I am unable to login to switch c3560 through Hostname but able to login through IP address. when i am putting the command : login authentication telnetpwd
getting the below message:
AAA: Warning authentication list "telnetpwd" is not defined for LOGIN.
Cisco cannot login? Currently i cannot login to the two of my cisco 3560 with the password that i usually used to login. and it is strength to me that its Configuration register is 0xF.
[BEGIN] 10/4/2011 10:22:57 AMshoTC-NGN-C3560-1>show verTC-NGN-C3560-1>show version Cisco IOS Software, C3560 Software (C3560-IPSERVICES-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)Copyright (c) 1986-2007 by Cisco Systems, Inc.Compiled Thu 19-Jul-07 18:15 by nachenImage text-base: 0x00003000, data-base: 0x01300000
ROM: Bootstrap program is C3560 boot loaderBOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SEC, RELEASE SOFTWARE (fc4)
TC-NGN-C3560-1 uptime is 50 weeks, 6 days, 9 hours, 34 minutesSystem returned to ROM by power-onSystem image file is "flash:c3560-ipservices-mz.122-35.SE5/c3560-ipservices-mz.122-35.SE5.bin"
[code]....
Is it possible to reduce de recoveery time after an interface shutdown? Current interface configuration is as follows and it takes 1 second to recover from a shutdown. I need to decrease this time.(Cisco Catalyst C3560) [code]
View 1 Replies View RelatedI am upgrading the network equipment at my place of employment. We use Cisco C3560, 2960, 4506 and I was noticing that IOS 15.0.x is available. After doing some reading it appears that Cisco is going to a pay for the licensing functionality that you want. Do I need to purchase licenses to upgrade from IOS 12.X to 15.0.x to maintain functionality?
View 4 Replies View RelatedWe have a Cisco switch in each office and every now and then the port that has the D-Link Wireless AP (DAP-1522) connected to it goes to err-disable state. Actually sometimes even a regular port that has a cisco phone connected may also go to err-disable state (less often). So I have to telnet into the switch and issue shut and no shut command on that interface to get it back to life, then it works for a few days or weeks until it happens again. Any suitable configuraiton for that interface, that would prevent that from happening or a workaround ?
Here's the info:
Model: cisco WS-C3560-24PS and cisco WS-C3560-48PS
Image:c3560-ipbase-mz.122-35.SE5.bin
This is the log from one switch:
31w5d: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/2, putting Fa0/2 in err-disable state
31w5d: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 74e2.f592.f7f2 on port FastEthernet0/2.
31w5d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
And from another, which is almost the same:
5d10h: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/3, putting Fa0/3 in err-disable state
5d10h: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address d8a2.5e31.2cf6 on port FastEthernet0/3.
5d10h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down
5d10h: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Here's the configuration of fe interfaces (they are all alike):
interface FastEthernet0/2
description Voice & Data Combo Port
switchport access vlan 11
switchport mode access
switchport voice vlan 15
[code]....
I am able to access ASA via hostname but with IP address it does not work.Need to know what config i need to put so i am able to access it using IP by ssh and ASDM? ASA is 5520 version is 8
View 12 Replies View RelatedI am working on adding a mapping to our external address for our mail server - let's call it mail.example.com
I would like to be able to access mail.example.com internally for our user's smartphones - if they access our company WiFi they are not able to get mail using the mail.example.com as the server name in their phone setups. However, once they leave the office and use any other WiFi it works fine. Also, I am unable to ping that address from any internal device. I believe also this is the reason Exchange accounts do not work on our site to site VPN connections.
I have a ASA 5520 and work primarily in the ASDM 6.4 to do configurations in the main office and have 5510 in our site to site connections.
I have a network running some 20 switches, two controllers and many AP's. All the devices that should be able to connect to cisco network assistant can successfully. However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology.
As far as I can see the config is identically to all other similar switches in the network. I can telnet from a switch (management VLAN) to the switch in question. However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful. However I can ping/telnet to all other cisco device from this PC. The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.
sho run
Building configuration...
Current configuration : 7363 bytes
!
version 12.2
no service pad
service timestamps debug datetime localtime
[code]......
