Cisco Switches :: SG200-26 How To Configure Fast NFS File Transfer
Aug 8, 2012
I have a SG 200-26. Port 1 goes to Internet. Port 2 to a Synology NAS. Port 3 to a 'small' gigabit hub with a computer and a media player connected. All gigabit connections. The media player uses NFS to access a share on the NAS. How do I configure the SG200 to get max throughput?
Reason is: before I used the SG200 I used a standard hub. THroughput was perfect, HD movies played seamless. With the SG200, performance is significantly less. HD movies are not playable.
I tried switching QoS on, ports 2 and 3 to level 7, and off. Did not solve the prob.
View 5 Replies
ADVERTISEMENT
Dec 22, 2011
I own a Sg200-08 and everytime when I transfer a lot of data via the switch it crashs when around of 100GB. Crash means it will stop working until I disconect power and reconect again.I've checked it back with a Netgear 8port device, this works very well. So I can say its defently the switch and not the connected devices.The firmware is the latest one and I've reset to factory defaults, I had no changes from factory defaults in the setup and I changed the devices to other ports.
View 3 Replies
View Related
Jan 3, 2013
Is it possible to import the config of a 5510 to a 5520. Trying to replace two 5510's with 5520's and wondering is there a way import the existing config files for the 5510's into the 5520's?
View 3 Replies
View Related
Oct 26, 2011
I am a novice at setting up Cisco routers, I have a few years of networking form the server side of things just beginning to work on the switch side. I am trying to configure a sg200-8 to have three VLANs.
Here are the steps i used:
Create VLAN:
VLAN
VLAN ID: 10
VLAN Name: 22 lab network
Apply
VLAN
VLAN ID: 20
VLAN Name: 23 lab network
Apply
[code].....
View 7 Replies
View Related
May 24, 2011
SG200-08 and SG200-08P fail to hold or update Date/Time.(New installation for a UC320 setup.)I've got both an SG200-08 and SG200-08P that are failing to maintain date/time when set with "Use Local Settings". Every restart/powercycle causes them to reset to Dec 31 1969. Other settings save fine.I first tried to set time via SNTP Unicast using a variety of public time server addresses including the 3 hard coded to the SG200-08 firmware:
Sadly though it always just shows "Active Server Server Host Address: 0.0.0.0" and continues having 12/31/1969 as the date. Both after a config save and a reboot.I can ping the NTP servers just fine from the switches either by IP or by hostname.At this point I've decided that I must be missing something simple. At least I hope so... otherwise it's a firmware bug which means waiting for a fix.Other devices behind the same firewall/gateway (RVS4000) are updating NTP
View 2 Replies
View Related
Apr 29, 2012
how to connect our new SG200-18 to an existing Cisco network, in particular a C2960S.Here's what I've got:
<----- Rest of network ------- C2960S ----------- SG200 ----- (PC connected directly to the SG200)
On the C2960S-side here's what I've got on the corresponding interface:
interface GigabitEthernet1/0/1
switchport mode trunk
On the SG200-side I've set the IP-address and default-gateway accordingly, however:From the SG200 I can't ping any other host on the same IP-subnet as the switchFrom the SG200 can't ping the default-gatewaycan't ping from any other host or the default-gateway *to* the switch But:On the SG200 I've got plenty of MAC-addresses under "Dynamic Address Table" - however only MAC-addresses that belong to the management-VLAN of the SG200 (i.e. VLAN9 in my case)The MAC-address table on the SG200 even includes the MAC-addresses of hosts on the same VLAN I tried to ping without success. For example: I tried a PING from a host having a MAC-address of 00:19:bb:31:91:30. This MAC shows up in the arp table of the SG200. To cross check I connected a dedicated PC to the SG200 and assign it an IP-address out of the management-LAN-range of the SG200 - in this case I can access the switch (i.e. PING, WEB etc.)So to summarize: Connectivity is OK when going from directly connected devices to the SG200. No connectivity from devices that are behind the C2960S towards the SG200 and vice versa. (The problem is definitely not with the C2960S-side since we've got plenty of them hooked together without problems.) I'm enclosing the screenshots of the corresponding definitions on the SG200.
View 4 Replies
View Related
Apr 16, 2013
I'm baffled by the poor performance that I'm seeing when passing traffic between my two Cisco SG switches.
The configuration is as basic as I can make it, no VLANs, QoS or bonding. Both have been updated to current firmware as part of the troubleshooting process.
When I transfer data within one of my switches I see 50/60Mb/s. When I pass the same traffic between both switches I see 0.6 Mbs/ or less.
