I have ASA 5512X and I'm trying to run CX features on it. but the problem is I don't have SSD drive in the chassis. how can I get one? is any kind of SSD drive compatible with cisco ASA-CX firewalls or i should order it from cisco only? what is the part number for that model?
View 3 Repliesi found this part number for asa5512x product "ASA5512-SSD120-K9" it's a New Product Hold and under group "Cisco ASA CX Context-Aware Security" Who have know more information about this? Cisco ASA CX Context-Aware Security ASA5512-SSD120-K9 ASA 5512-X with SW, 6GE Data, 1GE Mgmt, AC,3DES/AES,SSD 120G
View 3 Replies View RelatedWhat kind of DRAM memory compatible with 3845?
View 7 Replies View RelatedI just bought the Seagate FreeAgent GoFlex Home, 1TB network hard drive for my home network and I cannot put files on the hard drive. The hard drive is connected to my Apple Extreme Airport router, and I can see the hard drive when I go to network on my Windows 7 computer, but when I try to put something in/open it, it gives me "error code 0x80070035 The network path was not found." Im not sure if it is my router
View 1 Replies View RelatedI have a customer with active/standby on a pair of 5510's with the CSC modules. They were inquiring about the AIP/ASA, and since this would NOT work in their current setup, would getting a pair of 5510/AIP configured for transparent failover work placed in front fo the existing units? Would I need to have a switch placed between the AIP and CSC ASA's? Or would I setup the ASA's for context based Active/Active failover to interconnect the ASA's to the existing units, but I still see a need for a switch.
View 1 Replies View RelatedWe are in the middle of upgrading from two PIX's to some new ASA5512X's. To give you some background on the situation we are upgrading these since the PIXs are fairly old. We had one extra that we had to use since one PIX has failed already. The guy that implemented the PIXs orginally was learning how to do so as he went so there is alot of needless config in the PIX, atleast from what I can tell. Another guy that works with me has done some configuration on the new ASAs and has done the majority of it so far. Today we went to install the new ASAs and switch everything over hoping it would work, but that didn't happen. It seems that there is something wrong with our NAT and ACLs somewhere along the lines. The way our network is laid out is that we have two school campus with a site-to-site VPN one is 172.17.0.0/16 and the other is 172.18.0.0/16. We also have a remote-access VPN on both ASA's. When we connected the new ASAs up and brought up the interfaces, nothing on the inside could ping the internet nor the other side. The VPN showed active on the ASA's and each ASA could ping the others outside interface, but that was it. I have posted the configs below.
ASA1:
: Saved
: Written by enable_15 at 04:26:18.240 CDT Tue Mar 12 2013
!
ASA Version 8.6(1)2
[Code].....
I am updating my 8.2(3) code for my new ASA5512 that is running 8.6(1) and am unable to get on the internet with my current configuration from the inside interface.
Information:
Outside: ***.***.33.11
Gateway: ***.***.32.9
Inside: 192.168.215.0 /24
dhcp 215.100 - 150
[Code] .....
I need to know if the 5512X IPS will work if the ASA is in transparent mode and/or any limitations.
View 5 Replies View RelatedTrying to setup a new ASA 5512 and like a ******* I've somehow locked myself out.
how to do a hardware reset?
I just bought an E4200 hoping to plug my external hard drive in. Unfortunately, the drive isn't even showing up as connected. I'm using an Icy Box enclosure around a toshiba laptop drive right now.
View 4 Replies View RelatedWith Norton 360 Antivirus, is there a feature that allows you to make it clear your hard drive of all unnecessary files that are slowing down the CPU? (similar to what the technicians for dell do when you call, they delete everything unnecessary) I've done the temporary file removal and it didn't do much, along with the full system scan. If Norton can't do this, is there any way to make a software go through the hard drive and delete all the crap?
View 5 Replies View Relatedi have asa 5520 configured as VPN Gateway to terminate remote access vpn , i have question , how can i restrict the access to only 1 range of public source IPs to access my corporate via RA ,is this possible?if so how to configure it?
