Cisco Switching/Routing :: 1941 - Security Certification / SMART NET Package
Jan 12, 2012Recently i purchased 1 no Cisco router 1941 from vendor but he didn't active Cisco security certification or SMART NET package.
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Router 1941 Security License?
Mar 12, 2013I have a cisco router 1941 and i have uploaded before evaluation license , now i have already bought cisco security license .I have already installed on cisco router , but the problem the router is still using the evaluation license not the new license .
RSP#sh flash:
-#- --length-- -----date/time------ path
1 55088360 Oct 10 2012 06:04:10 +00:00 c1900-universalk9-mz.SPA.151-4.M4.bin
2 2903 Feb 4 2013 12:23:32 +00:00 cpconfig-19xx.cfg
[Code].....
Cisco Switching/Routing :: 1941 Port-Security With Router Switch Module
Feb 29, 2012I have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE). I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings. Is port-security no available on the switch modules?
View 3 Replies View RelatedCisco Security :: ASA 5505 Failed To Unzip AnyConnect Package
Nov 28, 2011There is ASA 5505:
- 8.4(2) IOS
- FLASH: 128 Mb
- DRAM: 256 Mb
Requirements for 8.4(2) are acomplished: For the ASA 5505, only the Unlimited Hosts license and the Security Plus license with failover enabled require 512 MB; other licenses can use 256 MB.Are installed latest AnyConnect packeges for linux, some smatphones (each 4-5 MB). But for Windoes it's 21 MB and we got error "Failed to unzip the Anyconenct Package". In prior IOS version there was command cache-fs limit, by default it was 20 Mb. As i understand ASA now dinamically determines amount of cache memory and it's not enough. Because of the increased size of the AnyConnect package from 4MB in AnyConnect 2.5 to 21 MB in AnyConnect 3.0, you may need to upgrade the ASA flash and memory card first.If your ASA has only the default internal flash memory size or the default DRAM size (for cache memory) you could have problems storing and loading multiple AnyConnect client packages on the ASA. Even if you have enough space on the flash to hold the package files, the ASA could run out of cache memory when it unzips and loads the client images.So there is a question, after DRAM upgrade to 512 MB will be there enough cache memory for Anyconnect packeges with total size 35-40 Mb?
Cisco Switching/Routing :: Smart Call Home Usage On The ASA 5520 Or RHL
Jun 25, 2012I'm trying to install a Gateway in Red Hat Linux to Cisco Smart Call Home Service, and reading about this in google, i find this info:Smart Call Home on the ASA This is much more simply to configure and operate.I want to know what solution is more recomended and why.
View 1 Replies View RelatedProtocols / Routing :: Cisco Certification - What Happens When Router Doesn't Know Path To Network
Apr 3, 2012I'm studying for a Cisco certification and I'm trying to wrap my head around the routing. I understand how routers work for the most part and how the get updates about networks and how many hops away they are, but I don't get what happens when a router doesn't know the path to a network.
View 19 Replies View RelatedCisco Switching/Routing :: 1941 / Policy Based Routing With Two Default Routes
Jun 24, 2012I have a 1941 router configured for Policy based routing with two ISPs.Two static default routes configured to point the gateways of respoective ISPs with same metric.But the problem is, packets are going throug the one ISP only while doing traceroute.
N/W connectivity:
ISP1-----> <----------------------> LAN1
| Router |
ISP-------> <----------------------> LAN 2
Below is my configuration :
Current configuration : 5958 bytes
!
! Last configuration change at 05:18:56 UTC Mon Jun 25 2012
!
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
Cisco Switching/Routing :: DHCP For PC At G0/1 From G0/0 For 1941
Mar 12, 2013I have this Cisco 1941 router with two Ethernet ports g0/0 and g0/1. The g0/0 is connected to office LAN with internet access. As my office LAN is DHCP, it will assigned a IP address for g0/0 since this g0/0 is configured as "ip address dhcp". Now my question is that i have a group of 5 pcs, namely PC1, PC2, PC3, PC4 and PC5 that is connected to the switch and one of the ports of this switch is connected to g0/1 of Cisco 1941. Is it possible that let say PC2 and PC3 (both DHCP enabled) could access the internet access from g0/0 and at the same time, the office LAN assigned IP address for PC2 and PC3 automatically?
Office Lan with internet access (DHCP) (Default gateway 10.0.0.1)
|
|
g0/0 (DHCP enable) (DHCP assigned IP address 10.0.0.138)
Cisco router 1941
g0/1
|
|
HP Switch
|
PC1 PC2 PC3 PC4 PC5
Is this operation possible? if possible, how to configure inside the router 1941 to achieve this objective?
Cisco Switching/Routing :: 1941 Cannot Login To CP
Oct 15, 2012I have just set up my Cisco 1941 router to my cable internet connection. I have access to everything, but I cant login successfully into Cisco CP.
I set up a new user with level 15 privileges and a secret password. I go to login via webbrowser and I put in my credentials, but I get rejected. I have tested the username and password via the CLI, and it works fine, I just cant seam to login to Cisco CP.
Cisco Switching/Routing :: 1941 Keeps On Rebooting?
Nov 26, 2012I've got a 1941 router that keeps on rebooting by itself every minute. currently, there's no power issue.
I've detected the show version returned a bus error. Is this an IOS bug?
ROUTER uptime is 1 minute
System returned to ROM by bus error at PC 0x222FE2D4, address 0xD0D0D71 at 14:27:13 SGT Tue Nov 27 2012
[Code].....
Cisco Switching/Routing :: 1941- Ip Next Hop Unreachable
Sep 11, 2012I have a strange behavior and a simple proble . I configured the following static route
ip route 10.84.22.0 255.255.254.0 10.84.23.254
That I advertsied in eBGP :
router bgp 65000
network 10.84.22.0 mask 255.255.254.0
the IP next hop 10.84.23.254 is cascaded on my customer LAN . At nominal time the router advertsed the route in BGP
pjnb1376#sh ip bgp nei 57.213.169.169 ad
Next Hop Metric LocPrf Weight Path
*> 10.84.22.0/23 10.84.23.254 0 32768 i
When the lan interface of the router goes down , the router still advertise the route !!! Even if the IP next hop
10.84.23.254 is not reacheable anymore ....
The box is a Cisco 1941 using
1900-universalk9-mz.SPA.151-4.M1
Cisco Switching/Routing :: 1941 Router Cannot Get To Internet From PC On LAN
Mar 12, 2012I am having an issue accessing the internet from a PC on the LAN. I have configured the PC with the gateway of the router infront of the ISP to test. I can ping from the router to google or any other internet IP. From the PC I can ping to the GIG0/1 (Inside LAN IP) and the GIG0/0 (Outside WAN IP going to ISP) but I can't ping the Next Hop IP of the ISP or anything past that. If I do a trace route from the PC to the google IP address it hits the GIG0/1 Inside LAN IP Address but fails from there. Here is a cut down snap shot of the router configure
[code]....
Cisco Switching/Routing :: 1941 - SSH Not Working From Internet
Feb 12, 2012I have a Cisco 1941 router configured using Cisco Configuration Professional... SSH management works from the LAN IP 10.0.1.254 and 10.0.2.254 Also, SSH management works from the LAN using the external domain name which resolves to the public IP address.
The problem i have is if I try SSH from the internet to the public IP.. nothing happens.
cisco1941#show config
Using 18498 out of 262136 bytes
!
! Last configuration change at 13:57:49 PCTime Tue Feb 14 2012 by admin
[Code].....
Cisco Switching/Routing :: Setting Up VPN For 1941 Router?
Sep 6, 2012im having trouble setting up a vpn for a 1941 router this is what I have setup
crypto isakmp policy 10
encr aes 256
authentication pre-share
crypto isakmp key ########## address 63.247.48.50
[code]....
my whole problem comes about when i need to Nat 192.168.1.0 to 10.12.14.0/24 before it goes through the tunnel.
Cisco Switching/Routing :: Firmware Update For 1941 ISR
Mar 5, 2013I bought a secondhand small business router (model 1941 Integrated Services Router) for personal use. It runs version IOS 15.0(1)M1 software, which seems to work well, but I'd like to download a firmware update that addresess some of the security flaws in this software. When I tried the download process it told me I need to buy a service contract first? Is this right, or am I doing something wrong?
View 1 Replies View RelatedCisco Switching/Routing :: Router 1941 But Can't Do Ipsec
Oct 10, 2012I did have a router cisco 1941 but can not do ipsec with it,i did take a smart net.
View 3 Replies View RelatedCisco Switching/Routing :: 1941 Specific Parameters
Aug 9, 2012I’m looking for some specific parameters of Cisco 1941 and not able to find them .
