Prime 1.3 (POC testing), for testing purposes I discovered a class C range (255.255.255.0) containing a bit of everything (AP 1240, C3560 & C3750).When looking in the config archive only the AP's have configs stored, the others failed, snmp & telnet credentials are the same for the whole range, what could I do wrong ?
View 5 RepliesI have two layer 3 switches C3560 and C3750 Cisco switches with ios version "ipservices-mz.122-35.SE5".Now with the current ios version, these layer 3 switches are not supporting object group.so my question is , do i need to upgrade the ios, for this feature, if yes, which version ?
View 7 Replies View RelatedOn my study lab I have got 2 switches a c3560 running IOS and a c2948g-ge-tx running CatOS. Both switches has SFP ports, I would like to configure ether channel between them switches using 2 SFP ports on each switch.
My question is if such configuration is possible and how to configure ether channel so that VLANS can travel between both switches running different operating system. I have tried but it's no working,
We have a Cisco switch in each office and every now and then the port that has the D-Link Wireless AP (DAP-1522) connected to it goes to err-disable state. Actually sometimes even a regular port that has a cisco phone connected may also go to err-disable state (less often). So I have to telnet into the switch and issue shut and no shut command on that interface to get it back to life, then it works for a few days or weeks until it happens again. Any suitable configuraiton for that interface, that would prevent that from happening or a workaround ?
Here's the info:
Model: cisco WS-C3560-24PS and cisco WS-C3560-48PS
Image:c3560-ipbase-mz.122-35.SE5.bin
This is the log from one switch:
31w5d: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/2, putting Fa0/2 in err-disable state
31w5d: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 74e2.f592.f7f2 on port FastEthernet0/2.
31w5d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
And from another, which is almost the same:
5d10h: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/3, putting Fa0/3 in err-disable state
5d10h: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address d8a2.5e31.2cf6 on port FastEthernet0/3.
5d10h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down
5d10h: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Here's the configuration of fe interfaces (they are all alike):
interface FastEthernet0/2
description Voice & Data Combo Port
switchport access vlan 11
switchport mode access
switchport voice vlan 15
[code]....
I am having troubles to get 2 C3750-X switches WS-C3750-X-48P-L) to stack. They are both running iOS 15.0(2)-UNIVERSALK9, and are licensed for IP Base.
If I connect stack port 1 of switch 1 to stack port 2 of switch 1, and stack port 1 of switch 2to stack port 2 of switch 2 I get the following:
WS-C3750-X_STACK1_SW1>show switch stack-ports summary
Switch#/ Stack Neighbor Cable Link Link Sync # InPort# Port Length OK Active OK Changes Loopback Status
[Code].....
I have tried restarting (powering off for about 1 min and turning back on) simultaneously, and powering off switch 1 for 1 min and switch 2 for 2 min. I have also tried both enabling the stack ports, and disabling followed by enabling.
We have a bunch of switches that are running fine but the running-config file is missing and we can't save the config to the tftp server. IOS is c3550-ipbasek9-mz.122-37.SE1. I've got lots of these switches running the same code that are just fine.
View 8 Replies View RelatedI am using Prime LMS 4.2.2 software to archive configuration for my cisco Network Device switch and firewall . All works fine except for two new Cisco ASA 5525 and ASA 5545 ( Software Version 8.6.1.2 ) . I have already checked credential , ssh access , snmp configuration and all seem correct. But Archive configuration job end with failure. This is the error message:
View 1 Replies View Relatedworking with a trial version of Cisco Prime 1.2. I am looking for a Configuration Compliance tool. I used it in Cisco Works LMS - but I dont see a way to do the same thing with Cisco Prime.
View 1 Replies View RelatedI'm currently running CiscoWorks LMS 4.0.1 on Windows 2003 under VMware and just got upgrade licensing for Prime Infrastructure 1.2. I am assuming that I will need to upgrade the current server to Prime LMS 4.2 in order to ensure that data migration to Prime Infrastructure goes well. I am planning to follow Cisco's recommendation to run Prime LMS and Prime Infrastructure in parallel for a time and migrate individual functions.
My real question is about Syslog handling. All of the managed devices are currently sending Syslog data to LMS. As a last step in the migration, is it possible to change the IP address of the Prime Infrastructure server to replace the Prime LMS server so that the Prime Infrastructure server will just start getting all the Syslog data, or do I need to go change hundreds of managed devices to point to a new address?
