when I connect via my wifi network (i.e. there is no physical connection between the tv and the router) I get the following message:
Connection Results
Wireless Device On TV: found
Local Access: OK
[Code].....
View 7 Replies
View Related
Feb 26, 2011
I cannot connect through my wireless router (Netgear WNDR3700) WITH MY INSPIRION DUO. I can connect with a verizon MYFI wireless card, and alo through ethernet on Duo. I get "Problem with wireless adapter or access point" The software driver is newest. System ism W7 Home premium
View 1 Replies
View Related
Mar 21, 2013
I have two computers(with problems over 15 that work fine) an All in one Sony that has a qualcom 9285 and a new l521x dell laptop with a dell 1901 (also atheros).I have these issues with the sony for a few years - and just wrote it off as a computer problem - we have had the sony tech come out and replace the entire motherboard, wifi module?what made me link the issue with Atheros and the router was that my new laptop is behaving the same way as the sony. They both show connected to interenet (windows 7 64 bit(sony) and windows 8(dell)) I get an IP address, and I can ping websites. If I click to watch the network traffic (on the local connection status activity) I can see 50,000 bytes received every second I have updated the sonys and dells drivers to the latest one both from sony/dells site and from atheros download site as well - but it doesn't seem to make any difference The router also states its fully up to date
Hardware VersionWNDR3700
Firmware VersionV1.0.7.98NA
GUI Language VersionV1.0.0.64
View 5 Replies
View Related
Oct 26, 2011
I use both Gigabit LAN and "N" class WIFI through my WNDR3700 to connect to my Network. Can I use a Verizon MIFI4510L to connect to the Internet?
View 1 Replies
View Related
Sep 10, 2011
I have a Netgear WNDR3700 v2 that I loaded with dd-wrt (v24-sp2 std). The only real problem that I am having is with the wireless. I can't get anything to connect at 300mbps. Even if I set it to n only it still only connects at 54mbps. Right now I am running it with encrytion off to rule out that causing any problems. and yes it would connect at 300mbps with the stock netgear firmware.
View 3 Replies
View Related
Jan 11, 2012
I've been replacing my Netgear WNDR3700 (currently only serving as wired router and gigabit switch) with an Untangle box.Obviously, only the free "Lite" version would be worth it, as the others are priced ridiculously for non business use. I've had a hard time figuring out from their webpage how the features of the "Lite" compare to the others, particularly how Spam Blocker Lite, Web Filter Lite and Virus Blocker Lite compare to the full versions of each.
Is the untangle router any good? How do its management features compare with consumer solutions?The new web caching feature seems really cool too, especially when multiple systems grab the same large updates or download the same steam games, but at $54/year it seems a bit excessively priced for home use, so I'd probably just be sticking with the base free version.
View 19 Replies
View Related
Oct 31, 2012
I have Comcast cable and prior to a couple days ago, it has always been smooth @ 36mbps download and 5mbps upload. I have a Netgear WNDR3700 and Motorola 6121 connected to my PC via Ethernet cable. Up until a couple days ago, I've been getting lag spikes where my games would completely freeze for a good 2-3 seconds and resume, as if the entire connection dropped and reconnected. I did a speedtest and I was getting around 4mbps download and 1-2mbps upload with huge fluctuation in speed.
I called Comcast and they said they were seeing a "red" signal error from their end so they sent out a tech to my house. He came over, changed some cables outside because they were corroded and that's about all he did. I tested my connection while he was still there and I was again getting 36mbps download and 5mbps upload. It was a quick 1-2 test so everything seemed normal until I started to see lag in games again.
I am getting the same lag spikes, albeit it's not as bad as before but it's still pretty annoying. Using speedtests, I am still getting 36mbps download but the graphs show that there are inconsistencies where there would be sudden drops in speed and picks back up still to show 36mbps. These drops are what I assume are the lag spikes. The upload is also suffering now, dropping down to 2-3mbps and it takes the test about 20-30seconds to load the upload portion of the test. Even loading web pages, sometimes it locks up for a few seconds longer than it should, which is normally instantaneous.
I have tried connecting my PC directly to the modem to bypass the router and am still getting the same lag, probably a little LESS but still the lag is there. My router is has always been updated to the latest firmware.
