Cisco Application :: CSS11501 Redirect Preserving URI

Oct 19, 2011

I have a application where I have to redirect a specific URL to another. The point is that the primary URL, have some information that I want to preserv after redirection, for example: url...
 
The default CSS11501 behavior is to redirect the primary URL to http://xyz.com. Just that.

View 1 Replies


ADVERTISEMENT

Cisco Application :: CSS11501 Dual Network Connection

May 24, 2011

I have CSS CSS11501 which is working fine in single arm deployment. Now I want to have redudency so that in case the switch 1 where CSS is currenlty connected is down.I can reach the CSS through the second switch 2.Both the switch are trunk with each other and CSS has one port connected with Switch 2.

View 2 Replies View Related

Cisco Application :: Several Pairs Of CSS11501 And 11503 In Network

May 21, 2012

We have several pairs of CSS11501 and 11503 in our network.This issue affects only one pair of CSS11503 in one of our data centres. [code] We use vrrp in one-armed mode for load balancing and they units have performed great for a number of years. We're obviously going to be migrating to ACE ... but not just yet.We have started to experience a problem with replicating the configurations between two CSS11503 in a pair.When running the commit-VipRedundConfig, it starts off happily enough, though slowly.Ending with "working" and the spinning cursor, even after 1 hour the script hasn't completed.We noted on the backup CSS that the APP configuration disappears during the process and I can't remember if this is normal behaviour.
 
Re-adding the app session configuration seems to interrupt the process, and when checking the configuration on the backup CSS approximately half of it is missing. Everything after the first owner is gone.

1. Configuration is too large, or just large enough to make the commit script take too long for realistic service.
2. Software bug?
3. Combination of both.
4. From now on manually add config to both CSS's and maintain it by process management.

View 5 Replies View Related

Cisco Application :: How To Make A Redundant Connection To A CSS11501

Feb 20, 2012

I require to connect a "css11501" two core switches to provide redundancy to the load balancing service and would like to verify this possible (Does the spanning-tree protocol officer for load balancing?)

View 2 Replies View Related

Cisco Application :: How To Capture Packet In Load Balancer CSS11501

Jan 15, 2012

how to capture the incoming and outgoing packets on the balancer?The load balancer is connected in between the customer DCN and cisco switches 2960.The reason of capturing both incoming and outgoing packets on the balancer is to prove to our customer that there is no packet loss issue on the balancer, and it could be some issue on their DCN network.Since it is a production server, I will need to ensure that there is no impact to the incoming and outgoing traffic on the balancer and other networking equipments as well.

View 1 Replies View Related

Cisco Application :: CSS11501 One Arm Configuration For CSACS Radius Authentication

Nov 5, 2009

Is it possible to deploy the CSS11501 in one arm design to loadbalance the authentication traffic Radius across CSACS servers which is on UDP 1645 or 1812 port, is it required to configure the NAT or not, if yes how can define the shared secret in the CSS. also tell me how to configure the keepalive for udp traffic in this scenario other then default icmp keep alive

View 2 Replies View Related

Cisco Application :: CSS11501 Commit Vip Redundancy Script Failure?

Jun 23, 2011

recently when i run the commit vip redundancy script, i encountered the following error. This script has never failed in the past. Upon checking the backup CSS, i did notice that my most recent changes were actually synced. The following is the debug i have captured while running the script.

active-lb# script play commit_vip_redundancy "local 167.168.165.10 remote 167.168.165.9 -a -d" active-lb# Checking available disk space on systems ... Checking the disk space locally before continuing with the script. Verifying that another local session is not running the script. Creating script/vipr_config_sync_lock file. Verifying app and redundancy configs ... Verifying that app session is up with backup switch. Making sure app session is up. Seconds to wait before calling it quits:    60 Checking the disk space remotely before continuing with the script. Checking local and remote switch versions ... Storing the running code versions of the local and remote switch. Storing the local switch's version. Retrieving the remote switch's version. Checking remote version for 4.0 Checking if switch is BACKUP for any virtual routers and if the state is 'No Service'. Checking vip redundancy state.... Checking if backup switch is Master for any VRIDs. If it is, either a local

[code].....

