Cisco Switching/Routing :: 3560 Download Not Available / Missing
Oct 11, 2012
I am currently doing an audit at a customer site, i.e. am checking if any IOS upgrades are needed. I have found that alot of IOS versions that the customer is running are not available in the Cisco Software Download area anymore. Taking IOS 12.2(44)SE2 for the 3560 for example: some earlier and later versions are available as downloads, but this exact version is not. It also is not listed as a deferred version.What is Cisco telling us with this exactly? Are these "missing" versions not supported anymore i.e. is an upgrade to a supported version adviseable?
I've finally got my 3560 switch IPv6 capable (IP Services IOS), but I've stumbled upon something strange: I can configure a tunnel interface, but I can't put the tunnel in ipv6ip mode. The command is missing. I can choose GRE, IP in IP, and a bunch of other things, but no ipv6ip. I'm a bit desperate here and probably I am going to have to live with it, but just in case? I need the IPv6 tunnel for an uplink to a tunnel broker which only supports this type of tunnel, and I'm surprised this is missing.
I have a 867VAE-K9. On feature navigator it is listed as supporting OSPF. However when I go into config mode and type "router ?" BGP is there, but OSPF is not. Also, under my tunnel interfaces there is no support for any OSPF commands such as "ip ospf cost" etc. I'm in the process of raising a TAC. I have tried five or six different versions of IOS code that is available for this device, in each, we never see OSPF listed but sometimes see "router odr" or "router lisp"...
I've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
We have a working PBR route map on a 6509 switch and a 3750 switch, each in different locations.On both devices, the route-map is configured to match on one of multiple ACLs, then set the next hop to a directly-connected IP address, like so: [code]
When copying in the ACL contents for "ACL20", they were accidentally copied in to the ACL1 list, and ACL20 was never created. Shortly after this was done, the next hop router went unreachable in both locations. Pings failed and the 6509 and 3750 each lost the EIGRP adjacency to the 1.1.1.5 router. After troubleshooting, I removed "match ip address ACL20" and connectivity returned.
My question is...if a PBR route-map tries to match on a non-existent ACL, what happens? Does it mark the next hop unreachable (even though it's directly connected) or does it match for ALL traffic and send *everything* there (thus, making it appear unreachable, as if a broadcast storm was happening)?
I just loaded the web interface IOS on a C3750X. The first thing I noticed was there was basically no web interface. I can look at things, and do default configurations on ports, but it doesn't appear I can configure VLANs or QoS or anything like that.
Am I missing something, or is this just how the web interface functions?
i'm trying to type the command (config)#spanning-tree mode rapid-pvst on my Cisco 2950, but (config)#spanning-tree mode ? only shows me one option - pvst. I've checked the Cisco support page which suggests my version of IOS should support rapid-pvst.
Switch_1#sh ver Cisco Internetwork Operating System Software IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(13)EA1, RELEASE SOFTWARE (fc1)
I have one VLAN on a 3750 where I do not see any MAC addresses even though it is in use. This is an unrouted VLAN between a WLC on a port- channel /LAG and an access port to an ASA for guest traffic. When I do a show MAC add I get nothing for VLAN 60 (guest DMZ) but all other VLANs seem to be OK. Spanning tree is not showing TC counters incrementing either.
I also was told when put a port on this VLAN the laptop did not get a DHCP address form the ASA, but the wireless guest clients are working fine. I can see the DHCP leases and ARP entries in the ASA and the ASA ARP in the WLC so some traffic is passing fine. I'm not onsite right now so troubleshooting is all remote which limits some options.
I have got a l2 link of 512 kbps from two different ISP. I want to aggegrate the bandwidth of this connection so that I can feel like having 1 mbps connection. I am not actually talking about load balancing, but bandwidth/link aggegration. Can we have the solution of failover with different vlan from different isp ? Can we be able to make the link as a single link.
After deleting configuration with „write erase“ and reloading, our Cisco Catalyst 4503 with version cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin, and licence ipbase, doesn't recognize any command regarding SSH. We tried configuring SSH key with „crypto key generate“, but that command is not recognized either.
I recently rebuilt the configuration of our Cat6500 multilayer device for use as a user stack. The device is funtioning as it should be, but I am unable to set SSH using the 'crypto key generate rsa' command. The crytop command isn't avaiable at all, which suggests a firmware issue.
I have configured a hostname and Ip domain-name and the image is the only one available.
The show version output is listed below. show verCisco Internetwork Operating System SoftwareIOS (tm) s72033_rp Software (s72033_rp-IPSERVICES_WAN-VM), Version 12.2(18)SXF12, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2007
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
I have tried to make policy based routing on Cisco 3560. I use ipservices ios (SW version 12.2.(50)SE3 and SW-IMAGE C3560-IPSERVICESK9-M) For below configuration there is no problem and pbr is working.