I have upgraded NCS 1.1.1.24 to PI 1.2 lately. The installation process completed successfully.But now i am not able to log in to the GUI anymore as root. After entering the password all I get is a blank site (undefined).I get the same result with all known browsers. Rebooting or restarting NCS does not change anything.
View 12 Replies View Relatedhow can i access the backup SUP from telnet/console while it's in the standby state?
View 3 Replies View RelatedIs it possible to enable login by http (web interface) to catalyst 4006 switch with WS-C4006 Software, Version NmpSW: 6.3(5) ?
View 21 Replies View Relatedi recently upgraded our Ciscoworks LMS from 4.0 to 4.1. after i installed the upgrade the admin login doesnt work, neither does any other account. i have tried resetting the password but it doesnt work.
View 3 Replies View RelatedI configured a new SG-200-08 with a static IP. I tried to save the configuration as the startup configuration. After 10 minutes, I restarted the switch. It didn't boot with the new configuration, and returned to the default .254 and default pw. Now I cannnot assign a new pw or get past the change the pw page. When I try to save a new pw, the switch reboots and prompts me to change from the default pw. I tried resetting the switch by depressing the reset button for a long time, but results are the same. LED indicators are green with a flashing green indicating the .254 address and a solid green on the port where the switch is connected to the computer. How can I reset the switch or get passed the change your pw page?
View 3 Replies View Relatedif we are unable to login into switch how can we identify at which port of switch loop is there ?
View 3 Replies View RelatedWe are unable to login at Cisco 6509 switch, due to username and password not working. We have tried to recover the password as per Cisco document, but that is also not working. This switch is our Primary Switch in our network.
View 8 Replies View RelatedI have not worked with ASDM in a while. I have a 5510, with asdm-645.bin in the flash. The device runs version 8.4(2). I can download ASDM from the http interface of the firewall from the management interface. But I can not log in. I have used blank username and password, no username and enable password, blank username with enable password and a few other permutations. I then tried to connect to the asdm interface from inside also. But I can not connect. Needless to say, I have enabled http, and updated the http access-list. The only logging I have enabled is buffered. Is there any configuration that I am missing? Shall I cut and past the config?
View 4 Replies View RelatedI have a WLC 3750 and use the web authentication method with the internal login-page. Now I would like to add a link to a PDF document which is supposed to be available before logging in. In other words: Clients connect to the W-LAN and get access to the login-page. They can download the PDF document (which has by the way a size of ca 10MB) from the login-page and after that they login to get access to the internet.
As far as I understood the manuals I won't be able to use the internal login-page because the size of a file is not allowed to be bigger than 1MB.So I thought about using the external authentication by using the webserver of my website. Unfortaunely the IP-Adress of my website doesn't work. Behind this IP-adress there's more than one website hosted. So I can't use my webserver either ...
Is there any other possibilty to add this PDF (size 10MB) on the login-page? Maybe I can add my website to a kind of a "pass through list" which is accessible even without authentication?
I am having two dc switches with FWSM modules installed. DC switch1 FWSM (Ver 3.2(12) is wokring as active and Secondary DC switch2 FWSM (ver 3.2.(12) is in standby mode.
From yesterday I am trying to login primary FWSM, It is accepting my username and credentials but prompting again for username please refer below
DXB-DC1>session slot 5 p 1The default escape character is Ctrl-^, then x.You can also type 'exit' at the remote prompt to end the sessionTrying 127.0.0.51 Open. [code]
I recently upgraded several of my systems to Windows 8 from XP. This, of course, included the update to IE10.Now, I cannot log into the router on my network via a Windows 8 system. It works fine if I use a Windows 7 laptop or an XP unit, but on Windows 8, when I go to the router's address, it prompts me for the Username and Password. It takes the password, and then immediately comes back and asks for it again. Another weirdness is that it won't exit when I choose cancel - only if I select the red X in the upper right corner of the authentication window.
