Cisco VPN :: ASA5525-X - When Transfer File Get Error
Oct 16, 2012
IPsec VPN configured between ASA5525-X and Linksys RV042 ,While transfering some exe from ASA5525-X side to Linksys RV042 side over VPN hash-sum of this file changes, so, when you open transferred file, you have an error message "File is corrupted". If you try to transfer file from Linksys side, hash-sum is ok. Also, work with oracle application is interrupted because of unknown reason. IPsec works only if using router instead of ASA.
View 2 Replies
ADVERTISEMENT
Nov 23, 2012
because I have a problem with my wireless connection and have everything configured correctly have done according to the link URL
Every Time I copy a file or multiple files over LAN switch from a PC to PC b become each restart the wireless module and am lost file.
View 6 Replies
View Related
Sep 26, 2011
I have a laptop and a desktop pc both connected to the same wifi network, both running win 7. File transfers are not quick enough for my liking over wifi so when I need to move a few files about I tend to hook the two together with an ethernet cable. When I try to copy a file however it defaults to using the wireless connection. I'm getting around this at the moment by just turning the wifi off on the laptop while I do the transfers but it would be nice to not have to.
View 1 Replies
View Related
Jan 9, 2013
I have RS232 GSM/GPRS modem SIM900,by using this i can send/receive messages, make call.But now my Query is "By using this modem can i able to transfer files between two systems which are located at diffenent places",it is possible or not?
View 3 Replies
View Related
Jun 2, 2012
I am transferring music files from an External HDD link by USB to my laptop to a Synology 410J NAS, I have both a wired and a wireless connection. The NAS is connected to a 2wire modem and router, and so is the laptop. I am getting speeds of between 450KB to 600KB a second i.e. 0.45 to 0.6MB per second. How can I make this faster?
View 1 Replies
View Related
Feb 17, 2013
I have a couple laptops in my home and just purchased a WD network drive so that a central location can keep all our media files (photos, videos, etc.) and we can access it with our pc's, phones, and tablets. I'm in the process of setting up the HD and transferring all the media to the drive wirelessly however I'm only experiencing about 1.5MB/s-4MB/s. Is there a way to speed this up.
View 2 Replies
View Related
Apr 22, 2012
I have a wireless network with 2 desktop hooked up wired, and one laptop that's wireless. Accessing files on the desktop with xp installed is quick and transfers files at around 5-7mb/s. When I connect to my main pc with windows 7 on it, file transfer is EXTREMELY slow and almost always stutters and freezes. I've tried removing the drive from 'shared' and then adding it again, reinstalling my ethernet driver, swapping ethernet ports on the back of my router, and resetting it altogether. Still a slow transfer speed.I use workgroup all around, for xp and for 7.
View 3 Replies
View Related
Mar 12, 2011
Just relised this problem after trying to leech some stuff from a friend from his pc at a lan My connection seems to go REALLLY slow. Heres a pic nobody else is file copying and its the same from every pc.
View 7 Replies
View Related
Sep 13, 2011
I spoke with two different support agents with a well respected routermanufacturer. I got two different answers - No surprise.So, I ask the forum, what file transfer speeds should I expect when transfering a good sized amount of data (10gig) from wired PC on a 10/100/1000 network router to another PC via wireless connection 20 (feet away + two walls) using 802.11N.Both PC's are new / newer with win 7 64 bit. - Current transfer speeds - Both wired and wireless internet download speed tests are arond 21 meg per second. Both PC's wired and wireless get around 3.7 meg per second internet download (speed tests).At this point - no real difference in internet access between PC's and wired / wireless.
However, when I copy a file from PC1 to PC 2 (both wired) I get 68 megs per second. When I transfer the same data set (10 gig) from PC1 wired to PC 2 wireless, the data transfer falls to 3.7 meg per second. One rep told me to expect about 80% of my wired rate or about 54 megs per second (when using my 802.11N 300meg) equipment. The other rep (same company) told me that the 3.7 meg per second ia about the best I can expect. A transfer rate of 3.7 megs per second simply does not appear to be a reasonable speed given that all my wireless equipment is pretty new and supports numbers that are much higher
View 1 Replies
View Related
Jul 22, 2011
i am connecting my laptop and desktop for file transfers.Both have win XP. i have a airtel modem and i use a cable to connect my laptop or desktop to that modem for internet. Both work fine with the modem and i dont have nay problem in connecting to internet. I am using the same cable to connect the laptop n desktop and i receive message "A network cable is unplugged". Is it that i cannot use this cable for this purpose or something else? the data cabel reads: "Data cable CAT.5 UTP 26AWG 2pair AWM PVC 75deg C EIA/TIA 568B"
View 1 Replies
View Related
Dec 30, 2012
Installed brand new CAT6 cable from my office PC (W7) to my HTPC (W7) to stream movies (150 feet) and I cannot get file transfer speeds higher than 1MBps. I get the sames slow speeds whether I use the router or plug the two PCs together.
