I'm connected to my remote access vpn and am getting the below error, wierd thing i only get this error for ICMP, i can browse data on our network retrieve files etc, but pings fail for some reason
NAT-T is enabled
NAT rules are in place
ICMP is not blocked as can ping elsewhere
Where to being looking as to why only ICMP fails?
I have site-to-site VPN and IPsec VPN installed on ASA 5505. VPNs work OK except few stranges:I can't ping 192.168.17.104 from remote ip 192.168.17.138 - 305006 192.168.17.138 regular translation creation failed for icmp src OLD-Private:192.168.17.104 dst OLD-Private:192.168.17.138 (type 0, code 0) in the same time I able to ping 192.168.17.104 from my network 192.168.10.0 and can ping from ASA No firewall at 192.168.17.104?How to fix it?
There is my config:
ASA Version 8.2(2)
!hostname ASA5505domain-name domainenable password password encryptedpasswd password encryptednames!interface Vlan1 description INTERNET mac-address 0000.0000.0001 nameif WAN security-level 0 ip address a.a.a.a 255.255.255.248 standby a1.a1.a1.a1 ospf cost 10!interface Vlan2 description OLD-PRIVATE mac-address 0000.0000.0102 nameif OLD-Private security-level 100 ip address 192.168.17.2 255.255.255.0 standby 192.168.17.3 ospf cost 10!interface Vlan6 description MANAGEMENT mac-address 0000.0000.0106 nameif Management security-level 100 ip address 192.168.1.2 255.255.255.0 standby 192.168.1.3 ospf cost 10!interface Vlan100 description LAN Failover Interface!interface Ethernet0/0!interface Ethernet0/1 shutdown!interface Ethernet0/2 shutdown!interface Ethernet0/3 shutdown!interface Ethernet0/4 shutdown!interface
[code]....
We have a PIX with 3 interfaces. Inside, Outside,DMZ.
On my DMZ we have some clients that come in and remotely connect back to there office via MSPPTP. I setup the ASA with this to get rid of the error message: regular translation creation failed for protocol 47 src
policy-map global-policy
inspection_default
inspect pptp
Now when the dmz client tries to connect back to there PPTP server I get the following error.
172.31.10.204 0 24.172.85.162 37624 Teardown dynamic GRE translation from dmz:172.31.10.204/0 to outside:24.172.85.162/37624 duration 0:01:30
172.31.10.204 1069 173.188.74.155 1723 Deny TCP (no connection) from 172.31.10.204/1069 to 173.188.74.155/1723 flags PSH ACK on interface dmz
172.31.10.204 173.188.74.155 63767 Teardown GRE connection 8393958 from dmz:172.31.10.204 to outside:173.188.74.155/63767 duration 0:01:08 bytes [ code]...
I am having an issue with a specific server that is not reachable from other sub nets. Every other device on the same sub net as the server is reachable via the other sub nets. This server is special because it's NAT'd to an external IP address and has several site-to-site VPN's set up. The firewall is a Cisco ASA 5510.
This is the error I see on the ASA syslog when I try to ping the server from another sub net: 3 Dec 05 2012 10:58:49 10.0.15.101 regular translation creation failed for icmp src inside:10.0.20.8 dst inside:10.0.15.101 (type 0, code 0)
The problem server is on sub net 10.0.20.0/24 and the server IP address is 10.0.20.8. Every device on the 10.0.20.0/24 sub net can hit the server, but devices on other sub nets cannot. For instance, a device on 10.0.15.0/24 cannot reach 10.0.20.8, but can reach other devices on 10.0.20.0/24.
After adding a NAT rule on Friday morning, I'm now getting a bunch of "portmap translation creation failed" messages from my ASA5520. (It's currently running 8.4(3).) The failure errors appear to have nothing to do with the change that was made. [code] I have very similar rules in place for other vendors to access other machines. The only difference between this new one and those old ones is the use of the objects in the rule instead of the direct IP addresses. This is also the first one that invovles a range instead of a specific address or network. [code]
View 4 Replies View RelatedTwo Vlans (ID1 and 100)are on a Cat 4500, which connects to an ASA, interface DMZ. On 4500, there is default route point to the ASA DMZ interface Issue, server on vlan 100 cannot ping a server on Vlan 1, vice verse. When I enable the realtime log, it gives me a “Translation creation failed” message, please see the attached files.
View 1 Replies View Related See the error below on my ASA5510.