View 1 Replies View Related

Cisco Application :: Configuring URL Redirect On ACE 30 Version A4 (1.0)?

Dec 18, 2011

I have a problem configuring URL redirect on ACE 30 (Version A4(1.0)).When a user enters IP address or a name of  a service [URL], the ACE module should redirect him to the page [URL]. Here is my non-working config:
 
access-list OUTSIDE line 8 extended permit tcp any any eq https access-list OUTSIDE line 16 extended permit tcp any any eq www access-list OUTSIDE line 24 extended permit icmp any any
probe http Test_HTTP_1  port 80  interval 60  passdetect interval 30  passdetect count 2  request method head url /index.html  expect status 200 200  open 1
rserver redirect URL_Redirect_01  webhost-redirection [URL] 302  inservicerserver host S1  ip address 10.0.0.2
inservicerserver host S2  ip address 10.0.0.3

[code]....
 
it works, ACE load balances to rservers. Of course, user must enter full url.With redirection configured, user recieves HTTP url redirect message with correct address [URL], but his browser does not display the page. Even directly entered full url does not display it while redirection is configured.Alternatively, does ACE30 already support url rewrite?

View 8 Replies View Related

Cisco Application :: ACE 4710 With HTTPS Redirect

Sep 20, 2011

i have ACE 4710 appliance that terminate SSL and the connection to the servers is http.
 
The ACE (one Armed) is load balancing between two web servers and i am using stickness in order to take the connection on the same server based on cookie.I can access the website either by http or https., where on the web page there is a login credential to access using username and password.
 
When i access the website using https everything works fine and i can login to my account in https mode.When i access the website through http and login to my account the URL is redirected to https...normal because i am using action-list to rewrite the http into https. But when i exit the browser and access the website again using http it is not redirected to https(although i see that i am still login into my account i can see all the inforamtion in my account).
 
The customer wants the connection to be https even when i exit the browser and access the website again (within short time before the cookie exipres)

View 3 Replies View Related

Cisco Application :: CSS Or ACE 4710 Redirect HTTPS To Http

Feb 27, 2012

For a CSS with a SSL module (performing SSL termination) - is it possible to impliment a redirect on https URL to send to equivalent http URL.If my understanding is correct, the CSS will do SSL termination and then use an http content rule on the resultant http stream as it is recursively handled by the CSS ? This would mean that the SSL module has no way of seeing/acting on layer 5 and above data (i.e. picking up on a specific URL) and can not itself issue a redirect - i.e. you could not associate a redirect statement or service with the following ssl content rule ? [code]The CSS would instead rely on a http content rule to impliment a redirect - i.e. you would have to associate a redirect statement or service to the following http content rule instead?
 
But if the CSS is already handling traffic for existing url...  traffic that is going to cause a loop when a client goes direct to. url...I realise the requirment is uncommon / a bit convoluted, its one of those don't ask type scenarios - aimed at achieving a specific requirement.Would the ACE 4710 be able to handle such a scenario any differently ?

View 7 Replies View Related

Cisco Application :: ACE 4710 - Redirect HTTP To HTTPS?

Jun 21, 2012

I am trying to make a redirect from http to https. the goal is whenever a user writes in http://10.80.199.71 it should be redirected to https://10.80.199.71 I am just haveing some trouble making it work.

View 4 Replies View Related

Cisco Application :: ACE 4700 Redirect HTTP To HTTPS?

Feb 6, 2013

How to configure a redirection on the ACE from HTTP to HTTPS using specific URL example [URL] to [URL], the SSL certificates were installed on the servers.

View 7 Replies View Related

Port Redirect With Default Ports On Application?

