Windows 8 And IE 10 - Unable To Use Linksys Login?
Jan 28, 2013
I recently upgraded several of my systems to Windows 8 from XP. This, of course, included the update to IE10.Now, I cannot log into the router on my network via a Windows 8 system. It works fine if I use a Windows 7 laptop or an XP unit, but on Windows 8, when I go to the router's address, it prompts me for the Username and Password. It takes the password, and then immediately comes back and asks for it again. Another weirdness is that it won't exit when I choose cancel - only if I select the red X in the upper right corner of the authentication window.
View 5 Replies
ADVERTISEMENT
Jan 21, 2013
I am unable to login to my router ? I have tried to reset my router and am still unable to login to the online control panel. The steps that I went about resetting the router were pushing the reset button for 30 seconds. That did not work so I pushed the reset button for 30 seconds, unplugged the router while continuing to hold the reset button for 30 seconds, plugged the router back in while holding the reset for 30 seconds.
View 6 Replies
View Related
Jul 13, 2012
I'm having wrt610n and there is an issue, i can login to the config page via http, but using the same computer i'm not able to login there via https but the same time i can login via ipad and the other computer, using the https.i even tried to reset the router settings, but the result was the same, so what PC option can cause it?
View 6 Replies
View Related
May 9, 2013
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies
View Related
Dec 3, 2011
if we are unable to login into switch how can we identify at which port of switch loop is there ?
View 3 Replies
View Related
Feb 2, 2012
The computer that i am using which is on the LAN Setup. Also it is connected to the domain. Whenever i tried to log on to the computer it is giving me an error message that "The System could not log on the "Domain Name" either the connection is disconnected or the domain is no longer available" somting like that. When i remove the LAN Cable and if i enter the domain password, i can login to the computer. after i log on the computer if i connect the LAN Cable it is working fine. I can access the other computer which is connected to the same domain. Why the error message is poping up?
View 4 Replies
View Related
Dec 5, 2011
i recently upgraded our Ciscoworks LMS from 4.0 to 4.1. after i installed the upgrade the admin login doesnt work, neither does any other account. i have tried resetting the password but it doesnt work.
View 3 Replies
View Related
Apr 10, 2012
I configured a new SG-200-08 with a static IP. I tried to save the configuration as the startup configuration. After 10 minutes, I restarted the switch. It didn't boot with the new configuration, and returned to the default .254 and default pw. Now I cannnot assign a new pw or get past the change the pw page. When I try to save a new pw, the switch reboots and prompts me to change from the default pw. I tried resetting the switch by depressing the reset button for a long time, but results are the same. LED indicators are green with a flashing green indicating the .254 address and a solid green on the port where the switch is connected to the computer. How can I reset the switch or get passed the change your pw page?
View 3 Replies
View Related
Oct 29, 2011
I'm having trouble connecting wirelessly with my hp pavilion laptop, running on Windows 7. I just moved and am using a new modem and linksys router. I know the router works fine because my pc (also windows 7) connects just fine. Also, when I take my laptop to a different wireless network, (i.e. coffee shop, library, etc.) it works fine. I am able to get an ethernet connection, just not wirelessly. Windows diagnostics gets me nowhere.
View 4 Replies
View Related
Dec 11, 2011
We have a site where uses are unable to login to an application. After running a packet trace on the traffic coming from the site to the server they are trying to access, the trace indentifies that the client pc is sending a window size of zero to the server, and it does this twice. So in essence the client is saying it is too busy. This is strange as all the other applications work for the users and it is only this one application that is experiencing issues. The only other issue is that there is some retransmitted traffic before the client sends window size.
View 2 Replies
View Related
Sep 3, 2011
I can not access my hotmail account through msn.com, nor can I login to msn messenger as before. I get error message as follows:The requested URL /login.srf was not found on this server.Apache/2.0.59 (Unix) DAV/2 PHP/4.4.5 Server at [URL]Port 80
View 1 Replies
View Related
Jun 15, 2011
when I try to connect to a network where is required a login in the first webpage I cannot have internet access, but only local access.I mean: even for free internet connection, sometimes they require you to connect to their network, then open the browser that is automatically direct to their network login page in order to login in that page.my problem is that I am able to connect to the network but when i open any browser, it does not direct me to the login webpage; it tries to go to my homepage but, obviously, the computer is not still connected to internet, so on the browser it appear "Atheros AR5B91 Wireless Network Adapter".
View 5 Replies
View Related
Feb 4, 2013
Basically all I want to do is login to my routers config page so that I can forward ports. I was able to this a few weeks ago but recently I have received this error. Failed to connect
Things that I have already tried:
- Tries using 192.168.0.1, 192.168.1.1, http://192.168.1.1 and all kind of variations.
- Tried with different browsers.
- Tried with seperate computer with different OS's (Mac and PC)
- Unable to flush dns because I get this error: CMD prompt error message .