305006 200.200.0.34 53 portmap translation creation failed for udp src inside:192.168.1.4/1047 dst outside:200.200.0.34/53
The first two computers work normally( IP 2 and 3) , but the third computer gets ip does not work on the Internet.
We have an ASA 5540 with 8.2(5)
Last three days in early afternoon we start getting these errors in the log and webpages either won't load or pages only half load.
3|Mar 22 2013|13:22:24|305006|184.73.105.115|443|||portmap translation creation failed for tcp src inside:10.10.176.114/58217 dst outside:184.73.105.115/443
3|Mar 22 2013|13:22:24|305006|54.243.129.71|80|||portmap translation creation failed for tcp src inside:10.35.54.37/1517 dst outside:54.243.129.71/80
[Code].....
i have a query regarding the no. of isakmp policy priority creating..when i create a new policy in ASA 5500 firewall, i get the below error...i assume it will support only 20 nos, where as we can use between 1-65535.. can anyone from cisco confirm it...running version is 8.x & VPN Plus license.Policy limit reached. No more than 20 isakmp policies can be configured.”
View 2 Replies View RelatedI need to implement a DMZ in my office. Before talking about the configuration , i would like to know best practises of implementing DMZ.My questions are,is traffic from inside to DMZ is permit by default?,What about DMZ to Inside traffic ?,Is it necessary to do a NAT from inside to DMZ with the same IP as of inside,What is the use of " static (inside,dmz) 192.168.1.0 192.168.1.0 netmask 255.255.255.0 ? is it a no nat statement?,Is it necessary to permit traffic from DMZ to inside?,Suppose i have a web server in DMZ, for inside host whether it will take path through ASA or path through internet?
View 17 Replies View RelatedHow do you create a vlan? In enable mode, there is no "vlan" command.
View 4 Replies View RelatedI am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View RelatedI need to create a DMZ zone in my network. One server need to be put in DMZ. I have a PIX 515E 6.3.3. It has free port to create DMZ.
1) Put a new switch for DMZ zone
2) Connect it to the DMZ port
3) Create a NAT for inside to DMZ with same IP as inside
4) Create ACL for permiting traffic to DMZ and apply it to outside interface
5) Create ACl for permitting traffic from DMZ to inside
6) Routing for DMZ in PIX
I have cisco switch model WS-C3750G-12S-D. It is in transparent mode. I am getting below error message when tried to create new vlan.
Proposed configuration exceeds the limit of 1005 VLANs that can be supported on this platform. Reduce the number of VLANs proposed to be within this limit.
After deleting few unnecessary vlans, it allowed me to create.
3750#sh vtp statusVTP Version : running VTP1 (VTP2 capable)Configuration Revision : 0Maximum VLANs supported locally : 1005Number of existing VLANs : 959VTP Operating Mode : TransparentVTP Domain Name : VTP Pruning Mode : DisabledVTP V2 Mode : DisabledVTP Traps Generation : DisabledMD5 digest : 0xBC 0xA7 0xEC 0xDE 0x36 0x6C 0x61 0xB4 Configuration last modified by 97.193.17.172 at 0-0-00 00:00:00
I confused with terms 'maximum supported vlans' and 'maximum locally supported vlans'. If switch is supporting vlans 1-4094 means it should also allow to create locally. Otherwise how they will pass through the switch trunks without local creation.
On the ASA running the 8.4.4.1 code in transparent mode. Can I create sub interfaces in different vlans and attach them to different BVI groups?
switch---trunk---ASA---Trunk---switch
Gig0/1.1 vlan 100 bridge-gr1 Gig0/2.1 vlan 101 bridge-gr1
Gig0/1.2 vlan 200 bridge-gr2 Gig0/2.2 vlan 201 bridge-gr2
I could not find any report in ACS 5.3 which gives details on user creation and deletion in ACS. This feature was there in ACS 4.x but it seems not provided in 5.3 version.
View 3 Replies View RelatedMy backup userid, password, privi 15 on all our company routers Say around 300 routers, it is difficult to log in each router and create a backup account, i heard from one of my friend that i can create a backup account and can upload thru the kiwicat tool and it will automatically creates my backup account on all the routers. Procedure to create this.
View 6 Replies View Relatedi have acs 5.2 i need to create a network admin policy to our nx-os devices such as nexus switches, how this will be done on acs 5.2?
