Outside users with certain public ip addresses are not able to access our website. Below is a log from our ASA 5550 8.2(5) on one of the clients that's being dropped. Packet trace result shows that the outside public addresses are allowed. We do have a TAC case open.
View 1 RepliesI have the following problem, right now we have an ASA 5550 connected to the client´s side. A reset is being received on the client´s side, but when we run the sniffers on both extremes of the network, we can see that the reset is not being sent by the server´s side.
We have narrowed it down to the 5550 ASA, but have found no bug that matches the description.
The characateristics of the reset packet are the following:
- It is the only packet with a TTL of 255.
- Both server and client have very different window sizes, and the reset packet even though has the server´s ip and port as source of the packet, it has the client´s window size.
- It has a correct ack number.
-Before the reset is received, there are a couple of retransmissions of the last packet sent.
- We´re handling a VPN tunnel between both servers.
I started having connectivity issues between my core 4506E (Sup7E) and Cisco 2960S. There were input and CRC errors on Te int (SFP 10Gb - LRM) on 2960S, which cause the interface to reset and drop connections. While troubleshooting this issue, I have replaced patch cords and also had the tech checking the fiber. He said that there was some residue on one of the connectors, so the light levels fluctuated in 1300nm, but worked fine in 850. Well LRMs are using 1300, so he re-polished the tips, which worked to stabilize the light levels. After all that, I was still receiving the input/CRC errors, but the connection was NOT dropping. As my last resort I swapped the SFPs between the core and 2960, thinking I should start having issues on the core end. Well, here's what happened: I stopped receiving input/CRC errors on 2960 (also no errors on the core), but 2960s started generating Rx power high alarms: [code]
View 1 Replies View RelatedI am running XP SP3 with .NET Framework 3.5 SP1. The wireless network adapter works fine using either the Atheros Client Utility (my preference) or Windows Zero Config, Since someone mentioned the latter as possibly being necessary, I have been using it for these tests. It is, thus, not surprising that the wireless network adapter is present in and shows no problem in the Device Manager (devmgmt.msc), or ipconfig output; however, Xirrus WiFi Inspector shows "No adapters available" and does not function. How to get WiFi Inspector running?
View 2 Replies View RelatedI am using Xirrus WiFi inspector to survey the signal in y house and I notice a very strong signal at 160dBmMy home signal is in the region of -60 dBm so I am surprised to see such a strong signal at 160I have attached a screen shot so you can see BTOpenzone and BTHomeHub-WM9R with a high power.
View 3 Replies View Relatedi two 5550 firewall set up for redundance purpose . in failover we define two different ip add one for primary and one for secondary .interface Ethernet0/0 nameif outside security-level 0 ip address xxxx.0.0.0.1 255.255.255.0 standby xxxx.0.0.2!interface Ethernet1/0 nameif inside security-level 100 ip address 10.0.0.12 255.255.255.0 standby 10.0.0.11.default gateway for host will be 10.0.0.12 (primary fw address) however in case of failover , the secondary fw will be up with ip address that was assigned for primary .in this case the secondary ip add 10.0.0.11 is actually nerver used? similarly do i need to have two public ip address for outside (one for primary and one for secondary ) ? or in case if primary fails the secondary comes onlie and take the ip of primary fw . hence i only need to purchase just one ip address.
View 6 Replies View RelatedI have cisco 5550 Firewall, one messages appear in syslog server from Firewall, (warning) i want to stop this message from appearing syslog traps.
View 2 Replies View RelatedI am having two ASA 5550 firewall running in active/standby mode. With in last two months our secondary firewall got down automatically 3 times. Firewall is running with IOS version 7.1.2. how to proceed further troubleshooting because there are not any logs on firewall.
View 3 Replies View RelatedASA 5510 running without issues for a while but we needed extra port so added a 4GE SSM.
Having installed the 4GE SSM we had some issues with the card not liking a connection to our switches and only working by plugging directly from the server into the firewall, not great as we wanted extra servers on the line in the future. So we upgraded the firmware and no are at an impasse.
We have upgraded to 8.0(4)3 and now we cannot get any traffic through the port, we can't even connect to an external DNS server. Running a packet trace I get an immediate error on the first step '(l2_acl) FP L2 rule drop', and it appears as though the outside connection is down.
I have some experience on setting up basic port forwarding and NAT for internet access, webservers, mail but this has thrown me.
I have ASA5550 ruuning Version 8.3(1) with inside and outside interfaces as below [code] On the inside : I have a server (10.20.10.36) that need to be accessed from an outside host (Y.Y.131.34) , so I have the below NAT/ACL rules. [code] is it right that I have to add two ACL entry for outside host to the NATed IP of the inside server , then again add another ACL entry from the same outside host to the private IP of my inside server o get this communication done?