- Have factory reset router a few times now.
- Unplugged, left off for 20mins-2hours.
View 16 Replies
View Related
Mar 23, 2011
i cant login to my belkin f7d2301 v1 router tried fac reset
View 1 Replies
View Related
Apr 2, 2012
I just moved and have a new laptop, Comcast came in to reset the cable and internet. A new router was given to us and I cannot seem to access the password. I reset the router and now where to go nest since I try using the IP address and it is not recognizing it. I am using an unsecured WIFI access and I am not comfortable doing so.
View 1 Replies
View Related
Jan 5, 2012
changed the router wan access pwd and now trying to test the dap i can't seem to log in with the default ip / dlinkap url access i have tried the bridge and ap switch setting on the dap with no luck after resetting the dap a couple of times with no luck ..
View 8 Replies
View Related
Jul 4, 2011
We are unable to login at Cisco 6509 switch, due to username and password not working. We have tried to recover the password as per Cisco document, but that is also not working. This switch is our Primary Switch in our network.
View 8 Replies
View Related
Aug 23, 2011
I have not worked with ASDM in a while. I have a 5510, with asdm-645.bin in the flash. The device runs version 8.4(2). I can download ASDM from the http interface of the firewall from the management interface. But I can not log in. I have used blank username and password, no username and enable password, blank username with enable password and a few other permutations. I then tried to connect to the asdm interface from inside also. But I can not connect. Needless to say, I have enabled http, and updated the http access-list. The only logging I have enabled is buffered. Is there any configuration that I am missing? Shall I cut and past the config?
View 4 Replies
View Related
Jan 22, 2012
I have a WLC 3750 and use the web authentication method with the internal login-page. Now I would like to add a link to a PDF document which is supposed to be available before logging in. In other words: Clients connect to the W-LAN and get access to the login-page. They can download the PDF document (which has by the way a size of ca 10MB) from the login-page and after that they login to get access to the internet.
As far as I understood the manuals I won't be able to use the internal login-page because the size of a file is not allowed to be bigger than 1MB.So I thought about using the external authentication by using the webserver of my website. Unfortaunely the IP-Adress of my website doesn't work. Behind this IP-adress there's more than one website hosted. So I can't use my webserver either ...
Is there any other possibilty to add this PDF (size 10MB) on the login-page? Maybe I can add my website to a kind of a "pass through list" which is accessible even without authentication?
View 11 Replies
View Related
Apr 13, 2011
I am having two dc switches with FWSM modules installed. DC switch1 FWSM (Ver 3.2(12) is wokring as active and Secondary DC switch2 FWSM (ver 3.2.(12) is in standby mode.
From yesterday I am trying to login primary FWSM, It is accepting my username and credentials but prompting again for username please refer below
DXB-DC1>session slot 5 p 1The default escape character is Ctrl-^, then x.You can also type 'exit' at the remote prompt to end the sessionTrying 127.0.0.51 Open. [code]
View 1 Replies
View Related
May 9, 2011
I have hp-dv6 with ralink rt5390 and my router is cisco linksys WAG120N and I'm trying to connect to my wireless connection but after I put the password it gives me windows was unable to connect! however at my work they have router but not linksys and I can connect to it and surfing the internet , but I have no problem with my cisco linksys because I use many laptops to connect to it without problems so is there any Compatibility issue with ralink rt5390 and cisco linksys router?? by the way I have the latest driver 3.1.13.1 of ralink.
View 9 Replies
View Related
Jul 31, 2011
I try to login to my router http://192.168.1.1/ I try and put in the user name and password that I think it is. Is it the user name and password you set up or one that's already there and if so where can I find it??
View 6 Replies
View Related
Dec 29, 2012
Region : Canada
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
ISP : ShawCable
I have just bought the device. I works fine as a AP out of the box. I want to use it as a repeater of my wireless network which uses a Linksys Simultaneous Dual Band N Router WRT400N
1. To do the setup, I have tried to login at 192.168.0.254 I cannot do this (a) using a wireless connection to a Linksys router which is connected to the cable modem and (b) wired connection to the router which is connected to the cable modem. The attempts get a timeout messaage.
2. The default gateway is 192.168.1.1. The DHCP server has the same address. My computer is using 192.168.1.101.
3. I use McAfee Internet Security software.
View 1 Replies
View Related
Jul 4, 2012
I am unable to login to switch c3560 through Hostname but able to login through IP address. when i am putting the command : login authentication telnetpwd
getting the below message:
AAA: Warning authentication list "telnetpwd" is not defined for LOGIN.
View 5 Replies
View Related
Aug 9, 2012
Just installed a new WRVS4400N router. wireless working. however refuses to let me log back via Ethernet cable in at URL given me 403 Forbidden, Access Denies, Management via WLAN is not allowed. Was able to reset and noe braodcasting unsecured "cisco b" signal, but no way to get into router and set up security. unsure what I have done.