View 0 Replies View RelatedI have a query regarding the deletion and creation of one of my SVI interface on 6513 ,The reason behind it as follows.My traffic get to Internet in this manner
proxy(external int.)[IP:192.168.1.30] --> Gi0/9[6513 in VLAN 170] --> SVI VLAN 170[IP:192.168.1.10] --> Gi0/10[In VLAN 170] -->ASR[IP:192.168.1.20],I need to assign this VLAN ie 170 to my inside interface of firewall but it was mentioned in books like this "Assign the VLAN for the FWSM before it is applied to the MultilayerSwitch Feature Card (MSFC)." so I am thinking the following steps to assign VLAN 170 to firewall group first before creating SVI Interface for it
1.Remove all currently assign ie Gi 0/9 & Gi0/10 interfaces from this VLAN and then delete this VLAN.
2.Create the same SVI ie VLAN 170[IP:192.168.1.10] by this way the issue can be resolved.
As in part of my configuration PBR is define like this .
interface Vlan170
description "PUBLIC IP VLAN"
ip address 192.168.1.20. 255.255.255.0
ip policy route-map NAT
route-map NAT permit 10
match ip address 101
set ip next-hop 192.168.1.10
I need to clearify what impact it may have on PBR part if I delete and create the VLAN 170.Will the traffic move to the inside interface of FWSM.
What is the difference between DWDM/CWDM and "regular" SFP's? By "regular" I mean Rx and Tx are fixed to specific wavelength. As I have understood, at least Rx of WDM SFP's accepts a range of wavelengths
View 2 Replies View Related have 2 inside networks:
object network INSIDE_10.6
subnet 10.6.0.0 255.255.0.0
object network INSIDE_192.168
subnet 192.168.0.0 255.255.255.0
I grouped these 2 into 1 object-group:
object-group network INSIDE
network-object object INSIDE_10.6
network-object object INSIDE_192.168
Public IP address used for PAT:
object network PAT
host 152.x.x.x
I used the following statement to create Dynamic PAT to public IP address:
object network INSIDE_10.6
nat (any,any) dynamic PAT
object network INSIDE_192.168
nat (any,any) dynamic PAT
Is that correct? Also I'm using one public address to PAT both inside networks. Is there any dvantage of using 2 different ones, so each inside network would be PAT to its own address?
We have a customer in a country where the local telecom hands out the data E1 link in a G703 interface with two coaxial cables (Tx & Rx) out of a Watson/Schmidt Telecom SHDSL modem.
We need a way to convert the G703 cables and signaling to a regular RJ45 so that we can connect it to the customer firewall which has regular gigabit Ethernet connections. Some have suggested a 1941 with a serial and gigabit cards. We just need a affordable solution for this and the configuration.
we managed to integrate our newly setup ACS 5.2 to our regional domain. now im creating a Device Admin access Policy for Regional Network Admin group and Regional Network Operators group. each having full and read access respectively.
i already have the default identity policy and authorization policy with with command sets fullaccess and showonly for each group, now i dont know how can i match the AD group regionaladm and regionalops so that each user falls under one of these groups will have a correct read/write access.
I use my laptop in Italy most of the time on a wireless router that uses a PPPoE connection. Once I'd got my head around setting that up it works fine.However since I've come back to the UK today I now cannot connect to a regular wireless router, its just not 'seeing it'. I have used this connection in the UK before without problems and the setting are all still saved from my last trip back but it doesnt show up when I try to connect.Is this something to do with the laptop being set up on the PPPoE connection in Italy? Ive deleted the PPPoE connection but that hasnt made a difference
View 3 Replies View RelatedI am configuring a pix 525,i just found out how to activate the subinterface on it so that's good,the box has a primary unit and secondary unit, both are connected from G0 to redundant switches,if i do a show failover, it says it's using the serial based lan failover, which is fine by me,however, do i need to create a single, regular interface.. or a redundant interface?,i.e. if i create a regular subinterface, will failover still apply to this interface?,or for failover to work, do i need to create a redundant interface (with a redundant id)? i do not seem to have the option to create a subinterface when adding a redundant interface.
View 7 Replies View Relatedi have a Cisco ASA 5520 8.4(1) with a ASA 5520 VPN Plus license
i want to use the management interface as a regular interface (using the no management-only command)is this interface a Gig interface as well ?
I have a ASA 5510, it does webfilter using regular expression. [URL]
I block ".facebook.com" and it was successfull. But somehow other users is using https to access to FB. how do i filter HTTPS?
