Cisco Routers :: RV180W Worthless With Current Firmware?
Feb 3, 2013
Having just installed a new RV180W router for a customer last week, I am beginning to regret my decision to to go with this model. Issues are as follows:
1. Users connecting via VPN can not browse web or receive email until the disconnect from the VPN.
2. Internal users experiencing very slow web site access and page lockups (speed test shows a good 15MB connection rate)
3. No clear setup for an isolated 'guest' WiFi network.
All of this happened as soon as I replaced the old, stable RV042 with the new RV180W.
View 1 Replies
ADVERTISEMENT
Mar 19, 2013
i've installed the new firmware on my router and now the UC is showing 100% all the time. I've tried to factory reset it, it's doing the same thing. If I downgrade to previous firmware, it goes back to normal . I've only 1 PC in my network (test lab), so no big traffic here. is it a bug ?
View 1 Replies
View Related
Mar 11, 2013
need The Firmware for the device....URL
View 5 Replies
View Related
Jun 5, 2012
I am trying to download firmware for an RV180W Wireless-N Multifunction VPN Firewall Router. I found updates for a 110 in BIN format (router only updates from IMG). Currently running stock firmware on that router and need the update.
View 2 Replies
View Related
Mar 12, 2013
Today I installed the 1.0.2.6 Firmware on a RV180W. I only have now two problems regarding the Static DHCP support in the GUI.
1. Via the Networking > LAN (Local Network) > Static DHCP I have no buttons to Add a new static Lease.
2. Via the Networking > LAN (Local Network) > DHCP Lease Clients I can thick a Lease and click on Make Static IP. The result is an error: Operation failed.
View 3 Replies
View Related
Apr 21, 2013
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
View 3 Replies
View Related
Dec 15, 2012
I would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
View 9 Replies
View Related
Jul 17, 2011
I would upgrade the firmware before deciding to replace router with a new one. I noticed there have been several updates to the firmware since I originally installed the router with the current available firmware version of 1.35NA.
View 12 Replies
View Related
May 1, 2011
I tried to update my firmware on my DIR 615 by clicking the check now button within the routers parameters and got the file DIR615C1_FW311NAB04.bin The update bombed. I have hardware ver. C1 Firmware ver. 3.11NA dated June 23, 2009.Should I try and install the other firmwares in subsequent order, i.e. ver 3.11NA (dated 7/15/2009), then ver. 3.12 and then ver. 3.13 Or should the latest and greatest cover them all?
dwest.Wireless to router. No factory reset. ISP Ser. Cable ISP Router. Stand Alone.Modem Make & Model. I have to get up for that one, will have to report back tomorrow.
View 4 Replies
View Related
Jan 23, 2011
I have what I believe is an original (V1) version of the BEFSR41 gateway/router. The label underneath the device only shows the model number with no version information. Current firmware version on the device is 1.46.02, dated Aug 03 2004.
Can I confirm (1) that I indeed this router is at hardware version 1? If that is the case it appears from your web site that version 1.46.02 is in fact the current and only firmware version for the device and that there are no firmware version upgrades available.
The DHCP software current does not have IP address reservation, which I am interested in adding if possible via firmware upgrade. If not then I have to consider whether I want this feature bad enough to replace the router.
View 4 Replies
View Related
Mar 17, 2013
I just purchased a RV180W wireless router. It came with 1.0.0.30 firmware revision installed.
I have tried from multiple computers and multiple browsers to update the firmware on this unit, and I always end up with the same result.
"Firmware file is invalid or corrupted"
I have also downloaded the images (1.0.1.9 and 1.0.2.6) from multiple machines all with the same result.
View 2 Replies
View Related
Jan 1, 2013
I start this topic for may an answer as i face a problem with VPN and most likely with PORTS.
My firmware was 1.0.0.30 and i Update it to 1.0.1.9.
When i was try to connect with my VPN i am unable to reach it with error 800. MS says your firmware is too old so you get this error.
At the same time for VNC and some other stafs was necessary to open ports. Until now it seems that the router is not opening the ports.
What i should do? Return to the old firmware? Any extremely changes at new firmware so they had add more options for the ports? All the configuration is exactly the same as it was before the upgrade.
