We are currently running ANM server version 4.1. I am trying to upgrade to version 5.1. But when I run the "application upgrade anm-va-5.1.ova Upgrade" command, I receive an error that states: "Manifest file not found in the bundle".I then tried to run the install command with the same error.
View 2 RepliesI put multiple rservers in multiple server farms?
So for example rserver1 and rserver2 are put in serverfarm production1 and are in use with particular sticky and load balancing settings.
Can I then create serverfarm test_production and put both rserver1 and rserver2 in it? Then play around with the sticky and load balancing settings as a test without affecting the production serverfarm.
I'm trying to design a CSS configuration that allows servers in the same vlan to be the source and destination of load-balanced traffic. My thought is to add two new vlans, one for the VIPs and one for the servers, then NAT the source IPs going from the LB to the servers.
Is this the right way to do it?I've never NATted using CSSs, so I wanted to verify what I'm thinking.Our current config trunks the vlans -
interface 1/1
trunk
vlan 1
default-vlan
vlan 555
[code]....
Is it possible to upgrade ACE 4710 from A3 to A4? What does this actualy means by A3, A4 & A5.
I want to upgrade ACE from A3 to A4 becase I want to enable switch-mode on ACE. Current S/W version is A3 2.0 which is not supporting this command. While reffering the command refernce guide saw that this command is supported in A2 & A4 version from 2.0 itself but for A3 in 2.7 (which is the latest) also this is not supporting this feature.
I have two GSS. One in side A and one in side B. This in side A is primary and make management function, this in side B is secondary. Site A and B are DC work in active-active.
I have version 3.1.2 and I have to upgrade to 4.1 becouse 4.1 work with DNSSec. This is true?
I read that first I have to upgrade primary. But what with secondary? How it work? When I will be upgrade primary it will be not impact to synchronization with secondary?
I am currently running A3(2.6) and evaluate the possibility of upgrading to A4(2.1). The Instal & Upgrade Guide A4(2.0) mentions that A4(2.0) does not include all features of A4(1.1). Does this apply to A4(2.1)? The Release Notes mentions a list of features merged from A4(1.1) to A4(2.1) but does not clarify if there any features not merged.
[URL]
I have a pair of ACE 4710s with 12 contexts sharing the load, running A4(2.1). esterday I upgraded one of them to A4(2.3) now I cannot telnet to the Admin context.Pings ok. I can telnet to other contexts on the box and everything seems to be working ok when i do a " sh telnet" comes back with
No Session Information is available
sh telnet maxsessions
telnet maxsessions 16
I have ACE10-6500-K9 installed in 6513 core switch with below mentioned sh version.
Software
loader: Version 12.2[121]
system: Version A2(2.0) [build 3.0(0)A2(2.0)]
system image file: [LCP] disk0:c6ace-t1k9-mz.A2_2_0.bin
[Code].....
I want to know that can i upgrade ACE10-6500-K9 to c6ace-t1k9-mz.A5_1_0 i.e version5 ? I tried to search cisco website but could not get proper upgrade or user guide.
I have a pair of ACE 4710's running software version A3(2.0). I intend to upgrade to version A5(1.2). Can I go straight to version 5 or do I need to go to version 4 and then version 5?
View 1 Replies View RelatedI need to upgrade 2 active-standby cisco ACE4710, the issue is I cannot access FTP/TFTP/SFTP server via Admin context but can be accessible via other contexts.
Can I copy the ACE system software file from FTP/SFTP/TFTP server to image: directory durectly or need some other way around ? I could see the option is available to copy ftp: to image: via other context.
Upgrading a 4710. This is a brand new ACE out of the box and I have tried to upgrade a couple of times but get the same error... Here are the details:
switch/Admin# copy ftp://10.0.0.1/c4710ace-t1k9-mz.A5_2_2.bin image: Enter the destination file name[]? [c4710ace-t1k9-mz.A5_2_2.bin]
File already exists, do you want to overwrite?[y/n]: [y] y Enter username[]? ace Enter the file transfer mode[bin/ascii]: [bin]
Enable Passive mode[Yes/No]: [Yes]
Password:
Passive mode on.EXT3-fs error (device hdb2): ext3_new_block:
Hash mark prinAllocating block in system zone - block = 163843ting on (1024 by
Aborting journal on device hdb2.
EXT3-fs error (device loop3) in start_transaction: Journal has aborted
EXT3-fs error (device loop3) in start_transaction: Journal has aborted
EXT3-fs error (device loop3) in start_transaction: Journal has aborted
[ code]......
And it keeps going on with this message. I also tried tftp and I get the same thing:
EXT3-fs error (device hdb2): ext3_free_blocks_sb: bit already cleared for block 6147
EXT3-fs error (device hdb2): ext3_free_blocks_sb: bit already cleared for block 6148
EXT3-fs error (device hdb2): ext3_free_blocks_sb: bit already cleared for block 6149
[code].....
I'm trying to upgrade my ACS 5.3 (patch 7) to ACS 5.4 and I've downloaded the application bundle from Cisco. I'm transferring the app bundle via FTP towards the VM containing ACS, yet I ALWAYS get %Manifest File not found in bundle. I've opened the bundle and found the manifest .xml inside.
I've double verified MD5 checks, size files, re-downloaded everything, even copied it to the local disk of the appliance. Also browsed through this forum to see that there are people having the same problem with other ACS version upgrades and besides re-downloading and using FTP there isn't a specific solution. I'm always getting this error. I know that it must be possible to do upgrade, but I'm stuck. I do see on the FTP server logs that the file gets transferred, but as pretty much as soon as it finishes transferring (not enough time in my view to extract a 1.2 GB file) I get an error
I'm doing the:
application upgrade ACS_5.4.0.46.tar.gz FTP
(...)
%Manifest file not found in the bundle
what the "ACS 5.2 application upgrade package" is? I've seen this package on the download software area but couldn't find any document on this.
View 2 Replies View RelatedI have a ACE20 module with a performance of 4 Gbps. I want to upgrade the performance from 4 Gbps to 8 Gbps. Is correct the following SKU for the upgrade?
ACE30-UPG-08-K9=ACE10 or ACE20 to ACE30 Upgrade for 8 Gbps Throughput
And if i want to upgrade the performance to 16Gbps is correct the sku?
ACE30-UPG-16-K9=ACE10 or ACE20 to ACE30 Upgrade for 16 Gbps Throughput
I noticed that the price list of both codes is the same....
Is it right for the SKUs listed I get the new module with the performance ACE30 requested?
We are running ACE 20 modules in highly available active / standby (all active contexts on one module) mode. Currently they are on A2 (2.4) version. We are going to upgrade them to A2 (3.6a). The question is that how ling can we run them in two different SW levels? In otherwords can we have few days between upgrading both modules?
View 1 Replies View RelatedWe upgraded a CSACS-1121 from ACS 5.2 to ACS 5.4 with CLI Application upgrade ACS_5.4.0.46.0a.tar.gz FTP After ACS reboot, services never start... After 15 hours, we always get same message:
ACS/admin# show application status acs
Application initializing...
Status is not yet available.
Please check again in a minute.
We installed patch 5-4-0-46-2.tar.gpg but we got same issue for 2 hours ...What could I do?
I want to learn how to make application server?I have Windows server 2008 enterprise edition and it is connected to 10 Client Machines. I want to install software programes only on server and use them on client machines without knowing server password.
View 29 Replies View RelatedIf we use an ACE4710 to load balance two real servers, obviously it will use health checks to determine if a server is down.When it detects a server is down, it will not send it any more traffic.But can we also have it take any other action? For example maybe email an admin, or send an SNMP trap? Or better yet, can we use a custom TCL script to do other things, like launch some custom activities?
View 2 Replies View RelatedI had a working server running ISE version 1.1.0.665 but someone in the build room decided to pull the power out of the server rather than shutting it down correctly. I have booted the server back up however the web management page was not accessable. I have checked the server status and the end result is the Application Server in the "still initializing" stage. I have left the server for several hours and the status has not changed.
I know people have previously run into this issue but no one has posted any resolution or confirmed that a rebuild is the only solution. I have tried to create an on-demand backup but it seems to fail when attempting to provide the credentials (which are correct) for the FTP server.
I have a Cisco ACE 4710 A5(1.2). Scenario: Inbound call from PSTN to SIP Phone. Call comes into the VIP and then load balances to sip server, the server then routes the call out via WAN to the SIP phone as below:
PSTN SIP Providor >(router)> ACE4710 > sip_server(s) > ACE4710 > (router) >SIP Phone
Note: Router is Cisco 3925 with "ip nat service sip udp port 5060" and Port 5060 mapped to the VIP of the ACE.If I put the sip server directly behind the router it works fine. From behind the ACE:
If I turn on sip inspect on the VIP the call setup (INVITE) and termination (BYE) work fine but the audio loops on the PSTN side from the mic to the speaker.If I turn OFF sip inspect then the audio is fine and mapped correctly but the call terminaton (SIP BYE) hits the VIP from the PSTN but never reaches the sip server.For ease and dianostics, I have turned off all sip servers except one meaning the load-balancer has only one server to choose from.SIP Call_id sticky is setup and seems to work, though irrelevent with one server only on test.How do I get the ACE to accept 'server initiated traffic' with sip inspect so it knows about the pending BYE when it comes back from the IP phone via the VIP?Config below, image attached. Bridged mode (also get the same result in routed mode)
access-list everyone line 8 extended permit ip any anyaccess-list everyone line 16 extended permit icmp any any
probe sip udp 1 description SIP Health Monitor interval 30 expect status 200 200
rserver host server1 description Production SIP Server ip address 10.44.56.172 conn-limit max 980 min 980 probe 1 inservice
serverfarm host sip failaction purge probe 1 rserver server1 inservice
[code].....
configure Cisco Ace 4710 ?Note :- Just a testing face I need to access my one server(192.168.1.11 : 80) through VIP :- 10.13.77.10 , I have only one Cisco Router 2800 and One L2 Cisco Switch 2960 and Cisco Ace 4710 . So I already configured 2 Different VLANS in Switch (Vlan 10 & Vlan 100) and by router I given the ip address of that Vlans with Inter Routing Vlan. My Connectivity is like this :-- Router Ethernet 0/0 --- 10.13.77.1/24 with vlan 10) & Router Ethernet 0/1 ---- 192.168.1.1/24 with vlan 100 ) connected with switch after that I configured ACE LB and connect the ACE interface with switch Like that ---- Connect to ACE Interface 2/3 vlan10 with switch vlan10(Ethernet port 2-12) and Connect to ACE Interface 3/3 vlan100 with switch vlan100(Ethernet port 13-24) .Testing to access server from Switch Vlan10 to Vlan 100 where my server is there.
Configuration :---
ACE> client side Vlan10 (10.13.77.4/24) , VIP :- 10.13.77.10, SM-- 255.255.255.255
ACE> server side Vlan100 (192.168.1.5/24), Web server -- 192.168.1.11 with 80 port
ACE> Managment Vlan 1000 (172.16.6.5/24) ,
ip route 0.0.0.0 0.0.0.0 10.13.77.1
I already Configured in Routed mode but From Vlan10 ip subnet example like 10.13.77.12(Client or User PC) tried to access server 192.168.1.11 with VIP http://10.13.77.10 but not responding , if i access server with real IP then accessible (why boz there is inter vlan routing)?
Access Server through VIP (ACE 4710) but very slow
Accessing the server very slow.., check my real configuration... this configuration is for application server and after this i have to configure more serverfarm for different server like webmail etc. in this ACE 4710. I have only one ACE 4710 .
ACE Version A4(2.0) = is there supports Probe with this version? without probe server will work but very slow.
VIP :-- 172.16.15.8
LB/Admin# sh run
Generating configuration....
[Code].....
We recently configured a setup to loadbalance 2 application server using ACE4710. Initially the configuration was to link two app servers directly to ACE4710 without connecting to a Switch, but later, it was advised that ACE4710 is not able to work without connecting to a switch.