What is the relation between: cisco NCScisco Prime LMSCisco Prime infrastructure.As i orderd a Cisco Prime infrastructure from a Cisco Partner and what i got is :
x2 cisco NCS appliances
x1 DVD cisco prime infrastructure
x1 DVD Cisco prime 4.2
Cisco cannot login? Currently i cannot login to the two of my cisco 3560 with the password that i usually used to login. and it is strength to me that its Configuration register is 0xF.
[BEGIN] 10/4/2011 10:22:57 AMshoTC-NGN-C3560-1>show verTC-NGN-C3560-1>show version Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2007 by Cisco Systems, Inc.Compiled Thu 19-Jul-07 18:15 by nachenImage text-base: 0x00003000, data-base: 0x01300000
ROM: Bootstrap program is C3560 boot loaderBOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SEC, RELEASE SOFTWARE (fc4)
TC-NGN-C3560-1 uptime is 50 weeks, 6 days, 9 hours, 34 minutesSystem returned to ROM by power-onSystem image file is "flash:c3560-ipservices-mz.122-35.SE5/c3560-ipservices-mz.122-35.SE5.bin"
[code]....
I have got my ccna voice lab configured and is up and running, my switch is configured with 2 differents Vlans (Data & Voice) and the fa 0/1 is configured as trunk port connecting to the CME router. I can telnet or ssh to all the devices on the network but only the switch in not accepting the request the only message I am getting is "request timeout".
View 12 Replies View RelatedI have a 3560-8PC in which the mgt vlan randomly (twice in one day or 2 weeks later) goes into the down state and will return w/o any interventaion 15-20 minutes later. Int G0/1 is the uplink to a 3750. I dont think its a layer1 issue at this time since i have seen it work just fine for over 2 weeks and drop again. I don't see any errors on the 3750 either.
WS-C3560-8PC 15.0(2)SE C3560-IPBASEK9-M
LOG:
----------------------------------------
.Oct 20 19:34:37.533 EDT: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changeds tate to up
[Code].....
I was working with Opmanager software to monitor my network, and i downloaded the Netflow plugin, i tried to enable the netflow on my core switch c3560 but I was surprised that it does not support the NetFlow, after many resersh most of URL's say it does not support until i found another URL from Cisco Says that it support Flexble netflow now, but i think we should update the IOS.
[URL]
I have some c3560 with system MTU set 1546 with interface VLAN10 whose MTU size is 1546 and there is no possibility to change it to another value. and we have some cisco 2600 where I can't set MTU bigger as 1500. I have a problem in establishing the OSPF adjacency between cisco 2600 abd 3560 , the command "ip ospf mtu-ignore" is set on both side but it doesn't work - the OSPF packets which are sent by c3560 are simply lager as 1500 bytes and are dropped by cisco2600.
the problem is that sometimes c7200 losses their BGP session, I would say in most cases it happens between NPE400 and NPE-G1/G2 whit error message like "session closed by a peer x.x.x.x" after some seconds BGP session goes again UP , and then after some minutes again DOWN .
it can be MTU problem, as the traffic passes those c35660 with MTU1500. The neighbour status showes that "transport tcp path-mtu-discovery" is enabled an all neighbours but it seems doesn't work. if I disable the path-mtu-discovery on the neighbours - the BGP session between them stays stable.
1.Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(25)SEE2, RELEASE SOFTWARE (fc1) This switch EIGRP coverge is slow.
2.Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1) This switch EIGRP coverge is fast
The IOS have effect of the EIGRP coverge ? From which version IOS began ?
I have C3560 switches in my work environment. I want configure ssh on that switch but the IOS what they have 'c3560e-universal-mz.122-58.SE2' not support. As per advised I was triying to upgrade 'c3560e-universalk9-mz.122-58.SE2" for all my access switches.
I successfully upgraded for two switches.
I have two problems now
01. I upgraded the IOS successfully one Switch but the Poe is not working. What is the reason ?
02. After upgrade the IOS, the out put is as follows
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 30 WS-C3560E-24PD 12.2(35)SE5 C3560E-UNIVERSAL-M
Cisco#sh boot sys
[Code].....
recently i do some lab about trunking protocol using Layer 3 switch C3560 and layer 2 switch C2960, but i face a problem that i cannot configure trunk port on my C3560 using "switchport mode trunk" command, and after looking for the answer from google i found that i have to "remove" the "auto" mode of C3560 using "switchport mode dynamic desirable" and after that we can enter the "switcport mode trunk" command successfully.
and my question are, whether the "auto" trunk mode in switch layer 3 is a default mode or not? and why i should enter "sw mode dynamic desirable" command before "sw mo trunk" command ?