View 3 Replies
View Related
Feb 7, 2013
I've just bought a Cisco RV180W and I am trying to find its newest firmware but I am getting 404 everytime I access or search for this updates.
View 1 Replies
View Related
Dec 24, 2012
I need to reset the channel on my N300 router but in order to do so, I need to log in. The log in screen does not take my existing password. How do I get my current password or reset my password? It should be the simplest thing, but I have found this to be extremely difficult with Belkin.
View 1 Replies
View Related
Mar 15, 2013
I installed the RV180W yesterday and decided to play with it a bit today. I got stuck on the firmware update. Tried different browsers on different PC's. Tried going to 1.0.1.9 first. I have the "reset all configurations" button checked. After looking through the posts here I'm not sure this firmware will even fix my next few problems(port forwarding etc). Is there a trick with this device?
View 4 Replies
View Related
Feb 5, 2013
I'm trying to make the VPN connection between two routers CISCO RV180w.I performed the basic configuration in cisco "server". I did the same in cisco "client".The following configuration and logs, do not know what to do ...
SERVER CONFIGURATION:
IKE Policy Configuration:
VPN Policy Configuration:
CLIENT CONFIGURATION:
[code]....
View 8 Replies
View Related
Apr 9, 2013
We have installed a fiber internet access and have the ONT from the provider already installed.We're trying to use the RV180W to use this internet connection. [code] So I need to configure the router with the .36 static IP on the WAN, and using the .37 gateway and the provided DNS servers. I also need that this WAN is tagged with VLAN ID 20. I'm only able to set VLAN ID on the LAN ports via the admin interface.
View 8 Replies
View Related
Jul 25, 2012
I am struggling to configure my new RV180w router to accept a VPN connection from my Apple computers.
I wish to use IPSec with Group and Pre-Shared Key authentication. The RV180 has just replaced my 800 series ADSL router and I want my remote clients to be able to connect using either the VPN client capability built into the OS X operating system or the Cisco VPN Client software installed on their Macs.
So far, using the RV180's web setup screens, I have created a VPN Policy and a corresponding IKE Policy was created as well. I couldn't see anywhere to include the 'Group' name. I have created a user but wasn't sure of which Protocol to use so I am trying XAUTH.
At the client end some people are connecting using Cisco's VPN Client software Download Software - Cisco Systems
Some people, with OS X 10.6 and above, are using the Mac OS X network built-in VPN client.
We all connected without a problem to the previous 800 series router using IPSec with Group authentication and Pre-Shared key.
View 5 Replies
View Related
Sep 12, 2006
Is there any commands to know the Current Heat Dissipation of high end routers and switches 7600,6500? Even though we can calculate thro. corresponding calculators, i eager to know is there any commands to do that?
View 4 Replies
View Related
Oct 3, 2012
I just recently switched from the WRVS4400N to the RV180W. I have 4 VLANs, and I want VLANs 1, 2, 3 to communciate freely, but I DONT want VLAN 4 to communicate with anybody, just Internet access. On the WRVS4400N, I was able to do this using the Firewall > IP Based ACL. I notcied that the RV180W, does not have such an option. I am sure there is something I am missing, I just cant find out how to isolate VLAN 4.
View 5 Replies
View Related
Sep 6, 2012
we've changed our rv042 for a rv180w and now when I try to upload files to my ftp server (vsftpd under centos) it get stuck at 100%.I've changed my ftp server to proftpd instead of vsftpd and everything's ok.but vsftpd isn't the problem since i was able to upload with my rv042 without any problems.so i guess there's a problem with the rv180w security.i've already disable stealth mode and it's doing the same thing when i try to upload to the same server but through the vpn tunnel, everything's ok.So it's really in the rv180w lan->wan routing
View 10 Replies
View Related
Aug 13, 2012
Have not purchased RV180W at this time, therefore have not read manual. Need for small office, 2 VPN logins max & not 24x7 use. What VPN client software ? (using Win7-64bit laptops)
I did notice software called Quick VPN Client 1.4.2.1 for download.
Does buying RV180W allow download of Cisco Systems VPN Client software ?