I have tried to eliminate every possible factor including switching out the cables. No success.
View 2 Replies
View Related
Dec 2, 2012
We have a project in which we are using 34 Cisco SG200-18's each with a MGBLX1 (LC Single Mode Fiber) SFP mini-GBIC.All the fiber's come back to one building where we must "bridge" all 34 fiber connections. What hardware should be used to accomplish this? A L2 switch? For example, a 12 port SFP Switch with Fiber SFP's accepting the first 12 fiber connections, then other switch with SFP for the next 12 and so on, until there is a overall capacity of 36 and having patch cables between the 3 switches?
what cisco or non cisco hardware would work with these SF200-18's to accomplish this?
View 9 Replies
View Related
Oct 16, 2012
IPsec VPN configured between ASA5525-X and Linksys RV042 ,While transfering some exe from ASA5525-X side to Linksys RV042 side over VPN hash-sum of this file changes, so, when you open transferred file, you have an error message "File is corrupted". If you try to transfer file from Linksys side, hash-sum is ok. Also, work with oracle application is interrupted because of unknown reason. IPsec works only if using router instead of ASA.
View 2 Replies
View Related
Nov 23, 2012
because I have a problem with my wireless connection and have everything configured correctly have done according to the link URL
Every Time I copy a file or multiple files over LAN switch from a PC to PC b become each restart the wireless module and am lost file.
View 6 Replies
View Related
Sep 26, 2011
I have a laptop and a desktop pc both connected to the same wifi network, both running win 7. File transfers are not quick enough for my liking over wifi so when I need to move a few files about I tend to hook the two together with an ethernet cable. When I try to copy a file however it defaults to using the wireless connection. I'm getting around this at the moment by just turning the wifi off on the laptop while I do the transfers but it would be nice to not have to.
View 1 Replies
View Related
Jan 9, 2013
I have RS232 GSM/GPRS modem SIM900,by using this i can send/receive messages, make call.But now my Query is "By using this modem can i able to transfer files between two systems which are located at diffenent places",it is possible or not?
View 3 Replies
View Related
Jun 2, 2012
I am transferring music files from an External HDD link by USB to my laptop to a Synology 410J NAS, I have both a wired and a wireless connection. The NAS is connected to a 2wire modem and router, and so is the laptop. I am getting speeds of between 450KB to 600KB a second i.e. 0.45 to 0.6MB per second. How can I make this faster?
View 1 Replies
View Related
May 16, 2012
We are replacing some netgear switches with the Cisco SG200. The situation is relatively straightforward. We have a series of VLAN's coming in on a trunk from a service provider for our Metro Ethernet locations. These trunks then get cross-connect to various location for connectivity. The problem we have is there are two VLAN's that need to go to the same switch which provides access to our public IP block.
I set up the two VLAN's on the SG200 with the trunk port VLAN tagging on the service provider port. Then I set up a separate port for untagging the traffic with the PVID of the respective VLANS's as follows: [code] The public switch has no VLAN's configured (it is an SG200 too). If I connect GE2 to the public switch everything works fine. When I connect GE3 to the public switch, things die. I thought this might be caused by STP although STP should not be detecting issues like this across separate VLAN's. Disabled STP, no change.The same configuration with the Netgear worked without an issue. FYI, the VLAN's cannot be changed...they are defined by the service provider in this particular case. otherwise we'd just make them the same..
View 11 Replies
View Related
Aug 28, 2011
I need to purchase a few Gigabit PoE switches for a small business and I am thinking that SG200 or SG300 switches are perfect for this purpose.
Layer 3 functionality in SG300 switches is not great - HSRP or any other next-hop redundancy protocol is not supported, dynamic routing protocols are not supported, policy-based routing is not supported, etc. I may get one SG300 switch for inter-VLAN routing so that I do not have to send traffic to a Layer 3 device for this purpose, especially because my Layer 3 device (ASA5505) has only 10/100 Mbps interfaces. All other switches in the network don't have to be Layer 3 switches, and I am thinking of perhaps getting SG200 instead of SG300 swithces. However, because I am a long-time Cisco engineer, and know ins and outs of the IOS CLI, I would much rather administer the switches with CLI rather than GUI. So, do SG200 switches provide CLI (even if it is not officially supported) or is the only Small Business switch platform that supports CLI SG300? I do realize that the OS running on these switches is not IOS, but after having reviewed the CLI manual for SG300, I would say that 90+% of commands are identical to IOS CLI commands.