Apr 26, 2012

I'm running several game and file servers via a dynamic IP, which I unfortunately cannot change to a static connection for several reasons. I've solved this by using No-IP, which is a Dynamic IP resolution service. This solved the first part of my problem - I can give people IP's for their websites, such as myfreemusic.sytes.net and so forth, but they all HAVE to append their ports to the url - i.e.

site1.sytes.net:90
site2.sytes.net:91

My main problem right now is the game servers - I'm hosting games that default host to 25565, and though I can change the ports the server hosts from, I must give those who want to connect the ports at the end of their urls, i.e.

server1.sytes.net:25566
server2.sytes.net:25567

I know DNS is essentially agnostic when it comes to ports, so no solution there. And I don't think the game (Minecraft vis-a-vis bukkit) supports SRV records, and even if they did, I'd have no idea how to configure them. How can I resolve static urls redirecting to a dynamic IP by pointing them to ports?

To simplify the question -

How can I make server1.sytes.net resolve to port 25566, and server2.sytes.net resolve to port 25567 when the default port is set to 25565?

View 1 Replies View Related

Cisco Application :: ACE 4710 / Redirect All Connections From Port 443 To 9443?

Sep 13, 2012

I must  redirect all connections from port 443 to 9443.
 
this is configered and running:            
 
serverfarm host FARM-002
  probe test-xml
  rserver svx-xmlfw-lb-01 9443
    backup-rserver svx-xmlfw-lb-02 9443
    inservice
  rserver svx-xmlfw-lb-02 9443

[code]....
     
I have in the moment following problem. All connections become redirectet to port 9443 but port 8080 shouldn`t be redirectet to port 9443. What can i change in my config to solve this problem?

View 6 Replies View Related

Cisco Application :: ASR1002 / ESP2 / Getting Error Log When Change Redirect ACL Entries

Aug 7, 2011

I've configured WCCP2 on my ASR1002/ESP2 and works fine. But got error log since I changed redirect ACL entries. Check on Cisco seems it a known bug?[URL] And seems any change on WCCP not take affected anymore. Even I removed all WCCP configure on my router, but my cache engine still got the redirected packet!?
 
Aug  8 22:41:00 CST: %FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image:  Batch type 6 ID 0  download to CPP failed
Aug  8 22:41:30 CST: %FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image:  Batch type 6 ID 0  download to CPP failed
Aug  8 22:42:00 CST: %FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image:  Batch type 6 ID 0  download to CPP failed
Aug  8 22:42:30 CST: %FMFP-3-OBJ_DWNLD_TO_CPP_FAILED: F0: fman_fp_image:  Batch type 6 ID 0  download to CPP failed

[code]....

View 1 Replies View Related

Cisco Application :: Apply Policy Only On Specific Subnet / Port 443 Traffic Can Be Redirect And Rest

Feb 16, 2012

I am facing problem with ACE configuration. I want to redirect 443 traffic to my Proxy Server. But I am not able to do this. I want to redirect only subnet 192.168.80.0/24..Then only it is working but I dont have to have this policy to be applied on all the users only one subnet I want to have under HTTPS policy.
 
how can I apply the policy only on specific subnet so that port 443 traffic can be redirect and rest of all subnets can go direclty to Internet.

View 8 Replies View Related

Cisco Application :: 11500 / Redirect SSL From Base Site To Different Page On Same SSL Site

Aug 24, 2011

I'm attempting to redirect SSL from the base site to a different page on the same SSL site.  I want to redirect https://10.4.16.54/* to[URL] .  If I enter[URL], site loads, but if I enter simply https://10.4.16.54, it times out.  The ssl_sharepoint service is my ssl_proxy_list. 

  content Sharepoint_https
    flow-timeout-multiplier 10
    sticky-inact-timeout 35
    vip address 10.4.16.54
    application ssl

[code]....