I am connecting to a Wireless network, through a ZyXel ZyAIR G-4100v2 router. My problem is that I am experiencing very regular packet loss every minute or so. This lasts for around 5-10 seconds on average. I am running XP with the latest service pack. So far, I have checked out;Wireless Zero Config scanning of new stations (disabled that feature).Xirrus network scan (signal is fine and consistent). I am not suffering from any degredation in signal, the problem seems to be that the router is simply not allowing anything through at regular intervals.
View 1 Replies View RelatedI am trying to secure changes to switches using ACS 5.3 and allowing our technicians to only change the vlan for user ports on the switches. How can I use regular expressions to filter out the 1/1/# ports so that those ports cannot be accessed in config mode? If I allow the following, it allows access to all interfaces with 'gi' in them.
View 1 Replies View RelatedWe are running WLAN using WPA2-enterprise with AES & IAS server.Mostly we are using AP's 1131 and Cisco WLC 4400.I added on a new location 2 AP 1142G and since the installation I got 3-4 clients having regular disconnections.Basically they are connected immediately to the infrastructure but after a certain amount of time the Win7 icon is having this yellow exclamation sign, and we can see that the connectivity is gone (however the IP settings seems to be still in place, but ping or network browsing is not possible).Stopping the WLAN and starting it again solve immediately the issue (via software or via the notebook switch). Normally the problem doesn't resolve by itself.
I was working beside the laptop having the problem with (my own laptop) during the person got 3 disconnections, mine was running like a charm.We have 85% of the people there working errors free.Checked the 1142 AP for any logs or errors, interfaces status etc...Checked the switches behind, interfaces seems running smoothlyChecked IAS / WLC / WCS for any logs that can indicate an issueCompared WLAN adapter settings of the faulty laptop with mine, discovered some differences and adapted it.Compare the WLAN SSID config in Win7 with mine and adapted the slighty differences found.Used WCS troubleshooting client tool.What I will do again :Verify if the persons having the issue have the same laptop modelVerify settings in the BIOS Verify WLAN adapter driver versionVerify BIOS versionUse WCS troubleshooting client tool on my own laptop at this place.
I've recently switched to an ASA 5510 on 8.4(3) coming from a Checkpoint NGX platform (let's say fairly quickly and without much warning ). I have a couple questions and they're kind of similar so I'll post them up. I've read docs about regex and creating them both via command line and ASDM, but the examples always seem to include info I don't need or honestly something I don't understand yet (mainly related to defining classinspect maps). If someone could provide a simple example of how to do these in ASDM that would be useful in understanding how regular expressions are properly configured. So here we go.
I know this is basic but I need to make sure I understand this properly - I have a single web server (so this won't be a global policy) where I need to allow access to a specific URL pathfile and that's it. So we'll call it est estfile.doc. Any other access to any other path should be dropped. What's the best way to do this in ASDM (6.4)? I think if I saw a basic example for this I could figure out next few questions but I'll post them as well just in case.
I have another single public web server (again this won't be a global policy) where I'd like to specify blocking file types, like .php, .exe., etc... again a basic example would be great.
Lastly, and this is kind of related, but we have a single office/domain and sometimes we get spam from forged addresses appearing to be from our domain. On Checkpoint I used to use its built-in SMTP security server and could define if it received mail from *@mydomain.com to drop it because we would never receive mail externally from our own domain name. I saw something similar with ESMTP in ASDM and it looks kind of like how you set up the URL access mentioned above. Can I configure this in ASDM as well, and if so how?
I have deployed a cisco 2504 wireless controller along with four (04) lightweight access points (1041N) in four floors respectivly. The clients connect to the AP which is deployed in the lowest floor have regular timeouts/packet drops. Further this particular ap operates at channel 11 and it has around 11-13 rough access points in the same area and operates in channels such as 1,3,6,9,11. The DCA (dynamic channel allocation) is set to auto in the WLC. Further each ap has maximum of 07 -10 clients at any given time and I have changed this particular ap and checked still the result is same hence there is nothing wrong with the ap.
View 1 Replies View RelatedI just got the WRT610N and I really like it so far, I'm playing with the NAS option and I can't get it to create any new users or groups. I click on the link, fill out the form and click on 'modify user' (The set-up guide has a button there for 'save settings') and nothing gets created. I tried this several times and there are no new groups or users. I checked the storage.info file and there is no additional users or groups there either. I think I can edit that file but I'm not too sure what these last 2 lines mean
nas_login@admin:admin:admin: off guest:guest:guest: onusers_content@admin:admin:admin:admin: off guest:guest:guest:guest: on