View 7 Replies View Relatedwe had just installed our ASA 5550 with IOS 8.0(2) a couple of week ago.
2 interfaces from each slot are being used ie 0/0 for Branch users comming via MPLS cloud , 0/1 for internal LAN users comming form Core Switch & 1/0 for Server farm LAN , 1/1 for Internet (outside)
the first 3 interface are considered inside with sec set at 100 while the 1/1 is outside with sec at 0.
Last night it suddenly started dropping all connections without any warning or any noticible log form the ASDM logging.
the connection drop would happen for 2 - 3 minutes and would work fine for the next 15 minutes or so..
after conencting the console , we found out that the IOS would suddelny go abrupt and show this display ...
TP-ASA(config)# TP-ASA(config)# TP-ASA(config)# Thread Name: Dispatch UnitPage fault: Address not mapped vector 0x0000000e edi 0x24d184b0 esi 0x0000000d ebp 0x1c6ceaf8 esp 0x1c6ceae0 ebx 0x09e965e0 edx
[Code]....
I have looked in the books I have (Cisco ASA, PIX and FWSM; ASA 8.0) and googled a good bit but can't seem to find any specific mention of how to do NAT exemption with v8.4. It seems NAT exemption (NAT 0 access-list) was deprecated. Using ASDM, there's no corresponding menu item for this that is obvious.
We have public addresses inside the ASA and want to allow in/outbound connections using these IP's without NAT. The ASA is a 5550.
Working as a consultant I find it annoying I cannot see a drop-down list in the AnyConnect client as you can with the traditional IPSEC VPN client with multiple profiles. How to modify the default profile to list multiple entries?
View 5 Replies View RelatedI need to understand if ASA 5550 ver 8.2(1) is comptible with IPv6, if not what is the upgrade path to make it IPv6 compatible. The requirement is dual stack of IPv4 and IPv6 should run in the same HA cluster and later will shift IPv6 completely.
The existing infrastructure is equipped with ASA with HA Active/Active mode. The command output for required details are attached here in txt mode.
I have Active Standby ASA5550 setup with VPN premium license. A few days back we had a requirement of SSL VPN connection for and we got a temporary from Cisco for same, this license expired and the ASA reverted to it's original license. 3 4 days after this we saw a sudden increase in CPU utilization (upto 90% + -5%) on the ASA during production hours but were not able to figure out the reason, in order to restore the services we failovered the firewall to secondary and everything worked fine. We were suspecting one of the following but there were no logs for any of this
1. The ASA hardware was haivng problem
2. Some client was doing a DoS attack to bring down the ASA (no logs for this as well).
We took a downtime to look further by failovering the ASA back to primary and it worked fine without any issues ruling out the 1st option. We also came across a licesing doc [URL]
Downgrading any license (for example, going from 10 contexts to 2 contexts).
# Note If a temporary license expires, and the permanent license is a downgrade, then you do not need to immediately reload the security appliance; the next time you reload, the permanent license is restored.
As per this doc, sooner or later a restart was required on the ASA. We restarted secondary ASA and everthing was fine but when we restarted the primary ASA by swtiching over to secondary some of the server (not all) in the DMZ stopped working (even ICMP unreachable) and only came back to normal when the primary ASA was restored and working fine (with failover).
The reboot was done by shuting down the physical link between the Core switch and ASA inside individually.
I am not sure what could be the issue that the servers in the DMZ wen unreachable.
In my Cisco ASA 5550, I need to set two different syslogs servers, and I need to send the system logs to the first one (only admins login/logout), and the traffic logs and all the rest (informational level) to the second one. Do you know if is it possible or not and, if yes, how to configure it?
View 6 Replies View RelatedI would like to work with two ASA's 5550 in HA (Acitve-Standby) like perimetral firewalls and also work with another ASA 5540 but like a SSL VPN Remote Access to end users.Which will be the best topology to this scenary?. Perhaps i need to put the ASA 5540 SSL VPN together with the ASA's in HA directly in a port.
View 1 Replies View RelatedI am using an ASA5550 for a complex secure network that has at least six "outside" networks. Each "outside" network is assigned to a specific port each set at level "0". I also have a DMZ, set to level "50". I am having difficulty with passing traffic from a host in the DMZ to all but one of the "outside" networks. Is there a limit to the number of "outside" interfaces? I will provide a redacted config file as soon as possible.
