I have an ASA 5510 attached to 2 internal networks. Everything is working except communications between the 2 internal interfaces.I can ping the FW from either interface and I can ping hosts on both networks from the CLI but can't get any traffic to pass.I'd like to open the connection to all traffic. [code]
View 33 RepliesI'm trying to get a node in SVI1 on VRF1 to speak to another node in SVI2 on VRF2 to reach each other. After hours of failure, I went to outside resources. Everything I read on the internet says it's not possible on this platform and at least one TAC engineer seems to agree.
I just can't believe such a high-end data center switch is not capable of handling such a basic feature.
i have here a ASA 5510 sec k9.
I build a Config with a DMZ,INSIDE and OUTSIDE Interface. My Plan is to use the IP-Address of the OUTSIDE Interface with PORT to setup a HTTP Server In the DMZ
But my Config doesn't work. And I have no Plan why .....
The Inside Interface have to work normal. The Traffic to the Internet is TRiggert from Inside with Dynamic PAT
ciscoasa(config)# exit
ciscoasa# show run
: Saved
:
ASA Version 8.4(1)
[Code].....
After I have upgraded our ASA 5510 to 8.4.2 I have problem with the management interface.Our former firmware 8.2.3 had no problem using the management interface as a DMZ zone, but after we upgraded to 8.4.2 we can't make it work.The interface and the protocol is up, when I type: show interface.But when I ping the interface from a computer connectet to the interface, nothing happens.
Even the logging shows nothing.
I am unable to ping inside interface (Rin) to outside interface (Rout) of my Cisco ASA 5520 runing on ASA Version 8.4(1).
ASA Version 8.4(1)
!
hostname FW5520
[Code].....
I have a couple 3750 switches that I am trying to run VTP Version 3 on.one as primary and the other as "server" which implies secondary from my research. [code]Additionally, running a show VTP devices yields a "No VTP3 devices found" on both devices. Despite ensuring that the domainname and password match.I have a patch cable from Gi1/0/1 on switch one runnning to Gi1/0/1 which from what I read is acceptable on GigE.
View 2 Replies View RelatedI am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br Interface IP-Address OK? Method Status Protocol Ethernet0/0 x.x.x.x YES CONFIG up up Ethernet0/1 x.x.x.x YES CONFIG up up Ethernet0/2 unassigned YES unset administratively down down Internal-Control0/0 127.0.1.1 YES unset up up Internal-Data0/0 unassigned YES unset up up Management0/0 192.168.1.1 YES CONFIG up up
Have an ASA 5510. Setting up a new DMZ zone for wireless and it will only have Internet access. What are the steps so that users on this new DMZ subnet can VPN into the Outside interface on the same ASA?
View 4 Replies View RelatedI have a trouble with Cisco ASA 5510. I configured an SSL VPN with bookmarks to some application. When the users make access to the Web Portal they have to login twice: one for enter in the SSL and one for enter in the application.
How to bypass double authentication?
I attached the complete config. The earlier discussion, I cannot select reply. Looks like ACL is denying it. But I am not sure which one or how to permit it.
sh run
: Saved
:
ASA Version 8.0(4)
[Code].....
I would like to route traffic that are coming in and going out to the same interface on ASA. I am using inside interface with security-level 100. In this URL, [URL], ASA is able to do that.
View 5 Replies View RelatedI need the ssh access on my ASA outside interface and have added
ssh ipremoved 255.255.255.255 outside access-list acl_outside extended permit tcp host ipremoved any eq 22 but this is the log i get from ASA
Oct 06 2012 16:10:04: %ASA-3-710003: TCP access denied by ACL from ipremoved/39884 to outside:ipremoved/22
Cisco Adaptive Security Appliance Software Version 8.2(5) Device Manager Version 6.4(5)
I have a WAN interface and 2 LAN interface. I need both the LAN be able to access a server outside the network via the WAN (outside) interface. I am using a ASA 5510 firewall instead of a router, because I don't have a router. It looks simple enough but it does not work. I ping from the a PC (172.16.22.8) connected to LAN (inside) Network to 10.10.10.1 which is the WAN local interface also did not work. But from the ASA Firewall, I could ping my LAN (inside) PC. I followed a config i get from this forum. However, it did not work. Below my config.
interface Ethernet0/0
nameif outside
security-level 0
[Code]....
I'm not clear about the capabilities of the ASA 5510 GigE interfaces (eth0/0 and eth0/1) with an without IPSEC tunnels enabled.
This page [URL] shows a figure of 170Mbps 'Maximum 3DES/AES VPN Throughput'. Does that mean per IPSEC tunnel or for the whole interface if it is IPSEC-enabled?
I am having issues with the ASA 5510 management interface. I can't communicate with this interface. It is showing DOWN/DWON even if I type NO SHUT several times.
My existing config is as follows
our-asa-01# sh run
Saved
ASA Version 7.2(5)
hostname our-asa-01
names
dns-guard
interface Ethernet0/0
[code]....
On our ASA 5510 we already have one ISP link terminated on outside interface. There is correspoinding nat and global configured for outbound access to internet.
Now we need to terminate second ISP link on one of the DMZ interface to have redundancy for the primary ISP.
When primary ISP link or router is down we need to send all the traffic to secondary ISP router. How do we configure NAT and global for this condition that only when primary is down then only this NAT -Global should be used. Do we have anything like object tracking associated with the NAT-global.
So that as long as Primary RTR - object is up ASA will use the first NAT-Global pair. When primary ISP is down RTR-Object is not reachable then ASA will perform the second NAT-Global operation.
Also can we have default route pointing to Outside interface (primary ISP router) and in case of primary router failure it will point to secondary ISP. Do we have "track" in the static route commands on ASA.
