Cisco :: Prime DCNM 6.1(2) - LAN Client Not Working
Feb 5, 2013
I've recently installed a Prime DCNM 6.1(2) to a Windows 2008 R2 SP1 64 bit version. It seems to be working fine, apart from the DCNM-LAN client.If I login with the Java client, I got the GUI, however it remains blank - I can see the menu, but no data at all. It seems it cannot cummunicate with the DCNM server. DCNM-SAN client, the WEB client and the Device manager works fine, but I just cannot make this work.Tested it from Win2k3 SP2, Windows 7, and the server itself, with Java 1.6.31, 1.6.37, 1.7.13.
View 8 Replies
ADVERTISEMENT
May 29, 2013
I have installed the new version of DCNM Prime (Version: 6.2(1) and all installation process went well without any error or warning, DCNM SAN client works well I can loggin and manage my MDS and UCS, but I have big issue to run DCNM LAN client after successful logging I have window that freezing and nothing is displayed (see printscreen attachment) I reinstalled several time Java, installed four version different of Java, tried this client from three different PC and still have the same issue.
View 0 Replies
View Related
Feb 10, 2012
if i have a LMS server the newest version, and i bout Nexus 7K with its DCNM ver 5.2 (DCNM-N7K-K9) can i install the (DCNM-N7K-K9) license on the Cisco Prime LMS 4.1 Base so that i can manage Nexus through LMS?if this works Can I manage all Nexus switches also?
View 5 Replies
View Related
Mar 14, 2013
we are having trouble logging into the webinterface of our DCNM installation.
(Cisco Prime DCNM 6.1(2), Windows 2008 R2 SP1 64 bit version, US)
Everything seems to be working fine so far, except the login to the webinterface.
When calling https://<SERVER_IP> (we're using 443 and 8443 in our setup), the login page appears. Entering the credentials results in the message "Authentication Failed. Please try again.". We tried that from a remote machine and the server itself and are using local authentication (not RADIUS or LDAP, ...).
On the other hand, when running the DCNM LAN Client (using the same credentials not working for the webinterface), there is a link (see image below: "here") pointing to the webinterface.
[code]....
View 1 Replies
View Related
Jan 14, 2013
I'm running PI 1.2.1.012 and I'm having issues populating client information. Most of my switches are 2960 series. Specifically I get a lot of MAC Address "Unknown" and nothing in the IP address field. I probably get about 25% of the correct MAC address and 10% of the IP addresses. I also run CiscoWorks Prime LMS 4.3.2. and the user tracking information is about 98% correct pertaining to MAC address and IP address. My other network management tools also are very accurate.
View 1 Replies
View Related
Nov 18, 2012
after an upgrade of NCS 1.1.1.24 to CPI 1.2 on green field, it was not possible to reuse the GUI. During the upgrade, I''ve shortly seen an oracle DB error, but the upgrade was going through, without problems.At the end, it was not possible to use the GUI, and every trial to start the services was stopped with errors.I've found the following severe Bug ID's in the support forum: Bug CSCuc29378 Prime Infrastructure 1.2 won't start after a db restore/Upgrade from NCS1.1.1.24 Oracle DB bug as well: CSCtw59460.I see only a new installation from scratch (1.2) as solution, but the bug is not resolved in V1.2, as seen in the bug tool.
- As the customer has an v.1.0 license who worked with NCS 1.1.1, do I need an upgrade order to be able to activate an installation from the v 1.2 ova (new PAK)??
- I'm searching for a one year CPI partner license, because I heard about in some Cisco Live sessions, but I did not find a way to acces´s to it.
View 2 Replies
View Related
May 12, 2013
I have installed DCNM 6.2(1) on red hat 5.5 64bit and installed 4 evaluation (advanced) licenses on dcnm server:
DCNM-LAN-N3K-K9-EVAL
DCNM-LAN-N5K-K9-EVAL
DCNM-SAN-N5K-K9-EVAL
DCNM-SAN-M91-K9-EVAL
Licenses are activated on a total of 31 devices (nexus 5000 and 3000 series), data is being monitored, graphics are drawn. However under the Web user interface of DCNM, under Health, Virtual Port Channels (vPC) no data is shown. Performance, vPC is also empty. No vPC errors/notifications are displayed. The installed advanced-eval licenses should support all the bells and whistles (including vPC), but still- no monitoring is done about vPC-s. vPC-s are up and active. network is discovered and monitored via snmp v2c only. could this be limiting vPC discovery- needing snmpv3/ssh access?
View 1 Replies
View Related
May 9, 2013
I'm currently running CiscoWorks LMS 4.0.1 on Windows 2003 under VMware and just got upgrade licensing for Prime Infrastructure 1.2. I am assuming that I will need to upgrade the current server to Prime LMS 4.2 in order to ensure that data migration to Prime Infrastructure goes well. I am planning to follow Cisco's recommendation to run Prime LMS and Prime Infrastructure in parallel for a time and migrate individual functions.
My real question is about Syslog handling. All of the managed devices are currently sending Syslog data to LMS. As a last step in the migration, is it possible to change the IP address of the Prime Infrastructure server to replace the Prime LMS server so that the Prime Infrastructure server will just start getting all the Syslog data, or do I need to go change hundreds of managed devices to point to a new address?
View 2 Replies
View Related
Mar 12, 2013
What is the relation between: cisco NCScisco Prime LMSCisco Prime infrastructure.As i orderd a Cisco Prime infrastructure from a Cisco Partner and what i got is :
x2 cisco NCS appliances
x1 DVD cisco prime infrastructure
x1 DVD Cisco prime 4.2
View 4 Replies
View Related
Apr 18, 2012
I have installed DCNM 5.2(2c) on windows box to manage Nexus 7K devices.\ have for the time being one device that i have manage and i see often the following text:Discrepancy in device accounting log,Recommended action: clear the accounting log and discover the device. Device details are not available.How can i delete the accounting log and why do i have this message ?
View 4 Replies
View Related
Feb 10, 2012
Does DCNM (DCNM-N7K-K9) ver 5.2 on Nexus 7k manage nexus 5k??
View 2 Replies
View Related
Dec 20, 2012
I am unable to discover 2 Nexus 5548 with the SAN client of DCNM 5.2(2e)
These Nexus are used like LAN and SAN switch. Each Nexus is a SAN fabric. I would want to use DCNM in order to configurate the zone/zoneset via GUI. These Nexus 5548 run 5.1(3)N2(1b) release.
The Nexus ARE NOT managed via the Mgmt interface (OOB) but they are managed via an interface vlan (InB)
I could not configure rightly
- the snmp-server user (SNMP user V1/v2 or V3 + group ? ) CLI on Nx
- to configure the discovery in order that DCNM discover each fabric either from web GU interface or java SAN client
View 1 Replies
View Related
Jan 2, 2012
It's been discovering a 6513 for over 90 minutes. Is this an expected duration or is something likely malfunctioning or is it just the sheer # of interfaces that it must process? The Nexus 5k's that it has discovered progressed fairly quickly.
View 1 Replies
View Related
Feb 21, 2012
I am trying to get our DCNM to discover the 5548. When I put my credentials for that appliance. I get this error .Failed Device x.x.x.x OS Version 5.1(3)N1(1) is not supported . The DCNM version we have is 5.2(1)S74.
View 1 Replies
View Related
Feb 10, 2012
if i have just DCNM-N7K-K9 (DCNM for LAN Enterprise License for one Nexus 7000 Chassis) installed on a server, i can manage all nexus switches like 5k and 2k??
View 1 Replies
View Related
Jun 18, 2012
We've gotten two Nexus 7009's in and I'm starting to configure them when I found I couldn't add VDCs. I found there was no license installed but the only licenses I found that came with them are "Cisco DCNM for LAN Enterprise Lic for one Nexus 7000 Chassis". So my question is this - do I need to configure a DCNM server to get the license pushed to these two 7009s or should there be another PAK for each chassis that I can register and get my enterprise services?
View 1 Replies
View Related
Dec 12, 2012
, I have ipsec vpn setup on an asa5505 at one of my office locations but when I try to log in to the vpn with the vpn client it just dont work but I have a Linux laptop with vpnc loaded and that connects just fine no problems there ? by the way on my windows system i Have vpn client 5.0.07 asa5505 8.0.(4) asdm 6.1.(3)
View 5 Replies
View Related
Mar 11, 2013
I have a situation here where after migrating from PIX 6.3 to ASA 8.4, VPN connection from window server 2003 and 2008 fail to connect. Strangely, win7 or win 8 works perfectly well.
It failed due to
reason=DEL_REASON-IKE_NEG_FAILED
The diff we can see is win 7 is 32 bits and the server client version is 64bits.
View 1 Replies
View Related
Jul 20, 2011
I installed on 2 different PCs (Win7 64-bit) the Cisco VPN Client 5.0.07 with the same VPN profile for 2 different users. We use an ASA5505 (8.0(5) sec plus license) as the VPN end point for the clients. The VPN Clients can connect simultaneously to the ASA, they receive the split tunnel infos but only ONE client can ping the internal network ip range. The other one has no access to the internal resources! When they separately try to connect, there is no problem. Each of them can reach the internal net.On other 2 PCs (Win 7 32-bit) the clients have no problem reaching the internal net (simultaneously connect).
View 0 Replies
View Related
Feb 26, 2011
I recently upgraded from a WRT54G and am having issues with a Win7 PC with wireless-N. Initially I had it configured static at 192.168.100.100 and everything worked, but the speeds were miserable (I followed all the forum posts and recommended settings). I noticed in the Status section of the router pages that the system showed up with the correct MAC address, but the IP showed as 192.168.100.10, which is the same as the router. Assuming this might be causing issues, I set a reservation for the system at .100 and set the client to use DHCP. However, now it won't pull an IP address at all. The status pages show the client with the correct MAC address, but an IP of 0.0.0.0. I've verified the MAC address a dozen times and rebooted the router and the client dozens of times with no change. Even when I removed the reservation, the system won't pick up an IP. I have a wireless-G client that's pulling an IP fine, so I know it's sort of working. The wired LAN is working fine, too. There are no IP conflicts, either. I changed DHCP to 'Always Broadcast (compatibility for some DHCP clients), but no change there, either. The client sees the network and still has a good signal, but just won't grab an IP.
I'm running Hardware Version: B1 / Firmware Version: 2.01NA
View 2 Replies
View Related
Aug 29, 2011
A customer of mine has two RV082 in different locations. The "main" router is providing a gateway-to-gateway VPN tunnel, and is also used by a few road warriors for VPN access. We've had some issues with the "main" router lately, so we've decided to exchange it for a brand new device (v3). The old RV082 was a hardware revision v2 device, so I had to manually rebuild the config on the new router. The new router is working fine so far - connectivity and gateway-to-gateway VPN are fine. IPsec Client VPN, however, doesn't work at all. The config of the new router is identical to the config of the old one, IPsec Client VPN used to work fine on the old router.
The router is running the latest firmware (v4.0.4.02-tm). I've been trying to make IPsec VPN work with "QuickVPNplus ver: 1.0.6" and the "Cisco QuickVPN Client v1.4.2.1". From what I understand, both programs first connect to the routers external IP and download some sort of VPN config file. The info in that file is then used to create the actual connection. The problem is that the config file is invalid. It contains HTML code instead of config data. This is the code: "<HTML><HEAD><meta http-equiv="refresh" content="0; URL=/cgi-bin/welcome.cgi"></HEAD><BODY></BODY></HTML>". The URL is the same I see when logging in to the admin interface of the router. The Cisco client tells me in its "wget_error.txt": "rwConnStart message=All 1 wget requests did not return a valid vpnserver.conf". Both clients connect to the router fine, and the config download itself is working - only the returned data is invalid.
I've already tried lots of stuff to make the problem go away - enabling/disabling the firewall, VPN passthrough options, and other things. I'm beginning to think that there may be a bug in the firmware I'm using, or that the way Client VPN works has changed in a way that makes connecting with a client implementing the "old" method impossible. By the way, PPTP is working fine, so we're using it as a temporary workaround. My client, however, isn't happy with this workaround - he bought a relatively expensive router so he can make use of its advanced features, after all.
View 8 Replies
View Related
Aug 29, 2011
I have a user using windows 7 64 bit. I tried vpnclient-winx64-msi-5.0.07.0290-k9.exe and vpnclient-winx64-msi-5.0.07.0440-k9.exe. Installation is fine. Connecting is fine. But no traffic goes through.The remote end cisco is 1811 VPN Server split tunnel. User get authenticated by Radius server.
After connected, user get the correct IP address. In router, sh crypto session, it has SA, etc. But sh ip route, can't find the Static route point back to the client IP like other connections.
At user end, windows show the IP address but no gateway. Windows route print shows the VPN network via gateway xxx.xxx.xxx.1 which is not available.Other 32bit users have no issues with VPN.
View 1 Replies
View Related
Aug 9, 2011
Attempts to run remote desktop client a laptop on a tower using a CAT 5 Crossover isn't working. After starting the remote desktop on the laptop, I'm asked to identify the other computer, which I do, and a remote desktop window with a black background pops up, as expected. But I expect an opportunity to login will be displayed after a second or so. That never happens. After about a minute this pops up:Remote Desktop Disconnected?Your Remote Desktop session has ended.The connection to the remote computer was lost, possibly due to network connectivity problems. Try connecting to the remote computer again. If the problem continues, contact your network administrator or technical support.
My clients are impressed with my ability to setup their networks, Linksys routers with WIFI. But toss something unfamiliar into the mix, like this situation, and I'm pretty lost, pretty quick.
Environment:
Hospital's WIFI.
Laptop running XP Home with WIFI and Ethernet.
Tower running Win 7 Ultra with Ethernet.
Cat 5 crossover cable.
Goal:Configure laptop to access Hospital's WIFI. This is successful, I'm using it to post this. Configure laptop run a remote desktop with the tower as the server. The tower, running Win 7, has no monitor. I don't have a flat screen monitor, and didn't feel like dragging an 80 pound 24 inch Nokia into the hospital.After reading some sites while trying to figure this out, I gave the laptop the same group name, workgroup, as the tower.In my experience, starting the tower has been, turn it on, and it boots to Win 7. But I can't watch that happen without a monitor. I can't configure the the tower's network connections without a monitor either.I purchased the CAT 5 crossover cable yesterday, for this occasion. The label on the plastic bag it was packaged in had the word "Crossover" on it. I connect the CAT 5 to the laptop's single ethernet connection, and to the tower's Intel pro card. At home the laptop is on WIFI, the tower connects to the router.
View 4 Replies
View Related
Jan 15, 2013
i have configured remote access VPN to cisco ASA 5520, Cisco vpn client is connecting fine and both phases are coming up but ipsec phase packets are not encapsulating. and ima not able reach the remote subnets 192.168.10.0 and 192.168.180.0. [code]
View 4 Replies
View Related
Sep 7, 2011
I'm having a wierd issue with the VPN client installed on Windows. Eventhough it connects and receive and IP address, I'm not able to access any of the servers on the remote network.
Is there any special configuration need it for it to work on Windows 7 proffesional?
The client works perfect with windows XP, we have a ASA 5510 Version 8.2(2) is in routed Mode
View 2 Replies
View Related
Jul 16, 2012
Wireless client connected to a 3602i AP running on 2500 series WLC with a latest 7.2 code. Client will now connect to AT&T vpn client - success.Client will connect to SAP application using netweaver gui - failed.With the same scenario, except for the access point being used, client will connect to SAP application using netweaver gui
1242AP IOS/CAPWAP - success
1252 CAPWAP - success
3500 CAPWAP - success
Whats with the 3600 series APs that i cant pass traffic with the SAP application?
Troubleshooting done:
802.11n disabled - still failed
Clean Air disabled - still failed
MFP disabled - still failed
View 4 Replies
View Related
May 15, 2012
I have a Cisco ASA5520 that I have setup to allow a GRE tunnel through from a router at site B. This all works fine when I use the below NAT with associated router object on the inside
object network SWTEST nat (inside,outside) static interface
My problem comes in that this kills off my Cleintless VPN connection to the same firewall, I changed my NAT to point at another of my statically assigned IP addresses, and then nothing works. Can anyone help with what I've done wrong, or what i should do? My rule base allows any GRE in from the source, and rules all look fine.
View 2 Replies
View Related
Nov 11, 2010
Any working configuration to connect the iPad VPN-client (IPSEC) to the RV042?
View 16 Replies
View Related
Mar 14, 2013
i've configured Cisco VPN CLient on a router 2821, and it is working fine.I could access inside resourses normally>the problem is that when i connect with VPN i lost connectivity to internet? What is wrong with my configuration? Below the running config of the router.
CISCO2821#sh run
Building configuration...
Current configuration : 5834 bytes
!
version 12.4
[Code].....
View 3 Replies
View Related
Mar 20, 2012
i have a question about tunneling a software EasyVPN client to a client ASA Network. It looks like this:
EasyVPN Server 192.168.202.0/24 Network extension mode to Client EasyVPN ASA 192.168.1.0/24 This works fine in both directions. But now i want to connect the client ASA network via EasyVPN software client from outside. The user are already able to connect to the ASA Server on its static outside IP obtaining an IP from a 192.168.21.0/24 pool. This works fine. But how am i able to connect to the 192.168.1.0/24 network from this client?
View 5 Replies
View Related
Apr 18, 2013
how to make the java SSH thin client applet bigger in SSL VPN Clientless portal?It works and all that but the window is literally half the size of the monitor and unworkable. You can't even hit tab! (tab moves focus around the browser...)I am using the latest java applet (Oct 2012) and ASA OS 8.4(5)
View 3 Replies
View Related
Apr 21, 2013
Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
View 4 Replies
View Related
Jun 12, 2012
I recently installed LMS 4.2 appliance and I noticed that the web administration page was really slow. I checked the CPU utilization in VMware and it was at 55%.
View 1 Replies
View Related