View 3 Replies View Relatedi have Cisco ASA 5550 and i want to do URL filtering using Web sense,can i use Micorsoft Forefront TMG2010 as websense server to do that?
the idea is to filter the HTTP & HTTPS URLs,if the Micorsoft Forefront TMG2010 is not suitable,refer to suitable Websense URL filtering server?
i m looking for asa 5550 product.Part # ASA5550-BUN-K9 - Cisco ASA 5550 Appliance with SW, HA, 8GE+1FE, 3DES/AES
1) does 5550 contains built in CSC / IPS modules.? why i m asking because the "quick refrence guide " indicates that expansion slots are not available.
2) can asa 5550 natively protects natively against networks attacks against virus / worms etc with out CSC OR IPS MODULE.?
I am about to carry out a migration from ASA 5550 to ASA 5555-X, however I cannot find any detailed document or reliable tool for this migration.
View 4 Replies View RelatedI cannot logon with adsm anymore.when I run adsm, I type in my pw, and the screen keeps displaying "contacting the device". No timeout, just stays this way.I've updated the java version, no luck.I can connect with SSH with no problem. device = asa5550, 8.2(1) asdm 6.2(1) [code]
notice that there is no "with cookie-based authentication" here -- is this relevant?
Rebooting the device is not really an option.
I have an issue were thousands of connections on the ASA are marked with flags E, below is a visual of the connection. Any ideas what could cause this marking? Also, I can't grasp what the meaing of an outside back connection (ie flags E).
TCP DMZ:X.X.X.X/139 Inside:X.X.X.X/1828, flags E, idle 9h37m, uptime 9h37m, timeout 15s, bytes 0
i'm installing a Firewall Cisco ASA 5550 with 8 Gigabit interfaces.
I have installed firmware 8.2.3.
Is it possible to make link aggregation on ASA to have more bandwith?
I have a couple of ASA5520 and ASA5550, and I wanted to know if it is worth it to upgrade the software from 8.2(4) to 8.2(5)? Because of the RAM I cannot upgrade to 8.3 for now.
View 1 Replies View RelatedI just got a brand new ASA 5550, i configured the port g0/0 on asa with an ip address 192.168.10.1 then configure my computer with ip 192.168.10.2 and default gateway is 192.168.10.1. I'm able to ping the asa from my computer. I remote to ASA thru the console port and try to copy iOS from flash to my pc but it doesn't work.
Cisco asa# copy flash tftp://192.168.10.2/asa804-k8.bin
Source file name []? asa804-k8.bin
Address or name of remote host [192.168.10.2]?
Destination file name [asa804-k8.bin]?
Writing file tftp://192.168.10.2/asa804-k8.bin...
!%Error writing tftp://192.168.10.2/asa804-k8.bin (Timed out attempting to connect)
Cisco asa#
I have two box cisco asa 5550 in multiple context mode and failover.
My network topology is:
Outside Network
•
•
•
DMZ2 Network • • • • (CISCO ASA 5550) • • • • DMZ1 Network
•
•
•
Inside Netowork
My interface "Inside Network" is full(I think).I can't diagnose this, based on command "sh interface gigabitEthernet"
109042974565 packets input, 100691006385765 bytes
94097614769 packets output, 59002295942465 bytes
999339444 packets dropped
My interface is 1GB, based on the above command, it is full?If interface is full, i have a problem! All the ports on asa firewall are using, how do resolve this? I can compress all data on this interface with class maps and policy maps?
We are having Cisco ASA 5550 appliance. from some days i am not able to access this ASA using ASDM. I am able to access ASA using SSH.[code]
At the same time standby firewall works perfectly fine with ASDM. I have tried by reloding the firewall, then it worked for 2 days & again stopped working.
Our users are using Xmanager to connect to a NNM connection which is going through a Cisco ASA5550 with 8.3. The session of Xmanager is getting terminated exactly after 1 hour and the users have to reconnect it again. How can we make the session to be up always, when I am bypassing the Firewall its always up.
View 2 Replies View RelatedIs it possible to use ports from 2 SFP and 2 RJ45 Interface on ASA 5550 Module 1.
View 5 Replies View Relatedif i can import an ASA 5550 8.2(5) in CSM version 3.3.1?
View 2 Replies View RelatedI would like to connect devices to my network so that their traffic passes through a proxy running on my computer. I figured the best way to do this is by setting the proxy on my router to the one I am running, but then I would need to have another connection to the computer running the proxy or else there would be an infinite loop ?? something like that. so:
Internet -> router (1) -> my proxy on comp A -> router (2) -> computer B
I have an 887VA-w connected at home. I am using ip virtual-reassembly an all interfaces (dialer and all internal VLANs), I am also using CBAC (currently setting up ZBF). The issue I am having is that I keep getting drop packet error messages and the reasons can differ. Below are some of the outputs I recieve: [code] I have done a show ip virtual-reassembly on all the interfaces and the counter is shown as 0.
View 6 Replies View Related