May I know the reason why we cannot create interface vlan on Cisco ASA 5510?
View 2 Replies View RelatedFTP traffic routed from outside to the inside interface works fine. I have another interface with multiple sub-interfaces and vlans configured. FTP traffic routed from the outside to vlan2_servers is not making it through the firewall. I must be missing something. I have attached my config.
View 4 Replies View RelatedWhether it is possible to have same vlan on multiple interface on ASA 5510 and higher models ?
View 2 Replies View RelatedI am replacing an old Fw with a New ASA 5510 and I have a problem with a TCP Connection on My LAN InterfaceI joined a picture of what I want to do. [code] From the PC,I can Ping the Video Camera But I can't connect to it with HTTP.I don't understand, Packet Tracert allow the Http packet too. [code]
View 7 Replies View RelatedI have little experience with firewalls, what I've learned has been by dealing with issues like this that arise from time to time.I know, I need to upgrade the version. It's in the works now. Anyways, my question/problem is: Today I've received reports of slow internet access/activity and have noticed myself that it seems a bit slow today. On the dashboard of our asa 5510 the "outside interface" traffic usage is running contstantly high. It's at the top of the graph. How can I tell what is causing the spike in utilization. It usually runs at about 1500-2000 Kbps, and now it's up over 10,000.
View 2 Replies View RelatedI copied a Cisco 5510 startup-config to an identical Cisco 5510.After copying through tftp, I executed a reload. Everything looks good. Line by line compare results are the same.The problem is I can no longer use ASDM or ssh to interface with Cisco 5510.
View 25 Replies View RelatedI ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies View RelatedI have two ASA 5510 in an active-standby cluster, not that I think that the fact that they are clustered will be of any importance here so feel free to think of it as a single 5510. The internet connection is delivered in a single RJ45 connection. To be able to use it with the cluster there is a simple unmanaged switch connected between the ISP and the ASA's. I have two subnets with public addresses, for simplicity lets call them 1.1.1.0/24 and 2.2.2.0/24. Default routers are 1.1.1.1 and 2.2.2.1 respectively.
Can I somehow use both these subnets in the ASA's? Im currently using the first subnet and use PAT to direct traffic to internal servers. But if I want to use adresses from the second subnet wont that mess up the routing, since there is no way I can specify the default router for the second subnet? I have as of yet not tried anything, Im just trying to plan ahead and I cant seem to wrap my head around how this could possibly be done.
I can't move traffic (isakmp udp_port: 500 & ipsec nat traverse udp_port: 4500) from my dmz to the outside interface
View 1 Replies View RelatedI have disabled Unicast RPF on a Cisco ASA 5510 for one specific interface. However, how do I verify that RPF indeed has been disabled on that particular interface? It doesn't show up in the config, neither does it up when I issue the command "sh int interface'.
To disable the RPF feature, I issued the following command: no ip verify reverse-path interface interface_name
I working on a security solution using ASA firewall. Is it possible to setup a IPSec tunnels on each subinterface of a physical interface on ASA 5510?
View 3 Replies View RelatedI have configured redundant interface on ASA 5510
interface Redundant1
description *** INSIDES NETWORK ***
member-interface Ethernet0/1 (This is a 1000Mbps Port)
member-interface Ethernet0/2 (This one is 100Mbps)
no nameif
no security-level
no ip address
[code]....
Then... i issue following command and its OK!
ASA5510# show interface redundant 1 detail
Interface Redundant1 "", is up, line protocol is up
Hardware is i82546GB rev03, BW 1000 Mbps, DLY 10 usec
Auto-Duplex(Full-duplex), Auto-Speed(1000 Mbps)
Input flow control is unsupported, output flow control is off
[code]...
It's transfer correctly then i no shut and back to normal Primary core switch Gi0/30 Interface again, BUT redundant interface no revert back. I issued this command again BW remain 100Mbps.
ASA5510# show interface redundant 1 detail
Interface Redundant1 "", is up, line protocol is up
Hardware is i82546GB rev03, BW 100 Mbps, DLY 10 usec
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
[ code]....
I did manually shut down and no shut the secondary core switch interface Gi0/30 Its changed correctly to 1000Mbps .
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
we have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.
I’m trying to configure my ASA 5505, in order to allow my inbound and outbound mail communications. Here with this mail I’ve attached a diagram which illustrates my exact network setup along with ip addresses.
In this setup I’ve enabled port forwarding on my ADSL router (port 25 and 110) and configured the ASA accordingly, and my mail server is located inside my network.
My problem is currently I can send mails from my inside network to outside but my not receiving any mails which originate from outside. I’ve attached my current ASA configuration as well,
C:UsersSuthakarDocumentsOffice_DocsThakralABC Computers
Final config on ASA5505
host name Cisco
enable password 8Ry2YjIyt7RRXU24 encrypted
password 2KFQnbNIdI.2KYOU encrypted
names
!interface Vlan1
nameif inside
security-level 100
ip address 192.168.155.201 255.255.255.0
[Code] ......
I experinced critical problem for our customer service pertaing to communication fail for FT between FWSMs.
I can just find the log in FWSM as follows and can't find any physical log as interface down in C6500 at that moment.Now our FWSM OS version is 3.2(7) and jsut monitor-interface option is applied at outside interface in FWSM.
[code]...
I already opend the TAC case (SR 613646199) but I didn't get any correct cause for problem and they just recommend to change the FWSM through RMA.
having a bit of trouble setting up our 5510. None of us have ever played with a firewall before. We've got most of the basics covered. I was able to get to the outside world to do a software update to the box, but my laptop that sits in the inside can't see the outside. We only have the default access rules in place at the moment. Our old ISA firewall rules don't really translate all that well to this new box.
View 2 Replies View Related