View 5 Replies View Related

Cisco Infrastructure :: CSS11501 Not Working With New Windows 2008 R2 Servers

Jul 8, 2012

We're using a CSS501 to load balance http requests over three servers running windows server 2003 and IIS 6. On Saturday I attempted to switch over to three new servers running the app on Server 2008 and IIS 7.5, I mirrored the used the existing setup to create the new environment (pwgecashwww01,02,03 Owner ACMENewServers and group NewServer).

View 2 Replies View Related

Cisco Application :: ACE20 - Config Application In Progress Message

Dec 3, 2012

Everytime I make a config change to one of the contexts on our ACE20, I get this message: Config Application in Progress. This command is queued to the system
 
If I run show download info, I get:
 
context : context1
Interface                     Download-status
--------------------------------------------------------------
187                         In Progress
199                             Pending
 
Regex download optimization status : Couldn't get status[TNRPC Timed out]
 
It eventually seems to complete, but it takes a very, very long time. We are running Version A2(3.5) [build 3.0(0)A2(3.5)].

View 2 Replies View Related

Cisco Application :: Application Slowness Through ACE 4710

Mar 27, 2013

Report run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.

View 6 Replies View Related

Cisco Firewall :: IP Redirect With PIX 515?

Jan 3, 2012

I have a PIX 515 that i need to use as an ip redirector.For example if users try to access 80.80.80.80 ,they need to be redirected to 90.90.90.90 show ver, 
 
Hardware:   PIX-515E, 128 MB RAM, CPU Pentium II 433 MHz
Flash E28F128J3 @ 0xfff00000, 16MB
BIOS Flash AM29F400B @ 0xfffd8000, 32KB
  0: Ext: Ethernet0           : address is 000b.5fad.0c99, irq 10
1: Ext: Ethernet1           : address is 000b.5fad.0c9a, irq 11

[code]....
 
This platform has an Unrestricted (UR) license.

View 12 Replies View Related

IP Redirect Or Forwarding From A To B?

Oct 24, 2012

ip redirect or forwarding. I have a web server with public IP as B.B.B.B, and I have another server with public IP as A.A.A.A.. My web site contents are with B.B.B.B, but I do not want to expose IP B.B.B.B. Users can visit my web site using A.A.A.A, and when they visit A.A.A.A, I would like to have A.A.A.A redirected to B.B.B.B behind scene. Both IP's are public, and stay different locations remotely.How to redirect IP A to B, so I can hide B?The machine with IP A.A.A.A is windows 2003 server standard.

View 5 Replies View Related

Cisco WAN :: 800 Router - Redirect URL To IP Address?

Oct 18, 2011

Is it possible in Cisco 800 Router to redirect a website request coming from a user to an IP address?

View 3 Replies View Related

Cisco VPN :: Redirect On ASA 5520 For SSL VPN Clients

Dec 26, 2011

You have a Cisco ASA 5520 where clients connect using Cisco Anyconnect SSL VPN, say the URL is connect.whatever.org. You would like for when a user enters either [URL] or just connect.whatever.org into their web browser that it automatically puts the required url...

View 1 Replies View Related

Cisco Firewall :: DNS Redirect On ASA5505?

Feb 29, 2012

I want to make it so if a user tries to use a different DNS server the request will be redirected to the one they should be using.I thought this might work but the ASA doesn't do PB routing
 
ip access-list extended transparent_dns
permit udp any any eq 53
route-map redirect_dns permit 10
match ip address transparent_dns
set ip next-hop ip.of.your.server
route-map redirect_dns permit 20

[code]....
 
The DNS server is windows 2003?Would policy based NAT or WCCP work for this? If so how would I go about it?

View 1 Replies View Related

Redirect To Another Site In The Same Server?

Apr 12, 2011

How do I redirect the visits to a specific homepage (web site) to access a "sub" page in the same domain? Is it possible to use the Hosts file to do this? I want redirect visits to [URL]

View 5 Replies View Related

Forward Or Redirect From IP To Domain Name URL?