View 4 Replies
View Related
Jul 2, 2011
I'm going to be moving into a place in the next couple months where I'll have to go wireless on my desktop (until now I've just done Ethernet so I don't even have a wifi card on my desktop). The router/modem aren't anywhere near my bedroom so my gear will be going wireless from now on All my devices are built-in wifi ready but not my desktop.
I would like recommendations as to a rock-solid, reliable, fast and well performing card as I can to make up for no hardwired connection. Especially with BF3 coming out I'm not all that thrilled with being forced into this situation but you gotta do what you gotta do. Anyhow, I'll be bringing my router (Netgear WNDR3700) so I'll have the range and speed from there about as good as I can get, so I'd like a card of equal merit.
One side note...probably not really feasible considering I want speed and performance as a priority, but I would love a card (if possible) without bullshit antennas sticking out of the case, or with external antennas you have to set up on your desk. I will go that route if I have to but man that is an aesthetic nightmare, IMO. The ones that stick out of the back of the case are the worst looking for me just as a caveat.
View 1 Replies
View Related
Aug 29, 2011
I just ran Cat6 from my WNDR3700 to a netgear NeoTV550. WNDR is in the computer room and the Neo is in the living room. Cat6 had to be fished downstairs, around the bathroom wall and over the solid plaster ceiling. Fun times! My question is, should I add a switch to the connection on the far end, essentially creating a trunk sans dot1.q tagging and then plug the Neo in? Or should I just plug directly into the Neo?
View 3 Replies
View Related
Jul 7, 2011
I have basically the following setup: It's a home network, running with a Netgear WNDR3700 wireless router.
Wireless Devices on the Network:
Google Nexus One: 802.11 b/g/n
iPhone (Original): 802.11 b/g
Main Workstation Laptop: 802.11 a/b/g
"Beater/Other" Laptop: 802.11g b/g
Ethernetted devices on the network:
Logitech Revue: CAT-5e
I'm running both the 2.4 GHz and the 5.0 GHz networks over the same SSID. The goal, obviously, is to get everything over to N if possible. I've heard that wireless N has much better signal and transfer rates, is this true? Also, is running the two different frequencies with the same SSID problematic? It's kind of strange, because my Nexus One is having a difficult time staying connected to the network in my office while the main workstation laptop in the same room is getting a much better signal.
[Code]....
What's interesting is that both are running on the 2.4 GHz networks, essentially both not on the wireless n network, which kind of defeats the whole purpose of things. Is it bad to run both the 2.4 and 5.0 GHz networks with the same SSID? If using a network repeater, is it bad to rebroadcast the original network with the same SSID as the source network? It seems that the 5.0 GHz network is getting "clobbered" by the 2.4 GHz network. Is it really necessary for me to broadcast using different SSIDs?
View 1 Replies
View Related
Dec 31, 2012
I'm having problems connecting to the Internet using the wireless adaptor - it will connect initially but the connection is very very slow and then will eventually drop out and stop working.When I connect using an Ethernet cable, there are no problems whatsoever so I know it is not a service provider issue.I have updated the BIOS to A11 and all drivers are up to date. The wireless adaptor is Intel Centrino Wireless-N 1030. [code]
View 3 Replies
View Related
Jan 29, 2010
I am trying to configure a 3300 Wireless Print Adapter with a NET GEAR WNDR3700 Wireless N Router. During the Configuration if I have no security set up on my network, the 3300 establishes a connection. If I however, turn any form of security on ( WEP, WPA-PSK [TKIP, WPA-PSK [TKIP] + WPA2-PSK [AES] ), the Connection fails. No security is not an option.
This happened while switching routers. The 3300 worked fine on my D-Link Wireless G router (WEP). I was wondering how to resolve it.?
View 7 Replies
View Related
Feb 12, 2012
I received a message stating: Info-error attempting to validate the winsock base providers:2 Error- Not all base service provider entries could be found in winsock catalog. A reset is needed. Info- Redirecting user to support call I did the reset in command prompt as I read you told other people with this problem to do. But I still keep getting these messages.This is my sister's Dell Latitude 620.I used AVG and I think pc is clean. When I try to connect to a website page states that Internet Explorer cannot display the webpage.
