So I went to update the firmware on my SA520 last night and aparently something failed, the device restarted and now it doesn't respond to anything. The Diag light stays light and the factory reset button does nothing no matter how long I hold it in. Is there another way to reset the device?
View 2 RepliesWhat do I do if my routers light stays amber and wont turn blue? The wifi is not working because of this even though it is saying the signal strength is excellent and I have already done the reset a bunch of times its been two days and I just cant get it to work. Its the N300 router
View 2 Replies View RelatedAfter a few months of trouble-free ... the Cisco WRVS4400N V2 stopped working. i have tried to reset by holding the reset button for 30 seconds ... but nothing changes the red DIAG light remains on at all times
i have also tried two different versions of the Firmware Rescue Utility but all i get is "unable to scan"
I have been given the task of unbricking a WRVS4400N V2 router. It just sits there with the Power and Diag lights blinking and does nothing else.I'm thinking I'm going to have to try to find some way to flash the firmware, because I'm seeing that this is a common problem with this router.I already tried support "chat" online, but after about 20-30 minutes waiting for someone to actually come into the chat room, I gave up.I did note that this model is not being sold anymore and won't be supported before very long, so this may be a gigantic waste of time, but I thought I would give it a shot.
View 2 Replies View RelatedI am currently trying to configure a Remote Access VPN on a SA520 (Primary Firmware Version 2.1.51) using Cisco VPN Client (Ver 5.0.07.0410)
Until now i have connectivity from the SA to the LAN and i can connect using the Cisco VPN Client to the AS:
[IKE] INFO: IPsec-SA established[UDP encap 12856->4500]
[IKE] INFO: IPsec-SA established[UDP encap 12856->4500]
It gives me an IP from the pool but i can not reach through ping to my LAN.
I am trying to configure the DMZ on my SA520 router but without success.After a lot of tests I reduced everything to a very simple test case that is not working: I setted the "Optional Port Mode" to "DMZ" and enabled "DHCP Server" in the "DMZ Configuration", but DHCP on the DMZ does not assign any address.I am wondering if my optional port is broken or not.
View 4 Replies View RelatedTwo factor setup with Symantec VIP? I just fined setting it up and VIP Service and SA520 seems to be synchronizing correctly but device doesnt direct VPN users for second authentication ?
View 16 Replies View RelatedI have a fibre connection on the dedicated WAN which was working perfect until someone somewhere cut through the line. The SA520 fell over to the Optional WAN port which is basic ADSL line which is connected. Logmein client is online too.
But it refuses to browse webpages, appears to be a dns issue or firewall or both.
I have added the ISP dns addresses into the forwarders on my server.
We have Cisco SA520 and we want to use VPN to access the office servers from home. We have been able to configure the VPN server on the SA520 however the connection is very unstable.We use OS X 10.7 lion built-in Cisco compatible VPN clients and this is a typical output of ping from 3G mobile network to a server inside the office network. It works the same way also if I am trying to access from my home ADSL connection so the problem is not the instability of the 3G connection.
Some sample traffic sequeezed:
PING ns.svm (192.168.60.27): 56 data bytes
64 bytes from 192.168.60.27: icmp_seq=0 ttl=63 time=98.022 ms
64 bytes from 192.168.60.27: icmp_seq=1 ttl=63 time=76.934 ms
64 bytes from 192.168.60.27: icmp_seq=2 ttl=63 time=278.201 ms
[code]....
We have a Cisco SA520 Router (Firmware 2.1.18)We are only using this for about 1 month now. Router seems ok its justI am worried about the Memory utilization which reach to 62% (144/234 MB)Is this something to worry about?How can I utilize this by lowering down the usage?
View 3 Replies View RelatedI have an SA520 setup and all my users can login to the SSL VPN tunnel except one user. The laptop is running windows 7 64bit and had IE9 installed. When I try to connect her to use an SSL VPN Tunnel, I get the following error: Cisco-SSLVPN-Tunnel Install Failed: Error in getting proxy settings!. I have made sure the firewall was turned off. How to get the ssl tunnel connected?
View 3 Replies View RelatedIs PVID the same thing as "native vlan"? Can the native VLAN be changed on a SA520? Currently I believe it to be 1, I'd like to change the native VLAN to 10.
I have a scenario where I have a prexisting production LAN of 192.168.1.0/24 . It's a small organization (a church), but they purchased 3 Aironet 1130ag units. They want to have a "private" WLAN that is part of 192.168.1.0/24 , and a guest WLAN of a different subnet (I chose 192.168.20.0/24) . The two should never meet. There will likely never be a guest computer connected via ethernet. Guest computers would always have to connect wirelessly.
I left VLAN 1 on the SA520 192.168.75.0/24 subnet as default.I created a VLAN 10 , 192.168.1.0/24 subnet, and I created a VLAN 20, 192.168.20.0/24 subnet.Ports 1-3 of the SA520 are members of VLAN 1, 10, and 20 (cannot remove membership of VLAN1, which is pretty annoying).
Both are secured by WPA, and when I connect, the proper DHCP subnet passes from the firewall through to the wireless client, for each respective SSID.Ultimately, I'd like the SBS 2003 server to handle DHCP for VLAN 10, and have the SA520 handle DHCP for VLAN 20, but i'll take what I can get.
The original production LAN is connected via an unmanged switch.I'd like to trunk the unmanaged switch to Port 4 on the SA520. However, since the PVID (native vlan?) of SA520 is 1, and I cannot make Port 4 on the SA520 ony a member of VLAN 10, then anything traffic coming from the unanaged switch will automatically be tagged with VLAN1, correct? Thus causing the already existing production network to start receiving DHCP from the firewall in the 192.168.75.0/24 range.