Oct 15, 2012

What the most cost and time effective way to have an ip request return with another ip address from outside the WAN of the router.Specifically want to have an application request for example 192.168.1.121 and have 173.194.43.41 respond and communicate with the application instead. To make it a bit more interesting I'd like actually to set a table or config file to point to a domain name (url) which gets resolved as an ip address. (Port independent)To get a better understanding:one example might be typing in 192.168.1.121 in a browser and googles search engine comes up on the browser.another example might be typing in 192.168.1.121 in an ftp client and it hooks to an ftp server on the other side of the world which resolves to [URL]. I was looking at openwrt and tomato a little but I don't think I have such a complete grasp on how to do it in general. Being that it seems they are 2 different layers of the network model, I was told it can't be done but I don't know if I can believe that yet. Either by third party software or reprogramming the router or adding another device to the network.

View 3 Replies View Related

DNS Redirect To Dedicated Connection?

Jun 15, 2012

I currently have CenturyLink (Qwest) DSL (12Mbps/896Kbps) and Comcast Cable (12Mbps/2Mbps) going into a Cisco RV08. I redirected all DNS traffic to the DSL line as an experiment with no decrease in web browsing speed. e are rural and speeds fluctuate considerably during the day. It seems like it's more of a response issue than a bandwidth issue. I would like to order a 2Mbps dedicated line from Comcast to use for DNS and VOIP traffic only, the DNS resolution times should be faster on that connection. There would be several tenants in this building using it for that purpose. The secondary purpose of this line would be for backup internet connectivity

View 1 Replies View Related

D-Link DIR-825 :: Possible To Have (again) Usual Redirect After Log In

Nov 2, 2011

I wonder if is posible to have (again) the usual redirect after log in. On DIR-635, DIR-855 after log in you get redirect to the STATUS if WAN connection si functional, else you get SETUP. Now, on DIR-825 even if WAN is active/functional the redirect is to SETUP page.

View 7 Replies View Related

DNS Redirect With SonicWall TZ210

Dec 11, 2012

It's been awhile since work has thrown me a curve ball so I was about due. We've got a client that wants us to log into their secure portal, this is normally not a issue. The link they sent us to their 'portal' apparently takes us to the wrong page. Their solution to this is for us to create a DNS entry to resolve that URL to a specific IP address. We don't currently have a DNS server setup in house so I assumed this would be something done on the Sonicwall.

I asked them why I couldn't just go to the IP address instead of the URL anyway and they said it wouldn't work. Is this something that I can maybe create a NAT Policy for and have it redirect traffic to there? I know the SonicWall has a DNS tab but I've never touched it and I'm not sure what I would need to put in there anyway.

View 7 Replies View Related

Cisco Routers :: Redirect Web Traffic On SRP527W

Mar 16, 2012

Is it possible to redirect all web traffic to a Symantec web filtering address on a particular listening port. I had a look at the Srp527w Router and can't find where this could be done.

View 1 Replies View Related

Cisco Wireless :: Redirect To Web Authentication WLC 2504

Apr 4, 2013

We have a WLC 2504, since a few months, it was working fine, we have a guest Wlan configure with web authentication and the DHCP scope for this in the WLC. The problem today is that its no redirecting the web browser to 1.1.1.1, we try it with 3 laptops and they recieve a correct IP from the DHCP but still can not get redirect to the web authentication portal. Have the default configuration Internal (Default).
 
In laptops we check the firewall, dont have a proxy activate and have google DNS.. 4.2.2.2 8.8.8.8. In fact this laptops connected to this ssid before.

View 1 Replies View Related

Cisco Wireless :: Wap121 Url Redirect Gone After Upgrade?

Jan 9, 2013

I upgraded the firmware on my wap121 and the URL redirect option is now gone.  The docs all talk about using Captive portal but that is only on a wap321.  How can I get the redirect back so customers who connect to my network see the site for our bar before they go on the internet?
 
I upgraded from the 1.0.0.3 to the latest (1.0.2.3)

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved