Cisco Switches :: SG300 - How To Reboot Unresponsive IP Camera
Aug 26, 2012
I have a Synology NAS that is connected to several IP Cameras through a SG300 switch. From time to time the IP cameras become "disconnected" at random When I reboot the switch, the access to cameras is re-established.
Problems: it requires an external device to reboot the switchall ports are shutdown while rebooting the switch
Q1 Is there a way to program the SG300 to reboot itself automatically every X hours?
Q2 Is there a way to automate the following process on the SG300 switch itself. ping a camera every 1 minutesafter three unresponsive ping, shutdown and restart the port to which the camera is connected
View 7 Replies
ADVERTISEMENT
Aug 9, 2011
My SG300-52 is struck in reboot loop after i set tcp congestion avoidance in webui.
********************************************
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
[code]....
i've tried flashing new firmware via xmodem but still have problem.
View 1 Replies
View Related
Aug 31, 2012
I have two Cisco SG300-20 switches. Both of them are configured in L3 mode. They have several VLAN's configured.
When I reboot my switches some VLAN membership settings are lost! I have already saved the settings over and over before rebooting, and even tried to save it to the backup memory and so on. Say for example I have changed port 9 to 14 from VLAN 101 to VLAN 105. I save the configuration, reboot the switch. And then the changes are lost. This is a big problem, because servers and my iSCSI network loose connectivity. They already have the latest firmware. This issue was there three firmwares before.
This issue pop-ups when I have a power loss, or I need to reboot/shutdown them manually. It may be off-topic but I also have the feeling that the performance of the switches goes down during uptime. A reboot solves the performance issue. I don't have a performance benchmark, but I can notice it on the performance transfer rate between clients and servers.
View 4 Replies
View Related
Dec 4, 2011
Running the newest firmware available
$ show version
SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
This is how I can cause the reboot to happen every time.
$ show lldp neighbors GE 10
Device ID: <mac address>
Port ID: 22
Capabilities: Bridge
[Code]....
View 1 Replies
View Related
Mar 12, 2012
I have an SG300-52 gigabit switch that has been constantly rebooting and is effectively unusable.This started after Enabling TCP Congestion Avoidance, specifically:
-Turned on TCP CA
-Saved Running Config -> Startup Config
-Rebooted Switch
Since then the switch has been rebooting roughly every half a minute, and the management (HTTP) interface is inaccessible. In addition the factory reset (i.e. reset button for greater than 10 seconds) does not make a difference. I suspect that there is some bug with TCP CA that causes the switch to fail to start up, and that factory reset has failed to clear the startup config.
View 2 Replies
View Related
Oct 17, 2010
Any way to schedule a reboot of a DCS2102?I've got 3 of them here, and they are very good but every now and then they seem to stop writing to the storage. They haven't frozen cause I can still connect to them via a browser
View 2 Replies
View Related
Aug 3, 2009
Have 13 DCS-920 Every few days a few random cameras will will hang/become unresponsive at random intervals. The cameras require that I unplug the cameras before they will respond. When the cameras are unresponsive I cannot access the camera via a web browser, the D-View Cam software, or the setup wizard. This is a problem as they are all mounted in positions requiring a ladder to access.
I have some connected via 802.11g and other hard wired over 10/100 cat-6 Ethernet cable.
View 14 Replies
View Related
Jun 20, 2011
Have several DCS-5300 cameras (firmware 1.06) and randomly the cameras will reboot.
D-Link says to set to factory default, but that is not physically possible.
View 1 Replies
View Related
Aug 29, 2011
These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
View 1 Replies
View Related
May 26, 2011
1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
View 2 Replies
View Related
Feb 8, 2012
Can I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies
View Related
Jul 25, 2012
I have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies
View Related
Nov 21, 2011
I'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
3COM Setup
#
interface GigabitEthernet1/0/1
[Code].....
View 2 Replies
View Related
Jan 1, 2013
We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each. Switch was connected to HQ Network as untagged VLAN 101. I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great. Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
I then Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.
View 10 Replies
View Related
Dec 18, 2011
does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
View 2 Replies
View Related
Aug 7, 2011
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies
View Related
Aug 20, 2012
I'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
View 3 Replies
View Related
Jan 19, 2012
I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies
View Related
Apr 22, 2012
I have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies
View Related
Mar 13, 2012
I am in the process of preping our network for the installation of an IP Camera based security system on it will be running within VLAN 600 in our network, and management would prefer that general users are not even aware it is there.
16 Cameras will all be running off two SF302-8P Switches that will be uplinked to our Cisco 2960 Access Switches. Due to port limitations I need to daisy chain the two SF302 Switches.
ACCESS-302-CA-01 - Ge1 uplinked to Port on ACCESS-03 (Cisco 2960) On this switch Fe1-8 Need to be in VLAN 600 to communicated with the camera server which will be plugged directly into Ge2 on Access 302-02.
ACCESS-302-CA-02 - Ge1 Uplinked to Ge2 on ACCESS-302-01
Ge2 - connected to the Network Video Recorder.