View 10 Replies
View Related
Jul 28, 2011
I have been hacking at this problem for two days and can not figure it out.I built a new computer ASUS M3A78-T and installed windows 7 64bit everything was working fine. I did not validate the version of windows because I was waiting to replace the 500g hard drive with a 120 ssd. By the time I recieved the ssd windows validation time had expired, I tried to validate the version of windows and I could not because the network adapter was now gone! This is strange because when I first built it it as fine and I was all over the internet via broadband ethernet cable.Now the internet box has a red x and will not recognize the cable and no lights are flashing on the back as well. It seems I ned to reinstall the driver so I used another computer and downloaded the only LAN file from ASUS website and nothing.
View 1 Replies
View Related
May 17, 2012
I've configured in an UC520 a SSL VPN.I can access properly and I can see the labels, but I only can access urls which are http, not https:I can access the default ip of the uc520 (192.168.1.10) but When I try to get access to a secure url I get the msg: Failed to validate server certificate I'm trying to access a Cisco Digital Media Manager, whose url is URL Does the certificate of both hardware has to be the same?
View 7 Replies
View Related
Feb 9, 2011
I have some iPhone in my company and they connect to VPN through an ASA (version 8.0.4). The vpn connection use a certificate to validate that the device can connect. All my devices used the ASA IP address to connect, I decide to change that and use a name to connect ( DNS resolution made by the ISP), a generate a new certificate and made a new vpn connection profile. My PC, mac book pro can connect using the new connection, but my iPhone display the message : "Could not validate certificate". I've checked all the configuration and can't find where the difference between my two connection profile.
View 2 Replies
View Related
Feb 8, 2011
I am having a problem using my Windows IAS radius server to validate management users for my 2112 Wireless Lan Controller.I have defined the radius server and it works ok with the policy for validating wireless clients but not for WLC management users.The Remote access policy seems to be set up correctly as the event viewer on the server shows:-
Event Type: InformationEvent Source: IASEvent Category: NoneEvent ID: 1Date: 09/02/2011Time: 11:06:06User: N/AComputer: UK01DC07Description:User xxxxxx was granted access. Fully-Qualified-User-Name = TRAVEL.OAG.com/Dunstable Admins/xxxxxx NAS-IP-Address = 10.10.45.210 NAS-Identifier = UK03NM01 Client-Friendly-Name = UK03NM01 Client-IP-Address = 10.10.45.210 Calling-Station-Identifier = <not present> NAS-Port-Type = <not present> NAS-Port = <not present> Proxy-Policy-Name = Use Windows authentication for all users Authentication-Provider = Windows Authentication-Server = <undetermined> Policy-Name = UK03NM01 - login Authentication-Type = PAP EAP-Type = <undetermined>
....
But, the WLC log shows:
*Feb 09 11:06:06.612: %EMWEB-1-LOGIN_FAILED: ews_auth.c:2104 Login failed. User:xxxxxx. Service-Type is not present or it doesn't allow READ/WRITE permission..
The WLC just returns the login screen
View 7 Replies
View Related
Jan 23, 2012
i have windows 2008 R2 as CA server. and i also have 2911 router as remote vpn server. Everything works fine for desktops computers and leptops. Users automatically enroll certificates on Microsoft CA server and get connected to vpn. But problem is with ipads. When i try to connect from ipad error massage deslpays "Could not validate the server certificate" and i also get chis error massage from router "CRYPTO-4-IKMP_BAD_MESSAGE: IKE message from x.x.x.x failed its sanity check or is malformed"
With ipads built in vpn client i can see the installed certificate and use it but with anyconnect client no certificates are displayed.
View 4 Replies
View Related
Aug 2, 2011
The laptops in my flat are wirelessly connected to a Netgear N150 Wireless router and the connection is forever going from little to nothing. I've tried resetting everything, getting Orange to replace the router (a new Netgear N150) but still nothing. I've tried changing channels in the past but never seems to last. I can't work out if another wireless router in another flat is chomping into our connection
View 14 Replies
View Related
Nov 13, 2012
I have a Netgear Router at home, and both my Laptop and Tablet connect to it via WiFi. Now on both the Laptop and Tablet, Internet has recently become VERY slow. I contacted my ISP and they said everything on their side is fine, so it has to be on my side.What can cause this? I've checked for Malware but the fact that both the tablet and Laptop has slow internet points to the router. I also flushed my DNS on my laptop and booted into safemode with networking, internet still ridiculously slow.Note, both the laptop and tablet travel with me and did connect to other networks sometimes.
View 3 Replies
View Related
