I implemented a ASA5510 with latest software version. I configured outside interface, default route, PAT to the outside interface. I am able to ping and telnet to the inside interface of the ASA.But internet is not working.Did i miss any configuration?i enabled icmp to outside,. i did a ping to the next hop from ASA. but it is not working.
View 6 RepliesI configured ASA 5510 with IOS 8.4.2 version. I configured SSH to outside and backup interface with any any permission.
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 backup
configured password with command
passwd < Password>
While connecting from outside through Putty i am not able to authenticate the password.
Aftter entering user name as pix its asking password. After entering its not authenticating.
I taken output by telnetting to inside after connecting to the firewall from outside and entering username as pix
PM-ASA-5510# sh ssh sessions
SID Client IP Version Mode Encryption Hmac State Username1 122.169.252.112 2.0 IN aes256-cbc sha1 KeysExchanged pix OUT aes256-cbc sha1 KeysExchanged pixSPM-ASA-5510#
Our NOC is trying to configure a site to site tunnel to one of our customers. The tunnel is up and operational, however we can't get our NAT rules to match what we want.
We are running ASA version 8.4(3)
The traffic is sourced from 172.16.1.50 (inside1) and destined to192.168.2.9 (outside), the nat configuration is posted below:
NOC-ASA5510-01# show run nat
nat (inside1,inside2) source static ng-noc-networks ng-noc-networks destination static ng-inside2-networks ng-inside2-networks
nat (inside1,outside) source static test test-EXT destination static otherside otherside
object network obj_any
nat (inside1,outside) dynamic interface dns
object network servers-noc
nat (inside1,outside) static 192.168.1.68
Here is the output from the show nat detailed:
NOC-ASA5510-01# show nat detail
Manual NAT Policies (Section 1)
I left off entry 1 but it doesnt have any translated hits either
2 (inside1) to (outside) source static test test-EXT destination static otherside otherside
translate_hits = 0, untranslate_hits = 624
Source - Origin: 172.16.1.50/32, Translated: 192.168.1.67/32
Destination - Origin:192.168.2.9/32, Translated:192.168.2.9/32
Auto NAT Policies (Section 2)
1 (inside1) to (outside) source static servers-noc 192.168.1.68
translate_hits = 0, untranslate_hits = 187
Source - Origin: 172.16.1.101/32, Translated: 192.168.1.68/32
2 (inside1) to (outside) source dynamic obj_any interface dns
translate_hits = 58417, untranslate_hits = 1511
Source - Origin: 0.0.0.0/0, Translated: 192.168.1.66/29
Here are the network objects:
object network test
host 172.16.1.50
object network test-EXT
host 192.168.1.67
[Code]...
I've got an ASA 5510 running 8.4.I have a host on an inside interface, with a static NAT configured on the ASA. The inbound/return half of the NAT doesn't appear to be working. [code] I run a ping from the host (192.168.100.98) to something on the outside (1.2.3.4)Running captures, I can see the outbound ping leaving, having been NATed OK. I can see the reply coming back in to the outside interface with the correct IP address, but I never get the final NATed packet appear on the inside interface. The packet just disappears inside the ASA.
View 2 Replies View RelatedI find are steps to turn on SSH access. I have quite a few customers with ASA5510's installed. SSH is set up and working fine on every one. After a period of time, you are no longer able to SSH into the firewall. Using Putty, it just sits there on a blank screen without giving a "denied access" message or a login prompt. Rebooting the firewall will solve the issue and SSH access works again. Today, I had a customer with and active/standby configuration where I had to reboot both of them to be able to log in. Most of my customers are on 8.2.software as most don't want to reconfigure for the new NAT, etc.
I'm sure others have seen this before since it appears to be occuring on almost every ASA that I have access to. Is there any fix to eliminate this or is there something that can be run from the ASDM that will grant SSH access again without just doing a reboot?
We have 2 ASA5510 and 2 ASA5525. Got a very weird error; up to release 8.4 eigrp works fine, after upgrading to 8.6 eigrp stops working.Can't see any neighbors; but same command from another asa on same network but with release 8.4: [code] I want to put the 5525 on production but would like to do it with latest release; could this be a bug on 8.6?
View 12 Replies View Relatedwe recently upgraded our ASA 5510 active/standby cluster from ASA Version 8.3.2 to 8.4.1(11). Unfortunately the standby ASA is now crashing a few seconds after the configuration was synchronized from the active ASA.
Also completely disabling HA, bringing the default config to standby ASA again and activating HA afterwards did not work. Also tried through the Wizard provided by ASDM to be sure to have no errors with requirements.
How to solve this without doing a downgrade back to 8.3.2. ?
