I need to estimate the installation and configuration time of Cisco NAC (NAC Network Module spare for 2800, 3800 ISR) and Cisco NAC Manager(NAC Appliance 3315 Manager -max 3 Servers. There is some Cisco tool to estimate the installation and configuration time?
View 3 RepliesWhat is the installation time for the Network Processor engine is:
NPE-G2=7200 series NPE-G2 engine with 3 GE/FE/E ports ,Do you reckon it can be done in two hours?
As part of a DC deploy, aI have to install 2 x ASA5580. My surprise was the missing connection bolts (or place) on the chassis for the grounding cable. All othes equipments (ASR, 6500, Nexus 7K) have a grounding connection on their chassis.
The Installation manual alerts and requests a good gorundid for it. But where should I put it??Note that the rack where it's installed on is already grounded.
Does the E1000 router come with a default security setting upon installation using the supplied CD?
View 9 Replies View RelatedI am using an 831 router and am trying to get DDNS to work. Here is the debug output:
RESS_ASSIGN: Interface Ethernet1 assigned DHCP address 67.162.204.242, mask 255.255.254.0, hostname testlab831.xxxxxx.com
00:53:06: DYNDNSUPD: Adding DNS mapping for testlab831.xxxxxxxx.com <=> 67.162.204.242
00:53:06: DYNDNSUPD: Sleeping for 3 seconds waiting for interface Ethernet1 configuration to settle
00:53:09: HTTPDNS: Update add called for testlab831.xxxxxxxx.com <=> 67.162.204.242
00:53:09: HTTPDNS: Update called for testlab831.xxxxxxxx.com <=> 67.162.204.242
[code]....
what the problem is with the "Call returned Connection time out for update testlab831.xxxxxx.com <=>" line.
Can AVG and MSEssentials be running at the same time?
View 4 Replies View Related4402 Wireless LAN Controller running 7.0.116.0 versión. The equipment is working fine, but after a hard reset i lost date and time configuration.No other configuration is affected, only date and time. What can be the cause of this?
View 18 Replies View RelatedI have been working on my ASA 5510 version 8.2(1) trying to change the maximum connection time. Originally the custom "Group Policy" for IPSEC (Remote Access VPN) was set to inherit the settings from the default system Group Policy (DfltGrpPolicy). The custom group policy for the sake of this discussion is called "ABCD". I have modified the settings on the default (DfltGrpPolicy) as the custom policy (ABCD) was inheriting the configuration from default to disconnect after 1200 minutes. I changed the setting "maximum connection time" to 1200 minutes. I saved the configuration and what not then connected my VPN client, after two (2) hours I was disconnected. Something just doesn't add up.
I went ahead and deselected all inherited properties and manually configured them for the ABCD custom policy. No longer was the ABCD custom policy configured to use the inherited properties/settings. I saved the configuration again tested but instead of having a 1200 minute connection limit, I have 120 minute connection limit. Inside Monitoring --> VPN --> Sesssions : I can click on my session and see Session details". The Group Policy and Connection Profile properly list the "ABCD" custom profile. However, the "Conn Time Out" setting is: 120 minutes. I am completely stumped as to what is going on.
In the actual running config I see:
group-policy abcd attributes
banner none
wins-server value 123.123.123.123
dns-server value 123.123.123.123
dhcp-network-scope none
vpn-access-hours none
vpn-simultaneous-logins 3
vpn-idle-timeout 60
vpn-session-timeout 1200
What I need to do next to get this working short of a recycle of the ASA.
We have ASA running code 8.0.4 with Active/Standby for quite long time. Today when we gave the command wri standby it started sync the config to standby ASA but waited forever.when we checked the show failover, we got the following result.
This host: Secondary - Active
Active time: 1928633 (sec)
slot 0: ASA5540 hw/sw rev (2.0/8.0(4)) status (Up Sys)
Interface PERIMETER-MGMT (10.12.8.1): Normal (Not-Monitored)
Interface OUTSIDE (86.36.xx.xx): Normal (Waiting)
[code].....
When we console to Standby ASA and tried to save (wri mem), we got the following error and also please note the hostname has become default...?
ciscoasa(config)# wri memory
Building configuration...
Command Ignored, Configuration in progress...
[FAILED]
and when we tried to give following command we got this error:
ciscoasa(config)# copy running-config startup-config
Source filename [running-config]?
%Error reading system:/running-config (Configuration temporarily locked)
ciscoasa(config)#
I see here the standby ASA IPS module is down, but can that issue cause not sync the config backup and writing to nvram (save config)..?
So, I have this router at home a WRT150N. I put in access restrictions so my siblings won't stray onto unwanted pages.I enabled SPI Firewall Protection and what do you know, it worked. The next day though, we didn't have an internet connection.I checked everything with the modem (power cycles, etc.) and then I tried the router. Upon disabling SPI Firewall Protection, the internet connection came back.I tested it yet again, to see if it really was the SPI. Enabled and bam, no internet access again. I made sure to select "Allow" in the Access Restrictions for "Internet access during selected days and hours" making sure also that "Everyday" and "24 Hours" are selected.Now my question is, what do I need to do in order to enable my Access Restrictions without having to lose internet connection via the SPI Firewall?
