Cisco Firewall :: 5512x - Static Translation From DMZ To Inside On ASA 8.6
Dec 20, 2012
Recently upgraded to an Asa 5512x from a pix 515e. I have an Ipswitch secure MoveIT server on the dmz1 interface that needs to be accessed from both the inside and outside interfaces. I have setup a static nat from the outside to the dmz1 and it works, I can also connect from the inside interface. Now I need the MoveIT server to access the DNS server and email server on the inside interface so it can send notifications. On the pix I just created a static from the inside to the dmz1 using its own IP address - static (inside,dmz1) 192.168.1.7 192.168.1.7 net mask 255.255.255.255. I would then add the access-list to allow. How would I set this up with the Asa 8.6 commands?
View 5 Replies
ADVERTISEMENT
Jan 10, 2013
I have seen many of these errors lately. We have just moved to a new office and I have basically only assigned a new IP to the outside interface.
[code]....
View 6 Replies
View Related
Mar 24, 2013
We have an ASA 5540 with 8.2(5)
Last three days in early afternoon we start getting these errors in the log and webpages either won't load or pages only half load.
3|Mar 22 2013|13:22:24|305006|184.73.105.115|443|||portmap translation creation failed for tcp src inside:10.10.176.114/58217 dst outside:184.73.105.115/443
3|Mar 22 2013|13:22:24|305006|54.243.129.71|80|||portmap translation creation failed for tcp src inside:10.35.54.37/1517 dst outside:54.243.129.71/80
[Code].....
View 6 Replies
View Related
May 30, 2011
I'm trying to migrate from olda PIX to newest ASA 8.4.1. Everything seems to be good except the static NAT. [code]
The inside interface uses implicit rule. ( permit any less secure network )
Although te above config the ASA logs the following.
TCP access denied by ACL from 94.94.94.94/2003 to outside:86.101.228.221/80
The 86.101.228.221 our public Internet IP whic are used as outside IP also.
View 8 Replies
View Related
Aug 22, 2011
I have an 8.3(2) ASA with a single outside IP. Dynamic PAT translates inside addresses to the outside interface address. I would like to use static NAT with port translation to access an inside syslog server. I got an error when I tried using the outside interface address. Can I use both dynamic PAT and Port Translation with the same outside address?This is what I would like to use but I receive an error saying there is an overlap using the outside interface address.(192.168.1.0 is my inside network. 10.10.1.10 is the outside interface IP.)
object network inside-net
subnet 192.168.1.0 255.255.255.0
nat (inside, outside) dynamic interface
object network SYSLOG_SERVER
host 192.168.1.50
nat (inside,outside) static 10.10.1.10 service tcp ssh ssh
View 6 Replies
View Related
Mar 29, 2011
I have inherited an ASA 5520. In doing some auditing of the setup, I have noticed a Static Route that has the inside interface of the ASA as the Gateway IP. I am trying to understand the purpose of this route or why a route would be setup this way.
Example Static Route:
Inside 10.xx.31.0 255.255.255.0 10.xx.xx.10 (10.xx.xx.10 is the inside interface of ASA)
View 2 Replies
View Related
May 10, 2012
customer has a server which located in inside interace. and an outside interface connected to ISPA. cu config a static nat map inside server address to ISPA address, one day customer install a new outside interface to ISPB, cu config new static nat ,map same server inside server address to ISPB address. the server will allways be vistited from outside interface and reply, custome want traffic coming from ISPA will return to ISPA, traffic coming from ISPB will return to ISPB. but i found it is difficult implement this on ASA5580. i want use route-map on static nat, but it will not satisfy customer's request.
View 3 Replies
View Related
Jul 13, 2011
i have a problem customer has a server which located in inside interace. and an outside interface connected to ISPA. cu config a static nat map inside server address to ISPA address one day customer install a new outside interface to ISPB, cu config new static nat ,map same server inside server address to ISPB address. the server will allways be vistited from outside interface and reply, custome want traffic coming from ISPA will return to ISPA, traffic coming from ISPB will return to ISPB. but i found it is difficult implement this on ASA5580. i want use route-map on static nat, but it will not satisfy customer's request.