I am in a doubt if the 3560-12-PC-S supports OSPF. Datasheet says we need IP Services image. But 3560-12PC doesn’t have the option with IP Services. Then I havigate to [URL] how?
So, any clues whether or not this box can run OSPF?
I am unable to login to switch c3560 through Hostname but able to login through IP address. when i am putting the command : login authentication telnetpwd
getting the below message:
AAA: Warning authentication list "telnetpwd" is not defined for LOGIN.
I have below switch and I was interested in configuring GRE on one of the interface. So I tried to create tunnel interface, the tab completes the command. Is GRE supported on this switch and IOS?
Switch#show version
Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
......
cisco WS-C3560-48TS (PowerPC405) processor (revision G0) with 122880K/8184K bytes of memory.
Switch(config)#interface tunnel 0
^% Invalid input detected at '^' marker.
Switch(config)#
IP routing is also enabled.
Is it possible to reduce de recoveery time after an interface shutdown? Current interface configuration is as follows and it takes 1 second to recover from a shutdown. I need to decrease this time.(Cisco Catalyst C3560) [code]
View 1 Replies View RelatedI have a weird situation with some switches.
Switch .55 can ssh into Switch .57 but cannot ssh into Switch .56.
Switch 56 can ssh into Switch 55 and ssh into Switch 57
Switch 57 can ssh into Switch 55 and ssh into Switch 56
The software on .56 is:
C3560 Software (C3560-IPBASEK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
I noticed on .56, when I do a show ip ssh I get: SSH Enabled - version 1.5. It doesn't say version 1.99 like the others even when I configure version 2. Is this a bug I am running into?
I am upgrading the network equipment at my place of employment. We use Cisco C3560, 2960, 4506 and I was noticing that IOS 15.0.x is available. After doing some reading it appears that Cisco is going to a pay for the licensing functionality that you want. Do I need to purchase licenses to upgrade from IOS 12.X to 15.0.x to maintain functionality?
View 4 Replies View Relatedhow to configure SLA monitorin for Dual Path default route in Layer 3 switches, like C3560?
View 2 Replies View Related#sh run | inc user
!
username USER0 secret 5 $1$passwordusername USER1 privilege 15 secret 5 $1$passwordusername USER2 privilege 15 secret 5 $1$password
!
#sh run | inc aaa
!
aaa new-modelaaa authentication login local_authen localaaa authentication login radius_authen group radius localaaa authorization consoleaaa authorization exec local_author localaaa authorization exec radius_author group radius localaaa session-id common
!
#sh run | begin line vty
!
line vty 0 4access-class 3 inexec-timeout 15 0authorization exec radius_authorlogging synchronouslogin authentication radius_authentransport input sshline vty 5 15!sh verCisco IOS Software, C3560 Software (C3560-IPSERVICESK9-M), Version 12.2(55)SE6, RELEASE SOFTWARE (fc1)
the intent of the above is that management connections will only be accepted via SSH, and all of those will be authenticated via RADIUS, unless it's down, then it will use the local username/pw combinations, most of which are given Privledge level 15. Telnet should never work.SSH works as expected (authenticates via RADIUS), but the problem is that Telnet also works, will ONLY use the local database (never RADIUS), and, for some reason, leaves the users at Privledge level 1, instead of the configured 15.Essentially, it seems that at every point I have told it to do something that isn't the default with regards to telnet, it ignores me.Prior to a recent IOS upgrade, the switch didn't support SSH, so the previous config was Telnet with RADIUS, and that worked fine.
Had a switch die over the weekend, a c3560, per our normal procedure I pulled the hardware put a very basic config on it(vlans, portchannel, uplink ports, ip of management vlan, con and vty security, snmp, enable secret, and hostname). Then I use solarwinds orion to upload a copy of the old config to bring the switch back to the same state as the one that failed. Its a system that has worked for us 3 or 4 times in the past. But this time when the base config was on the box it couldnt ping across the network.I have tried clearing the arp cache and the dynamic mac tables, i verified the routing tables and even removed the 10.1.185.128/27 route and re-added it, saw the routing update go across to the other 65k, tried bouncing the edge switch(i cant bounce the 65k's), took down the po between the edge and 65k.