1. ACE4710 is not able to link directly to APP/WEB server, but it must go through a network Switch.
2. If item-1 above is true. We used to have a older Cisco Loadbalancer which is able to link directly to WEB/APP servers. What is the reason or advantage of removing this feature?
I've been running into an issue with Cisco CSM for a number of years, but always found a way around it. Im attempting to get to the bottom of this to find out once and for all, if this is infact a limitation of the device, or a config issue/work around is possible.
Here is my situation. My CSM's are configured in bridging mode. Traffic works great, traffic bridges across vlans correctly. Everything works and have many instances of smilar configurations running in production. Every once and a while, a client requests that a "real" server (ie LWCMW-021)
cannot ping its VIP address (10.95.88.68). I am assuming this is related to the NAT Server, but not 100% sure. Clients have requested this functionality for some type of application based purpose, but Im unaware if CSM in bridging mode can provide this or not.
real LWCMW-021
address 10.95.88.59
inservice
!
real LWCMW-022
[Code]....
After upgrade from ACE20 with A2(3.5) to ACE30 with A5(1.2) I get failures in a number of server farm's, where before upgrade the number was zero. No drops in VIP and logs from applications do not notice any new errors.
View 2 Replies View RelatedI'm trying to set up a load balancer within an OVH (hoster) infrastrcture, I've followed their instructions [URL] I'm using a RIPE block (5.135.193.xxx/28) and would like the first 8(5.135.193.xxx/29) to be used as the virtual server.vlan 2676 is the local one, and vlan 1227 is the public one.After all the config steps, none of these IPs are responding to a ping, nor a direct http request.
the full configuration is :
=============================================
ssh maxsessions 1
access-list ANY line 8 extended permit icmp any any
access-list ANY line 16 extended permit ip any any
probe tcp PROBE_TCP
passdetect interval 30
[code]....
Is there a way to rename a server farm, health probe, real server or virtual service without having to completely rebuild it? I'm running 3.0(A3).
View 2 Replies View RelatedWe have two Cisco ACE 4710 and we want to install both of the devices in HA with load balancing mode.While i have done HA mode configuration between ACE 4710.But unable to configure load balancing configuration between them.i want to tell you connectivity between server,client & loadbalancer.Our Web servers are connected to VLAN 152 on the L3 (3750) switch.Which are alreday working in redundancy between other L3.And ACE 4710 it is also connected to vlan 150 which are connected to same L3 (3750) switches and users are also connected to vlan 6 on the same L3 itself.
View 2 Replies View RelatedHow do you access an application that is in the server? Like what extra steps you gotta make? Are they software related or do I have to do some configuration on the router or switch? Heres a little example:
Assume you have a group of computer connecter to a switch, this switch is connected to a router which has the connection to your ISP. On the router, you also have connected a server farm for your network and all the apps are stored there, say MS Word, Excel and such.Now, you have your network running, every ping comes out successful, so you know you did that part right, so the next part is to get the host use the MS Word or any other app in that server. How do you do that? Is there something that need to be configured on router/switch or is it with a software on your host? If its a software, whats the name of it and how you make it work?
We have a CSS11503 that is currently being used to accept incoming HTTPS and SSH connections on a specific VIP and then PAT those client connections. I understand that it also PATs the server initiated connections. [code]
View 1 Replies View RelatedHad setup my ACE ,to send traps to SNMP server .but dont see any logs on the SNMP server from ACE.
SNMP configuration on ACE
logging enable
logging buffered 6
logging host 10.12.40.12 udp/514
[code].....
Im trying to configure an ACE 4700 so that SSL termination is done on the ACE and HTTP reaches the weblogic server instance. I have a working setup of a Apache reverse proxy doing SSL offloading and using a weblogic module and that works fine Was reading [URL]. Any working config example for doing this with the ACE4700
View 2 Replies View RelatedI have a problem with that the ACE20 (A2(3.2)) does send the connections to a backup real server in the serverfarm. I will how to troubleshoot in this case ? This is serverfarm configuration.
serverfarm host fix-http
failaction purge
probe PROBE-TCP-80
rserver fix11
inservice standby
rserver fix12