View 6 Replies
View Related
Oct 16, 2011
I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
object network obj-10.1.1.254
host 10.1.1.254
object network obj-10.1.1.254
nat (inside,outside) static 172.25.10.3
I want to also use nat (inside,backup) static 172.25.10.3
View 3 Replies
View Related
Dec 6, 2010
I have a nat and vpn setup on my Cisco 2801 router.Everything is working as expected except the NAT. I have a single static nat translation but it only works for inbound and not outbound. Going outbound, it uses the default overload nat address of the outside interface. [code] I want to add another mailserver. But I fear if one mailserver were to get black-listed, they would both be reporting there ip address as the same address (the one on the ethernet interface) which would blacklist both mail servers.Again, inbound nat works ok, but outbound is just using the IP of the ethernet0/0 address.
View 2 Replies
View Related
Jul 19, 2011
I am trying to change a static nat entry from this:
ip nat inside source list 1 interface Dialer0 overloadip nat inside source static tcp 192.168.0.246 25 interface Dialer0 25ip nat inside source static tcp 192.168.0.246 80 interface Dialer0 80ip nat inside source static tcp 192.168.0.246 443 interface Dialer0 443
to
ip nat inside source list 1 interface Dialer0 overloadip nat inside source static tcp 192.168.0.247 25 interface Dialer0 25ip nat inside source static tcp 192.168.0.247 80 interface Dialer0 80ip nat inside source static tcp 192.168.0.247 443 interface Dialer0 443
I have tried various methods from exec mode clear ip nat translation *
no ip nat inside source static tcp 192.168.0.246 443 interface dialer0 443 But I am getting cisco2800(config)#%Static entry in use, cannot remove.
View 2 Replies
View Related
Mar 24, 2011
In my router I can set rule that all traffic incoming to router's extAddr:8888, is forwarded to my intAddr:8888. But I also need reverse rule that packets originating from intAddr:8888 are translated to extAddr:8888. Can I do that? What technique can I search on google to find more information, because it is not port forwarding. I would calll it reverse port forwarding or static port address translation, but I do not find anything useful in internet searching these keywords.
View 3 Replies
View Related
Mar 12, 2013
We are in the middle of upgrading from two PIX's to some new ASA5512X's. To give you some background on the situation we are upgrading these since the PIXs are fairly old. We had one extra that we had to use since one PIX has failed already. The guy that implemented the PIXs orginally was learning how to do so as he went so there is alot of needless config in the PIX, atleast from what I can tell. Another guy that works with me has done some configuration on the new ASAs and has done the majority of it so far. Today we went to install the new ASAs and switch everything over hoping it would work, but that didn't happen. It seems that there is something wrong with our NAT and ACLs somewhere along the lines. The way our network is laid out is that we have two school campus with a site-to-site VPN one is 172.17.0.0/16 and the other is 172.18.0.0/16. We also have a remote-access VPN on both ASA's. When we connected the new ASAs up and brought up the interfaces, nothing on the inside could ping the internet nor the other side. The VPN showed active on the ASA's and each ASA could ping the others outside interface, but that was it. I have posted the configs below.
ASA1:
: Saved
: Written by enable_15 at 04:26:18.240 CDT Tue Mar 12 2013
!
ASA Version 8.6(1)2
[Code].....
View 5 Replies
View Related
Jul 8, 2012
I am updating my 8.2(3) code for my new ASA5512 that is running 8.6(1) and am unable to get on the internet with my current configuration from the inside interface.
Information:
Outside: ***.***.33.11
Gateway: ***.***.32.9
Inside: 192.168.215.0 /24
dhcp 215.100 - 150
[Code] .....
View 6 Replies
View Related
Dec 19, 2012
I need to know if the 5512X IPS will work if the ASA is in transparent mode and/or any limitations.
View 5 Replies
View Related
Aug 5, 2012
Trying to setup a new ASA 5512 and like a ******* I've somehow locked myself out.
how to do a hardware reset?
View 5 Replies
View Related
Jan 6, 2013
i found this part number for asa5512x product "ASA5512-SSD120-K9" it's a New Product Hold and under group "Cisco ASA CX Context-Aware Security" Who have know more information about this? Cisco ASA CX Context-Aware Security ASA5512-SSD120-K9 ASA 5512-X with SW, 6GE Data, 1GE Mgmt, AC,3DES/AES,SSD 120G
View 3 Replies
View Related
Jan 21, 2013
I'm trying to get started on setting up my first Transparent ASA.I understand an ASA in Transparent Mode can now have an ip address with Bridge Groups or some such mechanism. I'm looking for examples of how to set that up and other information below. Is the ip address associated with the device or is it interface specific? Will I be able to SSH with that ip address setup? Can I use ASDM if the Transparent ASA has an ip address? This 5512X has an IPS. Any one who has setup an IPS on this platform knows it has some very particular requirments in order to communicate with the outside world. I need examples of how to do that with a Transparent ASA.How is NAT setup differently (if at all) on a Transparent ASA?Are ACLs done any differently?
View 3 Replies
View Related
Apr 28, 2013
I have ASA 5512X and I'm trying to run CX features on it. but the problem is I don't have SSD drive in the chassis. how can I get one? is any kind of SSD drive compatible with cisco ASA-CX firewalls or i should order it from cisco only? what is the part number for that model?
View 3 Replies
View Related
Feb 2, 2013
I was wondering how to tighten the security of my email delivery to a range of ip addresses (I know how on my old firewall but the cisco is quite a bit different). Right now anyone sending email to a particular ip address on my firewall can do so. I want to restrict that to two ip address ranges it will accept deliver from. I'm thinking I need two network objects for the two ranges then add to a network object group. Configuring the ACL for delivery using that group if I'm correct about that ?
View 4 Replies
View Related
Apr 30, 2012
url...For the New Firewalls i.e. 5512X , 5515X etc there seems to be integrated IPS and we don't need to order any extra license or part number to get the IPS features .
But for the 5585X It says 2Gbps for SSP10 engine but I have seen in the Dynamic Configuration Tool that SSP10 and IPS-SSP10 are different things . Which means that I will have to order 2 service engines SSP10 and IPS SSP10 to get the IPS features and if I only order SSP10 with that Chasis I will only get firewalling ?
View 3 Replies
View Related
May 6, 2012
I need to open a port in a Cisco 2911 router to permit the conexion to an equipment that is inside the LAN, but I my configuration doesn't workt.
I have 3 interfaces configured: two WAN interfaces (one is a backup of the other) and a LAN interface. The configuration is this (public IPs are changed):
track 1 ip sla 1 reachability
!
!
interface GigabitEthernet0/0
description backup
ip address 176.55.25.25 255.255.255.252
ip nat outside(code )
View 16 Replies
View Related
Jul 30, 2012
We have two sites: 192.168.100.x and 192.168.101.x currently connected via IPsec VPN. On each end we have a Cisco ASA 5505. However, each site also has an MPLS VPN with intentions to move all traffic to this link. Will this work on the ASA? We need to make sure traffic can hit the ASA @ site A on the inside interface and trafiic will forward to the MPLS VPN router which then handles the traffic. Too, will it cause any problems in bi-directional flow between the two sites?
View 3 Replies
View Related
Aug 24, 2012
I am going with ASA 5520, know how many NAT translation is possible.
View 2 Replies
View Related
Jan 21, 2013
Platform:
cisco6509-E with FWSM
Supervisor Engine 32 PISA 8GE
sup-bootdisk:s32p3-adventerprisek9_wan-mz.122-18.ZY2.bin
command:
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
(config)#no ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
#clear ip nat tran *
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
%Port 14029 is being used by system
Or %Static entry in use, cannot change
But when I perform "sh ip nat tran" command,There is nothing
View 1 Replies
View Related
Mar 1, 2012
I have some issues with Twin PAT on ASA (8.4.2), there is sth I dont udnerstand FTP server is on the inside and client is in outside.
I did sth like this
object network NATED-11
host 20.20.20.11
object network REAL-2
host 10.200.200.2
object service SRV-FTP
service tcp destination eq ftp
nat (outside,inside) source static any any destination static NATED-11 REAL-2 service SRV-FTP SRV-FTP so teoretically there should be a problem in NAT cause there is a second channel for data etc. BUT according to docs "For applications that require application inspection for secondary channels (for example, FTP and VoIP),the ASA automatically translates the secondary ports."
The problem is that it doesn't work at all and got the syslogs
Debug on ASA shows
ASA5510(config)# nat: untranslation - outside:20.20.20.11/21 to inside:10.200.200.2/21
nat: untranslation - outside:20.20.20.11/21 to inside:10.200.200.2/21
nat: untranslation - outside:20.20.20.11/21 to inside:10.200.200.2/21
nat: translation - outside:20.20.20.252/37924 failed - port is not found in xlate(0-0)
[code]....
To make it work I need to modify the nat rule to sth like this (translate source of client to inside inteface of ASA) nat (outside,inside) 1 source static any interface destination static NATED-11 REAL-2 service SRV-FTP SRV-FTP / why its not working in the first place? aaa I forgot to mention that both modes of FTP were tested (passive and active)
View 1 Replies
View Related
Dec 5, 2012
I have a server in a DMZ of my 8.4 ASA with nat:
object network FTP-SERVER
host 192.168.1.102
nat (dmz,outside) static interface tcp ftp ftp
And that's working well. However, I now need to translate the source address of connections from the outside to the FTP server as well. The aim is that the source address of packets when they reach the FTP server is an address on the DMZ subnet (as the default route for the FTP server now needs to be something else, not the ASA) as well as this outside-dmz NAT. I thought overloading the DMZ interface of the ASA? Or another IP in that range?
View 2 Replies
View Related
Mar 10, 2012
Trying to translate telnet for switches to the outside ip address at some random ports.
172.16.200.2:23 -> 10.199.199.2:2300
172.16.200.3:23 -> 10.199.199.2:2301
172.16.200.4:23 -> 10.199.199.2:2302
etc....
ASA 5510 running 8.4(3):
interface Ethernet0/0
nameif outside
security-level 0
ip address 10.199.199.2 255.255.255.248
interface Ethernet0/1.200
vlan 200
nameif inside
security-level 100
ip address 172.16.200.254 255.255.255.0
[code]....
I can not access the switch at 10.199.199.2:2301 . What am I doing wrong? Or should cleaning toilets be something I really should look at! Now if i run this NAT statment:
object network Switch_TN
nat (inside,outside) static 10.199.199.3 service tcp telnet 2301
I am able to access the switch at 10.199.199.3:2301
View 7 Replies
View Related
Mar 6, 2013
I have a server on the inside of my network (with a internet Routable IP). It has been requested to me that people from the internet access port 80, and that is translated at the firewall to port 7080. I have set up a temp Access rule to allow access to 7080 from the outside and it is accessable. I am not sure what I am doing wrong, but I am tion from 80 not able to get the translato 7080 to work.
View 1 Replies
View Related
Jun 1, 2011
I have ASA 5510 and public FTP server from my local network to external IP address, with static nat translation. All works, but I need request to ftp come from internal ASA interface (need use gateway different ASA). How configured ASA for forwarding request?
View 4 Replies
View Related
Mar 17, 2012
i wounder why i'm getting such log message whenever i'm trying to reach my remote site: No translation group found for tcp src outside XXXX dst dmz ZZZZ, i have a Cisco PIX515E firewall and that message is captured there, the traffic is going through a VPN tunnel (the VPN are up on both ends)
View 2 Replies
View Related
Dec 4, 2012
I am having an issue with a specific server that is not reachable from other sub nets. Every other device on the same sub net as the server is reachable via the other sub nets. This server is special because it's NAT'd to an external IP address and has several site-to-site VPN's set up. The firewall is a Cisco ASA 5510.
This is the error I see on the ASA syslog when I try to ping the server from another sub net: 3 Dec 05 2012 10:58:49 10.0.15.101 regular translation creation failed for icmp src inside:10.0.20.8 dst inside:10.0.15.101 (type 0, code 0)
The problem server is on sub net 10.0.20.0/24 and the server IP address is 10.0.20.8. Every device on the 10.0.20.0/24 sub net can hit the server, but devices on other sub nets cannot. For instance, a device on 10.0.15.0/24 cannot reach 10.0.20.8, but can reach other devices on 10.0.20.0/24.
View 1 Replies
View Related
Jun 26, 2011
Error message
305005: No translation group found for udp src c_dmz:10.0.176.120/51910 dst inside:195.244.192.16/53
305005: No translation group found for udp src c_dmz:10.0.176.120/51910 dst inside:195.244.192.166/53
[Code]....
I thought it needed a nat (c_dmz) command but I got the following error message
PIX(config)# nat (c_dmz) 0 0.0.0.0 0.0.0.0 0 0 nat 0 0.0.0.0 will be identity translated for outbound WARNING: Binding inside nat statement to outermost interface. WARNING: Keyword "outside" is probably missing.
View 2 Replies
View Related