View 1 Replies View RelatedRecently upgraded to an Asa 5512x from a pix 515e. I have an Ipswitch secure MoveIT server on the dmz1 interface that needs to be accessed from both the inside and outside interfaces. I have setup a static nat from the outside to the dmz1 and it works, I can also connect from the inside interface. Now I need the MoveIT server to access the DNS server and email server on the inside interface so it can send notifications. On the pix I just created a static from the inside to the dmz1 using its own IP address - static (inside,dmz1) 192.168.1.7 192.168.1.7 net mask 255.255.255.255. I would then add the access-list to allow. How would I set this up with the Asa 8.6 commands?
View 5 Replies View RelatedI'm trying to get started on setting up my first Transparent ASA.I understand an ASA in Transparent Mode can now have an ip address with Bridge Groups or some such mechanism. I'm looking for examples of how to set that up and other information below. Is the ip address associated with the device or is it interface specific? Will I be able to SSH with that ip address setup? Can I use ASDM if the Transparent ASA has an ip address? This 5512X has an IPS. Any one who has setup an IPS on this platform knows it has some very particular requirments in order to communicate with the outside world. I need examples of how to do that with a Transparent ASA.How is NAT setup differently (if at all) on a Transparent ASA?Are ACLs done any differently?
View 3 Replies View RelatedI was wondering how to tighten the security of my email delivery to a range of ip addresses (I know how on my old firewall but the cisco is quite a bit different). Right now anyone sending email to a particular ip address on my firewall can do so. I want to restrict that to two ip address ranges it will accept deliver from. I'm thinking I need two network objects for the two ranges then add to a network object group. Configuring the ACL for delivery using that group if I'm correct about that ?
View 4 Replies View Relatedurl...For the New Firewalls i.e. 5512X , 5515X etc there seems to be integrated IPS and we don't need to order any extra license or part number to get the IPS features .
But for the 5585X It says 2Gbps for SSP10 engine but I have seen in the Dynamic Configuration Tool that SSP10 and IPS-SSP10 are different things . Which means that I will have to order 2 service engines SSP10 and IPS SSP10 to get the IPS features and if I only order SSP10 with that Chasis I will only get firewalling ?
I am trying to figure out if the new code for ASA SM 9.0(x) or 9.1 is compatible with CAT6500 but I could not find any document that explicity confirms the the INCOMPATIBILITY. This table from the Release notes is not quite clear.
[URL]
It says that code 8.5 is compatible with Cat6500 and version 9.X is compatible with R7600.So are the two different trains now, one for Cat6500 and one for R7600?
My real goal is to find the correct software versions (not interim) that provides compatilibity with Catalyst 6500 with Supervisor 2T and ASASM.
i want to acces the video content of the Dutch television channels, but i am living abroad, they track the ip, see i am not in holland and dont show the content. There are some companies providing a vpn subscription in the Nethderlands for 15 Euro a month and that works perfect, just its a little expensive. Now my hope was to buy a seccond hand vpn router, that i want to put at my parents place in holland, and some how use it in the same way as the vpn service of the company. So using it to connect, and browsing trough this connection to get a Dutch ip.
View 2 Replies View RelatedI am looking into a DR plan where should a primary site go down users with the Cisco anyconnect client will be able to VPN to a second site. The ASA I am configuring is a 5512x for the 2nd site. The main site has a pair of 5510's in a HA pair. Is it possible to setup a secondary Remote Access VPN connection for users to connect to? If I was to configure Anyconnect RA VPN on the ASA on the 2nd I would need to purchase an SSL cert in order to configure this?
View 9 Replies View RelatedI was under the impression that those global addresses that we used with NAT were from the outside IP addresses range?Lets say my outside IP address is idk 192.112.40.11 /30 and I only had two usable IPs (since you can't use network and broadcast IPs) so how would I set up NAT for a couple of Inside addresses with a shorting of addresses like this? Idk if that makes sense what I'm trying to say
View 3 Replies View RelatedWe have a configuration where we go through a firewall (ASA 5510) to a router, which decides if it is internet traffic or another network used for colleges etc in Canada called SR Net. If it is internet traffic it then goes through another ASA 5510 to the internet.
When we tested we were not seeing the speed of our internet (about 1/10th). We tested by putting the laptop before the internet firewall and we get the throughput. We also threw the test laptop before the router and we got the throughput expected. But when the test laptop is before the internal (first) firewall we get about 1/10th the speed. We are Nating on both firewalls, so from the inside we are going from a private IP to a Public IP (so it can go to SR Net is need be), then Nating again to the internet IP on the second firewall.