View 1 Replies
View Related
Jul 5, 2012
I'm unable to login Switch.......getting following error...I have tried this commands on other 3560 that worked...when I enter user name & password re logging authentication failed error occurs .........This is remote site Switch.
[code]...
View 7 Replies
View Related
Jul 6, 2011
When i tried to login through ASDM at Cisco ASA 5510, it ask for the username and password and after that nothing comes up. I am able to login through ssh. [code]
As per my knowledge show bootvar and show version, should shows the same IOS version. But here it's showing different. Is asdm-523 is compatible with IOS asa708.
View 6 Replies
View Related
May 28, 2011
I work from a remote location, and use a VPN to access files on the company server. I have no problem logging into the VPN, but when using Windows 7 64-bit, I am denied access to the specific folder containing the files I need, even though I can see and open other folders on the same server.
However, if I connect from an old laptop running Windows 2000, I get a login pop-up when I click on the desired folder and after entering my username (including the remote domain name) and password I can access the files. In the newer OS, I just get a stock "access denied" message, with no option to log in. Specifically, in W7 the message is "You do not have permission to access this folder", which is nonsense.
Our IT department is baffled. How to set up W7 so it will allow me to log into the protected folder in the same way I can do it in W2K? Once logged in to the VPN itself, I use the 'run' command with the remote IP address to bring up the folders in a normal Explorer window.
View 3 Replies
View Related
May 16, 2012
I want to limit the concurrent login my users can have. I have downloaded and installed Limit Login from Microsoft and followed the directions to a T. However, when users login it doesn't do anything. The scripts don't run (I have them listed in the logon and logoff scripts for users in the default domain policy). The scripts are stored in a share that everyone has read access to. What am I doing wrong? I have installed and uninstalled a million times following the MS directions included with the software to the letter, but it won't work. At one time I had it working and then we had some network problems with profiles and it got messed up in that process. Now I'm trying to get it back, but can't. Even uninstalling and reinstalling.
View 2 Replies
View Related
Oct 12, 2010
I purchased the AE1000 wireless adapter for use with my Linksys WRT54G router. I first tried to install by loading the CD, which went so far as the "Insert your adapter into a USB port" screen. The Windows "processing" circle spun for about twenty minutes, then I was prompted to "insert the wireless adapter" once more. Rinse, repeat. I absolutely cannot get past this step. I scoured the web for an answer and turned up little. I uninstalled my antivirus and firewall software, made certain that files associated with my prior adapter were removed, tried varying USB ports (all 2.0) on my desktop, and had no success. Today, I exchanged the adapter for a replacement, and I'm encountering all of the same difficulties.
View 6 Replies
View Related
Dec 30, 2012
I configured the below config in Routers it is working good , but when i do the same in SWITCH-2960 , i am getting a problem not able to login to enable mode ... i am getting the basic login only ....
Error msg : % Error in Authentication.
Need to be configured at TAFE Network Devices: Code...
View 4 Replies
View Related
Sep 3, 2011
I have 2 PC at home and would like to network them together so i could share the resources between them. But i could only manage to setup 'one way' - the XP Home could access the Windows 7 Ultimate but not the other way Whenever i double click on the XP Home, it will prompt me to login. But no matter what i enter, it will say its wrong. What weird is the 'domain'. The login dialog will show that im login into 'Domain: Windows7PC' when im trying to login into the XP. And after i have enter 'wrongly', it will show the username as 'Windows7PCusername' and ask to try again - it means im login into the Windows 7 And if i try to prefix the PC's name in front - \WindowsXPusername then it will prompt \WindowsXP is not accessible..... The specified username is invalid
Here is my 'settings'-
Windows 7 Ultimate SP1
Windows XP Home SP3
Both is on the same Workgroup/IPGroup/Netmask
Both has File & Printer Sharing Enabled
Have patch XP with KB922120v6
[code]....
View 14 Replies
View Related
Feb 22, 2012
I'm unable to access the web setup screen from 4 different windows machines running IE 9 or Firefox (various combinations of wireless, wired, etc.). When I get to the certificate error and hit the "yes, i understand, continue", it comes back with a 'can't be reached' page and looking into the details says the 'connection was dropped'. However If I connect from a MacBook / safari, I'm able to reach the page fine (and admin the router).
Using a wrt610n.I am connected to the router, the ip address hasn't changed, the password hasn't changed.I can use the router & connect to the internet.I have the router set to require HTTPS, but switching it to allow HTTP doesn't work. Both Wired & Wireless Win 7 / IE9 machines can't connect.Tried setting the router ip address to 'trusted' zone in IE. Tried setting the router ip address to the 'compatibility' mode in IE. Tried using latest version of Firefox with the same results.
View 3 Replies
View Related