View 1 Replies
View Related
Feb 17, 2013
I have a couple laptops in my home and just purchased a WD network drive so that a central location can keep all our media files (photos, videos, etc.) and we can access it with our pc's, phones, and tablets. I'm in the process of setting up the HD and transferring all the media to the drive wirelessly however I'm only experiencing about 1.5MB/s-4MB/s. Is there a way to speed this up.
View 2 Replies
View Related
Apr 22, 2012
I have a wireless network with 2 desktop hooked up wired, and one laptop that's wireless. Accessing files on the desktop with xp installed is quick and transfers files at around 5-7mb/s. When I connect to my main pc with windows 7 on it, file transfer is EXTREMELY slow and almost always stutters and freezes. I've tried removing the drive from 'shared' and then adding it again, reinstalling my ethernet driver, swapping ethernet ports on the back of my router, and resetting it altogether. Still a slow transfer speed.I use workgroup all around, for xp and for 7.
View 3 Replies
View Related
Mar 12, 2011
Just relised this problem after trying to leech some stuff from a friend from his pc at a lan My connection seems to go REALLLY slow. Heres a pic nobody else is file copying and its the same from every pc.
View 7 Replies
View Related
Sep 13, 2011
I spoke with two different support agents with a well respected routermanufacturer. I got two different answers - No surprise.So, I ask the forum, what file transfer speeds should I expect when transfering a good sized amount of data (10gig) from wired PC on a 10/100/1000 network router to another PC via wireless connection 20 (feet away + two walls) using 802.11N.Both PC's are new / newer with win 7 64 bit. - Current transfer speeds - Both wired and wireless internet download speed tests are arond 21 meg per second. Both PC's wired and wireless get around 3.7 meg per second internet download (speed tests).At this point - no real difference in internet access between PC's and wired / wireless.
However, when I copy a file from PC1 to PC 2 (both wired) I get 68 megs per second. When I transfer the same data set (10 gig) from PC1 wired to PC 2 wireless, the data transfer falls to 3.7 meg per second. One rep told me to expect about 80% of my wired rate or about 54 megs per second (when using my 802.11N 300meg) equipment. The other rep (same company) told me that the 3.7 meg per second ia about the best I can expect. A transfer rate of 3.7 megs per second simply does not appear to be a reasonable speed given that all my wireless equipment is pretty new and supports numbers that are much higher
View 1 Replies
View Related
Jul 22, 2011
i am connecting my laptop and desktop for file transfers.Both have win XP. i have a airtel modem and i use a cable to connect my laptop or desktop to that modem for internet. Both work fine with the modem and i dont have nay problem in connecting to internet. I am using the same cable to connect the laptop n desktop and i receive message "A network cable is unplugged". Is it that i cannot use this cable for this purpose or something else? the data cabel reads: "Data cable CAT.5 UTP 26AWG 2pair AWM PVC 75deg C EIA/TIA 568B"
View 1 Replies
View Related
Dec 30, 2012
Installed brand new CAT6 cable from my office PC (W7) to my HTPC (W7) to stream movies (150 feet) and I cannot get file transfer speeds higher than 1MBps. I get the sames slow speeds whether I use the router or plug the two PCs together.
View 12 Replies
View Related
Apr 7, 2011
i am running windows server 2008 with the hyper V role installed.i have installed windows 7 Professional as a guest OS. assigned 2 GB of Ram to the machine. the point behind the VM is to virtualize my FTP server and incase a format is required i have the VM file on my 2nd partition, host OS on another. i use Cerberus FTP Server on the Win7 OS. i configured the server to accept SFTP and TLS connections. on the host OS i installed Fire FTP and File Zilla, both Clients will at max download a 4 MB file at 64 KB/Sec .. i have seen both jump to about 80 KB but was only a split second and never held.. however if i login without SFTP and transfer over standard protocol, i download at 1 MB/sec. which is my normal speeds. would this be only to the encryption process?, in the Cerberus Server there are options to adjust download speeds, i have left it default, and altered it to allow its max configuration. My ISP is not limiting any connections that shouldnt be.
View 1 Replies
View Related
Mar 3, 2013
I want transfer heavy files(like Psd format 2GB and more) every day. I tried in normal ftp's they are very slow. I have 10 mbps leased line. i want to speed up file transfer like aspera plugin.
View 1 Replies
View Related
Feb 13, 2011
url...I have 2 PC's connected to a DIR-615 through 802.11n and each have a DWA-130 802.11n adapter. I am running Windows 7 Ultimate 64 bit on both computers. The specs of both systems are very high.I only have these 2 computers on wireless right now. Their signal is full strength, they are less than 10 feet away from the router.I am getting 2.0 MB/s when transferring files between them and although I am not expecting to get 17MB/s, but I should be getting better speed than 2 MB/s.Hard drive specs are Crucial C300 SATA 6.0, WD Caviar Blue SATA 3.0, and WD Caviar Green SATA 3.0. My Green drive reads/writes at 100MB/s, My Blue 125MB/s, and My SSD 225MB/s. So, those are not the bottleneck.Is there any other settings I can try? I have not messed with my DWA-130 settings nor have I messed with Windows.