We have currently install single ASA 5550 and want to install one more ASA for active standby mode, but cisco discontinue or End of sale ASA 5550. can any one guide me ASA 5555X is compatible with ASA5550 on active standby mode or not.
View 2 Replies View Relatedwe have a pix 515E firewall with software version Cisco PIX Security Appliance Software Version 7.0(4) and ASDM version Device Manager Version 5.0(4). we are in a process of upgrading the software. Kindly suggest the software and ASDM version most fit for the device. Also the software should be compatilbe for the current configuation running.
View 3 Replies View RelatedI'm not sure how I turn off my firewall
View 4 Replies View RelatedI am currently working on our Cisco voice platform at work.
Our Cisco firewall engineer has left and I have been given the task of looking after the firewalls as our Chief Exec seems to think that Cisco Voice is similar to Cisco ASA firewalls,
Are there any books/videos out that you can recommend to learn the about firewalls quickly.
I have two firewalls in 2 different locations. They act as primary and secondary for my WAN connectivity. I would want a way to synchronize access-lists in both without manually replicating.(access list, NAT and Route)FW model cisco 5580
View 1 Replies View RelatedI am trying think of a better way to provide redundancy on some internally protected networks. We maintain our own WAN/backbone between our primary site and backup site. Is it possible to have two Cisco ASA 5550s in setup for failover at completely different sites as long the networks connected are available?
View 3 Replies View RelatedWe currently have redundant FWSM's and are planning a migration to standalone ASA 5500 series firewalls. However, we have a complete VMWare environment and are looking at the Nexus 1000V. I understand the Nexus 1000V and VSG architecture and implementation, and I do understand that the ASA 1000V is designed for cloud environments. But I do have one question about the ASA 1000V.
Is it possible for an ASA 5500 series firewall to be replaced by an ASA 1000V? Basically, can an ASA 1000V be a sole firewall solution, or are ASA 5500's still needed? Is there a datasheet anywhere that compares the ASA 1000V and ASA 5500 series?
I've been trying to open ports 5800 and 5900 for UltraVNC and checking them with online port checkers, but they are always listed as closed. I've even tried taking town windows firewall, my router firewall (although as soon as I disable and apply, it automatically switches back to enabled again), and also DMZ'ing my router. I wonder if it might have something to do with my new modem, but in the config page for that, the advanced settings are locked out. the modem is an arris TM722G, and the router is a linksys wrt-54G with DDWRT firmware.
I'm running windows 7 x64 and using a static local IP, I want to be able to use DynDNS to connect to UltraVNC.
According to documentation Cisco RPS 675 should have support for Cisco 3750v2 switch(WS-C3750V2-48PS).What kind of cable should be used to connect them?Cisco RPS has 16 pins and 3750v2 has 22 pins.I could not find that type of cable,
View 2 Replies View RelatedWe are planning to install a new SSM-4GE module on both Active and Standby firewalls. how can we install an new SSM-4GE with a minimum outage. I was planning to install the module in the following steps.
1. Power off the secondary firewall(FW02).
2. Install a new module.
3. Power up the secondary firewall
4. Power off the primary firewall(FW01)---> in this step will the secondat firewall become active as there is a hardware conflict.
5. Install a new module.
6. Power up the Primary firewall(FW01)
or do i need to power down both the firewalls and then install the modules?i have is that after the installation only one port on the new SSM-4GE module would be in use on Primary firewall(FW01) which is a terminating link from a router. No link would be terminating on the new SSM-4GE module on secondary firewall. Will the firewalls still fail over in this case or does it require a link going to the secondary firewall on new SSM-4GE module(same port as on primary firewall) from the router.
I have a 5510 ASA and have been given another an told to make them active and standby. Basically the active one is working great but the second one has no config on it apart from the default one, but is the same firmware level. I guess I need a crossover cable, and what happens with the inside and outside interfaces, would they need to go into a vlan on a switch, one inside vlan where the 2 firewalls inside interface go into and another vlan for the outside? Otherwise if it failsover to the standby ASA the inside and outside interfaces wouldn't work.
View 4 Replies View RelatedWhat device would be necessary to link two networks of identical type? What devices would be necessary to link two networks of dissimilar types?I would say a network card and HUB for identical type but I do not know if this is correct?Describe the parameters governing the choice of cable type for a given network. What are the three main types of cables used in computer networks?
View 3 Replies View Related