When I upgraded my cisco 3750 ME from c3750me-i5k91-mz.122-46.SE to c3750me-i5k91-mz.122-58.SE2.bin all commands for radius disappeared? However, there are a lot of commands to ldap which was missing in the previous version. Seems as if the radius has disappeared and been replaced by ldap?
View 1 RepliesWe are setting up a new office and I am trying to get RADIUS setup for authentication to my switches and routers. Currently I am working on a 3750 running IOS 15 and getting hung on what I think on something small. I have attached my Microsoft NPS Network Policy. Below is my IOS config:
aaa group server radius corp-radius
server 10.15.10.20 auth-port 1812 acct-port 1813
!
aaa authentication login default group corp-radius local
aaa authentication login radius-localfallback group corp-radius enable
aaa authorization exec default group radius
[code]....
is there a way to assigen a QoS service policy via Radius to an Caltalyst 4500/3750 Switchport?
in detail, we would like to assign this policy
policy-map SET_EF class class-default set dscp ef
to an interface. All traffic should be marked with a defined DSCP value.
This works find when doing it statically with
interface FastEthernet2/1 service-policy input SET_EF
but we would need to assign such a policy via Radius during the 802.1x Authentication. different users should get differnt policies. We use Cisco ACS 5.2 as Radius Server and there actually is a field for that in the Authorization Profile Common Tasks Configuration. in detail, this uses the cisco-av-pair "sub-policy-In=<policy name>" attribute to assign a service policy to an NAS.
we found also two other attributes "sub-qos-policy-in" and "ip:sub-qos-polcy-in" for that. CCO says that "ip:sub-qos-polcy-in" works with Catalyst 65k [URL]
unfortunately this seems to not work on Catalyst 45k and 37k.
In the ACS Logs we can see that these attributes are attached to the Radius Reply, but unfortunately they are ignored by the switch.
it is interesing that when entering "show aaa attributes" on the Catalyst 45k, these attributes are displayd - so for my understanding the switch should understand these attibutes (?)
4503-E#sh aaa attributes AAA ATTRIBUTE LIST: Type=1 Name=disc-cause-ext Format=Enum Type=2 Name=Acct-Status-Type Format=Enum
[Code]......
We have configured following commands on switch to fallback to local Vlan if both radius server (policy persona's) is found dead. For test purpose we shutdown both servers (policy persona's) but fallback didn't work. We have 3750 switch running image 12.2(55)SE6 having following configuration.We do not know whether we configured switch in proper way or do we need to modify it. [code]
View 5 Replies View RelatedI have a Cisco 4402-25 WLC with the below information that is having an interesting issue. When you log into the GUI interface with the local account and click on WIRELESS, then choose a accesspoint it brings up a menu where you have three buttons below for the following options (Hardware Reset - Reset AP Now), (Set to Factory Defaults - Clear All Config), and (Set to Factory Defaults - Clear Config Except Static IP). The problem I am having is we access all of our WLC's using Radius and when you enter your AD username and password and go to bounce a access point the GUI interface is missing the buttons, they however appear fine when logged in with the local account.
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.220.0
RTOS Version..................................... 7.0.220.0
Bootloader Version............................... 4.0.206.0
Emergency Image Version.......................... 5.2.157.0
I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
View 2 Replies View RelatedI have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
View 4 Replies View RelatedI have one VLAN on a 3750 where I do not see any MAC addresses even though it is in use. This is an unrouted VLAN between a WLC on a port- channel /LAG and an access port to an ASA for guest traffic. When I do a show MAC add I get nothing for VLAN 60 (guest DMZ) but all other VLANs seem to be OK. Spanning tree is not showing TC counters incrementing either.
I also was told when put a port on this VLAN the laptop did not get a DHCP address form the ASA, but the wireless guest clients are working fine. I can see the DHCP leases and ARP entries in the ASA and the ASA ARP in the WLC so some traffic is passing fine. I'm not onsite right now so troubleshooting is all remote which limits some options.
I am currently useing ACS 5.2 and have no problem using Tacacs+ with AD access.
But with Radius it seems I can only get the Local identity store to work, need to do something special to get Radius to work with active directory with Cisco ACS?
This does seem correct. I had 2 rules and now they are gone.
View 2 Replies View RelatedI have been trying to get our IPS (ASA-SSM-10 and 4260) to authenticate with Cisco Radius ACS 5.2 and they are not working. However, I was able to get them working with Microsoft Radius. Below is the logs from the IPS:
evStatus: eventId=1321566464942057375 vendor=Cisco originator: hostId: NACAIRVIDLAB1 appName: authentication appInstanceId: 350 time: 2011/11/23 17:50:38 2011/11/23 09:50:38 GMT-08:00 controlTransaction:
[Code].....