View 12 Replies
View Related
Apr 7, 2011
i am running windows server 2008 with the hyper V role installed.i have installed windows 7 Professional as a guest OS. assigned 2 GB of Ram to the machine. the point behind the VM is to virtualize my FTP server and incase a format is required i have the VM file on my 2nd partition, host OS on another. i use Cerberus FTP Server on the Win7 OS. i configured the server to accept SFTP and TLS connections. on the host OS i installed Fire FTP and File Zilla, both Clients will at max download a 4 MB file at 64 KB/Sec .. i have seen both jump to about 80 KB but was only a split second and never held.. however if i login without SFTP and transfer over standard protocol, i download at 1 MB/sec. which is my normal speeds. would this be only to the encryption process?, in the Cerberus Server there are options to adjust download speeds, i have left it default, and altered it to allow its max configuration. My ISP is not limiting any connections that shouldnt be.
View 1 Replies
View Related
Mar 3, 2013
I want transfer heavy files(like Psd format 2GB and more) every day. I tried in normal ftp's they are very slow. I have 10 mbps leased line. i want to speed up file transfer like aspera plugin.
View 1 Replies
View Related
Feb 13, 2011
url...I have 2 PC's connected to a DIR-615 through 802.11n and each have a DWA-130 802.11n adapter. I am running Windows 7 Ultimate 64 bit on both computers. The specs of both systems are very high.I only have these 2 computers on wireless right now. Their signal is full strength, they are less than 10 feet away from the router.I am getting 2.0 MB/s when transferring files between them and although I am not expecting to get 17MB/s, but I should be getting better speed than 2 MB/s.Hard drive specs are Crucial C300 SATA 6.0, WD Caviar Blue SATA 3.0, and WD Caviar Green SATA 3.0. My Green drive reads/writes at 100MB/s, My Blue 125MB/s, and My SSD 225MB/s. So, those are not the bottleneck.Is there any other settings I can try? I have not messed with my DWA-130 settings nor have I messed with Windows.
View 7 Replies
View Related
Jan 3, 2013
Is it possible to import the config of a 5510 to a 5520. Trying to replace two 5510's with 5520's and wondering is there a way import the existing config files for the 5510's into the 5520's?
View 3 Replies
View Related
Jan 26, 2013
I ma having issues trying to import a .PEM file into an ACE 4710. The original file was a PCKS12 file that was converted to a set of .PEM files as I have no access to any server to do a file transfer. This has worked in the past. the error I get is "Error: File not of recognized types - PEM, DER or PKCS12, import failed". I am not sure what is exactly failing. The cert was converted to a .PEM and the ACE imported that fine.
View 4 Replies
View Related
Aug 8, 2012
I have a SG 200-26. Port 1 goes to Internet. Port 2 to a Synology NAS. Port 3 to a 'small' gigabit hub with a computer and a media player connected. All gigabit connections. The media player uses NFS to access a share on the NAS. How do I configure the SG200 to get max throughput?
Reason is: before I used the SG200 I used a standard hub. THroughput was perfect, HD movies played seamless. With the SG200, performance is significantly less. HD movies are not playable.
I tried switching QoS on, ports 2 and 3 to level 7, and off. Did not solve the prob.
View 5 Replies
View Related
Sep 11, 2012
Old XP and New W7 side by side. Wanting to transfer file, pics, docs, ect. form one to the other. I can see the old XP from the new W7. Through W7 I can get to documents and settings on the old XP, try to open that and says I dont have permission. Old XP c drive shared on network. Still missing something.
View 11 Replies
View Related
Aug 19, 2012
How can I transfer file from my windows 7 os to virtualbox ubuntu at the same time??
View 3 Replies
View Related
Nov 7, 2011
I am having incredibly slow connection while transferring files using file sharing.I have the below hardware:
108Mbps TPLINK Wireless Router
TL-WR642G 108Mbps TPLINK Wireless Access Point acting as repeater
Laptops accessing internet and folder sharing enabled for local file transfer
Transfering of files excessively slow (after playing around with the settings was able to get 500KBps). I have set all wireless adapters on the laptops to 802.11g only.Tried setting the router and access point to both 54Mbps and 108Mbps 802.11G only as well as b/g.
View 1 Replies
View Related
Jun 27, 2011
I recently switched from an older 10/100 linksys to this gigabit router from D-Link. However, when I try to transfer files from one computer to another on the LAN, the file transfers are ridiculously low, right around 16KB/s. I have CAT6 cable for all connections, but am baffled by what could cause such a slow speed. I'm trying to transfer files from my desktop (win7) to my server (Windows Home Server 2011).