1. Maximum number of DHCP clients2. Maximum number of DHCP pools3. Maximum number of V LANs on trunk port.
Cisco Switching/Routing :: EHWIC4ESG Card Into 1941
Apr 4, 2013Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
Cisco Switching/Routing :: 1941 - How To Setup PBR To Have Two Host
Feb 22, 2012I have a 1941W that has a connection to my ISP (Gi0/1) and another connection to a remote lab (Gi0/0). Everything is working fine how it is setup. All my traffic from my internal networks can access the Internet and devices on the 192.168.201.0 /24 can access the Internet and the lab 10.89.0.0/16.
Now I want to have two devices (192.168.201.51 & .147) use Gi0/0 when accessing host 63.85.190.67. There is no route to this subnet since it reside in the remote lab. Here is what I have right now. How would I setup a PBR to have those two host use Gi0/0 when accessing 63.85.190.67
interface Vlan192
ip address 192.168.201.1 255.255.255.0
ip nat inside
ip virtual-reassembly (code)
Cisco Switching/Routing :: 1941 Setting Up With Pxe-booting
Aug 22, 2012I have a new cisco 1941 router that I am setting up with pxe-booting. I have never setup pxebooting before and i have this setup so far ip dhcp pool Admin
-option 66 ip 192.168.1.4
-option 67 ascii pxelinux.0
and i can pull an ip but it keeps getting hung up when it comes to the TFTP part.
Cisco Switching/Routing :: 1941 - Configuration Of WLAN AP
Apr 5, 2013I have a Cisco router 1941 connected to a switch. I'm configuring the w LAN- AP and i need to have the wireless devices have an ip in the same range of the wired devices.Since i cant use the same ip range on the gig0/1 and the V LAN 1 for the wireless, i wanted to know how to config the giga0/1 connected to the switch to act as a layer 2 port and i keep the ip on the v LAN 1.
View 9 Replies View RelatedCisco Switching/Routing :: 1941 Router Does Not Keep Config When Turned Off?
Aug 22, 2012I have a 1941 integrated services router that will not keep the configs. After several atempts of saving running config to the startup config, then rebooting the device. I am having to reload the configs manually from TFTP because they are gone. I have also tryed the "wr" command to see. Is there a proper way to shutdown this particular type of router?
View 2 Replies View RelatedCisco Switching/Routing :: Factory Resetting 1941 Router
Oct 27, 2011What is the procedure to reset a 1941 router to factory defaults? I just recieved my1 1941 router. I connected it up to my Mac using USB. I got loged in using the cisco/cisco login and it said it will only work once and that I should create a new account. So I entered the command as directed on the screen and it gave my an error about the command. I verified it three times and each time it rejected. While I was looking online for an answer the connection timed out and now I can't get back in.
View 1 Replies View RelatedCisco Switching/Routing :: Replacing 1841 12.4 Advsec With 1941 15.2M SEC/K9
Jul 2, 2012I decided recently to switch out our border router (1841 12.4 advsecurity) with a shiny new 1941 (15.2 SEC/K9) as the CPU upgrade was needed.The core below acts as a VPN end point to various other remote offices we have, all of which have a similar network design at each end (and all entirely managed by me). All of these are still running 1841's with 12.4 advsecurity on them as well. These are all GRE tunnels with ipsec procection on them (not crypto maps). [code]
Everything else works fine (NAT, route-maps etc), it's just these IPSEC/isakmp tunnels that are not playing ballIt's definitely not an ARP issue (all arps were cleared) and ICMP appears to work fine (ie, I can ping the remote tunnel's public IP endpoint from the core using the loopback for that tunnel as the source). I am suspecting it's something strange with the stateful firewall config, but I did try and apply ipsec and isakmp-msft to the ip inspect list, with no success.
Cisco Switching/Routing :: 1941 Don't Have Access To Config At Moment
Oct 28, 2012I don't have access to my config at the moment and I haven't had a chance to get to the console of this router as of yet.A little background info:This is a Cisco 1941 router in which I have multiple NAT inside interfaces for internal VLANs. Before my current problem I was using one NAT outside interface for Internet access with another NAT outside connecting to our corporate network that was in a shutdown state.The router is performing router on a stick and had layer 3 subinterfaces for each VLAN. I have ACLs filtering on each subinterfaces allowing only the traffic I need through.I also currently only have one static NAT port for an FTP server.The time finally came when I had to connect our corporate network to this router via an access port on a 2950 which trunks to the router.The problem comes when I send any traffic to the subinterfaces on the corporate network which is the second NAT outside interface on the router. The main point for this connection is to do a static NAT from this interface to a web server on another VLAN. Any traffic to this interface including just pinging from the outside causes connection to the router to fail for about 3-4 min.Like I said I haven't ha the chance to get to the console yet Sony cant tell everything that happens. Nothing shows up in the logs after I can get connection back and the router didn't reboot as a "show version" says the router has been up for a long time.The CPU is also usually very low as not that much traffic flows through this router at a time.I built a very similar network in packet tracer and it works just fine.