I have an ASA 5510 and I am building a site-to-site vpn tunnel, peer on the other end is a sonicwall. I can initiate the tunnel from my end, but when he tries from his end it fails on phase 2 with this error in the logs:
"Rejecting IPSec tunnel: no matching crypto map entry for remote proxy"
Obviously our crypto map's don't match, i have it restricted to specific ports on my end and he had it wide open on his end, but said he is not sure how to restrict it down to specific ports. My question is why would I be able to bring the tunnel up on my end if the crypto map's don't match and he can't bring it up?
I have an ASA 5510 and I am building a site-to-site vpn tunnel, peer on the other end is a sonicwall. I can initiate the tunnel from my end, but when he tries from his end it fails on phase 2 with this error in the logs:
"Rejecting IPSec tunnel: no matching crypto map entry for remote proxy"
Obviously our crypto map's don't match, i have it restricted to specific ports on my end and he had it wide open on his end, but said he is not sure how to restrict it down to specific ports. My question is why would I be able to bring the tunnel up on my end if the crypto map's don't match and he can't bring it up?
I have an ASA with an outside ACL that is configured to allow 208.84.248.95 SIP/5060 to 1x.x.x.46. I show no hits. I added an ACL to do a packet capture, it sees the packet coming into the ASA but not going to the Serv Prov interface. I see hits on the vuong ACL but not the production acl_out ACL.. What is up?
NOTE:ACL_out is the ACL we use to allow outside traffic to enter our network.
FW1(config)# sh access-list | i 1.x.x.46
access-list acl_out line 1 extended permit ip host 63.x.x.140 host 1x.x.x.46 (hitcnt=0) 0xc09a9387 (*NO HITS)
access-list acl_out line 658 extended permit udp host 208.84.248.95 host 1x.x.x.46 eq sip (hitcnt=0) 0x0f327179 (NO HITS)
[code]...
It was tested and verified from the inside network to make sure the server is listening on that port. Below we created an ACL to allow all IP from another test PC to the Server IP 1x.x.x.46. We did a telnet to port 5060 and it showed hits but not on the acl_out ACL.
ccess-list vuong line 1 extended permit ip host 63.x.x.140 host 1x.x.x.46 (hitcnt=0) 0x2759fa92
FW1(config)# q
FW1# capture capture1 access-list vuong interface outside
[code]...
Below we applied the same ACL to the ServProv interface to see if traffic was going where it was supposed to . By trying to telnet to the 1x.x.x46 IP from 63.x.x.140 IP. Looking below, no traffic appeared on the capture2.
FW1# capture capture2 access-list vuong interface ServProv
FW1# sh capture capture2
0 packet captured
0 packet shown
[code]...
Capture 1 above shows the last 3 incoming messages initiated from 63.x.x.140 to the 1x.x.x.46! Vuong ACL belows shows 3 more hits.....nothing on the acl_out ACL???
FW1# sh access-list vuong
access-list vuong; 1 elements; name hash: 0x29df3e90
access-list vuong line 1 extended permit ip host 63.x.x.140 host 1x.x.x.46 (hitcnt=6) 0x2759fa92
[code]...
I've got an ASA 5510 that has been working like a charm for some time now. Until now we've not had to nat any resources to the outside. I created network objects for an internal host and an external host. The internal host has to respond to requests on tcp/2001.
The internal host has no problem accessing the internet, but when I attempt to access the internal host from the outside, I get the following:
4 Sep 20 2011 16:20:33 fw_outside_ip 62678 outside_host 2001 Deny tcp src outside:outside_host_ip/62678 dst inside_host:inside_host_ip/2001 by access-group "outside_access_in" [0x0, 0x0]
When I try to use the packet tracer to simulate the outside traffic, I get the following
5 Sep 20 2011 16:17:41 inside_host 2001 Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:outside_host/1065 dst inside_int:inside_host/2001 denied due to NAT reverse path failure
I've got over my NAT statement and access rule and can't find anything wrong with either.
Here are the pertinent NAT and access rule...
static (inside_int,outside) tcp interface 2001 inside_host 2001 netmask 255.255.255.255
access-list outside_access_in extended permit tcp host outside_host host inside_host eq 2001
i have here a ASA 5510 sec k9.
I build a Config with a DMZ,INSIDE and OUTSIDE Interface. My Plan is to use the IP-Address of the OUTSIDE Interface with PORT to setup a HTTP Server In the DMZ
But my Config doesn't work. And I have no Plan why .....
The Inside Interface have to work normal. The Traffic to the Internet is TRiggert from Inside with Dynamic PAT
ciscoasa(config)# exit
ciscoasa# show run
: Saved
:
ASA Version 8.4(1)
[Code].....
I have ASA 5510 connected as shown in attached diagram.Ideally when ASA 1 is active and if I boot Switch-1, ASA-2 shood take over. But that is not happening.When I boot SW1 , ASA-2 shows "Failover LAN Interface: failover Ethernet0/0 (Failed - No Switchover)" and remains standby.Fail over works properly If ASA-1 boots.