View 7 Replies
View Related
Dec 27, 2012
I just picked up a pair of 18-port SG200s, and I'm trying to figure out of there's some secret trick to getting CLI access to them? I've upgraded to the latest version of firmware (1.2.7.76) hoping that may work, but no luck.I can tell the guts to support a CLI are there, because writing the config out to a TFTP server shows identical an identical config style to the SG500 I have here.Is there some way to enable it?
View 5 Replies
View Related
May 22, 2011
I am trying to set up three vlans across two switches. The switches are Cisco SG200 and SG 300 series. There are 20 devices connected to the two switches including a router for Internet. Among these devices are five wireless access points all hardwired to the LAN. If I understand correctly the first thing I have to do is aggregate the two switches. I ran two cat5 cables to ports 1 and 2 of each switch. As I understand it all I need to do is to create SAG with the two ports on each switch. I think I need to use tagging but I don't really understand how to do this. Once I get the trunking set up correctly I want to create one vlan to which all devices will belong for Internet access. The other two would be for data and VoIP. Do I create vlans with the same name on both switches? When I assign the devices (by port) do I need to enable tagging? Which type of port setting should I use? I am assuming that by including the acess points in the vlans will mean that any wireless device connected to them will have acess to the Internet and the devices in the same vlan.
View 1 Replies
View Related
Jan 26, 2013
I ma having issues trying to import a .PEM file into an ACE 4710. The original file was a PCKS12 file that was converted to a set of .PEM files as I have no access to any server to do a file transfer. This has worked in the past. the error I get is "Error: File not of recognized types - PEM, DER or PKCS12, import failed". I am not sure what is exactly failing. The cert was converted to a .PEM and the ACE imported that fine.
View 4 Replies
View Related
Sep 11, 2012
Old XP and New W7 side by side. Wanting to transfer file, pics, docs, ect. form one to the other. I can see the old XP from the new W7. Through W7 I can get to documents and settings on the old XP, try to open that and says I dont have permission. Old XP c drive shared on network. Still missing something.
View 11 Replies
View Related
Aug 19, 2012
How can I transfer file from my windows 7 os to virtualbox ubuntu at the same time??
View 3 Replies
View Related
Nov 7, 2011
I am having incredibly slow connection while transferring files using file sharing.I have the below hardware:
108Mbps TPLINK Wireless Router
TL-WR642G 108Mbps TPLINK Wireless Access Point acting as repeater
Laptops accessing internet and folder sharing enabled for local file transfer
Transfering of files excessively slow (after playing around with the settings was able to get 500KBps). I have set all wireless adapters on the laptops to 802.11g only.Tried setting the router and access point to both 54Mbps and 108Mbps 802.11G only as well as b/g.
View 1 Replies
View Related
Jun 27, 2011
I recently switched from an older 10/100 linksys to this gigabit router from D-Link. However, when I try to transfer files from one computer to another on the LAN, the file transfers are ridiculously low, right around 16KB/s. I have CAT6 cable for all connections, but am baffled by what could cause such a slow speed. I'm trying to transfer files from my desktop (win7) to my server (Windows Home Server 2011).
View 3 Replies
View Related
Nov 13, 2008
I have SSH and SCP enabled on the ASA 5510. I can SSH fine into the device. However, I cannot copy files to the device usng WinSCP. Used all options but nothign seems to work. I see the log authentication successful, but then WinSCP reports no response from ASA.
View 5 Replies
View Related
Jul 23, 2012
I have a RV220W operating in 2.4GHz N-only mode. Channel bandwidth is set to 20MHz, channel to 6 (a site survey shows that channel as completely clear), WPA2/AES. I am connected to a TrendNet wireless bridge. The admin page for that wireless bridge shows a link quality of 100% with a signal strength of 71%. If I select a higher channel (11), the signal strength drops to 51%.
I have a Windows 7 PC connected to the Trendnet bridge and a Windows 7 server connected to the RV220W, both via a 1Gbps LAN port. When I transfer a file from the server to the PC or vice versa, I get a lowsy 2MBps (~20Mbps) transfer rate. That seems awfully slow. I tried channel bonding from 20 to 40 MHz
View 2 Replies
View Related