View 2 Replies View RelatedMy site got the NAC-3315 appliance and we would like to reimage this appliance to inline posture mode (for VPN purpose)What's the proper migration process should deal with this? Is the NAC-3315 hardware comply with the Inline posture mode requirement?
View 4 Replies View RelatedI installed ise-1.1.1.268.i386.iso on a scratch to the new NAC 3315. As i check cisco download mentioned it need to patch following files :ise-patchbundle-1.1.1.268-1-60802.i386.tar.gz,But once try to patch it show like attachment message, is it mean that i no need to do the patching?Or is there any instruction need to remove and reinstall for this files.
View 4 Replies View RelatedIs it possible to add another NIC to the Cisco 3315 NAC appliance. It ships with Four ethernet interfaces, but would like to add at least 1 extra interface i.e. PCI card if possible.
View 1 Replies View RelatedI have a network with static routes witch I need to convert to OSPF.Never used OSPF, and do not have much experience in routing in general.The netvork is connected via some fiber links, but moastly wireless bridges.I have attached a drawing of how the network is.Routers are 3550, 3560 and 3750s.Each router is on a different physical site.
View 2 Replies View RelatedWe have insatalled 5 ise 3315 boxes IOS 1.0.4 in our network where in two of them are admin node , two of policy services and one is mnt node. We are using guest sponsor portal for wirless guest user where in we have integrated WLC 5508 with ise and using weblogin for guest users.
We have created open ssid in wlc and using external redirected url of ise for guest login page. But when we create any guest user in sponsor login for guest user we faced following issue
1) When guest user gets conected to wirless and login in to guest portal with credential after putting credential then its again redirect to same login page wihout successful login prompt.
Can we pompt successful login after guest login to guest portal or redirect to any other link like google.com so guest user will gets to know he is able to access internet now
2) We have creted time profile 8hours first login for guest user. When guest user gets connected while putting credential in to guest portal. But we face issue after approximately every 20 mins guest gets disconnected from internet and guest again gets login page of guest portal and if we put same credential then its working but after approx 20 min interval user get disconnected from internet.
I got a ISE 3315 with an IP-Plus license on it. Now I need to install a Wireless advanced license, but I got an error when trying. I've read that the wireless license doesn't need the ip-base one but I can't remove it?
View 1 Replies View RelatedI have a nac guest server 3315 appliance with 4 NICs. I want to connect each NIC to 4 different networks without allowing traffic between them. So RADIUS interface will be different from sponsor/admin interface to the NGS. how to achieve this. I have created and assigned a static IP address using system-config-network, but when i do ifconfig i dont see the remaining 3 NICs and the web interface doesnt seem to have provision to create this interfaces.
View 3 Replies View Relatedwe have a new ISE 3315 installation going on, I powered on the Appliance and appliance booted sucessfully, I run the Setup command. however after Setup is completed and appliance got a reload, it is not booting at all , booting seems to be hang up as per the snapshot attached.however Appliance is pingable, . i carried the following tasks as part of troubleshooting.
2: suspecting that Setup was corrupted, i then re-initialzied / re-installed the ISE Completely, then i run the setup command and after self reload, exactly same behaviour.
3: I tried with both Secure CRT & Putty and results are same
Whether ISE-3315-K9 with ise version: Service Engine: 1.0.4.573 , supports the command level accounting
Bascially , we have integrated Cisco Switches with Cisco ISE for Device Authentication using Radius , we are able get the authentication logs on to the devices , but for any command changes or update done on Cisco devices we are not able to get the command accounting.
We are conduction a Proof Of Concept (PoC) on Secure Bring Your Own Device ( BYOD ) using Cisco ISE and gonna test all the scenarios like Wired, Wireless and VPN user access.
Our Setup has ISE VM acting as Admin, Monitor and Profiling Device, we have NAC 3315 physical Appliance as Inline posture Device, Wireless LAN controller, Access point and the Identity source as Microsof Active Directory.Having Plans to Integrate Mobile Device Management ( MDM ) and Citrix VDI setup also.
As of now we have tested the Wired Scenario Authentication and authorization for guest users and gonna carry out the profiling and posture.
-MDM can be integrated to ISE ?
-How the MDM can be integrated to Cisco ISE configuration or Guide to show the same?
-What is the demarcation between MDM and ISE ( i.e. What is the role of ISE and MDM on Mobile Devices ) ?
-If MDM is available so then when the control of ISE ends, does MDM do management or ISE will do management of the devices ?
-Is MDM will do client provisioning or ISE should do ?