View 3 Replies
View Related
Nov 13, 2008
I have SSH and SCP enabled on the ASA 5510. I can SSH fine into the device. However, I cannot copy files to the device usng WinSCP. Used all options but nothign seems to work. I see the log authentication successful, but then WinSCP reports no response from ASA.
View 5 Replies
View Related
Jul 23, 2012
I have a RV220W operating in 2.4GHz N-only mode. Channel bandwidth is set to 20MHz, channel to 6 (a site survey shows that channel as completely clear), WPA2/AES. I am connected to a TrendNet wireless bridge. The admin page for that wireless bridge shows a link quality of 100% with a signal strength of 71%. If I select a higher channel (11), the signal strength drops to 51%.
I have a Windows 7 PC connected to the Trendnet bridge and a Windows 7 server connected to the RV220W, both via a 1Gbps LAN port. When I transfer a file from the server to the PC or vice versa, I get a lowsy 2MBps (~20Mbps) transfer rate. That seems awfully slow. I tried channel bonding from 20 to 40 MHz
View 2 Replies
View Related
Mar 28, 2012
I have been trying to get this setup for 2 days now and so far NADA.....
Router: Linksys E3000 - below is a list of all devices connected (hardwired T568B) to the 4 ports with a laptop connected via wireless
1. Main PC - motherboard: ASUS Maximus IV Extreme-Z (dual GB LAN ports)
2. Media Server - motherboard: MSI Z68A-GD80 (dual GB LAN ports)
3. Test Bench AMD PC
4. WD TV Live
Currently: I have all 3 computers running Windows 7 and connected to a Homegroup. I have given the correct permissions to enable sharing of files between each of the 3 computers and can transfer files from one PC to the next w/o any issues.
Desired: I want to connect my Main PC and Media Sever with a crossover cable using the 2nd LAN port on each motherboard, so that I don't have to go through the router to transfer data to and from these 2 PCs. I will have each PC also connected to the Linksys E3000 router via the 1st LAN port on each motherboard to supply the internet connection, so I am also not trying to "share" an internet connection between these 2 PCs. Basically, I want to run my home network through the Linksys E3000 and then a 2nd network for the 2 PCs using the crossover cable.
Current Problem: I disconnected the straight-through cables from the router to each computer from the 1st LAN port. I then connected the crossover cable from the Main PC to the Media Server and setup a new Home network in the Network and Sharing Center in Windows 7. Everything worked and I could transfer data to and from each these 2 PCs, so i know I wired the crossover cable correctly. Then I reconnected the straight-through cables coming from the router to the 1st LAN ports of each mobo, thinking that each PC would auto-detect the internet connection and reacquire my existing home network, enabling an internet connection again. However, this did not happen.
[URL] I also followed this how-to guide on microsoft.com, but when I get to Step 3 where it says that an "Unidentified network icon" will aprear in the Network and Sharing Center, it does not!
From Googling, reading, and troubleshooting I believe I know 2 things:
1. All of the hardware is functioning properly - when the straight-through cables from the router are disconnected, the 2 PCs are networked through the crossover cable and files can be transferred.
2. The problem is with Windows 7 somewhere - I think?
View 1 Replies
View Related
May 7, 2012
How can i connect my PC with laptop with LAN cable for high speed file transfer?
View 2 Replies
View Related
May 6, 2012
My XBOX started complaining when I began using Windows Media Center to stream videos from my PC to my XBOX. I found out that I had a wireless G router provided by verizon which wasn't fast enough to stream videos. SO, I went out and purchased a 4500EA router expecting it to be the fastest thing I had ever seen.
Now it seems a bit slow when trying to stream video from my laptop to the XBOX and i'm a tad bit confused as to why. So I did a file transfer from a desktop wired directly to the router from a laptop in the same room wirelessly connected to the network and my speed is about 4mbps. 4MBPS!? This device is supposed to be capable of moving packets LAN side at 450MBPS.
Both of my PC's are quad core, newer model PCs. I've tried moving files now for several hours with the same results. I've toyed around with my wireless adapters, changed power settings, full duplex, half, changed mtu sizes, changed security settings. I'm out of ideas.
Is getting about 1% of the advertised bandwidth normal?
View 2 Replies
View Related
Feb 23, 2012
1 newer build computer connected to D-link 655 via Cat6.1 laptop computer connected to same D-link 655 via Wireless N minicard. (Intel) (130Mbps connected) Router on a 10 foot shelf, always have full bar in wireless strength on 2nd computer.
Both computers can upload and download as expected from the internet. Transfers between the two computers though are slow. Both computers are loaded with Windows 7. Transferring files to or from the laptop transfers at 1.5MB/sec to 2 MB/sec.