I've defined the VLAN's in the switch and have VLAN 600 as Untagged for FE1-8.
how do I configure Ge1 and Ge2 on each switch to pass the appropriate VLAN conntent to the devices connected?
View 1 Replies
View Related
Jun 20, 2012
My company uses the SG 300-10 and SF 300-08 switches to deliver services to our customers. We have been using the upgraded firmware version 1.1.2.0. Our normal procedure is to configure the switches in house and upgrade the firmware before sending them out to the customers. The configurations are confirmed in house after the new firmware has been loaded. Recently we have had several of these switches lose the Vlan configuration that we setup. These incidents have occurred after power outages and scheduled reboots. We do not generally have to reboot our customer switches.
View 11 Replies
View Related
Apr 4, 2013
We have several SF-300-48P switches, eveytime there is a power failure the switches need to reboot 2 or 3 times before they are able to route packets again.
View 1 Replies
View Related
Jul 24, 2011
I am unable to connect vivotek ip7137 camera with d link or netgear router I tried all my best made the connection with eithrnet cable , reset both machine set static ip of pc but nothing is happening?
View 1 Replies
View Related
May 3, 2011
I have a couple of SF300-24 switches. When I made needed configurations using CLI or GUI and then saved all configurations. The problem is that switches do not save configurations after reboot.
View 2 Replies
View Related
Mar 9, 2013
Cisco SG200-26 (not PoE model). After a power failure, at restart the switch seems unable to reboot. The power led starts blinking in green, after some seconds the connected ports start blinking as well, but the the switch reboots automatically after few more seconds.I tried to disconnect lan cables, power cord, and reset to factory by pressing and holding down the proper button for 30s and more, but no success.In the small amount of time the switch's ports seem to be powered up, clients don't receive packets, don't ping each other or the switch manage address.
View 1 Replies
View Related
Mar 10, 2012
I have a problem with switches SPS208G2. They're conected with SFP module after Linksys SPS224G4 and another swithes. After reboot switches which are conected with SPS208G2 don't see link. However previous switches phisical link status is up show LED, but protocol status is down show command "show interface status". I changed Firmware, it doesn't work, i changed SFP module it doesn't work. Yesterday i got new Firmware ls_sps2xx_bx-10600.ros but no luck. I don't understand what's wrong with switches SPS208G2. I have 500 or 700 switches SPS208G2. They installed different places at city. They don't ping until reboot their or previous switches. Reboot previous switches usually doesn't work, works only physical reboot or pulling SFP module.
View 1 Replies
View Related
Nov 15, 2011
We have 3 sf-300 series switches in Layer3 mode deployed in different offices. We have found that approximately every 2-3 months at all 3 locations users experience a serious reduction in bandwidth. Only after rebooting the cisco does the problem go away and we're okay for another few months. some setting/feature that may be contributing to this? We are only using several ports and 1 static route on each switch. We are not using any of the bells and whistles on the switch. 2 of the switches are using the original firmware, whereas the other is using the newest firmware. Maybe this is just what we should expect from a Small Business switch?
View 18 Replies
View Related
May 9, 2011
I have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.
View 2 Replies
View Related
Jul 19, 2012
On my SG300 I set up LAG for the last two ports.
I then plugged them into my SRW224G4P, once I do that I get dropped packets.
I was thinking maybe doing firmware upgrades to both switches?
View 3 Replies
View Related
Jan 29, 2012
I need to know how to configure each port in switch SG300-10 to vlans, i need to configure one port "trunk" with catalyst switch and assign 4 ports to different vlans. any solution?
View 2 Replies
View Related
Jun 20, 2012
In the CLI documentation for the SG 300 Series, it shows sh ip route rip as a command. I have installed the latest firmware and that command is no longer available. Does the SG300 series support RIP?
View 6 Replies
View Related
Jan 27, 2013
We purchased a SG300-52 last week to replace a 5yr old Dlink which has worked perfectly. 1 day after the SG300 went it it started crashing with this fatal error problem so I reverted the firmware back from 1.2.7.76 (latest) to 1.1.2.0 but I still get the problems. It crashes when I have it on my lan with users connected or if I just have the switch on my desk with just my laptop connected, so it cant be a load issue or a network topology issue. I already have a Cisco SGE2010 on my network without problems.
View 7 Replies
View Related
Mar 15, 2011
I have a question about ACL and binding. I have a SG300 28P and a couple of other linksys switches and Access points that are connected to it via trunks. The cisco SG300 28P is running in layer3 mode and i have created a couple of vlans and one of them is a guest vlan. Now to my question, i create an ACL and an ACE that vill funktion so that guest vlan only can connect to the internet and not the rest of the internal network. And then i must bound the ACL to an interface port or lag, what i can see it is not possible to bind it to an vlan? so if i have a port on some of the other switches that is member of the guest vlan, vill the ACL on the SG 300 stop guest vlan trafic to the internal network that is comming from some of the other switches?
View 1 Replies
View Related