How could i make a vpn tunnel between a router SA520 and a central UC540.
View 3 Replies View RelatedIs there a way on the security appliance SA520 to remove someone from the DHCP lease client manually rather than setting the DHCP lease time to expire in less time like 4 hours or 2 hours. I was able to do this on other routers by highlighting the connected device and click remove. If not any recommendations on how to handle the device that are attached via DHCP and the person is no longer here, but the lease time is not up. I have set DHCP lease time to 4 hours.
View 1 Replies View RelatedIs it possible to re-route our Site 2 Site VPN over our Static Route (T1) if the WAN fails?
View 1 Replies View RelatedI am unable to isolate DMZ and LAN traffic with an SA520 running 2.1.7.1 firmware. I have the optional port configured as DMZ and DHCP server enabled. I tired leaving the firewall as default. Also tried creating firewall rules to deny traffic from LAN to DMZ and DMZ to LAN for any address and any service.I am still able to ping devices both from LAN to DMZ and DMZ to LAN. I am also able to see network resources in both directions.
View 5 Replies View RelatedI have several sa520 appliances, and one of them came with the 2.1.72 firmware and it works perfect... with all others I upgrade to 2.1.71 (because I was not able to find 2.1.72) that is the latest posted in the CISCO download area.So, is there any way to get 2.1.72 ?With the 2.1.71 the VPN Site 2 Site works fine some time, but later it disconnect and it does not connect until I disable /enable the VPN.
View 2 Replies View RelatedAfter inserting a RSP720-3C-10GE in module 6 and running the show module command display the following [code]what is the meaning of the UnKnown on the oline diag status ?
View 1 Replies View RelatedWe recently installed a WS-X6716-10GE module in slot 6 within a Cisco 6506. We are using two ports on the module (6/13 and 6/14), which are port channeled together to a Nexus 5548. Everything has been running fine for about a month and the card had a green light but the ports stopped communicating. The module was screwed into the chassis/slot. For problem determination reasons, we reconfigured ports 6/13 & 6/14 to 6/15 & 6/16 and moved the cables but the module was still not responding. We eventually pulled the module out of the slot and reinserted the module back into the slot, which reset the module and fixed the problem. Is there any way to determine if this was hardware problem with the module and it should be replaced, or is it a software bug/problem? We opened up a ticket with the TAC but we haven't heard back from them yet.
Cisco WS-C6506-E
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-M), Version 12.2(33)SXI8, RELEASE SOFTWARE (fc2)
Mod Ports Card Type Model
--- ----- -------------------------------------- ------------------
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B
6 16 CEF720 16 port 10GE WS-X6716-10GE
[code]....
Is it possible to reflash the firmware on a BEFW11S4 (I believe v1, there is no v# after the model number) with a solid red Diag LED? I cannot access the HTML control panel since the router never fully boots. I git this used and didn't know it was **bleep**..
View 2 Replies View RelatedI previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!
View 1 Replies View Relatedmy belkin G F5D7234-4 router internet light won't come on??
View 1 Replies View RelatedWe have a Cisco SRP 527W router that was not showing up on the LAN. so we tried a Factory Default reset but it seems to be dead.
The power light is flashing constantly,the 4 LAN light are constantly on,the DSL Data light comes on for 1 sec when device is powered up.
i have tried connecting directly to a PC, the NIC reports as network cable unplugged.i have tried the (power on device, hold down reset button, power of after 30 sec, power on after 5 sec, release reset button after 5 sec) but still "network cable unplugged".
the firmware flash utility will not find the NIC the device is connected to.the router is less than a year old, is there a fix or is it a warranty replacement ?
my DSL light is blinking at evening around 6:30 evening every day.
View 1 Replies View Relatedthe router is functional, however the green light has never blinked like it is now.
View 1 Replies View RelatedI was having problems connecting to one of my usb devices that was plugged into my router. I unplugged the router to reset it and whenever it starts up it flashes green and the green light goes solid for less then a minute before turning red. It's a solid red light. I've tried unplugging everything and restarting it and nothing. Ironically it still lets me connect to the internet but when I access the control panel on my computer it shows as disconnected. Is this means my router is busted. This is my second Belkin Router and the only reason I had to replace the last one is because it was a G+Mimi router and I upgraded to an N Router.
View 3 Replies View RelatedPrinter (Brother DPC-150) used to work with Belkin router. After a power cut printer works and router seems to work - on their own. But when I plug printer into USB slot on Belkin the little green light does not come on.
View 1 Replies View RelatedI am trying to light up every port light on a 3750g. There is not anything plugged into them and I would like to know (just for fun) is there a way to make every port light 1 - 48 turn on using a command?
View 3 Replies View RelatedBelkin wireless n300 router has an orange light. All of the cables are plugged in and have tried ipconfig?
View 1 Replies View RelatedMy N600 router has a flashing orange light on it. What's going on with this thing?
View 4 Replies View RelatedWe just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
View 2 Replies View Relatedhad a firmware update error model WNR3500
View 1 Replies View RelatedOn Page 16 of my N600 DB manual it says that below the "Router Status Light" and above the "WPS" letters there is a "Wi-Fi Protected Setup (WPS) Light and Button". When I look at my router all I see in this space is a raised rectangular plastic strip. Should I have a light and button there?
View 1 Replies View Related