-Is MDM send or update patches of Mobile Devices ?
my ISE 3315 is stuck in ISE 3315 stuck in INIT Entering runlevel: 3 when i connect a screen and keyboard i can only see this last message : ISE 3315 stuck in INIT Entering runlevel: 3 There is nothing after, i cannot login (no prompt) even after waiting 20 minutes with this message
I have no char return via serial cable depsite i was able to run initial setup from console (same cable, the DB9-DB9 provided, same serial config, same laptop)
Version ADE : ADE-OS-2.0 (2.6.18-238.1.1.el5PAE)
Version ISE : 1.1.0.665
I would like to ask, given that i got 2 units of ISE-3315 appliance, one need to be primary node for admin-policy service-monitoring, another unit then become Inline posture node.For the preparation on line posture node, what shoud i do on it?
01. For the unit ready to become inline posture node, so I just boot it, install the OS from sractch (using version 1.1.1), then start the initialize setup etc, like Normal setup?
02. Before i regieter, what is the deployment nodes i should select for inline posture node unit? provided the admin-policy service-monitoring will become primary node, and registration for inline posture node will be next action.
We want to buy a ISE-3315-K9 for 500 end-devices.In the price-list I found the ISE-3315-K9 but cannot find the base license: L-ISE-BSE-500=. (I think I need this license)Will the shipment of the ISE-3315-K9 includes a 3000 end-points base license (maximum support of the ISE-3315) or do I need to order the base 500 license seperately?
View 1 Replies View RelatedI try to configure PGM in my 2911 plattform but it was impossible. I tried with many 15.1 version that support this protocol.
Someone configured PGM over 2911 Routers? What does correct IOS for work?
Our client ( a webhost, they have a lot of servers ) has a an older Cisco Pix, everything works fine with the PIX. They have a Cisco ASA 5500 with ASA version 8.3 , to replace the PIX. Upon migrating the PIX config to the ASA we are running into issues with Dynamic NAT. The static NAT entries are working flawlessly (there is a lot of them), however when Dynamic is enabled for the remainging hosts, outside communication works then drops off. The remaining hosts need outside access for updates. We have access lists set up but I dont se ehow that could cause a problem when the original ACL's were working fine with the PIX, they have not been altered.
The NAT config may be wrong or cluttered, have a look at the full NAT config.
The static NAT addressing is the same, example 207.11.129.65 will equal 10.10.10.65
saw that we can secure ripv2 via authentication (simple and MD5) ,i undertand that simple is not quite secure because we can see the plain text when capturing RIP packets
however even with MD5 i can see the authentication data (output of MD5) and i think hacker can copy it and paste it in one RIP packet that he will generate !! isn't it ? so how much MD5 is secure ?
I was given a 510 PIX Ver 6.3(1)to reconfigure but have no information on the existing configuration and need to wipe it clean and start over how can I do this to get back to the factory default settings. I have tried the "monitor>" but I don't know the IP address of the PIX interface.and am not sure how to do the setup for recovering the password.
View 7 Replies View RelatedWe have had an ASA5505 for close to two years. About a year ago, we added a second ISP ("BOB") which became our primary and our old one (SBC) became our backup. I successfully modified the config for this and it's been working well.
Now we're changing our primary ISP to Comcast and getting rid of BOB, so right now we actually have 3 ISPs coming into our building.
I removed the BOB interface and routes, then added an interface for Comcast using an IP address from the range they provided as well as a static route to the gateway they provided - everything is analagous to the previous interfaces and routes, but it doesn't work. If I physically disconnect the Ethernet cable going to the Comcast cable modem, then the ASA does fail back to the SBC interface as expected. If I put the BOB interface & route back in there, it works again through BOB.
If I connect a PC to the Comcast cable modem and use an IP/Gateway they provided, the Internet connection *does* work. Using this same exact IP info in the ASA doesn't work.
Is there some other configuration item besides interfaces and static routes that I should be modifying? Is there some way I can dig deeper into the ASA to see exactly what is failing?
I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.. then what i do is a copy start run to get the configuration active..
View 2 Replies View RelatedI have got a working 5505 running 8.3.1 firmware and 6.3.1 ASDM.I have now purchased a second unit and ensured that both units are running the same firmware levels etc.
I have via the ASDM created a backup of the working units configuration, and now i want to load this configuration onto the second unit.I have connected the consiole cable up to the second unit and tried pasting in the contents of the configuration file but no joy.I want to ensure that my configuration will work on this unit before i configure the two units in Active/Passiove configuration.
I used my Pix config to setup the ASA 5505.Everything seems to be right. I used ASDM to view settings and it seems right. I am missing something minor, but I am going blind looking at it.
I can remote into the network from outside, but internatlly I cannot get out of network. No internet or email is passing through.
: Saved
:
ASA Version 8.2(5)
!
hostname textasa
domain-name testcorp.com
enable password 579oWRzSY5syo9yt encrypted
passwd 579oWRzSY5syo9yt encrypted
[code]....
i hav asa5520 i copying configuration from PIX to ASA5520 (7.2) everything working fine bt problem is that after sometime my DMZ interface losing connectivity ...
View 1 Replies View RelatedHow to set upo configuration & Security after reset
View 2 Replies View Related