“Access-list 100 permit ip host 1.1.1.1 host 2.2.2.2 Access-list 101 permit ip host 1.1.1.1 host 3.3.3.3 Route-map pbr1 permit 10 Match ip address 100 Set ip next-hop verify-availability 1.1.1.2 1 track 11 interface fasthethernet 0/1 ip policy route-map pbr1”
But when i add another sequence to the "pbr1" with another sequence number like that.
“Route-map pbr1 permit 11 Match ip address 101 Set ip next-hop verify-availability 1.1.1.3 1 track 12”
pbr is not working. Switch gives message "PLATFORM_PBR-3-UNSUPPORTTED_RMP:Route-map pbr1 not supported for Policy Based Routing”"ip policy route-map pbr1" command not shown in the running config. And "show ip policy" output is blank.Configuration guide says you have insert many sequence to the route-map with the same name. And also this command is not in the unsupported command list.
I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch. The switch is running the following IOS version: [code]
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
What would be the best way to get the two workstations talking via the switch?
I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B Network A. 10.0.12.0/24 Network B 10.0.24.0/24
The configuration is interface Vlan1 description Data VLAN
We recently purchased Cisco 3560X Layer3 Switch. We need to perform simple Inter VLAN routing. We have configured VLAN1 (name-server_vlan) and VLAN2 (name- user_vlan). We have also assigned the Ports and IP address to both the VLANs. After assiging this if we plug Laptop A into VLAN1 then it doesnt communicates with Laptop B (btw, Laptop A is able to Ping VLAN2 Gateway ) in VLAN2 but on the other hand Laptop B is able to communicate with Laptop A and ping everything i.e. Gateway of VLAN1.
I have a 2504 WLC connected to a Catalyst 3560 which has multiple vlans and is connected to a 2800 series router. I know the catalyst is L3 but I am needing nat functions to get outside to the internet. From my 2800 series router I am able to ping out to the internet, also I am able to ping the vlan interfaces on the catalyst switch. Problem is from the catalyst switch I can ping the inside and outside address of the 2800 but I cannot get any further then that. I cannot ping the 2800 router gateway. Not sure what I am doing wrong as far as routing.
I am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
I am trying to upgrade the IOS in 3560 but I am facing one issue. Its flash is 15MB & available space is 8MB whereas the IOS is of 11MB. How can I upgrade the IOS without upgrading the flash?
We bought a 3560 PoE switch to replace tons of PoE-injectors but when connecting the devices our logs were flooded with
Mar 11 15:09:20.725: %ILPOWER-7-DETECT: Interface Fa0/7: Power Device detected: IEEE PD Mar 11 15:09:20.725: %ILPOWER-5-INVALID_IEEE_CLASS: Interface Fa0/7: has detected invalid IEEE class: 7 device. Power denied Mar 11 15:09:20.968: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, changed state to down Mar 11 15:09:20.985: %ILPOWER-7-DETECT: Interface Fa0/7: Power Device detected: IEEE PD Mar 11 15:09:20.985: %ILPOWER-5-INVALID_IEEE_CLASS: Interface Fa0/7: has detected invalid IEEE class: 7 device. Power denied
While the message seems quite clear im wondering if there's any workaround on the problem?
I have a Cisco SW ( 3560 ) with one Trunk link to my router ( 7606 ), Trunk link is fully utilized so i need to add 2nd Trunk.Shall all move some customers from old trunk to 2nd one and create a new subterface for them ?I am think if i can create bundle and add subinterfaces under this bundle ?Add two GE ports to be memeber of this bundle ?
We have a IP-phone system connected to port 1 on a 3560 switch, the phone system tags traffic with dscp. The switch uplink is on port 24. Is this configuration correct:
I have a 3560, which is being used as our core router that I have recently installed. It still has the standard IOS which came with (C3560E-UNIVERSALK9-M) it but I need to implement policy based routing so need to upgrade it and have downloaded c3560-ipservicesk9-mz.122-58.SE2.bin and indeally would like to install it in the morning before people start work.
I have 2 questions, 1, Is the ipservices capable of PBR as I have been reading conflicting reports, in fact my friend who works for Cisco has advised that it is not possible on the 3560.
2, When I do upgrade will there be any current configurations that are not compatible with the new one, I wouldnt image that there would be any but just wanted to make sure as it would be the biggest headache ever if it went wrong.
I have a 3560 POE that will no longer boot and I am not able to load a fresh copy of software onto it. It appears that it has lost all data. When I attempt to TFTP a new IOS, I receive that following error:
Transfer cancelled by remote system
I have tried using dir flash: to see what is contained in the flash directory but I receive the below message:
unable to stat flash/: no such device
I am stuck in rommon mode so when I do switch: dir command, I don't even see flash as being a filesystem. The below list are the only systems registered.