View 1 Replies View RelatedCisco Switching/Routing :: 1941 Router Interface Binding
May 16, 2012Router 1941 is installed with additional 4 Gig-interfaces card; we have 4 ADSL Router with 4 MB connections. I need to connect all the ADSL connection to the router 4 port and combine them into 16 MB, is there any way to combine 4 Gig interfaces?
View 4 Replies View RelatedCisco Switching/Routing :: To Setup NVI On 1941 Router - Configuration
Dec 9, 2012Here is my current config, how to enable and setup NVI on a cisco 1941 router.i think it would fix my issue but i'm unclear on how to implement it to test.
i would like to be able to access an internal server from an outside address.
Cisco Switching/Routing :: 1941 / IPSec Tunnel Up No Traffic?
Mar 7, 2013I have an IPSec tunnel configured on my Cisco 1941. The other device is an ZyXEL router.I can see the tunnel is up but there is no traffic.This comes out the show crypto ipsec sa
interface: Dialer1
Crypto map tag: CMAP_AVW, local addr 10.10.10.89
protected vrf: (none)
local ident (addr/mask/prot/port): (192.168.200.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.150.0/255.255.255.0/0/0)
current_peer 20.20.20.161 port 500
[code]....
Cisco Switching/Routing :: 1941 Configuration With Range Of WAN IP Addresses
Oct 23, 2011I have a 1941 router tt needs to be setup with the range of WAN ip addresses ip nat inside outside don't allow me to use it..How can i configure on the router to ensure from outside i'm able to access to firewall (129.2.1.2) ?
View 4 Replies View RelatedCisco Switching/Routing :: 1941 - Set Up 2 VLANs To Connect To Two Networks?
May 27, 2013We have a Cisco 1941 with the 8 port EHWIC (with 8 layer 2 gig ports). We are trying to do something very basic .We need to set up 2 VLANs (vlan 10 & vlan 20) to connect to 2 networks - Server & Users.The Internet connection (via a comcast modem) is connected to the G0/0 port of the 1941 and it just gets a DHCP address.
[code]...
Cisco Switching/Routing :: To Prioritize Traffic 1941 And 2951
Jul 1, 2012We need to give TCP 3389 & 3399 priority over all other traffic between a Cisco 1941 and 2951.What is needed to do this?
View 6 Replies View RelatedCisco Switching/Routing :: 1941 Ethernet Load Balance?
Mar 5, 2013I'm setting up a lot of small remote sites that are only reachable via VHF ethernet radios that operate at 32k. I'm going to be using 2 of these radios shooting to two seperate base station radios to provide diversity. I'm going to have a Cisco 1941 sitting between the two radios and the way I have it configured now is to only use one radio and the second is only sitting there in case the primary fails. I was thinking though that I could load balance them to give a little more throughput. The devices at these sites are really low speed but we like to use snmp to monitor everything that is ethernet so I wanted to give as much bandwidth as I can.
Will load balancing work in this situation? What would the basic configuration be? This is all internal to our network so there are no ISPs to deal with. We're using C1900-UNIVERSALK9-M IOS will that work or will I need to change that?
Cisco Switching/Routing :: 2960 G / 1941 - Network Design
Jun 14, 2012I have been recently asked to design a network. What I have for equipment is four 2960G's and one 1941 router. One switch is a root switch and the other three will have end devices on them.I have decided on three V lans to go with: VLAN20 Data, VLAN30 ISCSI, and VLAN99 Management each with seperate trunk links and redundancy (see picture below).
I have a seperate trunks for each V lan using the switch port trunk allowed. With exception to the Data V lan.My design has the Data V lan as the native because it is going to be receiving untagged traffic from the external network. I have set up inter v lan routing on the 1941 via sub-interfaces to allow them to talk to each other (or because of allowed they cannot?). I have one port coming from my router to my switch via Ethernet cable which is my bridge out. I have my external port doing a NAT translation for my inside addresses and a Default route set up ip route 0.0.0.0 0.0.0.0 gig0/0. I am using rapid- PVST to prevent loops and provide my zero downtime convergence when a link goes down. As it stands right now I cannot talk out of my network or inside of my network.
You can see it is highly redundant and I do not want to change it. This network is going to be deployed but there will never be anybody physically there to manage it which is why I made it as redundant as humanly possible.