View 7 Replies View RelatedI have an ASA 5510 and have just started using object-groups which are super handy in theory, but not working in reality. I have a service object-group with a mix of tcp, icmp, and udp ports. Let's call it Sample_Port_Group. I'm trying to apply it to my dmz_access_in ACL. Here's the line giving me problems:
access-list dmz_access_in extended permit object-group Sample_Port_Group 192.168.1.1 any
The asa throws up an error between 192.168.1.1 and any. When I put up a ? after Sample_Port_Group, it gives me the option of putting in an IP address, any, etc. When I put in a ? after 192.168.1.1, it only gives me the option of putting in an IP address.URL
Those posts gave me the impression my line was possible, especially the "access-list outsideacl extended permit object-group myaclog interface inside any" line, which is at the end of the 2nd article linked.
I have an ASA 5510 attached to 2 internal networks. Everything is working except communications between the 2 internal interfaces.I can ping the FW from either interface and I can ping hosts on both networks from the CLI but can't get any traffic to pass.I'd like to open the connection to all traffic. [code]
View 33 Replies View RelatedI know that I've run into this before but I can't remember the fix. I have a 5510. The 3 interfaces involved are INSIDE, OUTSIDE, and GUEST. Corporate users are allowed to put their iPhones on the Guest network, but the problem is that their Exchange ActiveSync stops working. It is tied to the external DNS name of the OWA server (we'll say webmail.abc.com). So the users are funneled out one public IP on the OUTSIDE interface and are trying to communicate with the outside of the OWA server, which is NATed to another public IP on the same outside interface. What do I need to do on the ASA to allow users on the guest network (behind the GUEST interface) to access the mail server using its public IP (behind the INSIDE interface)
View 1 Replies View RelatedAfter I have upgraded our ASA 5510 to 8.4.2 I have problem with the management interface.Our former firmware 8.2.3 had no problem using the management interface as a DMZ zone, but after we upgraded to 8.4.2 we can't make it work.The interface and the protocol is up, when I type: show interface.But when I ping the interface from a computer connectet to the interface, nothing happens.
Even the logging shows nothing.
I have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
My ASA 5510 IOS version 8.4.2 CSC IOS version is 6.6.1125,I configured ACLs and Class maps to forward all HTTP,HTTPS,SMTP,PoP3 and FTP taffic to CSC.Here my issue is my CSC not getting updating from the internet and some email sites like Webmail and Gmail are not taking forward after entering credintials. If i removed ACL belongs to the HTTPS , all are working fine( CSC updating well and all email sites are working.)
View 1 Replies View RelatedIs it possible to have a Cisco ASA5510 with two internet connections performing as follows.
Internet A---------All traffic except LAN to LAN vpn
Internet B---------LAN to LAN vpn
I cant find anything definitive on google to say it will or wont, i know it cant do policy based routing.
I've created a DMZ on ASA5510, it can access anything internal but cannot get out to internet. I cannot manage the ASA from the DMZ subnet neither.
View 6 Replies View RelatedI can't seem to get internet access working from the DMZ network through our ASA 5510. PCs on the DMZ can ping the ASA but can't get out to the internet.I will attach a (cleaned) configure.
View 3 Replies View RelatedWe are in the process of getting two new connections pulled in that I would like to utilize in the following configuration.
DS3 - 45/45 I would like to use this circuit for all of our servers to NAT out of as well as our VPN tunnel to our remote site. It will be much more reliable than our cable line.
Cable Internet - 50/10 I would like to use this for all internet traffic that users generate. I would like to be able to fail over to the DS3 if this line goes down.
To get all traffic go out the cable line would take a dynamic NAT rule and a default route. How would I automate a failover to the DS3 with a backup route and dynamic NAT rule?
I understand that if the DS3 goes down it will take manual intervention to bring the tunnel back up and servers with static NAT will need reconfiguration.
I can get access to the internet from the ASA 5510 itself and that is confirmed via pings. However, anything behind the ASA does not have internet access, on any VLAN/sub-interface. I've attached my running-config.
View 2 Replies View Relatedthe set-up is: a DSL modem in half bridge (it does all the PPPoE connection) passes our static IP (55.167.x.x) to the ASA's outside interface ... (the modem has an IP of 192.168.1.1, but not sure this matters)
then I have one inside interface on 192.168.43.1, which connects to a server and we have a working site-to-site VPN between this server and a client.. so I know most of it's set up right ... nothing else is on the 192.168.43.0/24 network.
the management interface is on 200.200.1.0/24 so it's out of the way and incidentally connected to a dedicated PC, which also has console access via the blue serial cable.
the last interface Main_Network is on the 192.168.0.0/24 network and it's this that I'm trying to get to work... at the moment I just have one Windows PC connected directly (does it need to go through a switch?) into the ASA for testing with a static IP (192.168.0.72), but I can't ping anything outside from the PC... only the ASA's interface (at 192.168.0.30).. I have the gateway on the PC set as 192.168.0.30 by the way.
The ASA can ping all the inside machines and anything I like outside.
Here's my config ... the static routes are there for when this replaces the current modem/router and the whole network plugs into the ASA.
ciscoasa(config)# show running-config
: Saved
:
ASA Version 8.2(5)
!
hostname ciscoasa
[Code]......
I lost the ability for my Web server (or any servers in the DMZ) to access the Internet. However, the Web server is still being used fine from the Internet. Here is my config
ASA Version 8.4(2)
!
hostname xxxx
domain-name xxxxx
enable password xxxx encrypted
passwd xxxx encrypted
names
[code].....
I have installed ASA 5510 to limit sessions of Users to 170. But as soon as i put it infront of network before router, Internet goes down and i cannot browse or something.
The network is simple, Cisco three layer model with users on Wired LAN/Wireless LAN using WLC. Approx 2500-3000 users.
[code]...
I had an experience this week of installing a 5510 ASA with 8.4.3, also tried 8.4.4(1) with the strange effect that I randomly was losing contact with the internet. The interface stayed up/up. no errors or what so ever on the interface. Reseat of the DSL wire no result. Reseat of the outside interface cable made it work again. And after some time lost connectivity again. It did not recover by itself so had to let someone do a reseat again and again and.... The outside was using DHCP client. A lease was given and an IP also. Nothing strange to find. Talked to the provider which could see the DSL and the DHCP lease. Finally I downgraded the firmware to 8.4.2 and the problem was solved.
output
interface Ethernet0/0
nameif outside
[Code].....
I have recently made some chages to my ASA 5510 (not sure what) I was previously able to ping url... and I am now not able to ping anything on the Internet, but The Internet connectivity work perfectly.
View 7 Replies View RelatedI have been at this for the past few hours now. I just cannot get this device to pass through traffic to the internet. Here is the basic topology:
Default Gateway (ISP): 208.118.125.129/29
IP of outside int (e0/0): 208.118.125.130/29
ip of inside int (e0/1): 10.1.1.1/24
igniteCSGfw(config)# sho run
: Saved
:
ASA Version 8.0(4)
[Code].....
We are using an ASA 5510 as our gateway to our ISP. All of our VOIP traffic is sent to an Internet SIP provider for our outbound calls. Our pipe to the Internet is 100Mbps metro ethernet. I am trying to find a way to provide QoS for this traffic so that I can reserve 20Mbps of the available 100Mbps pipe for VOIP traffic.From what I've been able to figure out so far I would use a combination of priority queues and traffic policing. However, it seems that this is nearly impossible to accomplish because I cannot control the remote device that my ASA connects to because it is the ISP device. I could police traffic on the inside interface of the ASA. However, lets say that a client on our network starts downloading from an Internet host and the downloaded traffic saturates my Internet connection. I could police this incoming (from the Internet) traffic on my outside interface of the firewall. This would drop the packets but the bandwidth would have already been used by the time it reaches my firewall.Would the fact that I'm policing incoming traffic on my outside interface cause the sender to throttle down their transmit rate because packets are being dropped? Would this achieve my goal of guaranteeing available bandwidth for my VOIP traffic by not allowing other traffic to saturate the link?Most documents I find regarding this topic describe providing QoS for VOIP traffic traversing a VPN connection in which case you could configure both end devices.
View 1 Replies View RelatedWe have Cisco ASA 5510 256RAM running 8.2.4 with CSC 6.3.1172.4, it slows down internet traffics drastically when we do speed test, we get something like this, It the computer is bypassing the CSC, it gets This was done when there's very low traffic on the LAN and CPU is low usage on the CSC. The CSC has been re-imaged also but still doesn't solve the problem.
View 6 Replies View RelatedI have an ASA 5510. I am doing a new install at our new data center. I am having trouble getting internet access from an inside LAN interface to the outside WAN interface.Our colo center has given us the below IP info. [code]If I do a static config on my laptop of IP 198.145.XXX.82 Mask 255. 255. 255. 240 DG 198.145.XXX.81 I am able to get the web fine from the line in our rack. I used the ASDM software to setup the ASA. I set its WAN IP of 198. 145. XX X. 82 and mask as 255.255.255.40 for interface 0/0. For interface 0/1 I made a management LAN of 192.168.180.1 with mask of 255.255.255.0.I can connect to my LAN ok but do not have outside internet access. I have also tried .80 and .81 for the WAN IP of the ASA. [code]
View 8 Replies View Related