View 1 Replies
View Related
Oct 31, 2012
I have the attached setup. now i would like to limit my ftp transfer to 10 mb from a specific vlan to ftp server on the STM-4 (622) link. what would be the best way to limit ftp traffic to 10 mb .Video_Main#sh verCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)Technical Support:
[URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Tue 26-Apr-11 18:09 by prod_rel_team
Image text-base: 0x100A0994, data-base: 0x13CAB728
ROM: 15.0(1r)SG1Jawa Revision 7, Snowtrooper Revision 0x0.0x116
Video_Main uptime is 15 weeks, 3 days, 23 hours, 53 minutesSystem returned to ROM by power-onSystem restarted at 16:38:21 UTC Wed Nov 23 2011Running default software
License Information for 'WS-X45-SUP7-E' License Level: entservices Type: Permanent Next reboot license Level: entservices
cisco WS-C4506-E (MPC8572) processor (revision 8) with 2097152K/20480K bytes of memory.Processor board ID FOX1502GZHFMPC8572 CPU at 1.5GHz, Supervisor 7Last reset from PowerUp9 Virtual Ethernet interfaces204 Gigabit Ethernet interfaces10 Ten Gigabit Ethernet interfaces511K bytes of non-volatile configuration memory.
Configuration register is 0x2101
Video_Main#
View 6 Replies
View Related
Dec 10, 2012
From 6.0.199.4 to AIR-CT5500-K9-7-3-101-0.aes. Get the error below halfway through download of file to controller.
*Dec 11 14:18:55.775: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4158 Error FTP file Transfer [ftp_get], <28>, No space left on device.
I have no idea how to delete files form the storage on the 5508? TFTP transfer gives me this error after the upload is done:
% Error: Code file transfer failed - Error while writing output file
*Dec 11 15:11:45.514: %TFTP-3-FILE_WRITE_FAIL: tftp_client.c:517 Error while writing 512 bytes to file. Tftp error.
*Dec 11 15:11:45.514: %TFTP-3-WRITE_NOCLOSE_FAIL: tftp_client.c:147 Error while writing the local file: No space left on device
*Dec 11 15:11:45.514: %OSAPI-3-FILE_WRITENOCLOSE_FAILED: osapi_file.c:582 Failed to write 512 bytes (FileDesc:64). file write no close failed
View 6 Replies
View Related
Feb 10, 2011
just bought a WD my book world edition 2 NAS and have been trying to tranfer files wirelessly to it but a 700mb file is taking 25mins to trans. my book is connected by ethernet to netgear dgnd3300 router and my laptop has sitecom 300n usb doongle.is there some sort of setting i've missed or is this speed normal?
View 5 Replies
View Related
May 13, 2013
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
wdr3500 problem with usb external hard drive when I try to transfer files from computer to usb on the router it'll work for small files like MP3. But files like MKV where they can be 1-2gb will cause a disconnect and fail to transfer the file. The whole drive would disconnect and windows will give an I/O error.
View 8 Replies
View Related
Nov 3, 2012
This is another E3000 "connection drops" thread. Some background: I have two E3000's that are cascaded. The main router is in my basement connected to my cable modem and is my DHCP server. The second one is on the main floor and provides my wireless signal (no DHCP, and is hard connected to the main router).I have lots of connection drops with the wireless router on the main floor. Lately I have noticed a trend, though. My connection drops mostly when I browse my network (usually browsing pictures on another computer) or when large files or videos are being transferred. If I connect a cable, I have no problems. When wireless, I have signal drops.I have tried every trick and tip that I've seen on this forum or been provided in the Linksys FAQ. I've changed the beacon interval, fragmentation threshold to 2306 and CTS to 2307, I've tried changing channels, I've checked and unchecked boxes for NAT, Filters, etc. I've tried different combinations of WPA2 passwords. I've tried dynamic routing, static routing, blah blah blah...
When I set the 5Ghz channel to Auto(DFS) it defaults to channel 36 and 144Mbps. When I use other channels, I get 300Mbps. Either way, my connections still drops.
I have the latest firmware 1.0.04 Build 6.I even have the router sitting on top of a laptop cooling pad to keep it cool.No matter what I do, as soon as I start browsing my network the wireless connection drops.I am so frustrated! I upgraded my WRT-160N to this E-300 router to get the faster speed and dual band but have had nothing but trouble. I never had a connection drop with my 160N.
EDIT: I notice that when my signal drops, I can see the power LED blinking on the router, like it's going through a reboot cycle.
View 9 Replies
View Related
Mar 3, 2011
I have two machines that both have WUSB600N wireless network adaptors with a Cisco WRT160N router. The file transfer speeds between the two devices maxes out at 1.6Mbs. If I run speed tests off the internet I hit 15 to 20 and downloads are excellent. I have played with all kinds of settings for the driver and router but nothing seems to work. Both these devices are running Windows 7. I tried a file transfer with an XP device as well and it maxes at about 1.6. how to increase the bandwidth??
View 1 Replies
View Related