View 2 Replies View RelatedI have a network running some 20 switches, two controllers and many AP's. All the devices that should be able to connect to cisco network assistant can successfully. However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology.
As far as I can see the config is identically to all other similar switches in the network. I can telnet from a switch (management VLAN) to the switch in question. However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful. However I can ping/telnet to all other cisco device from this PC. The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.
sho run
Building configuration...
Current configuration : 7363 bytes
!
version 12.2
no service pad
service timestamps debug datetime localtime
[code]......
I have a c3560 switch that has two gig fiber modules in it. I need to uplink fiber to one of these at 100mb. This is because this port will be rate limited to 20mb and 10 percent is the lowest you can go with the rate limiting command. Is there a 100mb fiber module i can insert in the 3560
View 1 Replies View RelatedWe are seeing output drops on a C3560 switchport, this port does not have QoS enabled -- application does not need special qos treatment, as long as packets are not droppd, so I suppose all traffic will share the same queue? then how should I read the output of "show platform port-asic stats drop" which indicates that it is queue 3 weight 2 drop? I am wondering what is the best way to fix this? enable mls QoS and increase queue 3 bandwidth share on this interface or just increase the output queue depth?
switch#sh mls qos interface gi0/1
GigabitEthernet0/1
QoS is disabled. When QoS is enabled, following settings will be applied
trust state: not trusted
[Code]......
I am having an issue with VoiP phones giving me an insufficient bandwidth message. I have three remote locations connected to our main building using 2 Mb point to point ethernet solutions through TWC. Each remote location has a Cisco WS-C3560-24PS running IOS C3560-IPBASE-M, version 12.2(25) and have the cable modems plugged into port 1 on them. The remote buildings are labeled 192.168.101.xxx, 192.168.102.xxx, and 192.168.103.xxx. There are 14-16 VoiP phones in each remote building. The main building being in the subnet of 192.168.100.xxx. I have the 3560s connecting to a single port on a 2801 in the main building, all using the subnet of 192.168.253.xxx The phone server sits in our network at 192.168.100.203. I have created the ACLs, class maps, and policy maps on all of the equipment.
For the remote buildings I have the following:
ACL
===========
Extended IP access list VOIP
permit tcp any host 192.168.100.203 dscp ef
permit tcp any host 192.168.100.203 eq 5566
[Code]....
I have put a hub in to capture traffic via Wireshark to see if DSCP flags are being appropriately marked and I do see that all VoiP packets are getting marked with as EF. However, I have been receiving phone calls from people in the remote buildings stating that their phones will cut out, flash Insufficient Bandwidth on the LCD displays and then the call will cut back in. I am wondering if the 2801 is not applying QoS with the rate-limits in mind since it is set to 100 Mb, or is it an issue with trying to take 3 remote locations and bring them down into 1 port on the 2801?
I have a strange problem with one switch in my LMS 3.2.1 installation.It is a WS-C3560-48TS with IOS 12.2(50)SE3 running. I have nine switches with the same type and IOS running without problems.
I notice the problem because there were no UT data for that switch. In RME and CS it was managed.Checking SNMP and config of the switch, but can't find any issues.Because at this time LMS ran in version 3.2 I installed at first CM 5.2.1 and after that the patches for CSCtd49439 and CSCtg20882.Next step was RME 4.3.1 with a lot of patches for different issues. Then I installed the patch for the internal error of CS (CSCtd07131).And finally I installed LMS 3.2.1 and patch for CSCto46927.Last step was installing the latest device packages. I did this directly from the application because it is much better handling than do a manual download. No the system seems to be fully updated.
I had the hope that CM will now find and manage this one switch. But it is still not available.I can't find the device in the data collection. But I can find it in the "Include Devices From DCR", although I configured to fetch all devices from DCR automatically to CM. To manually include the device is not working, too.
P.S. I used that step-by-step update path because it worked on two other servers very well for me.
I am trying image distribution to a c3560 device but I always get the error message SWIM1164. In the documentation it says to copy the logs and open a TAC Case but I would like to do some troubleshooting myself before opening a case.
Some actions to be taken prior to opening a case?
[code]...