I need to configure RADIUS VSA configuration for a my alvarion device. Following are the attributes that need to be configured.
- Packet Data Flow ID (ID 1, integer16)
- Direction (ID 4, integer8)
- Transport Type (ID 6, integer8)
- UplinkQoSID (ID 7, integer8)
- DownlinkQoSID (ID 8, integer8)
[code]....
I was able to configure the first 6 attributes, how can I add the Sub - TLV's ClassifiedID, Priority, VLAN-ID and Classifier Direction which come under Classifier. Don't see any option for that in ACS 5.x
We have 2 ACS 4.2.1 servers in Windows 2003 with SP2 installed. We have updated the first ACS to the latest patches for Windows. After that we started having problems. CSRadius either stops by itself or when some time passes we get the following error in Failed attempts "Unknown error". When we restart the ACS services by the GUI, it resumes until the next time it stops.Do you happen to know if we have any bugs related to Windows patches?
View 3 Replies View RelatedI am trying to configure AAA authentication and authorization with Cisco 3725 (IOS 12.4(17)) for 802.1x and ACS 4.2 with VLAN assignment to my Windows XP client. (trying to assign VLAN 100 in my scenario).When user connects to the Router, it passes the authentication process (EAP-MD5). In my debug i see that Router recieves the Radius Attributes BUT does not apply anything!My running config:
Building configuration...
Current configuration : 1736 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[code]......
As a result the vlan-switch data based does not change.
I have a questión about radius authenticaction with AD, when I log in into the network with user in AD and I make a mistake in password my radius authenticaction event in ACS 5.2 dont show me this logg. only show the authentication succeeded but dont show me the authentication failed. Maybe i must to enable same service to show the authentiaction failed. The Voice authetication works fine..
This is the confg in the port of the switch:
interface FastEthernet0/12 switchport mode access switchport access vlan 2 switchport voice vlan 10 authentication port-control auto authentication host-mode multi-domain authentication violation protect authentication event fail action authorize vlan 11 authentication event fail retry 2 action authorize vlan 11 authentication event no-response action authorize vlan 11 authentication periodic authentication timer reauthenticate 60 mab dot1x pae authenticator dot1x timeout tx-period 10 dot1x max-reauth-req 3 spanning-tree portfast end
Vlan 2: DATA
Vlan 10: VOICE
Vlan 11: GUEST
I have the next config of radius authentication:
aaa new-model
aaa authentication login default group radius local
aaa authorization exec default group radius local
aaa session-id common
ip radius source-interface Vlan31 vrf LEGACY
[Code] .....
I want to add Radius attribute to Rad ware devices , so I will have the option to grant "read only" permission to users. as I understand I need to add VSA for the "read only" permission, or configure specific "Service-Type value 255"
in the following picture you can see the required information from Rad ware:
I am using the Self RADIUS server in my Cisco ACS SE 4.2 appliance S. I have an AAA client C that interacts with S by means of the RADIUS protocol. This works fine, in that S correctly carries out authentication chores on username/password (PAP and CHAP) pairs received from C, sending back to C the corresponding Access-Accept packet when the authentication succeeds, or Access-Reject when it doesn't.
I have been able to import a set of three VSAs into S. Each of those attributes is of string type. I then configured in S a single user U with password P so that, whenever a U/P pair received in S from C is authenticated by S, S should send back to C, in the Access-Accept packet, the three attributes with the following values: [code]
With this setup, when an authentication is successfully completed by S, C receives 53 bytes worth of data from S every time. I am attaching a typical example, already disassembled. I have disguised the actual vendor ID, for legal reasons, but the rest is exactly as it was when received in C.
According to the disassembly, what we got is an Access-Accept packet, as expected. Its length is 53 bytes - again as expected, for this is the only packet that C has received from S here. However, the packet is incomplete, for attribute #3 is missing its value field.
Looking into the whole packet in more detail, it can be seen that while the wire format for the first attribute, namely, Frame-IP-Address, is correctly constructed, the remaining are not. For example, the sequence of bytes corresponding to the attribute #1 reads 1a 09 00 00 xx xx 2c 61 62 63. I believe that this is incorrect; it should be 1a 0a 00 00 xx xx 2c 61 62 63, for the wire format for this attribute consists of 10, not 9, bytes. I tried a few variations on the values for the attributes, and the results are always substantially the same, in that the wire formats for these attributes are always incorrect.
This all probably implies I have done something wrong when importing the VSAs into S, and/or when configuring things on S. I am therefore attaching the csv files I used to import my VSAs into S; as before, names and vendor ID are disguised, but their lengths are exactly the same as in the undisguised file. I used two csv files: One to import the vendor ID, and the other to import the VSAs under that vendor ID. As for user U, in S's administration GUI I clicked on User Setup and selected user U, moved to the bottom of the screen, where the attributes for this particular vendor were present,introduced the values for each attribute mentioned above, and made sure that button in front of each attribute was ticked.
I have a 3750 switch stack running version 12.2(53)SE2 IPBASEK9-M. I have dot1x configured on the switch and have a Windows 7 PC connected with 802.1x configured on the interface. I see the EAPoL start message from the PC, but I don't see any RADIUS packets from the switch to the RADIUS server. I have a simple dot1x config just to try to get it working prior to adding additional features such as guest-vlan...
Config and debug file attached.
I don't know if the ip dhcp snooping and arp inspection configuration is causing an issue with this or not. I see the EAPoL packet received on the switch as seen in the debug attachment, but I still never see the RADIUS packet. I did set both to trust on the interface but still the same outcome. I can't disable it since it is a production switch with a test interface.
We currently have an issue with our main ISE. When logged in using the admin account (member of superadmin group) we no longer see the Profiling button/menu and also missing oter options in the GUI. On another standalone ISE we do see al those options?
Both are running on the same software version 1.1.1.268.We are using ISE 3395-K9 appliances
Environment :AP 2602, WLC 5508 V7.4, ISE 1.1.2, Prime Infras 1.2
For a specific SSID, we use MAC address as 1 of the conditions to authorize access only for the company-owned mobiles (smartphones and tablets), the other condition being, for the mobile, to present a valid AD user/password;this way, the so-called BYODs are rejected since this is the rule within this company ;The difficulty with this approach is the fact that there is no way in ISE Identities Endpoints nor Groups to associate a user-friendly name to the MAC address of the mobiles, which makes very tedious some actions such as a search in the ISE authentication Log based on the MAC address value itself;the question is just to know if it is planned to add a new field in Identities Endpoints definition that would allow to associate a user-friendly name to a MAC address, for future ISE versions,
I need to add OPNET Radius attributes in ACS 4.2. How should I add a new VSA in ACS? The google search is pointing me to CSUtil.exe, and I cannot find this utility in the ACS install files. These are the values that I need added for OPNET. When configuring the RADIUS server to support the ACE Live Appliance, use the following Vendor Code and Vendor Specific Attribute (VSA): Vendor Code: 7119 VSA: 33.
View 2 Replies View RelatedI am trying to configure ACS 5.1 to authenticate SSL VPNs on an ASA5500 and aslo to provide admin access to the ASA5500 both via radius.I want to authenticate the VPN against a SeureID appliance and the admin login against a different database (using internal for testing but will use LDAP in the end).I cant seem to get the ACS to distinguish between the two authentication types. If I create a rule that says match protocol radius I can point that at either database but if I try saying match radius and service type 5 it doesnt match the VPN and falls through to the default authentication service. I have also tried matching service type 6 for admin and that doesnt seem to work either.In the end what I want to acheive is to authenticate teh ASA5500 VPN against the SecureID appliance and then admin access to all devices on teh newtork (a mixture of Cisco, F5 and Juniper) to active directory via LDAP where if the user is a member of the "admin" group they get access.I was intending to use specific devices for the ASA5500s (there aretwo) and then creat a device group based on IP address range for everything else.
View 4 Replies View RelatedI am trying to authenticate on Juniper NSM express using cisco ACS 5.2. The request is arriving at the cisco ACS but i am getting the following error.RADIUS requests can only be processed by Access Services that are of type Network Access.
View 4 Replies View RelatedI have CISCO ACS 5.1 radius for VPN on ASA and tried to configure an NDG on it for AIRONET 1260 too and worked fine with IEEE 802.1x CISCO EAP-FAST authentication As I had some trouble to let users to authenticate only on VPN if are VPN users and only on CISCO AIRONET if need only WIFI AIRONET I tried exception policies rules but something not working. VPN was ok but not WIFI access denied for rule policy access I decided to install CISCO ACS 4.x on Windows 2003 that is on ACS 5 DVD I created NDG as done on ACS 5 put a shared secret , put on AIRONET too as done for ACS 5 but I receive an error against ACS 4.x To troubleshout it I tried [URL] but not work ! I think to have done all fine owever on ACS 5 it worked in 5 minutes I searched log inside ACS 4 and found "Invalid message authenticator in EAP request" and I found this: [URL]Changed shared secret more times but ever not workign with ACS 4 I need to have user and password prompt on client trying to authentincate on AIRONET WIFI and I need ACS INTERNAL USER no active directory, no LDAP , no external user database?
View 1 Replies View RelatedI am having ACS 4.0.2 in my network, which I want to use for 802.1x Radius Authentication for Clients on PEAP-MSCHAPv2 methodology.As per the documentation " EAP Authentication with RADIUS Server", Doc ID: 44844.I have configured Network Configuration and populated AAA client IP range and Secret Key.
Question1: Under Authenticate Using option, there are various RADIUS flavors available for selection. For a Non Cisco AAA client, should I select RADIUS IETF?
Question 2: In the above snap shot, It has an option called Global Authentication Setup, where we can setup EAP configuration. Under PEAP subsection there is an option to "Allow EAP-MSCHAPv2" check box.After checking that, is a restart required to the ACS Server? Would it cause any disruptions to the existing services on the ACS?
is command accounting for Radius supported on ACS 5.2 ? provided vendor's radius implementation supports this capability.
View 1 Replies View RelatedI am trying to move my ISDN dialup branches authentication/authorization from old ACS 4.1 to ISE appliance. Before it was through ACS 4.2 with TACACS protocol but now since we are moving to ISE we are moving them to ISE with radius.
Problem is that isdn client gets authenticated and authorized but calls get dropped and they dont able to communicate with HO. IP address is assigned by Head End router to all remote isdn dialing branches..
I have used default "PermitAccess" in authorization policy and authentication policy is also default. I dont understand where I am going wrong as authentication and authorization is sucessful.
aaa authentication ppp default group radius local
aaa authentication network default group radius
aaa accounting network default start-stop group radius
radius-server host 12.18.22.41
radius-server key *****
I need to configure the ACS 5.1 to meet the following requirement :-
1. ACS 5.1 will point to a RSA SecurID as the first authentication mechanism for the validation of user credential
2. In the event that RSA SecurID is not reachable, the ACS 5.1 shall point to its local user database.
I had no problem configuring for Point (1), but I am not able to let it failover to the local user database.
how to setup ACS 5.3 to authenticate wireless users over radius? I currently have the SSID pointing to a Microsoft IAS server and would like to move the authentication to be done via ACS.
View 1 Replies View Relatedcurrently I'm evaluating an ACS 5.2.I need to authenticate the VPN-Users against LDAP, but have no direct connection from the ASA to the LDAP-Server. So the ASA should connect to the ACS to ask the LDAP-Identity-Store, OK.
My first Problem is: the ACS doesn't respond to the RADIUS-Requests of the ASA! ASA use's Port 1812, the Secret is ok, the ASA is as a Network Device in the ACS configured and I've created an internal Test-User on the ACS.the Firewall-Log shows the established connection (so I think, there is a Hand shake!? ), but the ASA says in Radius-Test: "EROR:Authentication-Server not responding".
getting a Cisco WLC to work with MS NPS server? We've done it before albeit with differnt code versions.
I have a Cisco 5508 WLC running 7.0.116.0 code hosting a WLAN configured for WPA2 with 802.1x for authentication. I have two Windows NPS servers configured as the RADIUS servers for EAP-TLS authentication. Via debug info on the WLC I can see the 802.1x handshake take place with the wireless client and the WLC as well as a successful transmission of an Authentication Packet from the WLC to one of the RADIUS servers. However on the WLC I see repeated RADIUS server x.x.x.x:1812 deactivated in global list and on the NPS server I'm seeing event log errors indicating "The Network Policy Server discarded the request for a user" along with the pertinent auth request info that I would expect the NPS server to receive from the WLC. Based on the WLC debug info I'm never actually getting to the EAP-TLS certificate authentication part. It seems the NPS servers don't like the format of the initial RADIUS authentication request coming from the WLC and so don't respond whcih in turn casues to WLC to switch to the other NPS server which produces the same issue.
i changed from ACS 4 to ACS 5.2. Everything works fine but i have authentication failed in the Radius accouting reports every time when users connect through ASA or Juniper into our network. Juniper amd ASA only send accounting informations to ACS. The users are not configured on the ACS, authentication is done via external LDAP. So my question is why do o see authentication error on ACS because Juniper and ASA only send accounting packets ?
View 2 Replies View Related