View 2 Replies
View Related
Feb 18, 2013
I am located in UK which uses PPoA for ADSL broadband. I use a DrayTek Vigor120 ADSL2 Modem to act as an ADSL bridge and PPoA to PPPoE converter. This passes the ADSL authentication requirement (and subsequent single static IP address) to the Cisco Small Business RV180W sitting behind the Draytek. However, the RV180 (Firmware Version 1.0.0.30) cannot form the PPPoE connection. I have tested the modem, adsl username and password by creating a PPPoE interface on my computer and connecting this directly to the Draytek modem. The computer receives the expected IP address and I can ping remote public IPs. I have entered the username and password into the PPPoE profile,
Authentication type: CHAP (confirmed by ISP but I have also tried all other options just in case).
Connection Type: Keep Connected.
MTU Size: 1400 (also tried default, which worked OK on computer interface).
MAC Address Source: Use Default (I have successfully used combined modem/router so a "fixed" MAC address is not required).
View 3 Replies
View Related
May 21, 2013
I live in China. I want all of my PC's and devices to connect through the RV180W VPN Router to a VPN provider in the US so that all of my traffic is encrypted and appears to have a US IP address. I need to find a VPN Service Provider that supports the RV180W and how to configure it. I don't want to configure every PC and device, I just want them to use the VPN conneciton at the router.
View 3 Replies
View Related
Apr 11, 2013
I am using DynDNS in lieu of a static ip. My ISP changed my WAN ip last night as expected however the RV180W did not update the WAN ip, and so the router is now offline. Using a secondary internet connection I have logged into DynDNS.com and checked my hosts file and confirmed the ipa has not updated since March. I changed the update period from 360 to 2 so this never happens again, but I need to now change the WAN ipa in the RV180W to match the new one. I remember a screen that shows the current WAN ip address greyed out under the present one, but I dont recll where to go to get to that. I am at a loss as to where I go in the RV180W to change the WAN ip address.
View 1 Replies
View Related
Dec 9, 2012
We are deploying over 20 RV180W Routers for a client and need to find a faster way to configure them for shipping.We have created a base image (all settings that will be shared between the 20 locations), we need an easy and quick way to make IP changes for the 3 VLANs and Local Security Groups for the IPSEC VPN.I tried to edit the CFG file by hand, but the checksum fails when it is loaded into the RV180W.How can I accomplish this? Can I manually create the checksum?Can I remove the checksum?
View 3 Replies
View Related
Oct 9, 2012
Comcast has indicated that this is required for IPv6 to work, and since it means gatting a /64 address space for my network I am understandably eager to tak advantage of this new functionality when it is available in my area.
View 44 Replies
View Related
May 2, 2012
I am wanting to purchase the RV180W for a small Optometrist office. We are beginning our transition to EHR and what to ensure the RV180W is HIPAA compliant and if not what would be the next best product for about the same price?
View 2 Replies
View Related
Sep 10, 2012
I have rv180w (firmware 1.0.1.9) and 1 Gbit/s internet.When i turn on WAN Traffic meter, WAN speed down to 100mbit/s.I didn't find any suggestions in official documentation.Is this a bug or undocumented feature?
View 2 Replies
View Related
May 16, 2013
Our company own a RV180W router. It works well with firmware 1.0.1.9 but with firmware 1.0.2.6 it is impossible to SSH between our devices. Ping still works though.
View 1 Replies
View Related
Oct 10, 2012
I have the followint setup:
VLAN1 = 10.1.10.1
VLAN2 = 10.1.11.1
Inter WLAN routing is enabled on both VLANS
I have VPN PPTP set to 10.1.10.50-60
When I connect the VPN I get an IP address of 10.1.10.55 I can ping the 10.1.10.x network i cannot ping anything in the 10.1.11.x network.
I need to be able to see (ping/access by IP) both VLANs from a VPN PPTP connection.
View 2 Replies
View Related
Dec 4, 2012
I can't seem to satisfy with the RV180W. I've set a firewall block rule for certain traffice lan>wan, and I'd like to view the log.
Administratration | Firewall | Firewall Logs, I can select any or all items. Where do I view the log?
I can go to Logging | Logging Policies and select everything for the 'default' policy.
No matter what, I go to Status | View Logs, and select whatever severity level I want but get little to nothing, and definitely no firewall logging.
View 9 Replies
View Related
Aug 30, 2012
There are 6 part numbers for the RV180W router. What is the difference between them: wan access (Annex A,B ...) or other quality?
View 1 Replies
View Related