View 5 Replies View RelatedThe computer that i am using which is on the LAN Setup. Also it is connected to the domain. Whenever i tried to log on to the computer it is giving me an error message that "The System could not log on the "Domain Name" either the connection is disconnected or the domain is no longer available" somting like that. When i remove the LAN Cable and if i enter the domain password, i can login to the computer. after i log on the computer if i connect the LAN Cable it is working fine. I can access the other computer which is connected to the same domain. Why the error message is poping up?
View 4 Replies View RelatedJust installed a new WRVS4400N router. wireless working. however refuses to let me log back via Ethernet cable in at URL given me 403 Forbidden, Access Denies, Management via WLAN is not allowed. Was able to reset and noe braodcasting unsecured "cisco b" signal, but no way to get into router and set up security. unsure what I have done.
View 1 Replies View RelatedI'm unable to login Switch.......getting following error...I have tried this commands on other 3560 that worked...when I enter user name & password re logging authentication failed error occurs .........This is remote site Switch.
[code]...
When i tried to login through ASDM at Cisco ASA 5510, it ask for the username and password and after that nothing comes up. I am able to login through ssh. [code]
As per my knowledge show bootvar and show version, should shows the same IOS version. But here it's showing different. Is asdm-523 is compatible with IOS asa708.
We have a site where uses are unable to login to an application. After running a packet trace on the traffic coming from the site to the server they are trying to access, the trace indentifies that the client pc is sending a window size of zero to the server, and it does this twice. So in essence the client is saying it is too busy. This is strange as all the other applications work for the users and it is only this one application that is experiencing issues. The only other issue is that there is some retransmitted traffic before the client sends window size.
View 2 Replies View RelatedI can not access my hotmail account through msn.com, nor can I login to msn messenger as before. I get error message as follows:The requested URL /login.srf was not found on this server.Apache/2.0.59 (Unix) DAV/2 PHP/4.4.5 Server at [URL]Port 80
View 1 Replies View Relatedwhen I try to connect to a network where is required a login in the first webpage I cannot have internet access, but only local access.I mean: even for free internet connection, sometimes they require you to connect to their network, then open the browser that is automatically direct to their network login page in order to login in that page.my problem is that I am able to connect to the network but when i open any browser, it does not direct me to the login webpage; it tries to go to my homepage but, obviously, the computer is not still connected to internet, so on the browser it appear "Atheros AR5B91 Wireless Network Adapter".
View 5 Replies View RelatedBasically all I want to do is login to my routers config page so that I can forward ports. I was able to this a few weeks ago but recently I have received this error. Failed to connect
Things that I have already tried:
- Tries using 192.168.0.1, 192.168.1.1, http://192.168.1.1 and all kind of variations.
- Tried with different browsers.
- Tried with seperate computer with different OS's (Mac and PC)
- Unable to flush dns because I get this error: CMD prompt error message .
- Have factory reset router a few times now.
- Unplugged, left off for 20mins-2hours.
i cant login to my belkin f7d2301 v1 router tried fac reset
View 1 Replies View RelatedI just moved and have a new laptop, Comcast came in to reset the cable and internet. A new router was given to us and I cannot seem to access the password. I reset the router and now where to go nest since I try using the IP address and it is not recognizing it. I am using an unsecured WIFI access and I am not comfortable doing so.
View 1 Replies View Relatedchanged the router wan access pwd and now trying to test the dap i can't seem to log in with the default ip / dlinkap url access i have tried the bridge and ap switch setting on the dap with no luck after resetting the dap a couple of times with no luck ..
View 8 Replies View RelatedI configured the below config in Routers it is working good , but when i do the same in SWITCH-2960 , i am getting a problem not able to login to enable mode ... i am getting the basic login only ....
Error msg : % Error in Authentication.
Need to be configured at TAFE Network Devices: Code...
I try to login to my router http://192.168.1.1/ I try and put in the user name and password that I think it is. Is it the user name and password you set up or one that's already there and if so where can I find it??
View 6 Replies View RelatedI am unable to login to my router ? I have tried to reset my router and am still unable to login to the online control panel. The steps that I went about resetting the router were pushing the reset button for 30 seconds. That did not work so I pushed the reset button for 30 seconds, unplugged the router while continuing to hold the reset button for 30 seconds, plugged the router back in while holding the reset for 30 seconds.
View 6 Replies View Related